Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite powder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Proposed Subcritical Assembly for Nuclear Criticality Safety Training at the Oak Ridge National Laboratory

The design of a new subcritical assembly at Oak Ridge National Laboratory (ORNL) has been finalized. This design takes the feasibility study of the subcritical assembly performed in August 2020 to an implementable design. This subcritical assembly will support the Nuclear Criticality Safety Program (NCSP) training and education program. The addition of this subcritical assembly into the NCSP training and education will enhance the program by providing backup capacity for training if nuclear facility operations are disrupted at Sandia National Laboratories or the National Criticality Experiments Research Center; providing a new location that is more accessible to students in the Eastern portion of the United States; providing flexibility to support students from a diverse background (e.g., university students, foreign nationals). The proposed subcritical assembly uses legacy AGN-201M research reactor fuel plates that are available at the Y-12 National Security Complex. The final design of this subcritical assembly contains approximately 617 grams of 235 U as UO 2 powder distributed homogeneously in polyethylene. The fuel plates will have a graphite neutron reflector to obtain a core multiplication, M, from 10 to 20, corresponding to a $k_{eff}$ of 0.90 to 0.95, respectively. The subcritical assembly will be able to support at least four experiments for the training courses: (1) the addition of fissile material to the core (mass), (2) a core separation experiment (interaction), (3) the addition of moderators to the core (moderation), and (4) the addition of neutron absorbers to the core (poison/absorption). The subcritical assembly will be designed to be inherently safe—subcritical under all normal and abnormal conditions— and will provide the capability to conduct hands-on training to support NCSP and general nuclear criticality safety staff training and qualification goals.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Graphite resistive heated diamond anvil cell for simultaneous high-pressure and high-temperature diffraction experiments

High-pressure and high-temperature experiments using a resistively heated diamond anvil cell have the advantage of heating samples homogeneously with precise temperature control. Here, we present the design and performance of a graphite resistive heated diamond anvil cell (GRHDAC) setup for powder and single-crystal x-ray diffraction experiments developed at the Extreme Conditions Beamline (P02.2) at PETRA III, Hamburg, Germany. In the GRHDAC, temperatures up to 2000 K can be generated at high pressures by placing it in a water-cooled vacuum chamber. Temperature estimates from thermocouple measurements are within +/–35 K at the sample position up to 800 K and within +90 K between 800 and 1400 K when using a standard seat combination of cBN and WC. Isothermal compression at high temperatures can be achieved by employing a remote membrane control system. Importantly, the advantage of the GRHDAC is demonstrated through the study of geophysical processes in the Earth’s crust and upper mantle region.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Solid Phase Processing of Lead-Free Brass with Carbon Additives

Currently, “lead-free” brass alloys (like C27450/C27451/C6930), used extensively in drinking water fixtures and automotive, electrical, and electronic applications contain maximum 0.25% lead to maintain mechanical performance and machinability. Adding graphite to brass as an alternative to lead, using casting, powder metallurgy, and extrusion methods, has been explored previously. However, all these methods have proven to be energy-, time-, and resource-intensive, while not enabling performance equivalent to that of C36000 brass. In this project, we developed a one-step approach using friction extrusion and ShAPE to make lead-free brass/graphite components such as wires, rods and tubes with mechanical performance equivalent to commercial lead-free brass alloys. Manufacturing temperatures were maintained ~550-730 °C with feed rates ranging between 4 – 25 mm/min. Results show larger grains at the center of the rods and wires with smaller grains developing at the edges. Graphite particles were sheared in the direction of extrusion with higher strains observed towards the edges. Hardness of the brass/graphite samples was over 25% higher than that of the corresponding brass-only samples (rods and wires), also friction extruded. Our results show that the sub-micron graphite plays an important role in limiting process temperature and restraining grain growth during friction extrusion, thus reducing grain size in composites.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Coal as Value-Added for Lithium Battery Anodes (Final Report)

Graphite is a basic material used for energy storage in lithium-ion (Li-ion) batteries. More than 70% of worldwide graphite production and nearly 50% of the annual graphite supply for the United States comes from China. Potential economic and national security concerns exist because Li-ion batteries are used not only for the fast-growing electrical vehicle market (15.6% compound annual growth rate [CAGR] from 2018 to 2028 in North America), but also for defense applications including unmanned aerial and ground vehicles. Development of an alternative formulation for Li-ion batteries is key. Building upon previous research confirming the ability of silicon alloys to improve the energy density of anodes, Semplastics developed a novel material based on our X-MAT® polymer-derived ceramic (PDC) technology. The X-MAT anode material is a composite of chemically tailored silicon oxycarbide (SiOC) and domestically sourced coal powder, designed to be a drop-in replacement for graphite within Li-ion battery anodes. Preliminary tests of this material showed more than twice the reversible capacity of graphite anodes (1,000 mAh/g vs. 372 mAh/g), with excellent stability and capacity retention, almost 100% coulombic efficiency, low voltage potential, and low thermal expansion. At full adoption in 2024, we expect the coal utilization to reach 27,300 tons. Through this project, Semplastics proposed to complete development and begin commercialization of this material. The objective was to determine the best formulation for technical performance and economic viability. At the end of the project, the X-MAT anode material is ready for implementation into existing battery manufacturing processes and can have a significant impact on the utilization of coal, with positive effects for the mining sector and the mitigation of carbon dioxide (CO 2 ) emissions.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Solid-state reaction mediated microstructural evolution in a spark plasma sintered in situ Ti–B 4 C composite

For this study, a novel porosity-free in situ Ti–B 4 C composite was fabricated via spark plasma sintering (SPS). Detailed analysis of the phase evolution, coupling results from XRM, XRD and SEM-EBSD-EDS, indicate that primarily TiB 2 precipitates formed due to the in-situ reactions between the boron-carbide and titanium powders. The precipitation of TiB 2 resulted in the formation of a graphitic C-rich thin layer circumscribing the partially reacted B 4 C particles. Further progression of the in-situ reaction leads to the out-diffusion of the excess carbon from the B 4 C particles, across the graphite and TiB 2 phases, forming TiC upon reacting with the titanium matrix. Therefore, the final microstructure primarily consisted of TiB 2 , TiC, and partially reacted B 4 C phases, with small amounts of TiB, α-Ti, and graphite. Furthermore, the microstructure in these SPS processed in situ composites appeared to be the product of a solid-state Ti–B 4 C diffusion couple, substantially different from their fusion-based additively manufactured counterparts. Nano-indentation tests revealed a remarkably high average hardness of ~25 GPa for this SPS-processed Ti–B 4 C composite and comparable (with literature) phase-specific hardness and modulus values for the constituent TiB 2 , TiC, and B 4 C phases.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanoscale insights into the structure of solution-processed graphene by x-ray scattering

Abstract Chemical exfoliation is an attractive approach for the synthesis of graphene due to its low cost and simplicity. However, challenges still remain in the characterization of solution-processed graphene, in particular with atomic resolution. Through this work we demonstrate the x-ray pair distribution function as a novel approach to study solution-processed graphene or other 2D materials with atomic resolution, directly in solution, produced by liquid-phase and electrochemical exfoliations. The results show the disappearance of long-range atomic correlations, in both cases, confirming the production of single and few-layer graphene. In addition, a considerable ring distortion has been observed as compared to graphite, irrespective of the solvent used: the normal surface angle to the sheet of the powder sample should be less than 6°, compatible with ripples formation observed in suspended graphene. We attribute this effect to the interaction of solvent molecules with the graphene nanosheets.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Screening of Lost Circulation Materials for Geothermal Applications: Experimental Study at High Temperature

Abstract This study presents a laboratory experimental research to determine the characteristics of lost circulation materials (LCMs) capable of addressing thermal degradation, providing bridging and sealing in geothermal conditions. Eleven different materials were tested: Walnut Fine, Walnut Medium, Sawdust, Altavert, Graphite Blend, Bentonite Chips, Micronized Cellulose (MICRO-C), Magma Fiber Fine, diatomaceous earth/amorphous silica powder (DEASP), Cotton Seed Hulls, and a Calcium Carbonate Blend. The filtration and sealing pressure of the LCMs were measured with HPHT equipment up to 149 °C (300 °F). Besides, the particle size distribution (PSD) of fine granular materials was measured. The results show that the performance of some LCM materials commonly used in geothermal operations is affected by high temperature. Characteristics such as shape and size made some materials more prone to thermal degradation. Also, it was found that the PSD of LCMs is a key factor in the effectiveness of bridging and sealing fractures. The results suggest that granular materials with a wide particle size distribution PSD are suitable for geothermal applications.

Energy & Fuels↗
DOE OSTI2025

Development and Validation of MALAMUTE model for Electric Field Assisted Sintering of Structural Materials

Fusion power plant designs feature extreme material performance requirements for structural material candidates. In addition to conventional alloys, more advanced composites and oxide dispersion strengthened (ODS) alloys are being explored, however, achieving the desired microstructures to maximize performance using traditional manufacturing methods can be challenging. The advanced manufacturing (AM) electric field-assisted sintering (EFAS) technique offers improved control over the final microstructure through higher heating and cooling rates and moderate pressures. Modeling and simulation tools show promise in elucidating the process-structure-property-performance (PSPP) correlation for AM-produced parts, including the EFAS process. An inherently multiscale process, the EFAS technique aligns well with the multiscale modeling capability of the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE)[cite]. We present here an electro-thermo-mechanical approach to modeling the EFAS process using the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) code. Prediction of the field and gradient distributions across the EFAS tooling is required to accurately describe the conditions for the lower-scale microstructural evolution models. In this work we present the MALAMUTE model developed to predict the electrical potential, temperature, and mechanical stress distribution across the EFAS graphite tooling and part at the larger engineering-scale. Validation of the MALAMUTE engineering-scale model is completed using data from experimental densification and pre-densified runs of iron powder via EFAS at 1000oC. These runs were conducted using a Thermal Technology DCS-5 EFAS system. Data collected during the experiment runs include the direct current (DC) supplied to the graphite tooling, the temperature of the graphite tooling as measured with a pyrometer, and the force applied to the top of the graphite tooling stack, and the data were recorded every 10 seconds. Our validation approach used the current and force data from the EFAS run as boundary condition inputs to the MAMALUTE simulation; the temperature data were used to evaluate the MALAMUTE EFAS model prediction. Results of the MALAMUTE simulations are employed to connect the external pyrometer temperature measurement to the temperature profile across the part undergoing consolidation. We investigate the impact of material property variation and mesh deformation on the temperature profile as predicted by MALAMUTE. We conclude by highlighting projects where the MALAMUTE EFAS modeling and simulation capabilities will be used to assist experimental design.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Structural Evolution and Transition Dynamics in Lithium Ion Battery under Fast Charging: An Operando Neutron Diffraction Investigation

Abstract Fast charging (<15 min) of lithium‐ion batteries (LIBs) for electrical vehicles (EVs) is widely seen as the key factor that will greatly stimulate the EV markets, and its realization is mainly hindered by the sluggish diffusion of Li + . To have a mechanistic understanding of Li + diffusion within LIBs, in this study, structural evolutions of electrodes for a Ni‐rich LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) || graphite cylindrical cell with high areal loading (2.78 mAh cm −2 ) are developed for operando neutron powder diffraction study at different charging rates. Via sequential Rietveld refinements, changes in structures of NMC622 and Li x C 6 are obtained during moderate and fast charging (from 0.27 C to 4.4 C). NMC622 exhibits the same structural evolution regardless of C‐rates. For phase transitions of Li x C 6 , the stage I (LiC 6 ) phase emerges earlier during the stepwise intercalation at a lower state of charge when charging rate is increased. It is also found that the stage II (LiC 12 ) → stage I (LiC 6 ) transition is the rate‐limiting step during fast charging. The LiC 12 → LiC 6 transition mechanism is further analyzed using the Johnson–Mehl–Avrami–Kolmogorov model. It is concluded as a diffusion‐controlled, 1D phase transition with decreasing nucleation kinetics under increasing chargingrates.

25 ENERGY STORAGE↗
DOE OSTI2023

$In-situ$ synchrotron x-ray diffraction and thermal expansion of TiB2 up to ~3050 °C

There is an increasing interest in understanding the performance and properties of ultra-high temperature ceramics due to their high melting points (<3000 °C) that make them promising for extreme environment applications. In-situ high temperature X-ray diffraction experiments were performed on TiB 2 beads up to ~3050 °C. For these experiments, TiB 2 powders were fabricated into spherical beads via gel casting methods and densified in a high temperature graphite furnace. These sample beads were then levitated in a conical nozzle levitator with reducing atmosphere (3% H 2 -Ar) while being heated using a 400 W CO 2 laser. During levitation a collimated synchrotron X-ray source was used to perform in-situ, temperature-dependent structural characterizations. The anisotropic coefficients of thermal expansion of TiB 2 were characterized as a function of temperature up to ~3050 °C. Elucidation of these properties are critical for the advancement of TiB 2 ceramics and other transition metal di-borides for use in high temperature applications such as hypersonic platforms, nuclear reactors, and atmospheric re-entry.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Developing a Facile Technology for Converting Domestic US Coal into High-Value Graphene

Universal Matter Ltd. was formed in July 2019 to scale-up and commercialize a breakthrough process, Flash Joule Heating (FJH), to transform different coal grades, into high-quality graphene. This graphene is made using a high-voltage electric discharge that brings the carbon source to temperatures higher than 3,000 K in less than 10 milliseconds. The short burst of electricity breaks all chemical bonds in the feedstock and reorders the carbon atoms into exceptionally thin layers of a special type of graphene, at an estimated $100 per ton in electricity cost. This process is capable of producing 1-5 layer-thick high-quality graphene (with defects of <0.05% and purity of >99%) in a green, practical, and cost-effective process. The graphene produced in the FJH process is a very special kind of graphene called “turbostratic graphene” (TG). TG offers superior physical properties compared to other graphene structures on a similar weight basis. Unlike graphene made from graphite using traditional techniques, the graphene layers in TG stack in an irregular pattern that allows the graphene powder to be exfoliated more easily and blend more evenly within other materials. The TG produced using our FJH technology is the most economical graphene product that opens up significant large volume markets for end-use applications; it would allow the use of TG made from coal for commercial applications in several market segments including energy storage, sensors, hyper-lubricants, reinforced plastics, and building materials such as concrete.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

Electrochemical carbon deposition from CO 2 in molten carbonates: substrate-dependent growth

Electrochemical carbon deposition from molten carbonate salts using inert electrodes and no additional catalyst is systematically examined. At sufficiently cathodic potentials, carbon formation occurs within 30 min and transitions from substrate-dependent nucleation to carbon-on-carbon growth. Although deposits formed on either mild-steel or graphite cathodes exhibit comparable thicknesses and salt contents, their macrostructures differ, reflecting differences in early-stage growth rates and surface chemistry. Characterization by ICP-OES, Raman spectroscopy, SEM/EDS, synchrotron powder X-ray diffraction, and C K-edge X-ray absorption near edge structure reveals that the as-deposited carbon is predominantly disordered sp 2 -bonded material. However, post-treatment reveals latent turbostratic ordering in select samples, indicating that short-range order is established during deposition but is obscured by an entrained electrolyte and kinetically formed amorphous phases. No anode-derived contamination is detected, and carbon grown on graphite cathodes shows minimal metallic impurities. These results clarify the role of cathode surface chemistry and provide pathways for controlling electrode-derived impurity incorporation and carbon structure in catalyst-free molten carbonate systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Additive manufacturing of complex objects using refractory matrix materials

A method for the manufacture of a three-dimensional object using a refractory matrix material is provided. The method includes the additive manufacture of a green body from a powder-based refractory matrix material followed by densification via chemical vapor infiltration (CVI). The refractory matrix material can be a refractory ceramic (e.g., silicon carbide, zirconium carbide, or graphite) or a refractory metal (e.g., molybdenum or tungsten). In one embodiment, the matrix material is deposited according to a binder-jet printing process to produce a green body having a complex geometry. The CVI process increases its density, provides a hermetic seal, and yields an object with mechanical integrity. The residual binder content dissociates and is removed from the green body prior to the start of the CVI process as temperatures increase in the CVI reactor. The CVI process selective deposits a fully dense coating on all internal and external surfaces of the finished object.

Terrani, Kurt A.↗
DOE OSTI2024

Additive manufacturing of complex objects using refractory matrix materials

A method for the manufacture of a three-dimensional object using a refractory matrix material is provided. The method includes the additive manufacture of a green body from a powder-based refractory matrix material followed by densification via chemical vapor infiltration (CVI). The refractory matrix material can be a refractory ceramic (e.g., silicon carbide, zirconium carbide, or graphite) or a refractory metal (e.g., molybdenum or tungsten). In one embodiment, the matrix material is deposited according to a binder-jet printing process to produce a green body having a complex geometry. The CVI process increases its density, provides a hermetic seal, and yields an object with mechanical integrity. The residual binder content dissociates and is removed from the green body prior to the start of the CVI process as temperatures increase in the CVI reactor. The CVI process selective deposits a fully dense coating on all internal and external surfaces of the finished object.

Terrani, Kurt A.↗
DOE OSTI2023

High-throughput and high-performance lithium-ion batteries via dry processing

A scalable powder-to-electrode dry processing strategy mainly based on powder dry mixing and rolling/calendering is rationally designed. The dry processed electrodes show lower tortuosity compared to that of conventional slurry-based electrodes. The dry-processed high-loading graphite anodes (6.6 mAh cm -2 ) and LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathodes (6.0 mAh cm -2 ) exhibit promising electrochemical performance in half-cells and full-cells. The full-cells with both electrodes from dry processing demonstrates superb rate performance to their counterpart with conventional slurry-based electrodes and delivers of capacity retentions of 74.1 % and 63.6 % over 400 and 800 cycles, respectively. Notably, the initial Coulombic efficiency of the dry processed graphite anodes is low ascribed to polytetrafluoroethylene binder. Finally, the results suggest that dry processing is promising for future lithium-ion battery manufacturing and also pinpoint the needs of modification for the polytetrafluoroethylene binder in the graphite anodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Mesoporous Textured Fe-N-C Electrocatalysts as Highly Efficient Cathodes for Proton Exchange Membrane Fuel Cells

A new platinum group metal (PGM)-free proton exchange membrane fuel cell (PEMFC) cathode catalyst materials, synthesized using the VariPore™ method by Pajarito Powder, LLC, are characterized for their structure and activity. The physico-chemical analysis of the iron-nitrogen-carbon (Fe-N-C) electrocatalysts show mesoporous carbon material effectively doped with iron and nitrogen. The materials have an average pore size of 7-8 nm and high specific surface area. The Fe-N-C catalysts exhibit good oxygen reduction reaction (ORR) activity in 0.5 M H2SO4 electrolyte with high half-wave potential and sustainable electrochemical stability over 10,000 repeated potential cycles with insignificant losses in their activities. As cathode catalysts in a PEMFC, the Fe-N-C materials deliver remarkably good fuel cell performance at low overpotential approaching that of the commercial Pt catalyst. The high ORR electrocatalytic activity of these Fe-N-C catalysts is credited to the synergy between nitrogen-moieties, specifically pyrrolic-N, pyridinic-N, and graphitic-N, and iron in addition to the high mesoporosity that facilitate an effective reaction path in boosting the electrocatalytic activity and stability.

DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Developing solid-surface plasma facing components for pilot plants and reactors with replenishable wall claddings and continuous surface conditioning. Part B: required research in present tokamaks

Abstract The companion part A paper (Stangeby et al 2022) reports a number of independent estimates indicating that high-duty-cycle DT tokamaks starting with pilot plants will likely experience rates of net erosion and deposition of solid PFC, plasma facing component, material in the range of 10 3 to 10 4 kg yr −1 , regardless of the material used. The subsequent redeposition of such large quantities of material has the potential for major interference with tokamak operation. Similar levels and issues will be involved if ∼continuous low-Z powder dropping is used for surface conditioning of DT tokamaks, independent of the material used for the PFC armor. In Stangeby et al (2022) (part A) it is proposed that for high-duty-cycle DT tokamaks, non-metallic low-Z refractory materials such as ceramics (graphite, SiC, etc) used as in situ replenishable, relatively thin—of order mm—claddings on a substrate which is resistant to neutron damage could provide a potential solution for protecting the main walls, while reducing the risk of degrading the confined plasma. Assessment of whether such an approach is viable will require information, much of which is not available today. Section 6 of part A identifies a partial list of major physics questions that will need to be answered in order to make an informed assessment. This part B report describes R&D needed to be done in present tokamaks in order to answer many of these questions. Most of the required R&D is to establish better understanding of low-Z slag generation and to identify means to safely manage it. Powder droppers provide a unique opportunity to carry out controlled studies on the management of low-Z slag in current tokamaks, independent of whether their protection tiles use low-Z or high-Z material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Progress Towards a Titanium-Zirconium-Molybdenum Alloy Coreblock Prototype Using Powder Bed Fusion

Microreactor designs make use of a coreblock for structural stability allowing for these devices to provide powder generation while being portable and inherently safe. In order to maximize energy output of the microreactors, materials must be able to withstand high temperature without melting and without substantial decreases in mechanical properties. As simultaneous projects looking at steels, graphite, and other materials are on-going, this work package will investigate titanium – zirconium – molybdenum alloy (TZM) as it allows for potentially higher microreactor operating temperatures than traditional reactor materials such as stainless steel. Notably, this alloy was developed in the 1960s for use in rockets and has a very high melting point (2623°C) but is difficult to form, machine and join. With limited needs in aerospace, literature is appropriately sparce in looking at the AM of TZM (examples include [1,2]). However, the properties appear to be an excellent match for the needs of the microreactor coreblock leading to the current project. In addition, small washers form the bulk of TZM parts needed in aerospace while the microreactor community was looking at larger, more complex parts. Therefore, AM of TZM is being explored to enable near – net shape of components with the needed complexity to impact the nuclear energy field.

36 MATERIALS SCIENCE↗