Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FUEL PINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Fuel pin zoning to improve the accuracy of the palisades spent fuel pool criticality analysis

Most PWR spent fuel pool criticality analyses assume that the burnup is uniformly distributed among the fuel pins in the assembly. This assumption is accurate for PWR cores that have the typical small inter-assembly gap. The Palisades reactor core, however, is different in that it uses cruciform control rods in between fuel assemblies. Every interior assembly has two sides having a wide water gap and two sides having a narrow water gap. After depleting under these conditions, the pins near the wide water gap will have a higher burnup than the pins in the center. If the burnup is distributed uniformly among the pins, the resulting k calculation will be conservative but excessively so. The excess conservatism was found to be on the order of 1% in k. For this analysis, SCALE 6.1 depletion with TRITON is used followed by the CSAS5 module for the Palisades pool analysis. Several burnup zoning arrangements (uniform enrichment) were investigated ranging from 3 zones to as many as 19 zones. The 19 zone analysis agreed well with a CASMO analysis where every pin was its own depletion zone. It was found that 8 fuel zones gave essentially the same result as 19 zones with less complexity. The depletion calculation using 8 fuel zones instead of a single zone is more complicated but the resulting k calculation no longer has the excessive conservatism seen in a one zone model. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of Subdivided Versus Full-Length Fuel Pin Burnup in the ATF-2 Safety Analysis

The Accident Tolerant Fuels (ATF) campaign, under the Fuel Cycle Research and Development (FCRD) Advanced Fuels program, was developed after the Fukushima Daiichi Nuclear Power Plant disaster in 2011. Under ATF, fuel and cladding concepts are to be developed and tested that may more readily withstand an accident similar to the one that occurred at Fukushima Daiichi. ATF is a combination of industry, universities, and national laboratories in an effort to develop advanced accident tolerant cladding and fuel concepts. The end goal of the ATF program is to insert a lead test rod (LTR) or lead test assembly (LTA) into an operating commercial power light water reactor by 2022. In order to meet this 2022 insertion goal, ATF is split into three separate phases: ATF-1, ATF-2, and ATF-3. The first phase of the ATF program, ATF-1, is the concept feasibility study and early irradiation testing. Feasibility, fabrication, and out-of-pile testing are happening at universities and laboratories all over the United States. Irradiation testing of these concepts is happening at the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). Early irradiation testing involves testing clad and/or fuel in drop-in capsules in the ATR. Currently, these capsules are in the relatively low-flux positions in the ATR, but some newer concepts and concepts that require higher burnup will be moved to the higher-flux positions later on during irradiation. Currently, Oak Ridge National Laboratory (ORNL), Westinghouse Electric Company, Areva, and General Electric (GE) have inserted capsules for ATF-1, although more concepts are planned. The second phase of ATF, ATF-2, is the focus of this paper. ATF-2 is the loop testing of fuel pins with new cladding and fuel concepts to simulate pressurized water reactor (PWR) and boiling water reactor (BWR) environments. ATF-2 will concurrently be happening at the ATR and at the Halden Reactor in Norway. The ATF-2 irradiation at the ATR will only simulate a PWR environment. ATF-2 will be inserted into the ATR pressurized water loop, Loop 2A, in the Center Flux Trap (CFT), where chemistry, temperature, and pressure can all be controlled separately from the primary coolant system and other loops in ATR. Loop 2A will be borated, pressurized to 2200 psi nominal, and have an average water temperature of 300 deg. C. A borated loop with fueled rodlets is extremely rare for Nuclear Energy experiments in the ATR, so ATF-2 will demonstrate new and unique capabilities for INL. ATF-3 is the testing of fresh and irradiated ATF concepts at the Transient Reactor Test (TREAT) Facility. The TREAT Reactor is planned for restart, re-establishing U.S. transient testing capabilities after nearly 20 years of non-operations. TREAT will test ATF concepts under transient conditions, such as a reactivity insertion accident. In addition to fresh fuel pins, TREAT will use from ATF2 and do transient testing on those irradiated pins. The information TREAT will provide to the vendors to support fuel licensing will be valuable, showing that these concepts do enhance the accident tolerance of the fuel in commercial reactors. (author)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Examination of T-111 clad uranium nitride fuel pins irradiated up to 13,000 hours at a clad temperature of 990 C

The examination of 27 fuel pins irradiated for up to 13,000 hours at 990 C is described. The fuel pin clad was a tantalum alloy with uranium nitride as the nuclear fuel. Two nominal fuel pin diameters were tested with a maximum burnup of 2.34 atom percent. Twenty-two fuel pins were tested for fission gas leaks; thirteen pins leaked. Clad ductility tests indicated clad embrittlement. The embrittlement is attributed to hydrogen from an n,p reaction in the fuel. Fuel swelling was burnup dependent, and the amount of fission gas release was low, generally less than 0.5 percent. No incompatibilities between fuel, liner, and clad were in evidence.

Slaby, J. G.↗

EXFILE: A program for compiling irradiation data on UN and UC fuel pins

A FORTRAN-4 computer program for handling fuel pin data is described. Its main features include standardized output, easy access for data manipulation, and tabulation of important material property data. An additional feature allows simplified preparation of input decks for a fuel swelling computer code (CYGRO-2). Data from over 300 high temperature nitride and carbide based fuel pin irradiations are listed.

Mayer, J. T.↗

Initial demonstration of automated fuel performance modeling with 1977 EBR-II metallic fuel pins using BISON code with FIPD and IMIS databases

Using the BISON fuel performance code, simulations were conducted using an automated process to read initial and operating conditions from the Fuels Irradiation and Physics Database (FIPD) and Integral Fast Reactor materials information system (IMIS) database, which contains metallic fuel data from the Experimental Breeder Reactor-II (EBR-II). This work demonstrates use of an integrated framework to access the vast majority of EBR-II experimental fuel pin data to support rapid development of fuel performance models for next-generation metallic fuel systems. With this capability, validation for fuel qualification can be performed rapidly. Between IMIS and FIPD, there is enough information to conduct 1977 unique EBR-II metallic fuel pin histories from 24 different experiments, at varying levels of detail between the two databases. Each of these histories includes a high-resolution power history, flux history, coolant channel flow rates, and coolant channel temperatures. Fission gas release (FGR), cumulative damage fraction (CDF), fuel axial swelling, cladding profilometry, and burnup were all simulated in BISON. The results were compared to post-irradiation examination (PIE) results for the initial demonstration of automated BISON modeling. BISON simulations conducted with IMIS and FIPD were in rough agreement with PIE measurements and calculations. Cladding profilometry, FGR, and fuel axial swelling were found to be in rough agreement with PIE measurements, depending on the physics used within the BISON input files. Here, the mechanical contact solver chosen was found to significantly impact axial fuel swelling and cladding strain predictions. CDF values were assessed to see whether pin failure may have been predicted (CDF ≥ 1). This work suggests that continued development of an automated tool for BISON should focus on inclusion of the Fast Flux Test Facility (FFTF) experimental data for a larger database for metallic fuel, improved physical models to better capture fuel performance, such as fuel-cladding interactions, and a more detailed comparison with available PIE data to further the BISON model development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Engineering & Microstructure Scale PIE Report on EBR-II X441A Metallic Fuel Pins for the MORPH Experiment

The objectives of this project are to increase fundamental understanding of irradiation induced metallic U-Pu-Zr fuel behavior and to obtain data needed for the development of irradiation models for metallic fuels in MARMOT. The requested metallic fuel pins are from the X441A experiment irradiated in Experimental Breeder Reactor (EBR)-II and will be provided by the PIs for the duration of the experiment. The purpose of the pins irradiated in the X441A assembly was to vary Zr composition and fuel slug diameter in order to provide data for the metallic fuel performance code “LIFEMETAL” [ANL-IFR-125]. The fuels of interest to this project are metallic fuels with several Zr compositions (in wt.%): U-19Pu-6Zr, U-19Pu-10Zr, and U-19Pu-14Zr, which were irradiated to a peak burnup of approximately 11 at.%. The cladding was the same for all three fuel pins (austenitic stainless steel D9), which allows investigation of fuel-cladding interaction (FCI) phenomena. Varying Zr content in fuel pins enables investigation of the effect of Zr on fuel restructuring and fuel-cladding compatibility. Engineering and microstructure scale PIE activities will be focused on investigation of fundamental aspect of fuel performance such as species diffusion and migration, fission product behavior, and constituent redistribution. Obtained microstructural information will be used as the basis for the development of MARMOT models of U-Pu-Zr fuel performance at the mesoscale. Experimental data obtained through this proposal will be used to provide this fundamental understanding which will serve as the foundation of the development of radiation models for U-Pu-Zr in MARMOT. It will also provide a starting point for the design of new experiments to provide data for the validation of these MARMOT models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel Pin Melting in a Fast Reactor and Melt Solidification: Simulation Using the SAFR/V1 Module of the EVKLID/V2 Integral Code

The approaches used in the SAFR/V1 module modeling the thermal destruction of fuel pins in fast reactors for calculating in integrated code EVKLID/V2 the melting of fuel pins and solidification of the formed melt are described. The enthalpy formulation of the heat-conduction equation is used. The numerical scheme used for the heat-conduction equation in performing the calculations is presented. The realized boundary conditions as well as a model of the gas gap in a fuel pin are described. The module’s capability of modeling heat propagation, including in the presence of a phase transition, is verified on the basis of analytical tests.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Assessment of Failure Mechanisms for GFR Vented Fuel Pins Using Hexoloy Cladding

A near-term vented fuel pin concept as a back-up option for the gas-cooled fast reactor (GFR) system was evaluated. This work explored the feasibility of using mixed carbide fuel (U0.85P0.15)C with off-the-shelf monolithic SiC clad in order to meet requirements for GFR fuel with an average burnup of 10%. The stress loading on the SiC cladding due to fuel swelling and thermal stress due to temperature gradient were estimated based on the data from the development of carbide fuels in the 1970’s-1980’s and the materials properties for SiC tubes. The fuel swelling at the goal burnup (10%) is expected to produce a hoop stress of approximately 32 MPa in cladding, approaching the estimated maximum allowable hoop stress (~33 MPa) for a SiC cladding reliability of 99.99%. The estimated tensile thermal stress component (~121 MPa) near the outer surface of a monolithic SiC cladding is likely to limit its application at high temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Critical and Subcritical Californium Source Driven Noise Analysis Experiments with Fresh PWR Fuels Pins

These experiments were performed in 1983 between August 1 and September 16 and used 35 operational days of critical facility time at the Babcock & Wilcox critical facility in Lynchburg, Va. These measurements were to assess the capability of the Cf source driven noise analysis method to measure the subcriticality of light water reactor fresh fuel configurations. This report documents the experiments of 1983 that were not reported at that time. These measurement with 2.459 wt. % 235 U enriched uranium oxide fresh fuel pins started at the delayed critical configuration of the fully assembled pressurized water reactor (PWR) core configuration with 1511 parts per million (ppm) natural boron (19.8 wt. % 10 B) in the water. This was a cylindrical configuration of 4961 fuel pins. After the initial measurements at delayed criticality, subcritical measurements by the Cf source driven noise analysis method were performed in which the number of detectors and Cf source locations were varied. Additional boron was added to the water moderator and reflector to reduce the neutron multiplication factor, with resulting boron concentrations of 1561, 1613, 1765, 1880, 2104, 2384, 2975, 3606, and 4303 ppm. After the completion of these measurements the increased, the boron concentration was returned to that at delayed critical (1511 ppm) and the reactivity was decreased by reducing the number of fuel pins in steps to 3713, 2553, 1281, 749, and 333 fuel pins and then to that (289) of a s ingle square 17 x 17 pin array, corresponding to a single PW fuel element. For all measurement that started at delayed criticality and then reduced the neutron multiplication factor to various subcritical states, inverse kinetics rod drop measurements at the higher reactivities were also performed but not reported here. At all subcritical states the break frequency noise analysis data was fitted to obtain the prompt neutron decay constant. Some data presented in this report are from notes not in the logbook. The purpose of this report is to document the experimental information for the measurements performed so that a later date someone could perform the required uncertainty and calculational analyses and documentation to use these data for an International Nuclear Criticality Safety Benchmark Program (INCSBEP) or Nuclear Energy Agency (NEA) benchmark. The data from these measurements is available from the Laboratory Records Department of Oak Ridge National Laboratory and the logbook is available from INCSBEP at Idaho National Laboratory.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fabrication of fuel pin assemblies, phase 3

Five full size and eight reduced length fuel pins were fabricated for irradiation testing to evaluate design concepts for a fast spectrum lithium cooled compact space power reactor. These assemblies consisted of uranium mononitride fuel pellets encased in a T-111 (Ta-8W-2Hf) clad with a tungsten barrier separating fuel and clad. Fabrication procedures were fully qualified by process development and assembly qualification tests. Detailed specifications and procedures were written for the fabrication and assembly of prototype fuel pins.

Keeton, A. R.↗

Results of Critical Experiments on Water-Moderated Fully-Reflected 6.90% Enriched UO2 Fuel Pin Arrays with a Fuel-to-Water Volume Ratio of 0.52 [Slides]

We have completed a second set of experiments in the Seven Percent Critical Experiment (7uPCX). We completed an evaluation of the experiments as criticality safety benchmark experiments. The reviews of the benchmark evaluation have been completed. The evaluation will be published in the 2013 edition of the International Handbook of Evaluated Criticality Benchmark Experiments as LEU-COMP THERM-078 (LCT078). This presentation is a brief tour of the experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fast Spectrum Experiment Fuel Pin Payload Specification for Package 9330

This specification supports work to be conducted by AREVA Federal Services under Idaho National Laboratory (INL) Subcontract No. 45559, Release 50, including Statement of Work (SOW) -11417 addressing package transportation licensing. This document provides transportation payload specification for experiment fuel pins produced in the performance of INL CRADA 13-CR-15. The payload description provided in this document will be used to obtain licensing necessary to enable transportation of unirradiated experiments in ATR Fresh Fuel Shipping Containers (FFSCs). The FFSC has a current U. S. Department of Energy (DOE) certificate, USA/9330/AF-96, revision 0, which is available on the DOE RAMPAC website or upon request from the INL or DOE. Its desired payload will consist of individual experiment fuel pins (a.k.a. rods) loaded in a FFSC’s internal fuel handling enclosure (FHE), a.k.a. internal canister. Each package and its FHE arrangements should be prepared for a payload that contains less than critical mass and is certified for ground and air transportation per NRC 10 CFR 71 and International Atomic Energy Agency (IAEA) criteria. The unirradiated experiment fuel pins are all fabricated with uranium-based fuel and ferritic-martensitic stainless steel, HT-9, cladding and end plugs. The payload may include pins with and without spacer-wires. Solid pins will have minimal amounts of sodium bonding between the fuel and inside cladding. Annular pins will contain He gas installed at atmospheric pressure (~12.7 psia). Uranium fuel will be of varying enrichments with a maximum bounding enrichment of 94% U-235. Blanket material consists of depleted uranium and zirconium of varying weight percent. Section 2 provides pin parameters for NRC 10CFR71 and IAEA evaluations. Supplemental criteria titled functional and operating requirements is intended to convey other requirements, including those that protect the payload, rather than to demonstrate package compliance with regulations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Wire-Wrapped Fuel Pin Effect of Bundle Size on Temperature Distribution for Uniform Heat Flux

A common fuel arrangement for Sodium Fast Reactors (SFR) designs are hexagonal arrays of wire wrapped fuel pins. The helically wound wires redirect coolant to neighboring subchannels and increases mixing. The increased mixing of the coolant is beneficial to heat transfer from the fuel and prevents temperature peaking in hot channels that may occur. The purpose of this study is to observe the effect of bundle size on the temperature distribution of a coolant when a constant heat flux is implemented. Bundles of 19, 37, 61, and 91 pins were modeled. The wire-wrapping on fuel pins encourages interchannel mixing. With a constant heat flux the enhanced interchannel mixing has little observable effect. The temperature distributions of the subchannels has negligible dependence on radial or angular position. The temperature distribution additionally shows negligible dependence on the bundle size. The subchannel average temperatures further illustrate the homogeneity of the temperature across the bundles. Similarly oriented subchannels differ by less than two Kelvin. The temperature distribution within a single subchannel is fairly uniform, differing by about 15 K between the wall and the bulk flow, with the exception of two hot spots. The two hot spots, however, occur in two non-geometrically accurate locations, so little analysis can be performed. To better illustrate the effect of the enhanced mixing of the wire-wrapped fuel pins, a hot pin analysis should be performed to observe how the additional, non-uniform heat is dispersed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Carbide fuel pin and capsule design for irradiations at thermionic temperatures

The design of a capsule assembly to evaluate tungsten-emitter - carbide-fuel combinations for thermionic fuel elements is presented. An inpile fuel pin evaluation program concerned with clad temperture, neutron spectrum, carbide fuel composition, fuel geometry,fuel density, and clad thickness is discussed. The capsule design was a compromise involving considerations between heat transfer, instrumentation, materials compatibility, and test location. Heat-transfer calculations were instrumental in determining the method of support of the fuel pin to minimize axial temperature variations. The capsule design was easily fabricable and utilized existing state-of-the-art experience from previous programs.

Siegel, B. L.↗

Thermal analysis of the FSP-1 fuel pin irradiation test

Thermal analysis of a pin from the FSP-1 fuels irradiation test has been completed. The purpose of the analysis was to provide predictions of fuel pin temperatures, determine the flow regime within the lithium annulus of the test assembly, and provide a standardized model for a consistent basis of comparison between pins within the test assembly. The calculations have predicted that the pin is operating at slightly above the test design temperatures and that the flow regime within the lithium annulus is a laminar buoyancy driven flow.

Lyon, William F., III↗

Conjugate Heat Transfer Modeling of Salt-Filled Fuel Pins for Stable Salt Reactor Safety Analysis

The Stable Salt Reactor (SSR) combines the proven structural design of light water reactor fuel assemblies with the inherent safety and fuel-cycle advantages of molten salt technology. In its fast reactor configuration, the SSR utilizes recycled nuclear waste as fuel, sealed within narrow salt-filled fuel pins and cooled by a surrounding liquid salt coolant. Reliable transfer of heat from the molten fuel salt through the cladding to the external coolant is essential for both reactor safety and performance. This work investigates conjugate heat transfer (CHT) in the SSR’s salt-filled fuel pins using NekRS, a high-fidelity spectral element computational fluid dynamics (CFD) solver. The analyses capture internal natural convection within the molten fuel salt and external forced convection in the coolant, under steady-state and transient operating conditions. Parametric studies evaluate how variations in reactor power and coolant flow rate influence heat transfer distributions and system response. The high-fidelity CFD results are time-averaged and post-processed for direct comparison with moderate-fidelity Reynolds-averaged Navier–Stokes (RANS) models, and for the development of reduced-order models within the SAM system code. These validated models support fast-running safety analyses of normal and off-normal transients, improving predictive capability for key safety margins. By integrating advanced CFD with system-level safety tools, this study strengthens the modeling framework for SSR design, reduces uncertainty in molten salt CHT simulations, and accelerates the engineering and licensing of next-generation nuclear reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Irradiation of three T-111 clad uranium nitride fuel pins for 8070 hours at 990 C (1815 F)

The design and successful operation of three tantalum alloy (Ta-8W-2Hf) clad uranium mononitride (UN) fuel pins irradiated for 8070 hr at 990 C (1815 F) is described. Two pin diameters having measured burnups of 0.47 and 0.90 uranium atom percent were tested. No clad failures or swelling was detected; however, postirradiation clad samples tested failed with 1 percent strain. The fuel density decrease was 2 percent, and the fission gas release was less than 0.05 percent. Isotropic fuel swelling, which averaged about 0.5 percent, was less than fuel pin assembly clearances. Thus the clad was not strained. Thermocouples with a modified hot zone operated at average temperatures to 1100 C (2012 F) without failure. Factors that influence the ability to maintain uniform clad temperature as well as the results of the heat transfer calculations are discussed.

Slaby, J. G.↗