Results for “Fuel Cladding Qualification” — Page 2

DOE OSTI2023

High temperature creep model development using in-situ 3-D DIC techniques during a simulated LOCA transient

In-situ strain measurements of fuel cladding can enable high-throughput data collection and validation to support accelerated qualification of cladding materials. Here, in this work, 3D digital image correlation was used to map strain for both Zircaloy-4 (Zry-4) and Cr-coated Zry-4 during two types of cladding rupture experiments: isobaric temperature ramp tests at 5 °C/s and isothermal pressure jump tests at 600 °C. Zry-4 strain data initially showed a temperature dependence expected for creep deformation, yet a shift to a new plastic deformation mechanism not reported in literature dominated during the finals seconds prior to rupture. Cr-coated Zry-4 did not show the change in deformation mechanism at the end of life and showed a delay in measurable creep deformation. Stress dependences were similar for Zry-4 and Cr/Zry-4 during pressure jump tests. Cr-coatings were found to decrease the strain rate during both testing scenarios. Creep parameters were calculated to support modelling efforts regarding design basis accidents.

36 MATERIALS SCIENCE↗

DOE OSTI2018

Compatibility Of U 3 Si 2 Fuel With Zr, FeCrAl and SiC/SiC Based Cladding

U 3 Si 2 fuel with FeCrAl or SiC/SiC composite cladding is being considered as an advanced concept and accident tolerant fuel (ATF) system for light water reactors. Understanding their chemical compatibility under operational and accident conditions is fundamental to predicting behavior and fuel qualification. In the present work, experimental determination of interactions and thermodynamic and first principle calculation methods were employed to assess U 3 Si 2 compatibility with novel cladding of FeCrAl-alloys and SiC composites, and were contrasted with compatibility with Zircaloy-4. Diffusion-couple experiments were performed to simulate fuelcladding conditions and the samples were subjected to characterization by scanning electron microscopy and x-ray diffraction. Thermodynamic calculations, based in part on newly determined thermodynamic properties, were used to predict the equilibrium state of the studied systems and to interpret experimental results. First principles calculations using density functional theory were employed to obtain incorporation energies for carbon, iron and uranium in U 3 Si 2 , α- Fe, and SiC structures. Together, the experimental and modeling results have allowed evaluation of the nature of interactions in the fuel-cladding systems.

36 MATERIALS SCIENCE↗

DOE OSTI2021

A Combinatorial Approach to Testing and Characterization of Irradiated Fuels and Materials

•Combinatorial approaches to testing and characterization of materials is a very powerful tool to help explore some fundamentals of materials science.? •Three topics will be explored to help illustrate this:? •A fitness-for-service assessment of a CANDU component (this is work from my past)? •The use of small-scale mechanical testing of Cr-coated ATF cladding in support of qualification (this is work developed upon joining INL)? •A multi-scale characterization approach of TRISO fuel to investigate fission gas migration and microstructural features (this is work I now get to participate in on joining MFC)? •?

36 - MATERIALS SCIENCE↗

DOE OSTI2025

Advanced Fuels Campaign Execution Plan

The Advanced Fuels Campaign (AFC) Execution Plan details the strategy, mission, scope, and goals—both near-term and long-term—along with the structure and organization of nuclear fuels and materials research, development, and demonstration (RD&D) activities within the Fuel Cycle Technologies (FCT) program. The FCT program, tasked by the U.S. Department of Energy (DOE), employs a science-based approach to advance fuel technologies. This approach integrates theory, experiments, and multi-scale modeling and simulation (M&S) to develop a predictive understanding of fuel fabrication processes and fuel/cladding performance under irradiation, moving beyond traditional empirical methods. The long-term goals of the AFC are guided by the AFC Strategic Plan and align with the DOE Office of Nuclear Energy (NE) Roadmap [1], which outlines a multi-decade vision for demonstrating and qualifying advanced fuel forms to support diverse fuel cycle options. Near-term goals focus on enhancing accident tolerant fuels (ATF) for Light Water Reactors (LWR), a significant challenge that demands balancing immediate objectives with ongoing progress toward advanced reactor missions. Accelerating the traditional fuel qualification process to meet ATF objectives is another critical challenge. A detailed set of 5-year goals, summarized below, has been developed in line with the overarching science-based fuel development approach: • Advanced LWR Fuel Technologies: By 2027, support the development of advanced LWR fuel technologies with improved performance and enhanced accident tolerance. This includes high burnup (HBu), low enriched uranium (LEU)+, coated cladding, and doped fuel, aimed at complementing industry-led significant LWR uprates and plant refurbishments. • Tristructural Isotropic (TRISO) Fuel: Achieve qualification by 2028 and develop improved designs for emerging markets. • Metal Fuel: Achieve qualification by 2028 and develop improved designs for emerging markets. • Molten Salt Fuel: By 2027, deploy a robust program that enables fuel salt qualification technologies needed to support fuel salt research and development (R&D), focusing on emergent needs to derisk fuel salt production and utilization in advanced reactors. • Long-Term ATF: Develop fuel technologies that enable significant power uprates (~50%) in refurbished or new LWRs while optimizing fissile material utilization and waste disposal. The 5-year milestones in the AFC Execution Plan are contingent on an assumed budget. This Execution Plan will be updated annually to reflect actual funding profiles as budget guidance becomes available, ensuring milestones are adjusted accordingly. In summary, the AFC Execution Plan presents a comprehensive strategy to advance nuclear fuel technologies through a science-based approach, addressing both near-term and long-term goals while adapting to funding realities.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2016

Monolithic U-10Mo Fuel Development for U.S. High Performance Research Reactors

To support the U.S Department of Energy (DOE), National Nuclear Security Administration (NNSA) mission to reduce the threat posed by the civilian use of highly enriched uranium (HEU) worldwide, the US High Performance Research Reactor (US HPRR) fuel development program is pursuing development and qualification of a new high-density monolithic U-Mo fuel to facilitate conversion of five higher power research reactors located in the U.S. (ATR, HFIR, NBSR, MIT and MURR) and one critical facility (ATR-C) from HEU to low enriched uranium (LEU). These reactors require higher uranium fuel density than is achievable with dispersion fuel systems used to convert lower power research reactors. The down selected fuel system consists of U-10Mo alloy fuel foils having a thin Zr diffusion barrier interlayer, clad in 6061 Al alloy by hot isostatic pressing. In order to support fabrication development, fuel performance evaluations, generic fuel qualification through the Nuclear Regulatory Commission (NRC), and eventual reactor licensing, a series of irradiation experiments and testing campaigns are being planned. The tests are designed to provide data needed for fabrication process down selection, to establish acceptable fuel performance under normal operating conditions and anticipated transients, and to demonstrate successful scale-up to prototypic reactor-specific fuel element designs. A comprehensive testing program is being executed as part of the US HPRR fuel development program to develop and qualify a new monolithic UMo fuel system to allow conversion of five high power research reactors and one critical facility within the US in support of the NNSA mission to convert research reactors worldwide from HEU to LEU fuels. A significant outcome of this program will be the qualification and eventual licensing of a new plate-type fuel system for use in research reactors through the NRC for the first time in nearly 3 decades. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2016

Fabrication and Qualification of Small Scale Irradiation Experiments in Support of the Accident Tolerant Fuels Program

The Accident Tolerant Fuels (ATF) program aims to develop next generation Light Water Reactor (LWR) fuels with improved performance, reliability, and safety. The program has developed a roadmap to support the insertion of lead fuel rods (LFRs) or lead fuel assemblies (LFAs) of an accident tolerant fuel into a commercial LWR by the end of FY 2022. In order to achieve this goal, novel fuel compositions and cladding materials are being assembled as drop-in irradiation experiments to allow for prioritization of concepts to further the ATF mission. Development of fabrication methodology and qualification techniques for small-scale irradiation test samples is reported.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

A Design and Fabrication Options Trade Study for Metallic Fuel without Internal Sodium Bonding

Nuclear fuels using alloys of uranium, or metallic fuels, have many beneficial properties. The classical metallic fuel design uses a loose fitting cylindrical “slug” of fuel placed inside stainless-steel cladding tubes where the gap is filled with sodium. This sodium bond is liquid at operating temperature and conducts heat from the slug to the cladding, especially in early life before fuel swells into contact with the cladding. Despite the benefits of sodium bonding, there is a desire to develop metallic fuel technologies without it chiefly to reduce chemical reaction hazards in spent fuel storage from sodium fast reactors operating on once-through fuel cycles. Elimination of the sodium bond may also help unlock potential benefits for fuel fabrication, reactor neutronics, and compatibility with other types of reactors. Creating a sodium-free metallic fuel revolves around the problem of manufacturing fuel slug geometries which are in close contact with the cladding at beginning of life to facilitate heat transport while alleviating fuel-cladding chemical interactions (FCCI) at this interface and providing enough free volume to accommodate fuel swelling. Accelerating development and qualification of this fuel system will require careful selection of design and manufacturing options. To this end, a design trade-off study was performed to evaluate candidate options. Several design and manufacturing options were assessed, weighted, scored, and ranked with respect to fabrication, normal reactor operation, off-normal scenarios, and back-end considerations. This effort was performed both for “baseline” needs, which represented a once-through fuel cycle at temperatures and burnups known to be viable for sodium-bonded metallic fuel, and for “enhanced” needs to represent opportunities for closed fuel cycles and/or more aggressive temperatures/burnups. The outcomes of this study prioritized a baseline technology using U-Zr alloy with additives to mitigate FCCI, produced in annular slug geometry by continuous casting, clad in austenitic stainless-steel alloy, and followed by a final step to swage the cladding down to close the gap. This study prioritized an enhanced fuel technology using U-Mo alloy, also produced by continuous casting into an annular geometry, followed by coating/plating with an FCCI barrier on the slug, again with a final step to swage the cladding diameter down using oxide dispersion strengthened steel. It was noted that development of the enhanced fuel technology would entail more risk, thus U-Zr alloy was put forth as a backup to U-Mo if challenges are encountered with FCCI barriers, and advanced ferritic/martensitic steels are put forth as a backup to oxide dispersion strengthened steels if swaging and welding are found unworkable.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Advanced Fuels Campaign Execution Plan

The Advanced Fuels Campaign (AFC) Execution Plan outlines the strategy, mission, scope, near-term and long-term goals, structure, and organization associated with nuclear fuels and materials research, development, and demonstration activities within the Department of Energy’s (DOE) Nuclear Fuel Cycle and Supply Chain (NFCSC) program. NFCSC has been given responsibility to identify and mature advanced fuel technologies for the DOE using a science-based approach, focused on developing a fundamental understanding of nuclear fuels and materials to drive development of integrated nuclear fuel and materials technology. This science-based approach combines theory, experiments, and multiscale modeling and simulation to achieve a predictive understanding of relevant behaviors ranging from fuel fabrication processes (and their resulting fuel microstructures) through fuel/cladding performance under irradiation (in contrast to more empirical, observation-based approaches frequently used in fuel performance modeling and fuel qualification). The traditional scope of AFC includes the evaluation and development of multiple fuel forms to support two fuel cycle options: once-through and full recycle. The word “fuel” is used generically to include conventional fuels, transmutation targets, and any associated cladding or duct materials. The once-through fuel cycle addresses advanced light water reactor fuels with enhanced performance, extended burnup, and reduced waste generation. In fiscal year (FY) 2012, AFC’s scope expanded to include research, development, and demonstration (RD&D) for light water reactor (LWR) fuels with enhanced accident tolerance. Fuel fabrication activities include the development of innovative methods to enhance process efficiencies, reduce waste, and improve control over as-fabricated fuel microstructural properties to achieve desired in-reactor performance. Using modern modeling and simulation approaches, the objective is to predict fresh fuel properties given the feedstock characteristics and fabrication process parameters. The performance-related activities include small-scale, in-reactor, and out-of-reactor phenomenological testing (distinct from, but synergistic with, integral prototypic testing) and extensive, quantitative characterization (focusing on characterization of fuel and cladding materials at the scale of microstructure) both before and after testing. Larger-scale, prototypic experiments are conducted in concert with phenomenological testing to drive a Fuel Development and Qualification program, incorporating a fundamental understanding of fuel behavior performance characteristics. Then, using the tools developed under the productive science-based approach, fuels will be optimized to meet specific performance requirements, thereby minimizing the need to repeatedly perform large-scale, integral experiments over a wide parametric range as a means of experimental exploration. Two significant initiatives are underway within AFC. First, a gap analysis completed in early FY 2019 identified critical irradiation testing needs that are lacking within the national light water reactor (LWR) fuels testbed since the shutdown of the Halden Reactor in 2018. The identified gaps are for instrumented, prototypic testing of LWR fuels, especially under boiling water reactor conditions, ramp conditions, and conditions leading to fuel failure; these needs exist for supporting current LWR fuels and their possible extension to higher burnups, but are especially urgent relative to near-term development and qualification of accident-tolerant fuels. Recommendations that resulted from the Halden Gap Analysis focused on enhancements at Advanced Test Reactor (ATR) and Transient Reactor Test Facility (TREAT) to fill gaps in testing capabilities relative to these needs. Second, a concerted effort to develop and demonstrate a systematic approach to accelerating the development, testing, and qualification of new fuel systems has been initiated. This is highlighted by a test strategy that combines the considerable advances in multiscale, mechanistic fuel modeling of recent years with a MiniFuel separate effects test program in the High Flux Isotope Reactor (HFIR) and a Fission Accelerated Steady-state Testing (FAST) semi-integral accelerated test program in ATR. This approach is being tested/demonstrated using the metallic fuel system, but if successful it is expected to be extensible to multiple fuel types and diverse applications. This document includes an overview of the NFCSC program, a definition of science-based development of nuclear fuels, near-term goals for Advanced LWR fuels (ALFs), and longer-term goals for Advanced Reactor Fuels (ARFs) RD&D. This includes the activities that will be conducted to achieve success toward the grand challenge, as well as the goals and milestones to be achieved over the next few decades of research and development. Long-term goals are based on the DOE Office of Nuclear Energ

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Advanced Fuels Campaign Execution Plan

The Advanced Fuels Campaign (AFC) Execution Plan outlines the strategy, mission, scope, near-term and long-term goals, structure, and organization associated with nuclear fuels and materials research, development, and demonstration activities within the Department of Energy’s (DOE) Nuclear Fuel Cycle and Supply Chain (NFCSC) program. NFCSC has been given responsibility to identify and mature advanced fuel technologies for the DOE using a science-based approach, focused on developing a fundamental understanding of nuclear fuels and materials to drive development of integrated nuclear fuel and materials technology. This science-based approach combines theory, experiments, and multiscale modeling and simulation to achieve a predictive understanding of relevant behaviors ranging from fuel fabrication processes (and their resulting fuel microstructures) through fuel/cladding performance under irradiation (in contrast to more empirical, observation-based approaches frequently used in fuel performance modeling and fuel qualification). The traditional scope of AFC includes the evaluation and development of multiple fuel forms to support two fuel cycle options: once-through and full recycle. The word “fuel” is used generically to include conventional fuels, transmutation targets, and any associated cladding or duct materials. The once-through fuel cycle addresses advanced light water reactor fuels with enhanced performance, extended burnup, and reduced waste generation. In fiscal year (FY) 2012, AFC’s scope expanded to include research, development, and demonstration (RD&D) for light water reactor (LWR) fuels with enhanced accident tolerance. Fuel fabrication activities include the development of innovative methods to enhance process efficiencies, reduce waste, and improve control over as-fabricated fuel microstructural properties to achieve desired in-reactor performance. Using modern modeling and simulation approaches, the objective is to predict fresh fuel properties given the feedstock characteristics and fabrication process parameters. The performance-related activities include small-scale, in-reactor, and out-of-reactor phenomenological testing (distinct from, but synergistic with, integral prototypic testing) and extensive, quantitative characterization (focusing on characterization of fuel and cladding materials at the scale of microstructure) both before and after testing. Larger-scale, prototypic experiments are conducted in concert with phenomenological testing to drive a Fuel Development and Qualification program, incorporating a fundamental understanding of fuel behavior performance characteristics. Then, using the tools developed under the productive science-based approach, fuels will be optimized to meet specific performance requirements, thereby minimizing the need to repeatedly perform large-scale, integral experiments over a wide parametric range as a means of experimental exploration. Two significant initiatives are underway within AFC. First, a gap analysis completed in early FY 2019 identified critical irradiation testing needs that are lacking within the national light water reactor (LWR) fuels testbed since the shutdown of the Halden Reactor in 2018. The identified gaps are for instrumented, prototypic testing of LWR fuels, especially under boiling water reactor conditions, ramp conditions, and conditions leading to fuel failure; these needs exist for supporting current LWR fuels and their possible extension to higher burnups, but are especially urgent relative to near-term development and qualification of accident-tolerant fuels. Recommendations that resulted from the Halden Gap Analysis focused on enhancements at Advanced Test Reactor (ATR) and Transient Reactor Test Facility (TREAT) to fill gaps in testing capabilities relative to these needs. Second, a concerted effort to develop and demonstrate a systematic approach to accelerating the development, testing, and qualification of new fuel systems has been initiated. This is highlighted by a test strategy that combines the considerable advances in multiscale, mechanistic fuel modeling of recent years with a MiniFuel separate effects test program in the High Flux Isotope Reactor (HFIR) and a Fission Accelerated Steady-state Testing (FAST) semi-integral accelerated test program in ATR. This approach is being tested/demonstrated using the metallic fuel system, but if successful it is expected to be extensible to multiple fuel types and diverse applications. This document includes an overview of the NFCSC program, a definition of science-based development of nuclear fuels, near-term goals for Advanced LWR fuels (ALFs), and longer-term goals for Advanced Reactor Fuels (ARFs) RD&D. This includes the activities that will be conducted to achieve success toward the grand challenge, as well as the goals and milestones to be achieved over the next few decades of research and development. Long-term goals are based on the DOE Office of Nuclear Energ

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Interfacial Analysis of Blister Formation in U-10Mo Mini-Plates

A thorough investigation of potential failure mechanisms builds confidence in the performance of monolithic U-10wt%Mo (U-10Mo) fuel plates. The lowenriched uranium (LEU) fuel system is currently undergoing qualification as a high U-density fuel that can be used to convert United States high-performance research reactors from high-enriched uranium (HEU) operation. This will require establishing fuel operational limits such that fission products and a coolable geometry are retained, even during off-normal reactor operation conditions [1]. Such off-normal conditions can subject the fuel plates to temperatures where the internal pressure of precipitated fission gasses result in a permanent deformed, raised area of the cladding, referred to as a blister. These blisters can reduce the local coolability of a fuel plate and can even close coolant channels of a fuel assembly, so blistered plates are considered failed regardless of whether the fuel is truly breached. Historically, a marginto- failure is established through out-of-pile blister threshold testing of irradiated fuel plates. This is accomplished by incrementally heating irradiated fuel plates until blisters are observed. This reveals the temperature threshold that would have resulted in a blister if a plate experienced them at those irradiation conditions [2]. While the blister testing itself reveals the temperatures at which the cladding mechanical integrity was exceeded, a more thorough investigation of the interface evolution in proximity to formed blisters may reveal mechanisms as to the blister formation and retention of fission gases. Previous studies have explored potential underlying mechanisms in historical plates that may have been close to blistering [3]; however, this work is the first exploration of blister tested irradiated plates, fabricated by a commercial vendor—another requirement for qualification of the fuel system [1]. The Mini-plate 1 (MP-1) experiment was the first in a series of irradiation and post-irradiation examination (PIE) campaigns to qualify the U-10Mo monolithic fuel system. It consisted of commercially fabricated 25.4×101.5 mm Al-clad mini-plates with a monolithic U-10Mo foil coated in a Zr diffusion barrier. The primary MP-1 PIE campaign was previously completed. Among the suit of examinations was a blister testing campaign, where plates were incrementally annealed in 25°C increments until blisters were observed or a maximum temperature of 550°C was reached [4]. The previously blistered plates from this campaign were revisited in this work.

25228↗

DOE OSTI2025

Device for steam cladding oxidation testing at TREAT

To compare the chemical degradation of conventional zirconium alloy (Zry) cladding to advance silicon carbide (SiC) cladding in a post loss of coolant accident (LOCA) environment, new nuclear testing capabilities are necessary. The Transient Reactor Test (TREAT) Facility at Idaho National Laboratory (INL) has matured its transient fuel testing capabilities since its 2017 restart. The most recent experiment architecture is the Transient Water Irradiation System in TREAT (TWIST), which is designed to support qualification of accident tolerant fuels in light water reactors. INL has designed and analyzed a natural circulation steam flow modification for TWIST to produce prototypic conditions of cladding oxidation. The in-situ device will be electrically heated to drive natural circulation. Moreover, the SiC cladding requires heating above 1700 °C to observe failure, thus internal prototypic nuclear heating with radiation effects will be used. Thermal hydraulic analysis with RELAP5-3D (Reactor Excursion and Leak Analysis Program) estimated steam fluxes greater than 50 mg cm −2 s −1 can be achieved. These fluxes are adequate to test Zry cladding according to draft regulatory guides and to test SiC cladding according to past experiments.

Oxidation↗

DOE OSTI2019

Size effects on thermo-mechanical performance of U-10Mo monolithic fuel plates

Monolithic fuel is a fuel form that is considered for the conversion of high performance research reactors. This plate-type fuel consists of a high density U-Mo fuel in monolithic form that is sandwiched between zirconium diffusion barriers, and encapsulated in an aluminum cladding. To date, large number of plates have been irradiated with satisfactory perforamce. The program is now moving into the qualification phase, a predecessor to the timely conversion of the target reactors. It must be shown that the fuel system meets the safety standards and performs well in reactor. The requirement to satisfactory irradiation performance under normal operating conditions is primarily demonstrated by a successful testing. Since each reactor employs distinct fuel plate geometries for various consideration with unique plate design features and attributes, a single “generic” plate geometry capturing all of the extremities is not achievable. Furthermore, testing all these geometric and irradiation parameters on a large size plate is not practical. Therefore, a smaller, “down-scaled” versions of fuel plates, are often employed for experimental purposes. This limitation consequently requires much more cautious performance evaluations, as thermal and mechanical response of a plate with certain geometry may not be representative for a plate with a different geometry. To investigate if plate size has any effects on irradiation performance, the plates with various geometric dimensions were parametrically evaluated. In particular, length and width of the plates were varied between the bounding values. Temperature, deformation, stress values were comparatively evaluated. The results have indicated that effects of geometric ratios and plate size variations in length and width directions are insignificant. However, wider plates could become more prone to a warping-type deformation, if there are nonlinearities.

42 ENGINEERING↗

DOE OSTI2019

Size effects on thermo-mechanical performance of U-10Mo monolithic fuel plates

Monolithic fuel is a fuel form that is considered for the conversion of high performance research reactors. This plate-type fuel consists of a high density U-Mo fuel in monolithic form that is sandwiched between zirconium diffusion barriers, and encapsulated in an aluminum cladding. To date, large number of plates have been irradiated with satisfactory perforamce. The program is now moving into the qualification phase, a predecessor to the timely conversion of the target reactors. It must be shown that the fuel system meets the safety standards and performs well in reactor. The requirement to satisfactory irradiation performance under normal operating conditions is primarily demonstrated by a successful testing. Since each reactor employs distinct fuel plate geometries for various consideration with unique plate design features and attributes, a single “generic” plate geometry capturing all of the extremities is not achievable. Furthermore, testing all these geometric and irradiation parameters on a large size plate is not practical. Therefore, a smaller, “down-scaled” versions of fuel plates, are often employed for experimental purposes. This limitation consequently requires much more cautious performance evaluations, as thermal and mechanical response of a plate with certain geometry may not be representative for a plate with a different geometry. To investigate if plate size has any effects on irradiation performance, the plates with various geometric dimensions were parametrically evaluated. In particular, length and width of the plates were varied between the bounding values. Temperature, deformation, stress values were comparatively evaluated. The results have indicated that effects of geometric ratios and plate size variations in length and width directions are insignificant. However, wider plates could become more prone to a warping-type deformation, if there are nonlinearities.

42 ENGINEERING↗

DOE OSTI2019

Effects of Plate Curvature on Thermo-Mechanical Performance of U-10Mo Monolithic Fuel Plates

Monolithic fuel is a candidate fuel form being considered for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo fuel in a monolithic form that is sandwiched between zirconium diffusion barriers, and encapsulated in an aluminum cladding. To date, large number of plates have been irradiated with satisfactory performance. The program is now moving into the qualification phase, a predecessor to the timely conversion of the target reactors. Since each reactor employs distinct fuel plate geometries for various consideration, resulting nearly 50 distinct plate geometries with unique plate design features, a single “generic” plate geometry capturing all of the extremities is not achievable. This limitation consequently requires much more cautious performance evaluations, as thermal and mechanical response of a plate with certain geometry may not be representative for a plate with a different geometry. To evaluate the performance of the plates for various geometric parameters, parametric sensitives studies have been employed. One of the important geometric parameters may have potential effects on the performance is the plate curvature. In this study, curved-plates were parametrically simulated to investigate if this geometric parameter has any effects on overall performance, In particular, radius of curvatures of the plates were varied between the bounding values, and the plates were simulated for comparable irradiation histories. The resulted temperature, deformation, stress-strain results were comparatively evaluated. The results have indicated that preferential deformations occur. This consequently caused shifting of plate centerline on curved plates. The magnitude of centerline shifts increased with increasing plate curvatures.

42 ENGINEERING↗

DOE OSTI2019

Effects of Plate Curvature on Thermo-Mechanical Performance of U-10Mo Monolithic Fuel Plates

Monolithic fuel is a candidate fuel form being considered for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo fuel in a monolithic form that is sandwiched between zirconium diffusion barriers, and encapsulated in an aluminum cladding. To date, large number of plates have been irradiated with satisfactory performance. The program is now moving into the qualification phase, a predecessor to the timely conversion of the target reactors. Since each reactor employs distinct fuel plate geometries for various consideration, resulting nearly 50 distinct plate geometries with unique plate design features, a single “generic” plate geometry capturing all of the extremities is not achievable. This limitation consequently requires much more cautious performance evaluations, as thermal and mechanical response of a plate with certain geometry may not be representative for a plate with a different geometry. To evaluate the performance of the plates for various geometric parameters, parametric sensitives studies have been employed. One of the important geometric parameters may have potential effects on the performance is the plate curvature. In this study, curved-plates were parametrically simulated to investigate if this geometric parameter has any effects on overall performance, In particular, radius of curvatures of the plates were varied between the bounding values, and the plates were simulated for comparable irradiation histories. The resulted temperature, deformation, stress-strain results were comparatively evaluated. The results have indicated that preferential deformations occur. This consequently caused shifting of plate centerline on curved plates. The magnitude of centerline shifts increased with increasing plate curvatures.

42 ENGINEERING↗

DOE OSTI2023

An efficient instance segmentation approach for studying fission gas bubbles in irradiated metallic nuclear fuel

Abstract Gaseous fission products from nuclear fission reactions tend to form fission gas bubbles of various shapes and sizes inside nuclear fuel. The behavior of fission gas bubbles dictates nuclear fuel performances, such as fission gas release, grain growth, swelling, and fuel cladding mechanical interaction. Although mechanical understanding of the overall evolution behavior of fission gas bubbles is well known, lacking the quantitative data and high-level correlation between burnup/temperature and microstructure evolution blocks the development of predictive models and reduces the possibility of accelerating the qualification for new fuel forms. Historical characterization of fission gas bubbles in irradiated nuclear fuel relied on a simple threshold method working on low-resolution optical microscopy images. Advanced characterization of fission gas bubbles using scanning electron microscopic images reveals unprecedented details and extensive morphological data, which strains the effectiveness of conventional methods. This paper proposes a hybrid framework, based on digital image processing and deep learning models, to efficiently detect and classify fission gas bubbles from scanning electron microscopic images. The developed bubble annotation tool used a multitask deep learning network that integrates U-Net and ResNet to accomplish instance-level bubble segmentation. With limited annotated data, the model achieves a recall ratio of more than 90%, a leap forward compared to the threshold method. The model has the capability to identify fission gas bubbles with and without lanthanides to better understand the movement of lanthanide fission products and fuel cladding chemical interaction. Lastly, the deep learning model is versatile and applicable to the micro-structure segmentation of similar materials.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Thermo-physical Properties of U-10Mo Monolithic Fuel

Monolithic fuel is a candidate fuel form that is being considered for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo fuel in a monolithic form that is sandwiched between zirconium diffusion barriers and encapsulated in an aluminum cladding. To date, many plates were irradiated with a satisfactory irradiation performance, demonstrating that the conceptual design works. The program is now moving to the qualification phase, a predecessor to the timely conversion of the target reactors. To qualify this fuel system, the program must show that the fuel plates have predictable behavior, meet the safety standards, and perform well in reactors. The requirement of a satisfactory irradiation performance under normal operating conditions is primarily demonstrated by a successful testing. To demonstrate that the fuel system has a predictable behavior, the several key material properties should be quantified accurately since these properties are needed to estimate the thermal and mechanical behavior of the fuel system. Although, there is a large set of thermophysical property data available for unirradiated material, the property data for irradiated fuel is scarce. Since irradiation causes drastic effects in material, a significant change in material properties occurs. Consequently, using representative degradation models becomes essential for accurate performance assessments. This work examines thermal conductivity of U-10Mo, by evaluating recent experimental data from the literature and available theoretical models. The study has discovered inconsistencies in the literature data, revealing that previously developed theoretical models fail to predict the thermal conductivity of irradiated fuel.

42 ENGINEERING↗

DOE OSTI2013

KJRR-FAI Status Report of Conceptual Design Activities

The Korea Atomic Energy Research Institute has initiated the Ki-Jang Research Reactor (KJRR) project to construct a new dedicated radio-isotope production facility in the KiJang province of South Korea. The KJRR will employ a uranium-molybdenum dispersion plate-type fuel clad in aluminum. The KJRR fuel assembly design will undergo irradiation in the Advanced Test Reactor (ATR) as part of the regulatory qualification of the fuel. The Idaho National Laboratory performed a multi-disciplined conceptual design effort and found that one full-size KJRR fuel assembly can be irradiated in the ATR’s north east flux trap. The analyses accomplished during the conceptual design phase are sufficient to prove viability of the overall design and irradiation campaign. Requirements for fission power can be met. The desired burnup can be achieved well within 15% depending on reactor operating availability. Mechanical design and structural analysis show that structural integrity of the irradiation test is maintained. It is recommended that future detailed design efforts be based on the concept described in this report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗