Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HEAT TREATMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effect of post-deposition heat treatment on microstructure and mechanical properties of NASA HR-1 cold spray coatings

The primary goal of this work was to examine the impact of heat treatment on the evolution of microstructure and mechanical properties of NASA HR-1 cold spray coatings. Coatings were produced employing a high pressure cold spray system using N2 and He process gases and the effect of process gas and deposition temperature on the microstructure and mechanical properties of the coatings was examined. Microstructural characterization was performed using optical microscopy, scanning electron microscopy, micro X-ray computed tomography, and electron backscatter diffraction. NASA HR-1 coatings produced with He process gas exhibited improved plastic deformation and resulted in the lowest porosity compared to those deposited with N2 process gas. All coatings showed brittle failure with limited ductility in the as-deposited condition. Heat treatment of the NASA HR-1 cold spray coatings was performed at 550°C and 950°C for 1 h to improve the mechanical strength of the coatings. Heat treatment improved the particle bonding and enhanced the mechanical properties of the cold spray coatings. Heat treatment performed at 550°C resulted in higher mechanical strength of coatings, whereas the heat treatment performed at 950°C resulted in recrystallized microstructure and improved ductility of the coatings. However, heat treatment at 950°C resulted in forming the Eta (η) phase and Ni-Ti intermetallics in all the NASA HR-1 cold spray coatings. Here, the overall results suggest that using He as process gas contributed to reduced porosity and enhanced mechanical properties of the cold spray coatings.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS1992

Effect of heat treatment on stiffness and damping of Sic/Ti-15-3

The effect of heat treatment on material properties of Sic/Ti-15-3 was measured by vibration tests. Heat treatment changes the microstructure, which stiffens the matrix and reduces its damping capacity. Test results illustrate how the changes in matrix material affect the stiffness and damping properties of the composite. Damping was found to be more sensitive than stiffness to microstructural changes in the matrix. Effects of heat treatment temperature and exposure time are presented.

Grady, Joseph E.↗
DOE OSTI2022

Predictive Tools for Customizing Heat Treatment of Additively Manufactured Aerospace Components

Laser-bed powder fusion (LBPF) additive manufacturing is increasingly being used to produce components of complex geometries using the Ni-base superalloy Inconel 718. The composition and the microstructure of the alloy are currently well optimized for wrought components made using conventional manufacturing processes such as rolling, forging, extrusion, etc. The attractive mechanical properties of the alloy result from the underlying austenitic matrix with fine equiaxed grains, and a high density and uniform distribution of the precipitation hardening phase, γ". Heat treatment steps such as homogenization, solutioning and aging are well documented for the wrought alloy. However, when the same wrought alloy compositions are used for the additive manufacturing (AM) processes, the asprocessed microstructure is significantly different, because of the different thermal history associated with LBPF, including rapid solidification and multiple temperature excursions that lead to multiple re-melting and reheating in the solid state. Rapid solidification introduces potential non-equilibrium effects at the moving solid-liquid interfaces that impact the extent of solute segregation, as well as the morphology of the dendritic grains that form. In order to recover the target mechanical properties, AM components have to undergo post-process heat treatments. However, such heat treatments have to be custom designed for the AM process and the component geometry because of the expected vast differences in the microstructure at various locations of a component with complex geometry. The homogenization and precipitation steps should be optimized for the component so that target mechanical properties can be obtained throughout the part. The objective of this research is to utilize High Performance Computing in phase field simulations of microstructure evolution during post-processing of AM components. The physics-based modeling will be beneficial in reducing the experimental effort required for heat treatment process selection, optimization, and certification, thus leading to a significant reduction in energy consumption for AM and post-processing heat treatment. The optimization study will help identify heat treatments steps that are critical for development of a final desired microstructure with the minimum energy input. This combined with shortening of the production cycle (time-to-market) by reducing the number of failed parts (property targets), and reduction in the number of iterations for process optimization, will enable 30-40% savings in the energy costs. Phase field simulations of the degree of homogenization and the effect of local matrix composition on the nucleation and growth of competing precipitating phases were performed using the Microstructure Evolution Using Massively Parallel Phase Field Simulations code developed in-house at the Oak Ridge National Laboratory. The simulations were able to successfully capture the kinetics of nucleation and growth, and morphologies of various precipitating phases as a function of local matrix compositions and composition gradients characteristic of local microstructures arising from location-dependent variations in the thermal conditions. Future work will involve extending the simulations to a length scale consisting of multiple dendrites, so that the effect of homogenization on the coarsening of the dendrites can be simulated and used as an additional input to the optimization of the heat treatment process.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Time-Dependent 600 °C Post-Weld Heat Treatment Response of Laser-Wire-Directed Energy Deposited Austenitic Stainless Steel Claddings on Carbon Steel

Austenitic stainless steel overlay claddings are often used to protect nuclear reactor pressure vessels from corrosion. Arc welding processes are traditionally employed, which require a high heat input to bond the dissimilar metals, creating a large heat-affected zone and high residual stress that demands a lengthy stress-relieving post-weld heat treatment, up to 48 hours. High energy beam (e.g., laser, electron beam) directed energy deposition-based overlay cladding processes show promise for fabricating claddings with superior performance compared to arc welded ones because of their localized heat input; however, their necessity and time of post-weld heat treatment are currently unclear. In this research, we investigate the time dependence of a 600 C stress-relieving post-weld heat treatment of austenitic stainless steel clad on low carbon steel by laser-wire-directed energy deposition, comparing the microstructure and mechanical properties of the as-fabricated condition to 2-, 10-, and 48-hour heat treatment times. Diffusion simulations and microscopy show a gradual carburization of the stainless steel cladding and decarburization of the heat-affected zone/base metal. Nanoindentation testing shows up to a 1.8–2.69 embrittlement in the cladding and a 0.33 to 0.69 softening in the heat-affected zone after the 48-hour post-weld heat treatment. Tensile testing of the cladding composites reveals that increasing post-weld heat treatment time raises clad cracking susceptibility due to intergranular carbide formation and shows that laser-wire-directed energy deposition claddings may not require post-weld heat treatment.

Coating↗
NASA NTRSDate not supplied

The Influence of Heat Treatments on the Microstructure and Tensile Properties of Additively Manufactured Inconel 939

This study investigated the effect of heat treatment variations on the microstructure and tensile properties of laser powder bed fused Inconel 939 manufactured via laser powder bed fusion. Three different heat treatment schedules, all of which comprise stress relief, hot isostatic pressing, solution annealing, and aging, were followed, and resulting changes in microstructure were analyzed using scanning electron microscopy. Tensile tests were conducted on specimens subjected to different heat treatments to evaluate the mechanical properties at room temperature. Microstructural results showed that solution treatment at 1190 °C for 4 h led to better removal of dendritic microstructure, while second-step aging at 850 °C resulted in monomodal distribution of precipitates. However, the second-step aging temperatures from 750 to 800 °C resulted in bi-modal distribution. The optimal heat treatment schedule, which yielded a superior combination of strength and ductility, involved solution treatment at 1190 °C for 4 h and two-step aging at 1000 °C for 6 h and 800 °C for 4 h.

Laser powder bed fusion (L-PBF)↗
DOE OSTI2024

Effect of Heat Treatment on Microstructure and Mechanical Property of 316L Stainless Steel Produced by Laser Powder Bed Fusion

The advanced non-light water reactor designs (Gen IV reactors), including molten salt/ very high temperature/ sodium-cooled and lead-cooled fast reactors, typically operate at higher temperatures and more extreme radiation conditions than light water reactors. An intrinsic part of the deployment and progress of Gen IV reactor designs is selecting the most suitable structural material for a specific application. Additive manufacturing (AM), a fairly new process of making physical, three-dimensional objects from a computer design file, is going to completely change the way of design, build and certify nuclear systems. It offers a range of opportunities to produce complex geometries from existing materials, offers new routes for processing of previously difficult to process materials, allows for design of new high-performance materials, and finally facilitates hybridization of dissimilar materials. This emerging technology has successfully produced cars, wind turbine blade molds and even live cells. It could also open up big opportunities for the nuclear industry to quickly deploy technologies at a fraction of the cost. So far, AM techniques have been preliminarily applied in the field of nuclear reactors, including the classical parts such as the pressure vessel of a small reactor with 508-III steel, the bottom nozzle of a fuel assembly with 304L steel, the fuel cladding with zirconium alloy and the integrated impeller of a pump and the multi-channel valve body with 316L steel [6,7]. The AM applications for operating nuclear reactors started in auxiliary plant components and have slowly migrated to metallic reactors and core components, but many of these are not safety critical components. Although many parts used for nuclear reactors have been fabricated by AM techniques, practical applications in engineering are still a long way off due to the uncertainty factors focused on the processing, material properties, analysis methods and application standards, which feeds the safety and life-cycle of the nuclear reactor. Due to rapid, repeated heating and cooling during production, a high dislocation density was present in the AM material. This microstructure feature is unstable at elevated temperature while high temperature is one of the typical operation environments for nuclear reactors. Thus, it is important to understand the thermal effect on the microstructure of AM material. The objectives of this study are to investigate the effect of heat treatment on the microstructure and mechanical properties of 316L stainless steel produced by laser powder bed fusion additive manufacturing, and to determine an appropriate heat treatment practice that will be applied to the lightweight AM lattice-structured material with the same chemistry. The heat treatment study consisted of annealing the samples at a temperature range of 800 to 1200 oC with a 50 oC increment for different times (1-24 hours), followed by vacuum or air cooling. Microstructural characterization was carried out by Scanning Electron Microscope (SEM). Grain size and crystallographic orientation were investigated by Electron Backscatter Diffraction (EBSD). Vickers hardness tests with a 0.5 kg load were employed to determine the hardness of samples after different heat treatments. After heat treatment, the random crystallographic orientation was preserved, and the volume fraction of high-angle grain boundaries (grain boundary misorientation =15 oC) remained the same. The dislocation density decreased with annealing temperature due to recovery. The fine subgrain structures in the as-printed specimen were quite stable up to 1200 oC. Minimal recrystallization was observed up to 1200 oC. Recrystallization initiated only after 8.5 hours at 1200 oC. The SEM images did not show obvious dependence of microstructure on cooling rate. The hardness of the specimens decreased with increasing annealing temperature as a result of the decrease in dislocation density. It is interesting to note that the AM material showed very similar hardness to the wrought material when annealing at similar temperature, although the microstructures are very different. Annealing at 1050 oC for 1 hour followed by air cooling was selected as the heat treatment procedure for the lattice designed lightweight AM 316L material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of heat treatment on creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

The objective of this study is to understand the thermal stability of microstructure and its effect on the creep behavior of additively-manufactured 316L stainless steel (AM 316L SS). Creep specimens were fabricated from rods printed by a laser powder bed fusion process. Six different heat treatments, namely 650 °C/1 h, 700 °C/1 h, 750 °C/1 h, 800 °C/1 h, 900 °C/1 h and 1050 °C/1 h were applied to the creep specimens. The heat-treated specimens were creep-tested under the same condition, 550 °C/275 MPa to evaluate the effect of post-build heat treatment on the creep behavior of AM 316L SS. In the temperature range of 650-750 °C, dislocation density within cells, and cell size and wall thickness were affected by the heat treatment, while elemental segregation at boundaries remained unchanged and Mn-enriched Si oxide particles remained stable. In the temperature range of 750-900 °C, concurrent changes were observed in dislocation cell structures, elemental segregation and oxide particles. The 1050 °C-heat treatment removed cell structures and boundary solute segregations, leading to formation of equiaxed grains; Mn-enriched Si oxide particles in the as-built specimen were replaced by more stable Mn-enriched Cr oxides. The creep life of AM 316L SS increased after the heat treatment at 650 °C and then decreased with increasing temperature up to 900 °C where cell/subgrain structures still existed. The creep rate and creep elongation followed an opposite trend. The creep rate can be correlated with the structural parameters of cell/subgrain size and cell wall/boundary thickness and can be rationalized by different strengthening mechanisms of dislocation cells and subgrains. The heat treatment affected strongly the primary and secondary creep but had a minimal effect on the tertiary creep of AM 316L SS.

316L stainless steel↗
DOE OSTI2025

Synthesis and post-heating treatment of inorganic NaF·Na 3 SbS 4 solid electrolytes

Sulfide-type sodium (Na) solid electrolytes (SEs) with halide doping have attracted serious interest due to their high ionic conductivity and great potential in solid-state Na batteries. While other halogens such as Cl, Br, I have been studied to enhance Na-ion transport in sulfide-type SEs, the introduction of fluorine (F) is rarely investigated. Moreover, synthetic parameters such as heating treatment temperatures strongly influence the structure and conductive properties of halide-doped sulfide SEs. Herein, we prepared xNaF·(1-x)Na 3 SbS 4 nanocomposites with varying concentration of F using a low-temperature (150 °C) heating method, and studied the effects of post-heating treatment on structure and conductivity. In-situ neutron diffraction was employed to investigate the structural evolution of X-doped Na 3 SbS 4 (X = F, Cl) during the post-heating treatment and cooling process. In addition, the post-heating treatment at 300 °C leads to increased ionic conductivity of xNaF·(1-x)Na 3 SbS 4 nanocomposites with various F contents. After 300 °C post-heating treatment, 0.2NaF·0.8Na 3 SbS 4 exhibited the highest conductivity of 0.48 mS cm –1 at room temperature. Moreover, improved electrochemical stability was also observed in Na-Sn symmetric cells, specially, with prolonged stable cycling for 300 h and much lower polarization voltage (<0.35 V). Furthermore, this work highlights the importance of post-heating treatment on the structural evolution and its role in exploring new halide-incorporated sulfide-type SEs, promoting the development of inorganic solid-state ionic conductors.

25 ENERGY STORAGE↗
DOE OSTI2025

Single particle impact explorations on the role of powder heat treatments in cold spray: Effects of strength and oxide structure

In cold spray, the optimization of the powder feedstock for improving the final properties of the coating and for improving the process itself are two different objectives. This paper explores the latter, studying the relationship between powder pre-heat treatment and the kinetic bonding between the individual particles and the substrate. Using a laser-induced particle impact test (LIPIT), we investigate the effect of different heat treatments on the critical adhesion velocity of Al 6061. Although heat treatments change the strength of the powders as well as the thickness of the native oxide layer each by as much as ∼50 %, the critical adhesion velocity remains constant to within only ∼10 %. A deeper analysis reveals that these two factors change in somewhat complementary ways for the heat treatments explored here, leading to counteracting effects. By quantitatively evaluating these two microstructural factors in tandem, we find that they are roughly equally important in determining the critical adhesion velocity. These observations thus provide insight for the development of new heat treatment regimens that might lower the adhesion velocity.

Al 6061↗
DOE OSTI2025

Dynamic response of 17-4 stainless steel as a function of manufacturing method and heat treatment

We present a series of plate-impact experiments on 17-4 stainless steel to study the effect of manufacturing method and heat treatment on the Hugoniot elastic limit (HEL), Hugoniot, phase transformation stress, and spallation strength. Two traditional manufacturing methods were considered, wrought processing and casting, as well as two additive manufacturing methods, laser powder-bed fusion (LPBF) and wire-fed electron beam (EBAM). For both LPBF and EBAM 17-4 stainless steel variants, two billets were printed, enabling the application of two unique heat treatments. The HEL stress depended heavily on the thermal history, with the HEL increasing after the formation of Cu-rich precipitates via heat treatment. The Hugoniot response both below and above the phase transition was unaffected by the manufacturing method or heat treatment. The phase transition stress depended heavily on the thermal history, with its variation being attributed to the presence of various microstructural features. This is supported by a marked increase in the phase transition stress after precipitation hardening. These results suggest that the notion of the phase transition stress being dictated by bulk composition is an oversimplification and the stress fields generated by the meso-scale structure are a dominant force. The spallation strength was lower in the cast material compared to all other 17-4 stainless steel variants due to the presence of brittle δ-ferrite inclusions. Additionally, a drop in the tensile strain-rate was observed in the spallation response above the phase transition stress, which was hypothesized to stem from the kinetics of the reversion to the low-pressure phase during spall.

Compressive stress↗
DOE OSTI2024

Peak microhardness recovery via T6 heat treatment with extremely soft annealed Al7075 feedstock in additive friction stir deposition

With standard T6 heat treatments, precipitate-hardened alloys such as Al7075 and Al6061 fabricated using Additive Friction Stir Deposition (AFSD) method restore to noticeablely different peak mechanical properties. Previous research observed similar results but did not provide a viable solution. This study proposes a new processing strategy, namely enhanced plastic deformation by subjecting the Al7075 feedstock to annealed softening treatments. Specifically, by annealing the standard T651-Al7075 feedstock and deposition substrate (179 HV), their Microhardness were first degraded to its lowest state (80 HV), which is called a Soft-to-Soft system. For the Soft-to-Soft system subjected to AFSD, after undergoing appropriate T6 heat treatment, the microhardness of the AFSD 7075 alloy was restored to its peak value (183.1 ± 1.8 HV). The results indicate that this softening strategy can effectively reduce the non-strengthening phase in the AFSD matrix, thereby increasing the strengthening phase (η′ phase). This addresses the issue of traditional AFSD-prepared aluminum alloys being unable to achieve peak performance through T6 heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effects of heat treatment on the response of WE43 Mg alloy: crystal plasticity finite element simulation and SEM-DIC experiment

The present report addressed the effects of heat treatment on the mechanical response of a WE43 Mg alloy using an integrated framework of SEM-DIC experiment and CPFE simulation. Both macroscopic responses including yield strength, ultimate strength, ductility, and microscopic responses, including local displacement and strain maps, were experimentally investigated. The focus of this work is to use the CPFE simulation as an integrated computational tool to study the effects of heat treatment. The CPFE framework was evaluated using the local fields of displacement and strain obtained from the SEM-DIC experiment rather than the conventional scheme of using macroscopic responses at different loading directions. Subsequently, the information which is available using CPFE, such as the critical resolved shear stress (CRSS) and relative slip activity, was used to study the effects of heat treatment on the response of WE43 Mg alloy. The contributions of different strengthening mechanisms on the CRSS were addressed. The results show that effects of heat treatment can be captured using the predominant mechanisms of the grain size effect and the influence of precipitates. Finally, it has been shown that classical Hall-Petch in which one constant can capture the size effects, should be modified. To do so, each deformation mode should have a unique Hall-Petch constant, which are calculated here for the WE43 Mg alloy.

36 MATERIALS SCIENCE↗
NASA NTRS2001

The Tensile Properties of Advanced Nickel-Base Disk Superalloys During Quenching Heat Treatments

There is a need to increase the temperature capabilities of superalloy turbine disks. This would allow full utilization of higher temperature combustor and airfoil concepts under development. One approach to meet this goal is to modify the processing and chemistry of advanced alloys, while preserving the ability to use rapid cooling supersolvus heat treatments to achieve coarse grain, fine gamma prime microstructures. An important step in this effort is to understand the key high temperature tensile properties of advanced alloys as they exist during supersolvus heat treatments. This could help in projecting cracking tendencies of disks during quenches from supersolvus heat treatments. The objective of this study was to examine the tensile properties of two advanced disk superalloys during simulated quenching heat treatments. Specimens were cooled from the solution heat treatment temperatures at controlled rates, interrupted, and immediately tensile tested at various temperatures. The responses and failure modes were compared and related to the quench cracking tendencies of disk forgings.

Gabb, Timothy P.↗
DOE OSTI2025

Effect of Carbon Support Heat Treatment on the Performance of Ion-Pair High-Temperature PEM Fuel Cells

Heat treatment can significantly alter the physical and chemical properties of carbon supports, thereby influencing the performance of proton exchange membrane (PEM) fuel cells. This study explores how varying carbon heat treatment temperatures—from 1,000 °C to 2,200 °C—affect the structure and performance of platinum-based catalysts in high-temperature PEM fuel cells. Increasing the heat treatment temperature led to a notable decrease in surface area, along with increases in carbon grain size and hydrophobicity. Although the catalyst supported on carbon treated at 1,000 °C exhibited the highest catalyst activity, the MEA using carbon treated at 1,500 °C delivered the best overall fuel cell performance. This is attributed to an optimized balance between hydrophobicity and accessible surface area, which enhances water management and catalyst utilization. These findings underscore the importance of carbon support engineering in improving the efficiency of ion-pair high-temperature PEM fuel cells.

08 HYDROGEN↗
NASA NTRSDate not supplied

Effect of Heat Treatments on the Tensile Properties of Additively Manufactured 15-5 Ph Stainless Steel

This study investigated the effect of post-manufacture heat treatments on the microstructure and mechanical properties of 15-5 PH stainless steel (SS) fabricated by laser powder-directed energy deposition (LP-DED). Various heat treatment procedures (CA-H900 and CA-H1150) were conducted to evaluate their effects on the tensile behavior of LP-DED 15-5 PH SS. Scanning electron microscopy was used to characterize the microstructural features and the fracture surfaces. Tensile tests were performed to evaluate the mechanical properties at cryogenic and room temperatures. Reduction in area of CA-H1150 treated specimens after tensile tests was significantly higher than CA-H900 ones, while the ultimate tensile and yield strengths of CA-H900 specimens were higher compared to the CA-H1150 ones. The mechanical behavior of the LP-DED 15-5 PH SS in various heat treatment conditions is discussed based on their microstructures and fracture surfaces.

Laser powder directed energy deposition (LP-DED)↗
DOE OSTI2023

Effect of heat treatment paths on the aging and rejuvenation of metallic glasses

Here, this study explores the influence of heat treatment paths on the structural relaxation of metallic glasses (MGs) in the regime of fast dynamics. We create MG samples using various quenching rates, from 10 9 to 10 11 K/s, and expose these samples to near-T g heat treatments with assorted combinations of heating/cooling rates, from 5×10 10 to 5×10 12 K/s, and annealing durations, from 10 ps to 10 ns. Results show that the effect of the heating rate is intricately tied to the initial structure of the MG, while a decrease in the cooling rate invariably intensifies the aging process. Extending the annealing duration may induce either aging or rejuvenation, subject to the specific thermal history. To interpret these findings, we hypothesize that the memory effect, governed by the activation and annihilation of reversible and irreversible flow units, underpins the rejuvenation-aging competition in MGs. Moreover, we suggest viewing the cooling stage as an annealing phase controlled by gradient temperature and fine-tuning its rate to achieve the targeted active flow unit distributions. This study illuminates the role of fast dynamics during the glass relaxation process and offers practical strategies for tailoring heat treatments to optimize MG structures and mechanical performance.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effects of magnetic field assisted heat treatment on the microstructure and mechanical properties of Fe-0.63 %C alloy

This study investigates the influence of an applied magnetic field on the microstructural evolution and mechanical properties of hypoeutectoid steels subjected to heat treatment. Tensile tests and microstructural analysis were performed on samples processed under varying magnetic field strengths (0 T, 5 T, and 9 T) and different austenitization incubation times. The results indicate that the application of a magnetic field alters the fraction of proeutectoid ferrite phase without changing the cooling rates and heat treatment process. Additionally, pearlite microstructural features such as lamellar spacing and misorientation angles exhibit variations under different field strengths. While the pearlite nodule diameter remains largely unaffected, an increase in percentage elongation and strength is observed in the 5 T treated sample, attributed to changes in microstructural features with the magnetic field. Additionally, the percentage elongation is reduced in the samples heat treated with reduced austenitization incubation times. The study further demonstrates that low-angle misorientations increased in the samples taken parallel to the magnetic field direction, influencing the mechanical response. These findings suggest that applying a magnetic field during heat treatment provides an additional driving force for phase transformations, offering a manufacturing process for tailoring microstructures and optimizing mechanical properties. Moreover, integrating magnetic fields in heat treatment processes has potential benefits in energy efficiency.

High magnetic field↗