Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel assembly design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Design, Analysis and Testing of a PRSEUS Pressure Cube to Investigate Assembly Joints

Due to its potential to significantly increase fuel efficiency, the current focus of NASA's Environmentally Responsible Aviation Program is the hybrid wing body (HWB) aircraft. Due to the complex load condition that exists in HWB structure, as compared to traditional aircraft configurations, light-weight, cost-effective and manufacturable structural concepts are required to enable the HWB. The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept is one such structural concept. A building block approach for technology development of the PRSEUS concept is being conducted. As part of this approach, a PRSEUS pressure cube was developed as a risk reduction test article to examine a new integral cap joint concept. This paper describes the design, analysis and testing of the PRSEUS pressure cube test article. The pressure cube was required to withstand a 2P, 18.4 psi, overpressure load requirement. The pristine pressure cube was tested to 2.2P with no catastrophic failure. After the addition of barely visible impact damage, the cube was pressure loaded to 48 psi where catastrophic failure occurred, meeting the scale-up requirement. Comparison of pretest and posttest analyses with the cube test response agree well, and indicate that current analysis methods can be used to accurately analyze PRSEUS structure for initial failure response.

Yovanof, Nicolette↗
NASA NTRS2000

Defect Characterization in a Thin Walled Composite RP-1 Tank: A Case Study

A full scale thin walled composite tank, designed and fabricated for the storage of pressurized RP- I rocket fuel, was fully inspected with digital infrared thermography (IR) during assembly and prior to proof testing. The tank featured a "pill capsule" design with the equatorial bondline being overwrapped on both the inner and outer surfaces. A composite skirt was bonded to the aft dome of the tank to serve as a structural support when the tank was stood on end in service. Numerous anomalies were detected and mapped prior to proof testing, some along bondlines and some scattered throughout the acreage. After the tank was intentionally burst, coupons were cut from the regions including thermographic anomalies. These coupons were again inspected thermographically to document the growth of any indications due to proof testing. Ultrasonic inspections (UT) were also performed on the coupons for comparison to thermography. Several coupons were dissected and micrographed. Relationships between IR and UT indications and the physical nature of the dissected material are presented.

Langsing, Matthew D.↗
NASA NTRS1993

Viper cabin-fuselage structural design concept with engine installation and wing structural design

This report describes the process and considerations in designing the cabin, nose, drive shaft, and wing assemblies for the 'Viper' concept aircraft. Interfaces of these assemblies, as well as interfaces with the sections of the aircraft aft of the cabin, are also discussed. The results of the design process are included. The goal of this project is to provide a structural design which complies with FAR 23 requirements regarding occupant safety, emergency landing loads, and maneuvering loads. The design must also address the interfaces of the various systems in the cabin, nose, and wing, including the drive shaft, venting, vacuum, electrical, fuel, and control systems. Interfaces between the cabin assembly and the wing carrythrough and empennage assemblies were required, as well. In the design of the wing assemblies, consistency with the existing cabin design was required. The major areas considered in this report are materials and construction, loading, maintenance, environmental considerations, wing assembly fatigue, and weight. The first three areas are developed separately for the nose, cabin, drive shaft, and wing assemblies, while the last three are discussed for the entire design. For each assembly, loading calculations were performed to determine the proper sizing of major load carrying components. Table 1.0 lists the resulting margins of safety for these key components, along with the types of the loads involved, and the page number upon which they are discussed.

Marchesseault, B.↗
NASA NTRS2003

Performance of WPA Conductivity Sensor during Two-Phase Fluid Flow in Microgravity

The Conductivity Sensor designed for use in the Node 3 Water Processor Assembly (WPA) was based on the existing Space Shuttle application for the fuel cell water system. However, engineering analysis has determined that this sensor design is potentially sensitive to two-phase fluid flow (gadliquid) in microgravity. The source for this sensitivity is the fact that gas bubbles will become lodged between the sensor probe and the wall of the housing without the aid of buoyancy in l-g. Once gas becomes lodged in the housing, the measured conductivity will be offset based on the volume of occluded gas. A development conductivity sensor was flown on the NASA Microgravity Plan to measure the offset, which was determined to range between 0 and 50%. Based on these findings, a development program was initiated at the sensor s manufacturer to develop a sensor design fully compatible with two-phase fluid flow in microgravity.

Carter, Layne↗
NASA NTRS1978

Design and analysis of a scramjet engine

Design concepts defined for the cooled-structures assembly of a hydrogen fueled, regeneratively cooled, airframe-integrated Scramjet engine are considered. Engine subsystems, in particular, the fuel subsystem associated with the operating engine are included along with the engine mounting and the interfacing with the airplane. The engine structure and thermal protection system, including the fuel injection struts are emphasized.

Buchmann, O. A.↗
NASA NTRS1991

Heat transfer and core neutronics considerations of the heat pipe cooled thermionic reactor

The authors summarize the results of detailed neutronic and thermal-hydraulic evaluations of the heat pipe cooled thermionic (HPTI) reactor design, identify its key design attributes, and quantify its performance characteristics. The HPTI core uses modular, liquid-metal core heat transfer assemblies to replace the liquid-metal heat transport loop employed by in-core thermionic reactor designs of the past. The nuclear fuel, power conversion, heat transport, and heat rejection functions are all combined into a single modular unit. The reactor/converter assembly uses UN fuel pins to obtain a critical core configuration with in-core safety rods and reflector controls added to complete the subassembly. By thermally bonding the core heat transfer assemblies during the reactor core is coupled neutronically, thermally, and electrically into a modular assembly of individual power sources with cross-tied architecture. A forward-facing heat pipe radiator assembly extends from the reactor head in the shape of a frustum of a cone on the opposite side of the power system from the payload. Important virtues of the concept are the absence of any single-point failures and the ability of the core to effectively transfer the TFE waste heat load laterally to other in-core heat transfer assemblies in the event of multiple failures in either in-core and radiator heat pipes.

Determan, W. R.↗
NASA NTRS1981

High-pressure LOX/hydrocarbon preburners and gas generators

The objective of the program was to conduct a small scale hardware test program to establish the technology base required for LOX/hydrocarbon preburners and gas generators. The program consisted of six major tasks; Task I reviewed and assessed the performance prediction models and defined a subscale test program. Task II designed and fabricated this subscale hardware. Task III tested and analyzed the data from this hardware. Task IV analyzed the hot fire results and formulated a preliminary design for 40K preburner assemblies. Task V took the preliminary design and detailed and fabricated three 40K size preburner assemblies, one each fuel-rich LOX/CH, and LOX/RP-1 and one oxidizer rich LOX/CH4. Task VI delivered these preburner assemblies to MSFC for subsequent evaluation.

Huebner, A. W.↗
NASA NTRS1984

Erectable Space-Construction Fixture

Concept for erectable space construction fixture described in report. Fixture combines all equipment required for construction of framework for space platform into single compact work station. Almost all aspects of assembly and farication automated. Design goals for fixture include platform assembly in shortest possible time and minimizing fuel and power requirements of support spacecraft.

Thompson, R. R.↗
NASA NTRS1979

Conference on Advanced Technology for Future Space Systems, Hampton, Va., May 8-10, 1979, Technical Papers

Propulsion systems for spacecraft, satellite communications technology, the design of large light-weight erectable structures for assembly in space, electronics and information processing for spacecraft, and self-diagnostic, fault-tolerant controls based on high memory and processing capabilities are discussed. Topics of the papers include the design of large delta wings for earth-to-orbit transports, dual-fuel propulsion units, magnetoplasmadynamic thrusters, heating rates on blunt-nosed bodies at various angles of attack, remote manipulators for space assembly tasks, solar electric propulsion for planetary missions, deployable space platforms with multiple payloads, the design of large offset-fed antennas, a nonlinear stress-strain relationship for metallic meshes, and adaptive sensors for spacecraft.

Source record↗
NASA NTRS1981

Cell module and fuel conditioner development

The results of pretesting and performance testing of Stack 564 are reported. The design features, progress in fabrication and plans for assembly of Stack 800 are given. The status of endurance testing of Stack 560 is reported. The design, fabrication, test procedures and preliminary tests of the 10 kW double counterflow reformer and the reformer test stand are described. Results of vendor contacts to define the performance and cost of fuel conditioning system components are reported. The results of burner tests and continuing development of the BOLTAR program are reported.

Hoover, D. Q., Jr.↗
NASA NTRSDate not supplied

Multidisciplinary Optimization of A Transonic Truss-Braced Wing Aircraft Using Aviary

The continuous push to decrease fuel burn of single-aisle commercial aircraft has led to interest in a Transonic Truss-Braced Wing (TTBW) concept vehicle. Sporting high-slung wings that are long and slender to increase aerodynamic efficiency, a TTBW can also accommodate higher-bypass turbine engines. The combination of these two changes potentially leads to an overall decrease in fuel consumption. In this paper, a TTBW concept vehicle is assembled in the Aviary open-source tool for conceptual aircraft design. The conceptual-level aerodynamics and propulsion systems that come prepackaged with Aviary are replaced with higher-fidelity vortex lattice method for aerodynamics (VSPAERO) and a one-dimensional cycle analysis tool for propulsion (pyCycle). The vehicle is then optimized to minimize fuel burn for a representative commercial mission. Design parameters for the vehicle include the electrified turbine size, the size of the electric motors which are used for takeoff and climb assist, and battery capacity. The TTBW concept vehicle presented in this paper represents the first application of Aviary to an aircraft design problem.

Optimization↗
NASA NTRS1974

Linear Test Bed. Volume 2: Test Bed No. 2

Test bed No. 2 consists of 10 combustors welded in banks of 5 to 2 symmetrical tubular nozzle assemblies, an upper stationary thrust frame, a lower thrust frame which can be hinged, a power package, a triaxial combustion wave ignition system, a pneumatic control system, pneumatically actuated propellant valves, a purge and drain system, and an electrical control system. The power package consists of the Mark 29-F fuel turbopump, the Mark 29-0 oxidizer turbopump, a gas generator assembly, and propellant ducting. The system, designated as a linear aerospike system, was designed to demonstrate the feasibility of the concept and to explore technology related to thrust vector control, thrust vector optimization, improved sequencing and control, and advanced ignition systems. The propellants are liquid oxygen/liquid hydrogen. The system was designed to operate at 1200-psia chamber pressure at an engine mixture ratio of 5.5. With 10 combustors, the sea level thrust is 95,000 pounds.

Source record↗
NASA NTRS1977

NASA Quiet Clean General Aviation Turbofan (QCGAT) program status

The suitability of large engine technology to reduce noise, emissions, and fuel consumption of small turbine engines and develop new technology where required is determined. The design, fabrication, assembly, test, and delivery of the experimental engines to NASA are discussed.

Bresnahan, D. L.↗
NASA NTRS1985

Low-Loss Fuel and Oxidizer Injector

Pressure losses reduced without degrading combustion stability. Injection Posts form forest in cavity between oxygen manifold and secondary faceplate. Cavity is fuel manifold; fuel floods post forest and enters each post through side holes in shroud. Injector designed for improved assembly and maintenance. Posts accessible from primary combustion chamber side and changed for flow adjustment.

Pragemau, G. L.↗
NASA NTRS1991

Particle bed reactor nuclear rocket concept

The particle bed reactor nuclear rocket concept consists of fuel particles (in this case (U,Zr)C with an outer coat of zirconium carbide). These particles are packed in an annular bed surrounded by two frits (porous tubes) forming a fuel element; the outer one being a cold frit, the inner one being a hot frit. The fuel element are cooled by hydrogen passing in through the moderator. These elements are assembled in a reactor assembly in a hexagonal pattern. The reactor can be either reflected or not, depending on the design, and either 19 or 37 elements, are used. Propellant enters in the top, passes through the moderator fuel element and out through the nozzle. Beryllium used for the moderator in this particular design to withstand the high radiation exposure implied by the long run times.

Ludewig, Hans↗
NASA NTRS1979

Thermal-structural Design Study of an Airframe-integrated Scramjet

Design concepts for the cooled structures assembly for the Langley Scramjet engine, for engine subsystems, and for the aircraft/engine interface were developed and evaluated. Results show that the objectives for the Scramjet engine can be met. A thermal protection system was defined that makes it possible to attain a life of 100 hours and 1000 cycles, which is the specified goal. With stoichiometric combustion, the fuel provides an adequate heat sink for cooling the engine at Mach numbers up to 9 at the minimum fuel flow condition. The mechanical design is feasible for manufacture using conventional materials. For the cooled structures in a six-module engine, the mass per unit capture area is 1328 kg/sq m (259 lb/sq ft). The total mass of a six-module engine assembly including the fuel system is 1577 kg (3477 lb).

Buchmann, O. A.↗