Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Hydrocarbon trap”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1966

Fully Deuterated Aliphatic Hydrocarbons Obtained From Iron Carbide Treated with DCl and D2O

According to Oparin, Mendeleev thought that the origin of petroleum was the result of the hydrolysis of iron carbides by superheated steam under pressure from the deep interior of the Earth through geological formations where the metal carbides exist. As early as 1877, Mendeleev described the reaction leading to the synthesis of hydrocarbons according to the general equation 3Fe(sub m)C(sub n) + mH2O yields mFe3O4 + C(sub 3n)H(sub 8m). Other experimental studies on the production of hydrocarbons from cast iron have been reported. Because of the possibility that hydrocarbons may have been trapped within the carbon matrix of the cast iron, which usually has a high content of carbon, we have studied the reaction of pure iron carbide with deuterium chloride and deuterated water. This was done in order to distinguish any newly formed deuterated hydrocarbons from any possible impurities of trapped hydrocarbons. The experiments were carried out by simply allowing iron carbide to react with concentrated deuterium chloride in D2O. The volatile hydrocarbon fraction examined by gas chromatography-mass spectrometry (GC/MS), using a Finnigan 1020/OWA instrument. contained low molecular weight hydrocarbons in a range C3 to C7. Lower molecular weight hydrocarbons were not detected by GC/MS because the MS scanning mode was preset above mass 40 to exclude components of air. The identified hydrocarbons are similar to those obtained under prebiotic conditions using high frequency discharge. The hydrocarbons found in common were propane, butane, pentane, 3-methylpentane, hexane, and heptane. The percent yields decline with increasing carbon number (propane 11%, n-heptane 1%). Similar results have been obtained by the direct treatment of metal carbides by pulse laser vaporization mass spectrometry. These results show that the hydrolysis of iron carbides may have been a significant source of hydrocarbons on the primitive Earth. There appears to be a predominance of straight chain isomers, which may have been important in the prebiotic synthesis of membrane-forming compounds.

Marquez, C.↗
DOE OSTI2020

A comparative study of silver- and palladium-exchanged zeolites in propylene and nitrogen oxide adsorption and desorption for cold-start applications

Here, silver and palladium ion-exchanged BEA zeolites (Si/Al = 12.5) and silver ion-exchanged ZSM-5 zeolites (Si/Al = 15) were studied for their ability to adsorb and desorb propylene and NO under simulated diesel exhaust conditions. The adsorption experiment results demonstrated the excellent ability of bare BEA zeolites to adsorb propylene, but only a small amount of NO. The presence of H 2 O inhibited the adsorption of both C 3 H 6 and NO. Ion-exchanging BEA zeolites with Ag (1.2 and 5.1 wt.% Ag/BEA) attenuated the inhibiting effect of H 2 O on C 3 H 6 adsorption, while NO storage remained inhibited. Adsorption experiments indicated that C 3 H 6 and NO competed with each other for Pd sites with C 3 H 6 showing stronger adsorption compared to NO, whereas Ag sites preferentially adsorbed C 3 H 6 . DRIFTS data indicated the formation of nitrate, formate and acetate species on Ag and Pd, while C 3 H 6 and NO adsorption was also observed on the zeolite hydroxyl groups in the absence of H 2 O. However, the C 3 H 6 and NO adsorption on the zeolite hydroxyl groups was significantly inhibited in the presence of H 2 O. Additionally, nitrosyl, acrolein and carbonate species were formed over 1.0 wt.% Pd/BEA. The effluent analysis during the temperature-programmed desorption in the DRIFTS reactor revealed that adsorbed C 3 H 6 and NO reacted during the release to form oxidation reaction byproducts. The 1.0 wt.% Pd/BEA zeolite showed the greatest oxidation ability during desorption with the majority of stored C 3 H 6 converted to CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1974

An evaluation of the suitability of ERTS data for the purposes of petroleum exploration

This experiment was designed to determine the types and amounts of information valuable to petroleum exploration extractable from ERTS data and the cost of obtaining the information using traditional or conventional means. It was desired that an evaluation of this new petroleum exploration tool be made in a geologically well known area in order to assess its usefulness in an unknown area. The Anadarko Basin lies in western Oklahoma and the panhandle of Texas. It was chosen as a test site because there is a great deal of published information available on the surface and subsurface geology of the area, and there are many known structures that act as traps for hydrocarbons. This basin is similar to several other large epicontinental sedimentary basins. It was found that ERTS imagery is an excellent tool for reconnaissance exploration of large sedimentary basins or new exploration provinces. For the first time, small and medium size oil companies can rapidly and effectively analyze exploration provinces as a whole.

Collins, R. J.↗
NASA NTRS1974

An evaluation of the suitability of ERTS data for the purposes of petroleum exploration

This investigation was undertaken to determine the types and amounts of information valuable to petroleum exploration that are extractable from ERTS data and to determine the cost of obtaining the information from ERTS relative to costs using traditional or conventional means. In particular, it was desirable to evaluate this new petroleum exploration tool in a geologically well-known area in order to assess its potential usefulness in an unknown area. In light of the current energy situation, it is felt that such an evaluation is important in order to best utilize technical efforts with customary exploration tools, by rapidly focusing attention on the most promising areas in order to reduce the time required to go through the exploration cycle and to maximize cost savings. The Anadarko Basin lies in western Oklahoma and the panhandle of Texas (Figure 1). It was chosen as a test site because there is a great deal of published information available on the surface and subsurface geology of the area, there are many known structures that act as traps for hydrocarbons, and it is similar to several other large epicontinental sedimentary basins.

Everett, J. R.↗
NASA NTRS2008

Energy Deposition Processes in Titan's Upper Atmosphere

Most of Titan's atmospheric organic and nitrogen chemistry, aerosol formation, and atmospheric loss are driven from external energy sources such as Solar UV, Saturn's magnetosphere, solar wind and galactic cosmic rays. The Solar UV tends to dominate the energy input at lower altitudes of approximately 1100 km but which can extend down to approximately 400 km, while the plasma interaction from Saturn's magnetosphere, Saturn's magnetosheath or solar wind are more important at higher altitudes of approximately 1400 km, but the heavy ion plasma [O(+)] of approximately 2 keV and energetic ions [H(+)] of approximately 30 keV or higher from Saturn's magnetosphere can penetrate below 950km. Cosmic rays with energies of greater than 1 GeV can penetrate much deeper into Titan's atmosphere with most of its energy deposited at approximately 100 km altitude. The haze layer tends to dominate between 100 km and 300 km. The induced magnetic field from Titan's interaction with the external plasma can be very complex and will tend to channel the flow of energy into Titan's upper atmosphere. Cassini observations combined with advanced hybrid simulations of the plasma interaction with Titan's upper atmosphere show significant changes in the character of the interaction with Saturn local time at Titan's orbit where the magnetosphere displays large and systematic changes with local time. The external solar wind can also drive sub-storms within the magnetosphere which can then modify the magnetospheric interaction with Titan. Another important parameter is solar zenith angle (SZA) with respect to the co-rotation direction of the magnetospheric flow. Titan's interaction can contribute to atmospheric loss via pickup ion loss, scavenging of Titan's ionospheric plasma, loss of ionospheric plasma down its induced magnetotail via an ionospheric wind, and non-thermal loss of the atmosphere via heating and sputtering induced by the bombardment of magnetospheric keV ions and electrons. This energy input evidently drives the large positive and negative ions observed below approximately 1100 km altitude with ion masses exceeding 10,000 daltons. We refer to these ions as seed particles for the aerosols observed below 300 km altitude. These seed particles can be formed, for example, from the polymerization of acetylene (C2H2) and benzene (C6H6) molecules in Titan's upper atmosphere to form polycyclic aromatic hydrocarbons (PAH) and/or fullerenes (C60). In the case of fullerenes, which are hollow spherical carbon shells, magnetospheric keV [O(+)] ions can become trapped inside the fullerenes and eventually find themselves inside the aerosols as free oxygen. The aerosols are then expected to fall to Titan's surface as polymerized hydrocarbons with trapped free oxygen where unknown surface chemistry can take place.

Sittler, Edward C., Jr.↗
DOE OSTI2020

Nanoarray-Based Monolithic Adsorbers for SO 2 Removal

Nanoarray-based monolithic catalysts have been developed for various applications, including CO oxidation, hydrocarbon combustion, lean NO x trapping, and low-pressure CO 2 hydrogenation. In this work, SO 2 adsorption properties have been explored and evaluated on the cordierite honeycomb monoliths grown with zinc oxide nanoarray (ZnO), zinc oxide nanoarray washcoated by BaCO 3 nanoparticles (ZnO/BaCO 3 ), and manganese oxide nanowire array with cryptomelane structure (MnO x ) at a temperature range from 50 to 425 °C. All samples show temperature-dependent SO 2 adsorption behaviors. The adsorption results reveal the performance order: MnO x > ZnO/BaCO 3 > ZnO, with ~ 90% SO 2 adsorbed in MnO x at 425 °C. Washcoated BaCO 3 contributes to the improvement of SO 2 adsorption in ZnO nanoarray, and the best performance displayed in MnO x may be attributed to their high specific surface area. After regeneration, nanoarrays all exhibit good thermal stability during test-regeneration cycles. No additional phase is formed in regenerated ZnO nanoarrays (ZnO-R), while BaCO 3 is converted to BaSO 4 in the regenerated ZnO/BaCO 3 nanoarrays (ZnO/BaCO 3 -R), and the sulfur species (possibly MnSO 4 ) and Mn 2 O 3 are found in regenerated MnO x nanoarrays (MnO x -R). It is noted that a small amount of sulfur species (possibly MnSO 4 ) may promote the SO 2 adsorption of MnO x -R at a lower temperature, while the formed Mn 2 O 3 contributes to the deactivation of MnO x -R.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Impact of Mineral Reactive Surface Area on Forecasting Geological Carbon Sequestration in a CO2-EOR Field

Mineral reactive surface area (RSA) is one of the key factors that control mineral reactions, as it describes how much mineral is accessible and can participate in reactions. This work aims to evaluate the impact of mineral RSA on numerical simulations for CO2 storage at depleted oil fields. The Farnsworth Unit (FWU) in northern Texas was chosen as a case study. A simplified model was used to screen representative cases from 87 RSA combinations to reduce the computational cost. Three selected cases with low, mid, and high RSA values were used for the FWU model. Results suggest that the impact of RSA values on CO2 mineral trapping is more complex than it is on individual reactions. While the low RSA case predicted negligible porosity change and an insignificant amount of CO2 mineral trapping for the FWU model, the mid and high RSA cases forecasted up to 1.19% and 5.04% of porosity reduction due to mineral reactions, and 2.46% and 9.44% of total CO2 trapped in minerals by the end of the 600-year simulation, respectively. The presence of hydrocarbons affects geochemical reactions and can lead to net CO2 mineral trapping, whereas mineral dissolution is forecasted when hydrocarbons are removed from the system.

58 GEOSCIENCES↗
NASA NTRS1985

Multistage open-tube trap for enrichment of part-per-trillion trace components of low-pressure (below 27-kPa) air samples

A multistage open-tube trap for cryogenic collection of trace components in low-pressure air samples is described. The open-tube design allows higher volumetric flow rates than densely packed glass-bead traps commonly reported and is suitable for air samples at pressures below 27 kPa with liquid nitrogen as the cryogen. Gas blends containing 200 to 2500 parts per trillion by volume each of ethane and ethene were sampled and hydrocarbons were enriched with 100 + or - 4 percent trap efficiency. The multistage design is more efficient than equal-length open-tube traps under the conditions of the measurements.

Ohara, D.↗
NASA NTRS1991

A geochemical assessment of possible lunar ore formation

The Moon apparently formed without appreciable water or other relatively volatile materials. Interior concentrations of water or other volatile substances appear to be extremely low. On Earth, water is important to the genesis of nearly all types of ores. Thus, some have reasoned that only abundant elements would occur in ore concentrations. The definition and recognition of ores on the Moon challenge the imaginations and the terrestrial perceptions of ore bodies. Lunar ores included solar-wind soaked soils, which contain abundant but dilute H, C, N, and noble gases (including He-3). Oxygen must be mined; soils contain approximately 45 percent (wt). Mainstream processes of rock formation concentrated Si, Mg, Al, Fe, and Ca, and possibly Ti and Cr. The highland surface contains approximately 70 percent (wt) feldspar (mainly CaAl2Si2O8), which can be separated from some highland soils. Small fragments of dunite were collected; dunite may occur in walls and central peaks of some craters. Theoretical extensions of observations of lunar samples suggest that the Moon may have produced ores of trace elements. Some small fragments have trace-element concentrations 10(exp 4) times higher than the lunar average, indicating that effective geochemical separations occurred; processes included fractional crystallization, silicate immiscibility, vaporization and condensation, and sulfide metamorphism. Operations of these processes acting on indigenous materials and on meteoritic material in the regolith could have produced ores. Infalling carbonaceous meteorites and comets have added water and hydrocarbons that may have been cold-trapped. Vesicles in basalts, pyroclastic beads, and reported transient events suggest gag emission from the lunar interior; such gas might concentrate and transport rare elements. Large impacts may disperse ores or produce them through deposition of heat at depth and by vaporization and subsequent condensation. The main problem in assessing lunar resources is the ignorance about the largely unexplored Moon.

Haskin, Larry A.↗
NASA NTRS2010

Selection of Environmentally Friendly Solvents for the Extravehicular Mobility Unit Secondary Oxygen Pack Cold Trap Testing

Freon-113(TradeMark) has been used as a chemistry lab sampling solvent at NASA/JSC for EMU (extravehicular Mobility Unit) SOP (Secondary Oxygen Pack) oxygen testing Cold Traps utilized at the USA (United Space Alliance) Houston facility. Similar testing has occurred at the HSWL (Hamilton Sundstrand Windsor Locks) facility. A NASA Executive Order bans the procurement of all ODS (ozone depleting substances), including Freon-113 by the end of 2009. In order to comply with NASA direction, HSWL began evaluating viable solvents to replace Freon-113 . The study and testing effort to find Freon-113 replacements used for Cold Trap sampling is the subject of this paper. Test results have shown HFE-7100 (a 3M fluorinated ether) to be an adequate replacement for Freon-113 as a solvent to remove and measure the non-volatile residue collected in a Cold Trap during oxygen testing. Furthermore, S-316 (a Horiba Instruments Inc. high molecular weight, non-ODS chlorofluorocarbon) was found to be an adequate replacement for Freon-113 as a solvent to reconstitute non-volatile residue removed from a Cold Trap during oxygen testing for subsequent HC (hydrocarbon) analysis via FTIR (Fourier Transform Infrared Spectroscopy).

Steele, John↗
NASA NTRS2000

An abiotic origin for hydrocarbons in the Allan Hills 84001 martian meteorite through cooling of magmatic and impact-generated gases

Thermodynamic calculations of metastable equilibria were used to evaluate the potential for abiotic synthesis of aliphatic and polycyclic aromatic hydrocarbons (PAHs) in the martian meteorite Allan Hills (ALH) 84001. The calculations show that PAHs and normal alkanes could form metastably from CO, CO2, and H2 below approximately 250-300 degrees C during rapid cooling of trapped magmatic or impact-generated gases. Depending on temperature, bulk composition, and oxidation-reduction conditions, PAHs and normal alkanes can form simultaneously or separately. Moreover, PAHs can form at lower H/C ratios, higher CO/CO2 ratios, and higher temperatures than normal alkanes. Dry conditions with H/C ratios less than approximately 0.01-0.001 together with high CO/CO2 ratios also favor the formation of unalkylated PAHs. The observed abundance of PAHs, their low alkylation, and a variable but high aromatic to aliphatic ratio in ALH 84001 all correspond to low H/C and high CO/CO2 ratios in magmatic and impact gases and can be used to deduce spatial variations of these ratios. Some hydrocarbons could have been formed from trapped magmatic gases, especially if the cooling was fast enough to prevent reequilibration. We propose that subsequent impact heating(s) in ALH 84001 could have led to dissociation of ferrous carbonates to yield fine-grain magnetite, formation of a CO-rich local gas phase, reduction of water vapor to H2, reequilibration of the trapped magmatic gases, aromatization of hydrocarbons formed previously, and overprinting of the synthesis from magmatic gases, if any. Rapid cooling and high-temperature quenching of CO-, H2-rich impact gases could have led to magnetite-catalyzed hydrocarbon synthesis.

Non-NASA Center↗
DOE OSTI2020

Chemical changes in thirdhand smoke associated with remediation using an ozone generator

Ozonation is a common remediation approach to eliminate odors from mold, tobacco and fire damage in buildings. Little information exists to: 1) assess its effectiveness; 2) provide guidance on operation conditions; and 3) identify potential risks associated with the presence of indoor ozone and ozonation byproducts. The goal of this study is to evaluate chemical changes in thirdhand smoke (THS) aerosols induced by high levels of ozone, in comparison with THS aerosols aged under similar conditions in the absence of ozone. Samples representing different stages of smoke aging in the absence of ozone, including freshly emitted secondhand smoke (SHS) and THS, were collected inside an 18-m 3 room-sized chamber over a period of 42 h after six cigarettes were consumed. The experiments involved collection and analysis of gas phase species including volatile organic compounds (VOCs), volatile carbonyls, semivolatile organic compounds (SVOCs), and particulate matter. VOC analysis was carried out by gas chromatography/mass spectrometry with a thermal desorption inlet (TD-GC/MS), and volatile carbonyls were analyzed by on-line derivatization with dinitrophenylhydrazine (DNPH), followed by liquid chromatography with UV/VIS detection. SVOCs were extracted from XAD-coated denuders and Teflon-coated fiberglass filters in the absence of ozone. In those extracts, tobacco-specific nitrosamines (TSNAs) and other SVOCs were analyzed by gas chromatography with positive chemical ionization-triple quadrupole mass spectrometric detection (GC/PCI-QQQ-MS), and polycyclic aromatic hydrocarbons (PAHs) were quantified by gas chromatography with ion trap mass spectrometric detection (GC/IT-MS) in selected ion monitoring mode. Particulate matter concentration was determined gravimetrically. In a second experiment, a 300 mg h -1 commercial ozone generator was operated during 1 h, one day after smoke was generated, to evaluate the remediation of THS by ozonation. VOCs and volatile carbonyls were analyzed before and after ozonation. Extracts from fabrics that were exposed in the chamber before and after ozonation as surrogates for indoor furnishings were analyzed by GC/IT-MS, and aerosol size distribution was studied with a scanning mobility particle sizer. Ozone concentration was measured with a photometric detector. An estimated 175 mg ozone reacted with THS after 1 h of treatment, corresponding to 58% of the total O 3 released during that period. Fabric-bound nicotine was depleted after ozonation, and the surface concentration of PAHs adsorbed to fabric specimens decreased by an order of magnitude due to reaction with ozone, reaching pre-smoking levels. These results suggest that ozonation has the potential to remove harmful THS chemicals from indoor surfaces. However, gas phase concentrations of volatile carbonyls, including formaldehyde, acetaldehyde and acetone were higher immediately after ozonation. Ultrafine particles (UFP, in most cases with size <60 nm) were a major ozonation byproduct. UFP number concentrations peaked shortly after ozonation ended, and remained at higher-than background levels for several hours. Based on these results, minimum re-entry times after ozone treatment were predicted for different indoor scenarios. Clearly defining re-entry times can serve as a practical measure to prevent acute exposures to ozone and harmful ozonation byproducts after treatment. This study evaluated potential benefits and risks associated with THS remediation using ozone, providing insights into this technology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1991

Short-period comets

The spacecraft flybys of Comet Halley in 1986 confirmed Whipple's icy conglomerate hypothesis for cometary nuclei and showed that comets are far richer in volatiles than any other class of solar system bodies. Water is the most abundant volatile, comprising roughly 80 percent of the gas flowing out from the nucleus. Carbon monoxide is next with a content of 15 percent relative to water, though with approximately half of that coming from an extended source in the cometary coma, i.e., hydrocarbon dust grains. The detection of large numbers of hydrocarbon CHON grains was one of the more significant discoveries of the Halley flybys, as was the ground-based observation that CN occurs in jets, again indicating an extended source. Evidence was also found for more complex hydrocarbons. Estimates of the total dust-to-gas ratio for Halley range as high as 2:1, indicating that a substantial fraction of the volatile material may be tied up in solid hydrocarbons rather than ices. The role of clathrates in trapping more volatile ices is not yet understood. If Halley can be taken to be representative of all short-period comets, then the short-period comets may provide a significant source of volatiles in near-earth space. This resource is more difficult to reach dynamically than the near-earth asteriods, but the high volatile content may justify the additional effort necessary. In addition, there is considerable evidence that at least some fraction of the near-earth asteriods are extinct cometary nuclei which have evolved into asteroid orbits, and which may contain significant volatiles buried beneath an insulating lag-deposit crust of nonvolatiles. Knowledge of comets will be greatly enhanced in the near future by the Comet Rendezvous Flyby mission now under development by NASA, and by the proposed Rosetta mission.

Weissman, Paul R.↗
NASA NTRS2005

NASA Tech Briefs, January 2005

Topics covered include: Fiber-Optic Sensor Would Monitor Growth of Polymer Film; Sensors for Pointing Moving Instruments Toward Each Other; Pd/CeO2/SiC Chemical Sensors; Microparticle Flow Sensor; Scattering-Type Surface-Plasmon-Resonance Biosensors; Diode-Laser-Based Spectrometer for Sensing Gases; Improved Cathode Structure for a Direct Methanol Fuel Cell; X-Band, 17-Watt Solid-State Power Amplifier; Improved Anode for a Direct Methanol Fuel Cell; Tools for Designing and Analyzing Structures; Interactive Display of Scenes with Annotations; Solving Common Mathematical Problems; Tools for Basic Statistical Analysis; Program Calculates Forces in Bolted Structural Joints; Integrated Structural Analysis and Test Program; Molybdate Coatings for Protecting Aluminum Against Corrosion; Synthesizing Diamond from Liquid Feedstock; Modifying Silicates for Better Dispersion in Nanocomposites; Powder-Collection System for Ultrasonic/Sonic Drill/Corer; Semiautomated, Reproducible Batch Processing of Soy; Hydrogen Peroxide Enhances Removal of NOx from Flue Gases; Subsurface Ice Probe; Real-Time Simulation of Aeroheating of the Hyper-X Airplane; Using Laser-Induced Incandescence To Measure Soot in Exhaust; Method of Real-Time Principal-Component Analysis; Insect-Inspired Flight Control for Unmanned Aerial Vehicles; Domain Compilation for Embedded Real-Time Planning; Semantic Metrics for Analysis of Software; Simulation of Laser Cooling and Trapping in Engineering Applications; Large Fluvial Fans and Exploration for Hydrocarbons; Doping-Induced Interband Gain in InAs/AlSb Quantum Wells; Development of Software for a Lidar-Altimeter Processor; Upgrading the Space Shuttle Caution and Warning System; and Fractal Reference Signals in Pulse-Width Modulation.

Source record↗
NASA NTRS1997

Cryptoblemes: A New Discovery with Major Economic Implications and Profound Changes to the Geologic Paradigm

Cryptoblemes are subtle impact shock signatures imprinted by cosmic debris on the crustal surfaces of lunar planetary bodes. These signatures constitute a complex cumulative overprinting of topographic, structural geophysical, and tectonic patterns that have a conspicuous radial centric multiringed symmetry. The geometry and distribution of cryptoblemes on Earth is comparable to the size and density of impact features on lunar planetary surfaces. Analysis of satellite imagery, sea-floor sonar, side-looking radar and aerial photographs of specific sites reveals new criteria for the identification and confirmation of impact-shock signatures. These criteria include joint and foliation patterns with asbestiform minerals, ribbon-quartz, spheroidal weathering, domal exfoliation, pencil shale, and shock spheres, which may originate from hydrocavitation of water-saturated sedimentary rocks. Cryptoblemes may also be associated with breccia pipes, sinkholes, buttes, mesas, and bogs, high-Rn anomalies, nodular concentrations, and earthquake epicenters. Major implications of cryptobleme identification include exploratory targeting of hydrocarbon and mineral deposits and the explanation of their origins. Analysis of known mineral deposits, structural traps and sedimentary basins show a direct correlation with cryptobleme patterns. Significant geologic paradigm shifts related to cryptoblemes include mountain building processes, structural orogenies, induced volcanism, earthquake origins, hydrocarbon diagenesis, formation mineral deposits, continental rifting, and plate movements, magnetic overprinting and local regional, and global geologic extinction and speciation patterns. Two figures provide a comparison between a multiring impact overprint in water and multiring cryptobleme in the U.S. basin range. (Additional information is contained in the original document).

Windolph, J., Jr.↗
DOE OSTI2025

Preliminary Testing of a Continuous Cryopump for Primary Fusion Device Pumping and Direct Internal Recycling

Here, the concept of directly recirculating fusion machine exhaust gas, bypassing the tritium plant, to make fuel pellets was proposed in the 1990s and later termed direct internal recycling (DIR). In the DIR concept, the residual fusion fuel in the machine exhaust stream is separated from impurities locally and diverted directly to the fueling systems, bypassing isotopic separation and other processing equipment, and therefore significantly reducing the required size of the fuel processing plant, reducing plant inventory, and thus increasing the economic viability of fusion as an energy source. One concept for DIR consists of a series of cryogenic pumps to separate the impurities from the machine exhaust gas using different triple point temperatures and saturation curves of exhaust constituents. In this concept, the plasma exhaust is initially passed through an impurity trap operating at ~25–30 K to desublimate impurities such as hydrocarbons, argon, oxygen, and nitrogen. The resulting process stream will consist of DT fuel and helium. The process stream is then pumped by a continuous cryopump known as a “snail pump.” This pump is a steady-state continuous cryopump that desublimates all remaining exhaust gas constituents while allowing helium, a byproduct of the fusion reaction, to pass through. The helium is pumped to the tritium plant for processing while the desublimated material is continuously scraped off, heated up, and transported to the fueling system. This article will present the cryogenic DIR concept and outline the design and operation of the snail pump, along with results from preliminary testing. Tests to assess pumping and separation efficiency found that at D2 flows below 50.7 Pa ⋅ m3/s with 1% helium, the pump is capable of pumping and separating the gas with a resulting DIR fraction of >99%, with no helium entrained in the primary fuel exhaust stream. The main limitation is due to the thermal performance of the cryogenic circuits of the pump, which will be addressed in future testing.

Gebhart III, Trey E. [Oak Ridge National Laborator↗
NASA NTRS1994

Direct Monitoring of Trace Atmospheric Species via Ion Trap Mass Spectrometry

There is an ever-increasing emphasis on the part of government agencies, academia, and industry on enhancing our understanding of atmospheric processes and assessing the impact of human activities on these processes. While issues such as the ozone hole and rising levels of greenhouse gases have received major attention. relatively little is known about the types, concentrations, sources, and sinks of hydrocarbons in the troposphere and stratosphere. Such information would be of tremendous utility in assessing the roles of various anthropogenic and biogenic processes on global carbon cycles. An ion trap mass spectrometer has been developed for monitoring trace levels of hydrocarbons in the atmosphere on NASA's DC-8 "flying laboratory". This aircraft is used to provide measurements in support of a number of "Mission to Planet Earth" activities and tropospheric chemistry experiments. In past missions, specific compounds have been monitored via highly specialized instrumentation, fast GO, or collection of whole air samples for subsequent ground-based analysis. The ion trap has several features. including small size. excellent sensitivity, and broad applicability, which make it highly atttrat:ive for atmospheric monitoring. The design of this instrument, its air sampling interface. and the various complications associated with aircraft-deployment will be described. Data showing the sensitivity of the instrument for detecting hydrocarbons at mixing ratios below one part-per-billion, and the use of MS/MS for direct, on-line, real-time monitoring will be presented.

Palmer, P. T.↗