Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel additive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Additive-Mixing Fuel Injection (AMFI): A device for robust control and improved performance of high-efficiency LTGC engines

Low-temperature gasoline combustion (LTGC) engines can provide high efficiencies with very low NOx and particulate emissions. Despite these major advantages, methods for controlling LTGC combustion timing, achieving robust autoignition, and good low-load performance have challenged the development of practical LTGC engines. A key reason is that the ideal reactivity of the fuel varies with operating conditions, with low-reactivity fuels working well at high loads and higher-reactivity fuels working better at low loads. This article introduces a new technique called Additive Mixing Fuel Injection (AMFI) that adjusts the reactivity of the gasoline to obtain good performance over the operating map. Moreover, AMFI can provide robust combustion-timing control because it precisely meters very small amounts (0.01–0.6 mm 3 ) of an ignition-enhancing additive into the fuel each engine cycle. The additive used was 2-ethylhexyl nitrate (EHN), a common, inexpensive diesel-fuel ignition improver, but other additives could be used. Because additive amounts are so small, a 2-gal reservoir would be sufficient for medium-duty applications with refilling only at service intervals of about 8000 mi. The AMFI system has been installed on a single-cylinder LTGC research engine and demonstrated to provide robust combustion-timing control over wide ranges of combustion phasing, fueling rate, intake boost, engine speed, and intake temperature. AMFI also increases the fuel’s reactivity sufficiently to greatly reduce or eliminate the need for charge heating, simplifying engine design and significantly increasing thermal efficiency and the maximum load at low-boost conditions. The nitrogen in the EHN produced a modest increase in NOx, but it was mitigated by lower intake temperatures, and NOx emissions remained very low. Finally, the additive increases the sensitivity of autoignition reactions to variations in the local fuel/air mixture within the charge. This allows the use of controlled fuel stratification for improved LTGC-engine performance, and its potential to improve low-load operation was demonstrated.

Dec, John E.↗
DOE OSTI2019

Screening Compounds for Fast Pyrolysis and Catalytic Biofuel Upgrading Using Artificial Neural Networks

Abstract There is significant interest among researchers in finding economically sustainable alternatives to fossil-derived drop-in fuels and fuel additives. Fast pyrolysis, a method for converting biomass into liquid hydrocarbons with the potential for use as fuels or fuel additives, is a promising technology that can be two to three times less expensive at scale when compared to alternative approaches such as gasification and fermentation. However, many bio-oils directly derived from fast pyrolysis have a high oxygen content and high acidity, indicating poor performance in diesel engines when used as fuels or fuel additives. Thus, a combination of selective fast pyrolysis and chemical catalysis could produce tuned bioblendstocks that perform optimally in diesel engines. The variance in performance for derived compounds introduces a feedback loop in researching acceptable fuels and fuel additives, as various combustion properties for these compounds must be determined after pyrolysis and catalytic upgrading occurs. The present work aims to reduce this feedback loop by utilizing artificial neural networks trained with quantitative structure-property relationship values to preemptively screen pure component compounds that will be produced from fast pyrolysis and catalytic upgrading. The quantitative structure-property relationship values selected as inputs for models are discussed, the cetane number and sooting propensity of compounds derived from the catalytic upgrading of phenol are predicted, and the viability of these compounds as fuels and fuel additives is analyzed. The model constructed to predict cetane number has a test set prediction root-mean-squared error of 9.874 cetane units, and the model constructed to predict yield sooting index has a test set prediction root-mean-squared error of 13.478 yield sooting index units (on the unified scale).

09 BIOMASS FUELS↗
NASA NTRS1989

NOx formation from the combustion of monodisperse n-heptane sprays doped with fuel-nitrogen additives

A series of experiments with simulated synthetic fuels were conducted in order to investigate the effect of droplet size on the conversion of fuel-nitrogen to NOx. Pyridine and pyrrole were added to n-heptane as nitrogen-containing additives and burned as monodisperse fuel droplets under various operating conditions in a spray combustion facility. The experimental results indicate that under stoichiometric and fuel-rich conditions, reducing the droplet size increases the efficiency of fuel-N conversion to NOx. This observation is associated with improved oxidation of the pyrolysis fragments of the additive by better oxygen penetration through the droplet flame zone. The dominant reactions by which fuel-N is transformed to NOx were also considered analytically by a premixed laminar flame code. The calculations are compared to the small droplet size results.

Sarv, Hamid↗
DOE OSTI2021

Next-Cycle Optimal Fuel Control for Cycle-to-Cycle Variability Reduction in EGR-Diluted Combustion

In this simulation study, cycle-to-cycle fuel control was used to reduce CCV by injecting additional fuel in operating conditions with sporadic misfires and partial burns. An optimal control policy was proposed that utilizes 1) a physics-based model that tracks in-cylinder gas composition and 2) a one-step-ahead prediction of the combustion efficiency based on a kernel density estimator. The optimal solution, however, presents a tradeoff between the reduction in combustion CCV and the increase in fuel injection quantity required to stabilize the charge. Such a tradeoff can be ad- just by a single parameter embedded in the cost function.

Maldonado, BryanP. [Oak Ridge National Lab. (ORNL)↗
NASA NTRS1975

Investigation A: Numerical solutions of driven vortices of binary fluid in a cylindrical geometry

The steady state laminar motion of a viscous, incompressible and binary fluid is studied for a rotating flow in a cylindrical geometry. The mathematical model employed is a cold flow simulation of the fluid mechanics of the light-bulb concept of the gaseous core nuclear engine. A numerical treatment is developed for the rotating flow which includes a description of the nuclear fuel addition. The problem is formulated with the complete Navier-Stokes equations in order to show the interaction between the fuel addition, the main flow, and the boundary layer flow in an accurate manner. The results presented show holdup of the nuclear fuel for the case of steady fuel addition.

Shin, Y. W.↗
DOE OSTI2021

Modeling Summary of ASNF in DOE Sealed Standard Canisters

A pathway for road-ready and final disposition packaging configurations for the aluminum-clad spent nuclear fuel (ANSF) fuel dictates storage within helium backfilled sealed DOE standard canisters. The typical packaging configuration for the 15-foot DOE canisters places 10 advance test reactor (ATR) elements within a Type 1a basket, and three baskets are loaded within each DOE canister. During in-reactor operations and cooling pond storage conditions, oxyhydroxide layers form on the surface of the aluminum clad fuel. These layers produce hydrogen gas over time due to the fuel’s radiation field. As part of the packing procedure, the ATR fuel should be dried to remove any residual physio-/chemi- sorbed water bound to the surface. The results of this modeling will include results at fully saturated and fully dried conditions. In addition, fuels that are currently stored at the Savannah River Site were also studied for their potential for hydrogen and pressure build up. These two additional fuels modeled were the Missouri University Research Reactor (MURR) fuel, which is packaged in the same configuration as the ATR, but with a 10-foot-tall DOE standard canister. This was selected due to its relatively high decay heat compared to other DOE-managed ASNF. The second additional fuel studied with the modeling effort was the High Flux Isotope Reactor (HFIR) fuel. This fuel is modeled as two separate DOE canisters with the inner and outer annulus split for storage. The HFIR was selected for study due to its high aluminum cladding surface area. In the associated experimental work, Task 2 - Oxyhydroxide Layer Radiolytic Gas Generation Resolution, additional tests were completed in a helium environment, and updated G-values for the radiolytic production of hydrogen from the oxyhydroxide layers were provided. These values were 2.92 ×10 -4 µmol/J at 50% relative humidity and 4.12 ×10 -4 µmol/J at 100% relative humidity. These values are lower than the value for Argon that was used in prior modeling results. In addition, prior modeling results have been completed with the G-value applied to just the mass of the corrosion layer, and this has been updated to apply the G-value for hydrogen generation to the full mass of the fuel. These two effects combine to show much smaller pressure and hydrogen build up for the sealed canister model. For a nominal scenario of stored ATR fuel, after 50 years the model results give a 1.36 atm total pressure, 7% mole percent hydrogen, for the upper decay heat, 1.51 atm total pressure, 16% mole percent hydrogen, and for upper decay heat with undried fuel 2.6 atm total pressure, 15% mole percent hydrogen. For the MURR nominal case, the model results give 1.34 atm and 6% hydrogen, for upper decay heat this gives 1.41 atm total pressure with 10.8 % hydrogen, and for upper decay heat with undried fuel, this gives 2.38 atm total pressure with 9.9% hydrogen. The nominal scenario for HFIR fuel gives 1.39 atm total pressure with 9.9% hydrogen, the upper decay heat case gives 1.43 atm with 12.1% hydrogen, and the upper decay heat with undried fuel gives 2.17 atm total pressure with 11.9% hydrogen. These results confirm the ATR scenario bounds the other intact ASNF modeled here. No case modeled yields significant oxygen, and the lower decay heat cases for all fuels modeled have hydrogen concentrations that are under the 4% flammability limit after 50 years of storage. In addition, the modeled pressures for all cases are all significantly below the 500-psi limit for the DOE standard sealed canister.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

A comparison of computational models for predicting yield sooting index

Sooting propensity, a measurement of how much particulate matter is produced when a fuel is burned, is a property of significant interest among researchers who are striving to discover the next generation of cleaner, more efficient fuels and fuel additives. Many compounds are not viable as fuels and/or fuel additives, and as a result, designing cleaner-burning biofuels using only experimental techniques is inefficient. Predictive models have been instrumental in reducing this inherent difficulty, providing researchers with a tool to preemptively screen compounds before production and testing. The present work compares the accuracies and interpretabilities of existing models used to predict a particular measure of sooting propensity, Yield Sooting Index (YSI). These models include artificial neural networks, graph neural networks, and multivariate equations. A novel equation for predicting YSI based on atom path count and bond order is proposed, which can highlight key structural components that contribute to YSI. It was found that artificial neural networks slightly outperform graph neural networks and greatly outperform multivariate equations in blind (test set) prediction accuracy; however, graph neural networks and multivariate equations provide significantly more interpretability as to how compound structure relates to YSI. Predictions of YSI are compared to experimental measurements for previously un-tested compounds with cetane numbers comparable to diesel fuel (50-60) (butyl decanoate, ethyl decanoate, 1,4-bis(ethenoxymethyl)cyclohexane, and 5-heptyloxolan-2-one), and it was found that these compounds produce significantly less soot compared to diesel fuel.

09 BIOMASS FUELS↗
DOE OSTI2022

Prospects for additive manufacturing of nuclear fuel forms

Additive manufacturing (AM) is viewed as a critical enabling technology for achieving superior performance and improved economics across many sectors. Although the past decade has seen increased application of AM methods to nuclear reactor cladding and structural materials, exploration of AM as applied to the uranium-bearing nuclear fuel forms has been limited. The two major families of nuclear fuel forms (monolithic, particle/dispersion) are utilized with their own set of core objectives in mind, and their differences require distinct fabrication infrastructures. These reference fabrication methods impose many limitations on nuclear fuels. Further, both currently operating reactors and future concepts have the potential for improved performance if these accepted limitations are relaxed or removed entirely. The primary limitations of reference fabrication processes for the common nuclear fuel forms are outlined in this paper. This groundwork is then used to identify avenues of fuel performance specific to each of these fuel architectures that could be exploited if the restrictions of conventional fuel fabrication are removed. Moreover, multiple targets for AM studies are laid out for each of the major nuclear fuel variants. Finally, key strategic components to guide research activities in AM of nuclear fuels are outlined, with an emphasis on use of modeling and simulation to motivate research aims and embrace of an accelerated testing methodology to screen and quality new fuel forms.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

A Rapid Compression Machine Study of 2-Phenylethanol Autoignition at Low-To-Intermediate Temperatures

To meet the increasing anti-knocking quality demand of boosted spark-ignition engines, fuel additives are considered an effective approach to tailor fuel properties for satisfying the performance requirements. Thus, screening/developing bio-derived fuel additives that are best-suited for advanced spark-ignition engines has become a significant task. 2-Phenylethanol (2-PE) is an attractive candidate that features high research octane number, high octane sensitivity, low vapor pressure, and high energy density. Recognizing that the low temperature autoignition chemistry of 2-PE is not well understood and the need for fundamental experimental data at engine-relevant conditions, rapid compression machine (RCM) experiments are therefore conducted herein to measure ignition delay times (IDTs) of 2-PE in air over a wide range of conditions to fill this fundamental void. These newly acquired IDT data at low-to-intermediated temperatures, equivalence ratios of 0.35–1.5, and compressed pressures of 10–40 bar are then used to validate the 2-PE model developed by Shankar et al. (2017). It is found that this literature model greatly overpredicts the current RCM data. The comparison of experimental and simulated results also provides insights into 2-PE autoignition behaviors at varying conditions. Further chemical kinetic analyses demonstrate that the absence of the O2-addition pathway of β-R. radical in the 2-PE model of Shankar et al. (2017) could account for the model discrepancies observed at low-to-intermediated temperatures.

Fang, Ruozhou (ORCID:0000000348315100)↗
DOE OSTI2023

Multiphysics analysis of fuel Fragmentation, Relocation, and dispersal Susceptibility–Part 2: High-Burnup Steady-State operating and fuel performance conditions

The US nuclear industry is pursuing increased cycle lengths and increasing the peak rod-averaged burnup in an effort to increase the economic viability of the US nuclear fleet. Increasing burnup will afford economic viability by enabling utilities to optimize core designs to reduce the number of fresh fuel assemblies per cycle and allow nuclear power plants to operate for a longer period of time. Longer operating periods will also decrease the number of outages experienced by a nuclear power plants and, therefore, offer utilities significant operational savings. However, extending the peak rod-averaged burnup beyond 62 GWd/tU results in operating fuel rods to higher burnup under higher power conditions. This operating regime is expected to result in higher fuel temperatures, fission gas release (FGR), and rod internal pressures (RIPs) that may challenge historical safety basis and affect high-burnup (HBU) experimental testing. In particular, these conditions directly affect fuel fragmentation, relocation, and dispersal (FFRD) susceptibility, so understanding the pretransient operating conditions is critical for developing test plans that evaluate the FFRD and develop strategies to mitigate it. This paper evaluates the operating conditions and fuel performance of HBU (greater than62 GWd/tU rod average) fuel. Additionally, it investigates fuel performance sensitivities and discusses the effect on fuel performance. Here, this work used two codes. Virtual Environment for Reactor Applications (VERA) was used to calculate steady-state power histories, identify HBU operating conditions using 10 different realistic HBU core designs, and down-select rods to a representative subset of fuel rods for subsequent BISON evaluation. The BISON fuel performance code was used to investigate steady-state HBU operating conditions and assess uncertainties associated with FGR and its effect on fuel temperatures and RIPs. The VERA and BISON results will provide direct input for HBU experimental testing and support subsequent TRACE and BISON transient fuel performance analyses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Developing renewable free fatty acid surfactants to form diesel blendstocks

Sylvatex technology blends renewable components into diesel to create a low-carbon, blended fuel with significantly cleaner emissions. Sylvatex MicroX blendstock uses low-cost inputs to produce both the fuel additive and alternative fuel products. LBNL worked with to evaluate various hydrolysates and explore different feedstocks that can be grown as commodities and used to produce the renewable surfactant.

09 BIOMASS FUELS↗
NASA NTRS1996

Fundamental Phenomena on Fuel Decomposition and Boundary-Layer Combustion Precesses with Applications to Hybrid Rocket Motors: Experimental Investigation - Part 1

This final report summarizes the major findings on the subject of 'Fundamental Phenomena on Fuel Decomposition and Boundary-Layer Combustion Processes with Applications to Hybrid Rocket Motors', performed from 1 April 1994 to 30 June 1996. Both experimental results from Task 1 and theoretical/numerical results from Task 2 are reported here in two parts. Part 1 covers the experimental work performed and describes the test facility setup, data reduction techniques employed, and results of the test firings, including effects of operating conditions and fuel additives on solid fuel regression rate and thermal profiles of the condensed phase. Part 2 concerns the theoretical/numerical work. It covers physical modeling of the combustion processes including gas/surface coupling, and radiation effect on regression rate. The numerical solution of the flowfield structure and condensed phase regression behavior are presented. Experimental data from the test firings were used for numerical model validation.

Kuo, Kenneth K.↗
NASA NTRS1997

Experimental Analysis of a Rocket Based Combined Cycle (RBCC) Engine in a Direct-Connect Test Facility

The object of this study is to investigate the operation of a RBCC at ramjet and scramjet flight conditions using a direct-connect test facility. The apparatus being tested is a single strut-rocket within a dual-mode ram/scramjet combustor. The gaseous hydrogen/oxygen, linear strut-rocket was supplied by Aerojet Propulsion Company. The hardware is being tested in the Direct Connect Supersonic Combustion Test Facility at NASA Langley Research Center. The test facilities hydrogen/oxygen vitiated heater is capable of flight total enthalpies to Mach 8. A Mach 2.5 facility nozzle mates the heater to the combustor duct. The rocket ejector will ordinarily operate in a fuel-rich mode. Additional fuel injection is provided by a pair of parallel injectors located at the base of the strut body. Instrumentation on the test apparatus includes a unique, direct thrust measurement system. Performance predictions for the anticipated test conditions have been made using a one-dimensional, thermodynamic analysis code. Results from the code show the dependence of overall thrust and specific impulse on rocket chamber pressure, rocket fuel equivalence ratio, and overall fuel equivalence ratio. Once the experimental test series begins, the inferred combustion efficiency as a function of axial location and the thermal choke region (where applicable) can also be determined using this code. Upon completion of the experimental test series, measurements will be used to calculate thrust, specific impulse, etc. Measured and calculated values will be compared to those found analytically. If appropriate, the code will be tailored to better predict hardware operation. Conclusions will be drawn as to the fuel-rich rocket's overall effect on ramjet and scramjet performance. Also, comparisons will be made between the integrated thrust calculated from the static pressure taps located along the duct and the thrust measured by the direct thrust measurement system.

K. Nelson↗
DOE OSTI2025

Tungsten single-atom catalysts for the efficient conversion of isobutene into highly branched liquid hydrocarbons

The catalytic transformation of isobutene into branched liquid hydrocarbons is crucial for the production of reformulated gasoline and fuel additives. Conventional supported catalysts often lack high activity and selectivity toward the desired highly branched dimers and trimers in isobutene oligomerization. Here, by developing a tungsten single-atom catalyst (W SAC ) atomically dispersed on a silica-doped alumina (SDA) support, we report that the W SAC /SDA catalyst enables efficient and selective conversion of isobutene into highly branched C 8 and C 12 liquid olefins while suppressing the formation of heavier hydrocarbons. The atomically dispersed W 1 –O 3 moieties incorporated within the SDA support were synthesized via a high-temperature pyrolysis of a templating zinc metal–organic framework (Zn-MOF) under argon, followed by annealing in static air. The W SAC /SDA catalysts with 1.6–3.7 wt% W loading exhibited single-atom dispersion (∼0.2 nm) and outstanding performance, achieving up to 60% and 95% selectivity to branched C8 olefins at 150 °C and 250 °C, respectively, under ambient pressure. With the demonstrated high activity, selectivity, and stability, the W SAC /SDA catalyst system presents a promising platform for next-generation heterogeneous catalysts for the efficient and selective upgrading of isobutene into high-performance fuel additives.

Branched Olefins↗
NASA NTRS2005

Monopropellant combustion system

An apparatus and method are provided for decomposition of a propellant. The propellant includes an ionic salt and an additional fuel. Means are provided for decomposing a major portion of the ionic salt. Means are provided for combusting the additional fuel and decomposition products of the ionic salt.

Berg, Gerald R.↗
DOE OSTI2023

Isomeric effects on the reactivity of branched alkenes: An experimental and kinetic modeling study of methylbutenes

Here, a detailed experimental study of the low-to-intermediate temperature combustion of methylbutene isomers, i.e., branched C 5 alkenes, has been undertaken with multiple experimental facilities. Ignition delay times were measured at equivalence ratios 0.5–2.0, 685–1020 K and up to 45 bar condition from two rapid compression machines and showed slight deviation from an Arrhenius behavior for all three isomers, while their reactivity order differs as temperature changes. Sampled intermediates formed during the oxidation process of mixtures at 900–1150 K and 0.82 bar from a flow reactor and at 730 K and 20 bar from a rapid compression machine were analyzed using gas chromatography techniques. Trends in the formation and consumption of sampled intermediates were modeled using a kinetic model developed in this work for all three isomers. Rate of production and sensitivity analyses emphasize the role of double bond-specific reactions governing the global reactivity of these fuels. Additional studies of the addition reactions of HO 2 radicals to the double bond and to allylic radicals may improve the model performance.

2-Methyl-1-butene↗