Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Finite element models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Approximating a finite element model of a hybrid deployable truss by a discrete mass model

The NASTRAN finite element model of the MSFC/hybrid deployable truss is approximated by a model consisting of four bodies serially connected by a spring hinge suspension. The truss is decomposed into four serially connected modules determining the total mass and rotational inertias for a rigid body with its mass center on the axis of the truss for each module. A five-body cantilever truss model is developed along with an undamped form of this model. Spring coefficient values are generated to match eigenvalues of the latter model with those of the NASTRAN model. Damping coefficients are then determined that provide n percent of critical damping for the model.

Chichester, F. D.↗
NASA NTRS1980

Finite element models of the space shuttle main engine

Finite element models were developed as input to dynamic simulations of the high pressure fuel turbopump (HPFTP), the high pressure oxidizer turbopump (HPOTP), and the space shuttle main engine (SSME). Descriptions are provided for the five basic finite element models: HPFTP rotor, HPFTP case, HPOTP rotor, HPOTP case, and SSME (excluding turbopumps). Modal results are presented for the HPFTP rotor, HPFTP case, HPOTP rotor, coupled HPFTP rotor and case, HPOTP case, coupled HPOTP rotor and case, SSME (excluding turbopumps), and SSME (including turbopumps). Results for the SSME (including turbopumps) model are compared to data from a SSME HPOTP modal survey.

Muller, G. R.↗
NASA NTRS1988

On the analytical treatment of impact in finite element modeling

Two simplified impact models which could be used in conjunction with finite element modeling of impacted structures are considered. The two methods are: a previously developed localized finite element impulse-momentum procedure for nondissipative impacts, and a simple gap element consisting of a parallel linear spring and damper useful in dissipative impacts. Results are presented for axial impact of an initially stationary rod. Impulse-momentum theory used in conjunction with finite element modeling was found to result in energy variations unrelated to physical behavior; these variations are reduced as the finite element model is refined.

Jeffrey, Glenda L.↗
NASA NTRS1975

Shear-flexible finite-element models of laminated composite plates and shells

Several finite-element models are applied to the linear static, stability, and vibration analysis of laminated composite plates and shells. The study is based on linear shallow-shell theory, with the effects of shear deformation, anisotropic material behavior, and bending-extensional coupling included. Both stiffness (displacement) and mixed finite-element models are considered. Discussion is focused on the effects of shear deformation and anisotropic material behavior on the accuracy and convergence of different finite-element models. Numerical studies are presented which show the effects of increasing the order of the approximating polynomials, adding internal degrees of freedom, and using derivatives of generalized displacements as nodal parameters.

Noor, A. K.↗
NASA NTRS1987

Integration of finite element modeling with solid modeling through a dynamic interface

Finite element modeling is dominated by geometric modeling type operations. Therefore, an effective interface to geometric modeling requires access to both the model and the modeling functionality used to create it. The use of a dynamic interface that addresses these needs through the use of boundary data structures and geometric operators is discussed.

Shephard, Mark S.↗
NASA NTRS1994

Development of a nondestructive vibration technique for bond assessment of Space Shuttle tiles

This final report describes the achievements of the above titled project. The project is funded by NASA-KSC (Grant No. NAG 10-0117) for the period of 1 Jan. to 31 Dec. 1993. The purpose of this project was to develop a nondestructive, noncontact technique based on 'vibration signature' of tile systems to quantify the bond conditions of the thermal protection system) tiles of Space Shuttle orbiters. The technique uses a laser rapid scan system, modal measurements, and finite element modeling. Finite element models were developed for tiles bonded to both clamped and deformable integrated skin-stringer orbiter mid-fuselage. Results showed that the size and location of a disbonded tile can be determined from frequency and mode shape information. Moreover, a frequency response survey was used to quickly identify the disbonded tiles. The finite element results were compared with experimentally determined frequency responses of a 17-tile test panel, where a rapidscan laser system was employed. An excellent degree of correlation between the mathematical simulation and experimental results was realized. An inverse solution for single-tile assemblies was also derived and is being implemented into a computer program that can interact with the modal testing software. The output of the program displays the size and location of disbond. This program has been tested with simulated input (i.e., finite element data), and excellent agreement between predicted and simulated disbonds was shown. Finally, laser vibration imaging and acoustic emission techniques were shown to be well suited for detecting and monitoring the progressive damage in Graphite/Epoxy composite materials.

Moslehy, Faissal A.↗
NASA NTRS1991

Use of system identification techniques for improving airframe finite element models using test data

A method for using system identification techniques to improve airframe finite element models was developed and demonstrated. The method uses linear sensitivity matrices to relate changes in selected physical parameters to changes in total system matrices. The values for these physical parameters were determined using constrained optimization with singular value decomposition. The method was confirmed using both simple and complex finite element models for which pseudo-experimental data was synthesized directly from the finite element model. The method was then applied to a real airframe model which incorporated all the complexities and details of a large finite element model and for which extensive test data was available. The method was shown to work, and the differences between the identified model and the measured results were considered satisfactory.

Hanagud, Sathya V.↗
NASA NTRS1993

Use of system identification techniques for improving airframe finite element models using test data

A method for using system identification techniques to improve airframe finite element models using test data was developed and demonstrated. The method uses linear sensitivity matrices to relate changes in selected physical parameters to changes in the total system matrices. The values for these physical parameters were determined using constrained optimization with singular value decomposition. The method was confirmed using both simple and complex finite element models for which pseudo-experimental data was synthesized directly from the finite element model. The method was then applied to a real airframe model which incorporated all of the complexities and details of a large finite element model and for which extensive test data was available. The method was shown to work, and the differences between the identified model and the measured results were considered satisfactory.

Hanagud, Sathya V.↗
NASA NTRS1991

Use of system identification techniques for improving airframe finite element models using test data

A method for using system identification techniques to improve airframe finite element models using test data has been developed and demonstrated. The method uses linear sensitivity matrices to relate changes in selected physical parameters to changes in the total system matrices. The values for these physical parameters were determined using constrained optimization with singular value decomposition. The method was confirmed using both simple and complex finite element models for which pseudo-experimental data was synthesized directly from the finite element model. The method was then applied to a real airframe model which incorporated all of the complexities and details of a large finite element model and for which extensive test data was available. The method was shown to work, and the differences between the identified model and the measured results were considered satisfactory.

Hanagud, Sathya V.↗
NASA NTRS2010

Finite Element Models and Properties of a Stiffened Floor-Equipped Composite Cylinder

Finite element models were developed of a floor-equipped, frame and stringer stiffened composite cylinder including a coarse finite element model of the structural components, a coarse finite element model of the acoustic cavities above and below the beam-supported plywood floor, and two dense models consisting of only the structural components. The report summarizes the geometry, the element properties, the material and mechanical properties, the beam cross-section characteristics, the beam element representations and the boundary conditions of the composite cylinder models. The expressions used to calculate the group speeds for the cylinder components are presented.

Grosveld, Ferdinand W.↗
NASA NTRS1999

Non-Linear Finite Element Modeling of THUNDER Piezoelectric Actuators

A NASTRAN non-linear finite element model has been developed for predicting the dome heights of THUNDER (THin Layer UNimorph Ferroelectric DrivER) piezoelectric actuators. To analytically validate the finite element model, a comparison was made with a non-linear plate solution using Von Karmen's approximation. A 500 volt input was used to examine the actuator deformation. The NASTRAN finite element model was also compared with experimental results. Four groups of specimens were fabricated and tested. Four different input voltages, which included 120, 160, 200, and 240 Vp-p with a 0 volts offset, were used for this comparison.

Taleghani, Barmac K.↗
DOE OSTI2026

Comparative analysis of plasticity-based GND density estimation methods in crystal plasticity finite element models

In crystal plasticity finite element (CPFE) simulations, accurately quantifying geometrically necessary dislocations (GNDs) is critical for capturing strain gradients in polycrystals. We compare different methods for quantifying GNDs, all of which originate from the Nye tensor, which is computed as the curl of the plastic deformation gradient. The projection technique directly decomposes the Nye tensor onto individual screw and edge dislocation components to compute GNDs. This approach requires converting a nine-component Nye tensor into densities for a larger number of dislocation systems, a fundamentally underdetermined (non-unique) process, which is resolved using L2 minimization. In contrast, when employing CPFE analysis, one could directly compute dislocation densities on each slip system using shear gradients. Projection and slip gradient methods are compared with respect to their prediction of GNDs with changing grain size, strain, and grain neighborhoods, including multigrain junctions. Although these techniques match analytical GND densities for single slip, single crystal deformation, and are consistent with anticipated overall GND trends, we find that the GND densities from projection techniques are significantly lower than those predicted from CPFE-based slip gradients in polycrystals. A suggested improvement of only using the active dislocation systems in the projection technique almost entirely resolved this mismatch.

Crystal plasticity↗
NASA NTRS2000

Real-time simulation of dynamically deformable finite element models using modal analysis and spectral Lanczos decomposition methods

We present two efficient methods for simulating real-time behavior of a dynamically deformable 3D object modeled by finite element equations. The first method is based on modal analysis, which uses the most significant vibration modes of the object to compute the deformations in real-time for applied forces. The second method uses the spectral Lanczos decomposition to obtain the explicit solutions of the finite element equations.

medical↗
NASA NTRS2000

Finite-Element Modeling of 3C-SiC Membranes

Finite-element modeling (FEM) of 3C-SiC thin-film membranes on Si substrates was used to determine the residual stress and center deflection with applied pressure. The anisotropic, three-dimensional model includes the entire 3C-SiC membrane and Si substrate with appropriate material properties and boundary conditions. Residual stress due to the thermal-expansion-coefficient mismatch between the3C-SiC film and Si substrate was included in the model. Both before-and after-etching, residual stresses were calculated. In-plane membrane stress and normal deflection with applied pressure were also calculated. FEM results predict a tensile residual stress fo 259 MPa in the 3C-SiC membrane before etching. This decreases to 247 MPa after etching the substrate below the membrane. The residual stress experimentally measured on sample made at Case Western Reserve University was 280 MPa on post-etched membranes. This is excellent agreement when an additional 30-40 MPa of residual stress to account for lattice mismatch is added to the FEM results.

DeAnna, R. G.↗
NASA NTRS1990

Development and application of a technique for reducing airframe finite element models for dynamics analysis

A computational procedure for the reduction of large finite element models was developed. This procedure is used to obtain a significantly reduced model while retaining the essential global dynamic characteristics of the full-size model. This reduction procedure is applied to the airframe finite element model of AH-64A Attack Helicopter. The resulting reduced model is then validated by application to a vibration reduction study.

Hashemi-Kia, Mostafa↗
NASA NTRS1982

Application of a systematic finite-element model modification technique to dynamic analysis of structures

A systematic finite-element model modification technique has been applied to two small problems and a model of the main wing box of a research drone aircraft. The procedure determines the sensitivity of the eigenvalues and eigenvector components to specific structural changes, calculates the required changes and modifies the finite-element model. Good results were obtained where large stiffness modifications were required to satisfy large eigenvalue changes. Sensitivity matrix conditioning problems required the development of techniques to insure existence of a solution and accelerate its convergence. A method is proposed to assist the analyst in selecting stiffness parameters for modification.

Robinson, J. C.↗
NASA NTRS1987

Dynamic and thermal response finite element models of multi-body space structural configurations

Presented is structural dynamics modeling of two multibody space structural configurations. The first configuration is a generic space station model of a cylindrical habitation module, two solar array panels, radiator panel, and central connecting tube. The second is a 15-m hoop-column antenna. Discussed is the special joint elimination sequence used for these large finite element models, so that eigenvalues could be extracted. The generic space station model aided test configuration design and analysis/test data correlation. The model consisted of six finite element models, one of each substructure and one of all substructures as a system. Static analysis and tests at the substructure level fine-tuned the finite element models. The 15-m hoop-column antenna is a truss column and structural ring interconnected with tension stabilizing cables. To the cables, pretensioned mesh membrane elements were attached to form four parabolic shaped antennae, one per quadrant. Imposing thermal preloads in the cables and mesh elements produced pretension in the finite element model. Thermal preload variation in the 96 control cables was adjusted to maintain antenna shape within the required tolerance and to give pointing accuracy.

Edighoffer, Harold H.↗