Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HIP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

A comparison of plastic and visco-plastic constitutive models for accurate predictions in PM-HIP

Powder metallurgy hot isostatic pressing (PM-HIP) is an advanced manufacturing process that can efficiently produce near net shape parts with high material utilization and uniform microstructures. While the PM-HIP process is used frequently to produce small-scale components, its application to large-scale components is still limited due to inadequate understanding of its complex processes that cause unpredictable post-HIP shape distortions. A computational model can be a cost-effective alternative to exhaustive experimentation required to understand the PM-HIP process fully. Therefore, we present a comparison of plastic and visco-plastic models that are frequently used to model the PM-HIP process. We show that the predictions of powder densification behavior and shape distortions obtained from both the models are similar under most conditions and agree well with experimental observations.

Sarkar, Subrato [ORNL]↗

Preliminary results for HIP bonding Ta to W targets for the materials test station

Tungsten targets for the Materials Test Station (MTS) were clad with thin tantalum cover plates and a tantalum frame using hot isostatic pressing (HIP). A preliminary HIP parameter study showed good bonding and intimate mechanical contact for Ta cover plate thicknesses of 0.25 mm (0.010 inch) and 0.38 mm (0.015 inch). HIP temperatures of full HIP runs were 1500 C (2732 F). HIP pressure was 203 MPa (30 ksi).

36 MATERIALS SCIENCE↗

Experiment design for the neutron irradiation of $\mathrm{PM-HIP}$ alloys for nuclear reactors

Here, this article describes the design of an Advanced Test Reactor (ATR) drop-in neutron irradiation experiment aiming to directly compare the performance of nuclear structural alloys fabricated by powder metallurgy with hot isostatic pressing (PM-HIP) against conventional casting or forging. There is growing interest in PM-HIP alloys for nuclear applications because of their microstructural uniformity, superior mechanical properties, and reduced dependence on welding and machining, compared to cast/forged alloys. Nuclear code-qualification of PM-HIP alloys requires neutron irradiation testing to demonstrate performance under relevant conditions. In this experiment, six nuclear structural alloys were irradiated: Ni-based alloys 625 and 690, Grade 91 ferritic steel, SA508 pressure vessel steel, and 304L and 316L austenitic stainless steels. The experiment is assembled into seven capsules in four test trains and irradiated in three ATR inboard A positions. Both the PM-HIP and cast/forged versions of each alloy were irradiated under nearly identical conditions for comparative purposes, to target doses of 1 ± 0.2 and 3 ± 0.2 dpa at temperatures of 300 ± 50 °C and 400 ± 50 °C. A thorough description of the experiment design and thermal, structural and neutronic analyses performed to ensure the targeted irradiation conditions are met is provided. Specimens were configured as small disks, compact tension specimens and tensile bars to facilitate post-irradiation examination (PIE) that will include mechanical testing, microstructure characterization, and fracture toughness testing. Given the considerations for ASTM standardized mechanical testing, comparative fluence and temperature across specimen pairs, and comprehensive PIE planning herein, this work serves as a template for future nuclear materials qualification experiment designs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Low Cost HIP Fabrication of Advanced Power Cycle Components and PM/Wrought Inconel 740H Weld Development (Final Technical Report)

The objective of this Phase 1 project is to demonstrate the feasibility of structures and components for advanced fossil energy power cycle by fusion welding powder metallurgy (PM) based near net shape (NNS) hot isostatic pressing (HIP) Nickel superalloy Inconel 740H (IN740H) components to wrought IN740H components. The outcome of the project includes a prototype pipe elbow demonstration of the NNS HIP process using IN740H powder, an initial assessment of IN740H PM/wrought weldability, and a manufacturing and capital cost analysis of IN740H NNS HIP components for advanced ultra-super critical steam (AUSC) power plants. The anticipated value proposition of NNS HIP manufacturing is ~50% cost reduction of large complex components in AUSC or super-critical carbon dioxide (sCO2) power cycles. This document is a final technical report for the project, covering efforts conducted from October 2019 to June 2021.

20 FOSSIL-FUELED POWER PLANTS↗

Atomistic simulations to reveal HIP-bonding mechanisms of Al6061/Al6061

Molecular dynamics simulations were employed to understand the diffusion bonding process during hot isostatic pressing (HIP) of Al6061/Al6061 alloy. Simulations of the HIP process reveal atomistic phenomena that are difficult or unlikely to be observed experimentally and provide useful insights into the mechanism of diffusion and bonding. Here, the results reveal that at the start of the HIP process, a massive incursion of oxygen atoms occurs from the pre-existing γ-Al 2 O 3 to the 6061 region across the interphase interface. These oxygen atoms interact with the enriched Mg atom layer present at the existing γ-Al 2 O 3 and 6061 matrix to form a secondary complex Mg 2 Al 2 O 5 phase. Diffusion calculations also show that transport of atoms due to the applied pressure is 4–5 orders of magnitude higher than would occur in the absence of HIP conditions. The Mg 2 Al 2 O 5 phase also provides efficient pathways for the rapid transport of Mg atoms. Because of the higher diffusion coefficients observed for Mg within the phase, Mg atoms can move more swiftly compared to their diffusion within other phases such as γ-Al 2 O 3 . This accelerated mobility facilitates the rapid movement of Mg atoms across the interface, leading to changes in the local composition and the potential growth of the Mg 2 Al 2 O 5 phase.

36 MATERIALS SCIENCE↗

Experimental and Monte Carlo evaluation of Eclipse treatment planning system for effects on dose distribution of the hip prostheses

The present study aimed to investigate the effects of titanium, titanium alloy, and stainless steel hip prostheses on dose distribution based on the Monte Carlo simulation method, as well as the accuracy of the Eclipse treatment planning system (TPS) at 6 and 18 MV photon energies. In the present study the pencil beam convolution (PBC) method implemented in the Eclipse TPS was compared to the Monte Carlo method and ionization chamber measurements. The present findings show that if high-Z material is used in prosthesis, large dose changes can occur due to scattering. The variance in dose observed in the present study was dependent on material type, density, and atomic number, as well as photon energy; as photon energy increased back scattering decreased. The dose perturbation effect of hip prostheses was significant and could not be predicted accurately by the PBC method for hip prostheses. The findings show that for accurate dose calculation the Monte Carlo-based TPS should be used in patients with hip prostheses.

61 RADIATION PROTECTION AND DOSIMETRY↗

THE NATURE OF THE HYPER-RUNAWAY CANDIDATE HIP 60350

Young, massive stars in the Galactic halo are widely supposed to be the result of an ejection event from the Galactic disk forcing some stars to leave their place of birth as so-called runaway stars. Here, we present a detailed spectroscopic and kinematic analysis of the runaway B star HIP 60350 to determine which runaway scenario-a supernova explosion disrupting a binary system or dynamical interaction in star clusters-may be responsible for HIP 60350's peculiar orbit. Based on a non-local thermodynamic equilibrium approach, a high-resolution optical echelle spectrum was examined to revise spectroscopic quantities and for the first time to perform a differential chemical abundance analysis with respect to the B-type star 18 Peg. The results together with proper motions from the Hipparcos Catalog further allowed the three-dimensional kinematics of the star to be studied numerically. The abundances derived for HIP 60350 are consistent with a slightly supersolar metallicity agreeing with the kinematically predicted place of birth {approx}6 kpc away from the Galactic center. However, they do not exclude the possibility of an alpha-enhanced abundance pattern expected in the case of the supernova scenario. Its outstanding high Galactic rest-frame velocity of 530 +- 35 km s{sup -1} is a consequence of ejection in the direction of Galactic rotation and slightly exceeds the local Galactic escape velocity in a standard Galactic potential. Hence, HIP 60350 may be unbound to the Galaxy.

79 ASTRONOMY AND ASTROPHYSICS↗

Hiding-in-Plain-Sight (HiPS) Attack on CLIP for Targetted Object Removal from Images

Machine learning models are known to be vulnerable to adversarial attacks, but prior works have mostly focused on single-modalities. With the rise of large multi-modal models (LMMs) like CLIP, which combine vision and language capabilities, new vulnerabilities have emerged. However, these multimodal targeted attacks aim to completely change the model's output to what the adversary wants. In many realistic scenarios, an adversary might seek to make only subtle modifications to the output, so that the changes go unnoticed by downstream models or even by humans. We introduce Hiding-in-Plain-Sight (HiPS) attacks, a novel class of adversarial attacks that subtly modifies model predictions by selectively concealing target object(s), as if the target object was absent from the scene. We propose two HiPS attack variants, HiPS-cls and HiPS-cap, and demonstrate their effectiveness in transferring to downstream image captioning models, such as CLIP-Cap, for targeted object removal from image captions.

Daw, Arka [ORNL] (ORCID:0009000633191271)↗

A comparative study on the physicochemical characteristics of nanoparticles released in vivo from CoCrMo tapers and cement–stem interfaces of total hip replacements

The good biocompatibility and corrosion resistance of the bulk CoCrMo alloy has resulted in it being used in the manufacture of implants and load bearing medical devices. These devices, however, can release wear and corrosion products which differ from the composition of the bulk CoCrMo alloy. The physicochemical characteristics of the particles and the associated in vivo reactivity are dictated by the wear mechanisms and electrochemical conditions at the sites of material loss. Debris released from CoCrMo hip bearings, taper junctions, or cement–stem interfaces can, therefore, have different chemical and morphological characteristics, which provide them with different in vivo toxicities. Here, we propose to assess and compare the characteristics of the particles released in vivo from CoCrMo tapers and cement–stem interfaces which have received less attention compared to debris originating from the hip bearings. The study uses state–of–art characterization techniques to provide a detailed understanding of the size, morphology, composition, and chemistry of the particles liberated from the wear and corrosion flakes from revised hip replacements, with an enzymatic treatment. The phase analyses identified Cr 2 O 3 nanoparticles released from tapers and cement–stem interfaces, whose composition did not vary with origin or particle morphology. The size distributions showed significantly smaller particles were released from the stems, compared to the particles originating from the corresponding tapers. Furthermore, the investigation demonstrates that the tribocorrosive processes occurring at the taper and stem interfaces both result in Cr 2 O 3 nanoparticle formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Consolidation of iodine-loaded Ag 0 -functionalized silica aerogel with HUP, HIP and SPS

The U.S. Department of Energy is currently investigating alternative sorbents for the removal and immobilization of radioiodine from the gas streams in a nuclear fuel reprocessing plant. One of these new sorbents, silver-functionalized silica aerogel (Ag 0 -aerogel), shows promise as a potential replacement for silver mordenite because of its high selectivity and sorption capacity for iodine. Moreover, a feasible consolidation of iodine-loaded Ag 0 -aerogel to a durable SiO 2 -based waste form makes this aerogel an attractive choice for sequestering radioiodine. The main purpose of the study reported here was to investigate consolidation of Ag 0 -aerogel powders with or without iodine and with or without sintering additives with hot uniaxial pressing (HUP), HIP, and SPS. The selected densified samples were analyzed with a helium gas pycnometer for apparent density, with the Archimedes method for open porosity and apparent density, with scanning electron microscopy and energy dispersive spectroscopy (SEM-EDS) for the extent of densification, macro- and microstructural changes, and distribution of individual elements, and with X-ray diffraction (XRD) for crystalline phases. To convert the iodine-loaded Ag 0 -silica aerogel to a waste form, rapid consolidation with HUP, HIP, and SPS at moderate temperatures and pressures yields a final waste form consisting of AgI particles encapsulated in fused silica. HUP-processing (1200°C for 30 min under 29 MPa pressure) of Ag 0 -aerogel loaded with 20.2 mass% of iodine provided a product with residual open porosity of 16.9%. However, ~93% of sorbed iodine was retained in the sintered material. Densification with HIP at 1200°C for 30 min under 207 MPa pressure resulted in a fully dense silica-based waste form of 3.3 $\times$ 10 3 kg/m 3 bulk density containing ~22 mass% of iodine. Iodine was retained in the form of nano- and micro-inclusions of AgI dispersed in the silica matrix. Additives were not needed to enhance sintering process as depicted from the lack of open porosity and 100% retention of iodine in the consolidated product. The future tests will tell whether additives such as raw silica aerogel or Ag 0 -aerogel are required for HIPing to produce a fully dense waste form from iodine-loaded Ag 0 -aerogel containing higher concentrations of captured iodine. SPS-processing of samples with or without iodine revealed a benefit of additive-enhanced sintering. The samples containing additives (raw silica aerogel, colloidal silica, and Ag 0 -aerogel) shrunk faster and at lower temperatures. In addition, additives significantly improved distribution of silver compounds in the fully densified products, considerably decreasing the number of micron-sized inclusions of AgI, Ag and Ag 2 S at the grain boundaries.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Near-Net-Shape HIP Manufacturing for sCO2 Turbomachinery Cost Reduction

sCO2 turbomachinery that operates above 650°C requires the use of γ' strengthened Ni-based superalloys, leading to high cost and barrier of market adoption. Near-net-shape (NNS) HIP manufacturing with 282® alloy powder is being developed for sCO2 turbine components, with a significant estimated cost reduction. Tensile, creep, low cycle fatigue properties of argon gas atomized and plasma atomized powders were evaluated and compared to sand cast HAYNES® 282®. While tensile strength and fatigue life outperformed sand cast material, a 10~25% debit in the creep stress capability was observed due to the fine grain size and presence of prior particle boundaries (PPBs). Finite element model calibrated by powder rheological properties accurately predicted the nonuniform shrinkage during HIP, providing HIP tooling design to achieve the target dimension. A 20 lbs. turbine nozzle ring was successfully demonstrated within 0.01 inch dimensional tolerance at the vanes. A 1700lbs. turbine casing with complex internal struts and manifolds was also demonstrated being close to the target dimension.

14 SOLAR ENERGY↗

Perioperative Timing of Infliximab and the Risk of Serious Infection After Elective Hip and Knee Arthroplasty

Objective The optimal timing of tumor necrosis factor antagonists before elective surgery is unknown. This study evaluated the association between infliximab timing and serious infection after elective hip or knee arthroplasty. Methods A retrospective cohort study evaluated US Medicare patients with rheumatoid arthritis, inflammatory bowel disease, psoriasis, psoriatic arthritis, or ankylosing spondylitis who received infliximab within 6 months of elective knee or hip arthroplasty from 2007 to 2013. Propensity‐adjusted analyses examined whether infliximab stop timing (time between the most recent infusion and surgery) was associated with hospitalized infection within 30 days or prosthetic joint infection ( PJI ) within 1 year. Results Hospitalized infection within 30 days occurred after 270 of 4,288 surgeries (6.3%). Infliximab stop timing <4 weeks versus 8–12 weeks was not associated with an increase in infection within 30 days (propensity‐adjusted odds ratio [ OR ] 0.90 [95% confidence interval (95% CI ) 0.60–1.34]). The rate of PJI was 2.9 per 100 person‐years and was not increased in patients with stop timing <4 weeks versus 8–12 weeks (hazard ratio [ HR ] 0.98 [95% CI 0.52–1.87]). Glucocorticoid dosage >10 mg/day was associated with increased risk of 30‐day infection ( OR 2.11 [95% CI 1.30–3.40]) and PJI ( HR 2.70 [95% CI 1.30–5.60]). Other risk factors for infection included elderly age, comorbidities, revision surgery, and previous hospitalized infection. Conclusion Administering infliximab within 4 weeks of elective knee or hip arthroplasty was not associated with a higher risk of short‐ or long‐term serious infection compared to withholding infliximab for longer time periods. Glucocorticoid use, especially >10 mg/day, was associated with an increased infection risk.

George, Michael D.↗

Microstructure characteristics of LPBF&HIP fabricated graded composite transition joint between ferritic steel and austenitic stainless steel

Graded composite transition joints (GCTJs) offer a promising alternative to conventional dissimilar metal welds (DMWs) by enabling smooth compositional and microstructural transitions. However, GCTJs fabricated solely through additive manufacturing (AM) face challenges such as heat accumulation, complex parameter control, and elemental segregation. In this study, we propose a novel approach that relies on AM to design a spatially graded structure in one alloy and then employs hot isostatic pressing (HIP) as a diffusion bonding method to join it with a second alloy. Here, this method combines the flexibility of AM with the powder net-shaping advantage of HIP. Specifically, a series of closely packed austenitic stainless steel 304 conical structures were printed using laser powder bed fusion (LPBF) and then combined with ferritic steel P91 powder via HIP. By using electron backscatter diffraction (EBSD), electron probe microanalysis (EPMA), and transmission electron microscopy (TEM) techniques, the microstructure characteristics of the GCTJ of 304&P91, especially the interdiffusion zone (IDZ), have been systematically investigated. The microstructure at the interface transitions from austenite-ferrite (A+F) to austenite-martensite-ferrite (A+M+F), and finally to martensite-ferrite (M+F) due to diffusion. Additionally, the diffusion width between 304 and P91 increases with the volume fraction of P91. This unique design also ensures a gradual transition in both hardness and thermal expansion coefficient from 304 to P91, thereby enabling a smooth gradient in functional properties. Overall, this study proposes a novel approach for fabricating GCTJs and contributes to advancing design concepts in the field of dissimilar metal joining.

Additively manufacturing (AM)↗

Enhancing the tensile properties of EBM as-built thin parts: Effect of HIP and chemical etching

Highlights: • The EBM process leads to important cross section variations in thin parts. • Stress calculation must be based on the average section in order to be relevant. • As-built state has a detrimental effect on every mechanical property. • Mechanical properties of machined samples are met with chemical etching. • HIP has a beneficial effect on the ductility. - Abstract: As-built Ti-6Al-4 V thin parts were manufactured using Electron Beam Melting (EBM) and characterized by optical microscopy and laboratory X-ray tomography in order to observe their microstructure, pore distribution and surface aspect. Chemical etching and HIP post-treatments were applied to as-built samples and their effect on the material and static mechanical properties were studied. Tensile tests were performed on both as-built and post-treated samples and their results compared to the ones reported in the literature for machined EBM samples. Because of the significant variations of the cross section observed along the gauge length, the calculation of the tensile stresses is not straightforward. Three simple sections were measured from the tomography scans. The average section along the gauge length was considered as the most suitable. The tensile mechanical properties of the as-built samples were studied and a detrimental effect of the surface state on the yield strength, ultimate tensile strength and elongation to failure was observed. Smoothing of the surface irregularities induced by chemical etching provoked an increase of those mechanical properties whereas the change of the microstructure generated by the HIP treatment leads to a decrease of the material strength that goes along with an increase of the ductility. Down scaling factors were proposed in order to take into account the sample state, as-built or post-treated.

36 MATERIALS SCIENCE↗

Intensity-Modulated Radiation Therapy with Noncoplanar Beams for Treatment of Prostate Cancer in Patients with Bilateral Hip Prosthesis-A Case Study

Megavoltage photon intensity-modulated radiation therapy (IMRT) is typically used in the treatment of prostate cancer at our institution. Approximately 1% to 2% of patients with prostate cancer have hip prostheses. The presence of the prosthesis usually complicates the planning process because of dose perturbation around the prosthesis, radiation attenuation through the prosthesis, and the introduction of computed tomography artifacts in the planning volume. In addition, hip prostheses are typically made of materials of high atomic number, which add uncertainty to the dosimetry of the prostate and critical organs in the planning volume. When the prosthesis is bilateral, treatment planning is further complicated because only a limited number of beam angles can be used to avoid the prostheses. In this case study, we will report the observed advantages of using noncoplanar beams in the delivery of IMRT to a prostate cancer patient with bilateral hip prostheses. The treatment was planned for 75.6 Gy using a 7-field coplanar approach and a noncoplanar arrangement, with all fields avoiding entrance though the prostheses. Our results indicate that, compared with the coplanar plan, the noncoplanar plan delivers the prescribed dose to the target with a slightly better conformality and sparing of rectal tissue versus the coplanar plan.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Coplanar intensity-modulated radiotherapy class solution for patients with prostate cancer with bilateral hip prostheses with and without nodal involvement

Dose distributions for prostate radiotherapy are difficult to predict in patients with bilateral hip prostheses in situ, due to image distortions and difficulty in dose calculation. The feasibility of delivering curative doses to prostate using intensity-modulated radiotherapy (IMRT) in patients with bilateral hip prostheses was evaluated. Planning target volumes for prostate only (PTV1) and pelvic nodes (PTV2) were generated from data on 5 patients. PTV1 and PTV2 dose prescriptions were 70 Gy and 60 Gy, respectively, in 35 fractions, and an additional nodal boost of 65 Gy was added for 1 plan. Rectum, bladder, and bowel were also delineated. Beam angles and segments were chosen to best avoid entering through the prostheses. Dose-volume data were assessed with respect to clinical objectives. The plans achieved the required prescription doses to the PTVs. Five-field IMRT plans were adequate for patients with relatively small prostheses (head volumes<60 cm{sup 3}) but 7-field plans were required for patients with larger prostheses. Bowel and bladder doses were clinically acceptable for all patients. Rectal doses were deemed clinically acceptable, although the V{sub 50} {sub Gy} objective was not met for 4/5 patients. We describe an IMRT solution for patients with bilateral hip prostheses of varying size and shape, requiring either localized or whole pelvic radiotherapy for prostate cancer.

61 RADIATION PROTECTION AND DOSIMETRY↗

Correlation between Interface Microstructure and Bond Strength of Al6061/Al6061 HIP-Bonded Plates for Fuel Cladding Application

The effects of hot isostatic pressing (HIP) processing parameters on microstructure and bond strength of Al6061/Al6061 plate interfaces were systemically investigated at the micro- and nanoscale. The HIP bonding of the two aluminum plates was performed at four temperatures: 350°C, 400°C, 450°C, and 560°C. The results reveal the formation of micron scaled Mg 2 Si precipitate and uniform nano scaled Mg 2 Al 2 O 5 oxide at the interface. The formation of Mg 2 Al 2 O 5 is closely associated with the fast bulk diffusion of Mg from the Al matrix to the amorphous Al 2 O 3 /Al interface and subsequent reaction between Mg and Al 2 O 3 . Finally, the highest and lowest bond strengths were observed in samples HIP bonded at 450°C and 350°C, respectively.

36 MATERIALS SCIENCE↗

CHARACTERIZING K2 PLANET DISCOVERIES: A SUPER-EARTH TRANSITING THE BRIGHT K DWARF HIP 116454

We report the first planet discovery from the two-wheeled Kepler (K2) mission: HIP 116454 b. The host star HIP 116454 is a bright (V = 10.1, K = 8.0) K1 dwarf with high proper motion and a parallax-based distance of 55.2 ± 5.4 pc. Based on high-resolution optical spectroscopy, we find that the host star is metal-poor with [Fe/H] =–0.16 ± 0.08 and has a radius R {sub *} = 0.716 ± 0.024 R {sub ☉} and mass M {sub *} = 0.775 ± 0.027 M {sub ☉}. The star was observed by the Kepler spacecraft during its Two-Wheeled Concept Engineering Test in 2014 February. During the 9 days of observations, K2 observed a single transit event. Using a new K2 photometric analysis technique, we are able to correct small telescope drifts and recover the observed transit at high confidence, corresponding to a planetary radius of R{sub p} = 2.53 ± 0.18 R {sub ⊕}. Radial velocity observations with the HARPS-N spectrograph reveal a 11.82 ± 1.33 M {sub ⊕} planet in a 9.1 day orbit, consistent with the transit depth, duration, and ephemeris. Follow-up photometric measurements from the MOST satellite confirm the transit observed in the K2 photometry and provide a refined ephemeris, making HIP 116454 b amenable for future follow-up observations of this latest addition to the growing population of transiting super-Earths around nearby, bright stars.

79 ASTRONOMY AND ASTROPHYSICS↗