Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FIBER STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Quality Investigation of Pultruded Carbon Fiber Panels Subjected to Four-Point Flexure via Fiber Optic Sensing

Pultruded carbon fiber-reinforced composites are attractive to the wind energy industry due to the rapid production of highly aligned unidirectional composites with enhanced fiber volume fractions and increased specific strength and stiffness. However, high volume carbon fiber manufacturing remains cost-prohibitive. This study investigates the feasibility of a pultruded low-cost textile carbon fiber-reinforced epoxy composite as a promising material in spar cap production was undertaken based on mechanical response to four-point flexure loading. As spar caps are primarily subjected to flexural loading, large-span four-point flexure was considered, and coupon testing was restricted to tensile modulus and compression strength assessment. High-resolution spatial fiber optic strain sensing was utilized to determine spatial strain distribution during four-point flexure, revealing consistent strain along the length of the part and proved to be an excellent option for process manufacturing quality examination. Additionally, holes with diameters of 2.49 mm, 5.08 mm, and 1.93 mm were drilled through the thickness of full-width parts to determine the feasibility of structural health monitoring of pultruding parts internal to wind blades via fiber optic strain sensing.

Chemistry↗
DOE OSTI2024

Epoxy Coating of Biofiber: An Effective Modifier of Biofiber Physical and Flow Properties for Improved Tensile Behavior of Biofiber-Reinforced Biocomposite

Biocomposites combine renewable, plant-based fibers with degradable polymers and are an attractive option for sustainable, lightweight, and cost-effective materials with a low carbon footprint, especially for large-scale additive manufacturing. One of the major challenges in the widespread adoption of biocomposites is that their mechanical performance is significantly inferior to that of synthetic composites. Surface treatment is a common and effective technique to improve the mechanical properties of the biofibers used in biocomposites. This study aims to investigate the physical and flow properties of surface-treated biofibers, as well as the tensile properties of their PLA-based biocomposite, to gain insights into how surface treatment changes the fiber‘s characteristics and biocomposite‘s mechanical properties. Surface treatment was created using a two-component epoxy system by reacting poly(bisphenol A-co-epichlorohydrin) glycidyl end-capped (PBG) and dicyandiamide (DICY). The treatment was tested on two different biofibers (loblolly pine and corn stover fibers) with three different PBG/DICY molar ratios (0.25, 0.5, and 2). Results showed that surface-treated fibers improved the tensile strength and Young‘s modulus of the biocomposites. Loblolly pine biocomposites from fibers treated with a PBG/DICY ratio of 0.25 exhibited the best tensile properties. The surface treatment resulted in a more loosely dispersed fiber bulk structure, as evidenced by less fiber agglomeration into smaller particle sizes, higher fiber sphericity, and lower loose bulk density. This can enhance stress distribution and the overall mechanical performance of the biocomposites. Additionally, surface-treated fibers exhibited better dynamic flow properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Strength characterization of solar-synthesized cylindrical graphite carbon–carbon composites

The present work describes a new morphology of cylindrical graphite synthesized in a unique manner by direct solar decomposition of methane and reports the mechanical properties of its manifestation in woven carbon–carbon composites. Whereas traditional carbon–carbon composites are formed via epoxy impregnation, the deposited material in the process presented here conformally follows the existing shape and orientation of individual carbon fibers. Through this process, cylindrical graphite fibers are synthesized that possess superior strength due to their graphitic layers that amalgamate into interlocked pathways between disparate fibers. Here, strength measurements, taken in tandem with Raman, XRD, and SEM, paint a picture of the shift from cloth to composite behavior via graphitization of the original substrate combined with sheets of graphene coalescing into a unified composite, with a notable improvement in elastic modulus from 0.19 to 2.66 GPa.

Carbon–carbon composite↗
DOE OSTI2024

Flax–Reinforced Vitrimer Epoxy Composites Produced via RTM

Composite laminates were produced by RTM using similar glass and flax fabrics and both vitrimer epoxy and aerospace-grade epoxy, both formulated for liquid molding. Tensile and flexural properties were measured and compared, revealing that the vitrimer composites exhibited equivalent performance in flexural strength and tensile modulus, but slightly lower performance in tensile strength relative to reference epoxy composites. In general, glass–fiber composites outperformed flax–fiber composites in tension. However, both glass and flax–fiber composites yielded roughly equivalent flexural strength and tensile modulus-to-weight ratios. Flax fabrics were recovered from composites by matrix dissolution, and a second-life laminate showed full retention of the mechanical properties relative to those produced from fresh flax. Finally, a demonstration of re-forming was undertaken, showing that simple press-forming can be used to modify the composite shape. However, re-forming to a flat configuration resulted in local fiber damage and a decrease in mechanical properties. An alternative forming method was demonstrated that resulted in less fiber damage, indicating that further refinements might lead to a viable forming and re-forming process.

Martinez, Patricio (ORCID:0000000225884389)↗
DOE OSTI2025

Advanced polymer impregnation and pyrolysis (PIP) of SiOC-based ceramic matrix composites (CMCs)

Silicon carbide (SiC) ceramic matrix composites (CMCs) are valued for their high-temperature properties, making them ideal for harsh environments. However, conventional polymer impregnation and pyrolysis (C-PIP) often result in porous composites and require numerous cycles for densification. This study introduces the advanced PIP (A-PIP) method using a crosslinked polycarbosiloxane (PCS) precursor to enhance densification efficiency. Five SiC CMCs were fabricated using C-PIP and A-PIP, with variations in fiber reinforcement and fiber coatings. A-PIP achieved up to 19 % higher density and 78 % lower porosity in 79–86 % less processing time compared to C-PIP. Moreover, SiC-SiOC composites with boron nitride-coated fibers showed significant improvements in tensile strength (11 MPa to 134 MPa) and strain at maximum strength (0.01–0.11 %), underscoring the role of weak fiber-matrix interfaces. In conclusion, these results demonstrate A-PIP's potential to produce dense, low-porosity SiC CMCs more efficiently, significantly reducing manufacturing time and costs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Use of Ionic Liquids for Hemp Fiber Degumming

Degumming or retting to remove pectin, lignin, and hemicellulose is a critical step in the production of high-quality hemp fibers. Current technologies, including traditional water or dew retting, as well as chemical, enzymatic, and physical degumming processes, have inherent environmental risks and produce fibers of varying qualities. Herein we explore the use of an ionic liquid (IL) capable of dissolving pectin, lignin, and hemicellulose, but not cellulose, in combination with different oxidating agents to degum hemp. In this study, we observed that treating raw hemp fibers with the IL choline acetate ([Cho][OAc]), alone or in combination with aqueous H 2 O 2 , led to a reduction in the gummy materials and lignin content of the resulting samples of up to 63 and 78%, respectively. More importantly, the high crystallinity and low reduction in tensile strength of the resulting fibers make these novel and relatively simple IL-based processes promising alternatives toward the sustainable preparation of hemp-based materials suitable for use in the textile industry.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Adhesion in thermomechanically processed seaweed-lignocellulosic composite materials

The increasing concerns associated with petroleum-derived polymers motivate the development of sustainable, renewably sourced alternatives. In ubiquitous applications such as structural materials for infrastructure, the built environment as well as packaging, where natural materials such as wood are used, we rely on nonrenewable and nondegradable polymers to serve as adhesives. In wood panels, such as medium density fiberboards (MDFs), formaldehyde-based resins are predominantly used to bond wood fibers and to provide strength to the materials. To further mitigate the environmental impact of construction materials, more sustainable adhesives need to be investigated. Here, in this article, we introduce Ulva seaweed as an adhesive to enable cohesion and strength in hot-pressed wood panels. Upon hot-pressing, powdered Ulva flows in between the wood particles, generating a matrix, which provides strong binding. We show that the flexural strength of Ulva-bonded wood biocomposites increases with increasing Ulva concentrations. At an Ulva concentration of 40 wt%, our composites reach an average elastic modulus of 6.1 GPa, and flexural strength of 38.2 MPa (compared to 4.7 GPa and 22.6 MPa, respectively, for pure wood compressed at the same pressing conditions). To highlight the bonding mechanisms, we performed infrared and x-ray photoelectron spectroscopy and identified indications of fatty acid mobility during hot-pressing. In addition, we demonstrate that the presence of Ulva improves other properties of the composites such as water resistance and fame retardancy. Ulva is also shown to behave as an excellent adhesive agent between two prepressed beams. Finally, we perform an in-depth analysis of the environmental impact of wood-Ulva biocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding interfacial crystallization dynamics on carbon fiber reinforced polypropylene composite manufacturing

Reinforcing polymers with discontinuous fibers improves mechanical properties, such as strength and stiffness, and in some cases achieve isotropic properties, rendering them suitable for various engineering applications. Matrix materials are generally highly engineered thermosets (e.g. crosslinked epoxies), bonded to the fiber periphery by proprietary surface and sizing chemistries. Semicrystalline thermoplastic matrices are less utilized due to poor fiber-matrix bonding resulting in inefficient interfacial load-transfer in reinforced composites. However, flexibility with melt-processing or molding conditions can be leveraged to promote non-covalent interfacial bonding between matrix and fiber via crystallization of the matrix onto fiber surface. In the present study, we utilize a co-mingle chopped carbon and isotactic polypropylene fibers to form isotropic composites, tailoring interfacial immobilized matrix or interphase morphology to optimize performance through precise control of thermal processing/molding windows. Calorimetry and optical microscopy were employed to investigate the impact of carbon fiber at various volume fractions (10, 20, and 30 %) on isotactic polypropylene crystallization and mechanical performance. Variations in mechanical properties correspond to the structural evolution of the interfacial region and are correlated to underlying microstructural attributes using wide-angle X-ray scattering, thermal analysis, and low-field nuclear magnetic resonance spectroscopy. These results provide a practical framework for the manufacturing of thermoplastic matrix composites. In conclusion, the results presented provide a guide for the strategic optimization of interphase design, showcasing tailorable tensile strengths which outperform any isotactic polypropylene carbon fiber composites previously reported in literature.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Initial assessment of alternative carbon fiber geometries for design of cost-effective compressive performance: Size effect studies

Carbon fiber provides opportunity to reduce weight in structural composites, including wind turbine blades, due to the material's superior specific stiffness and specific strength compared to alternatives. Despite these advantages, cost and compressive performance are considered weaknesses for carbon fiber products available today. Studies to produce low-cost carbon fiber alternatives, including the use of textile-derived precursor systems, have shown progress and merit through the DOE/ORNL low-cost carbon fiber initiatives. Here, this work focuses on enabling increases in compressive strength through design of the carbon fiber geometry, applicable to both textile and conventional precursor systems, while also providing opportunities to reduce carbon fiber processing costs. Fiber-resin interface and fiber alignment are among the most frequently cited factors controlling composite compressive performance. However, it is believed that there is opportunity in traditionally unexplored routes to increasing compressive strength through alteration of the carbon fiber geometry by increasing the fiber area moment of inertia and/or the fiber perimeter and interfacial area. This paper presents initial results from manufacturing carbon fiber materials to assess the impacts of carbon fiber size on tested composite compressive performance with projected neutral or even beneficial impact on fiber and composite manufacturing economics. Carbon fiber systems with increasing size illustrate a favorable correlation for compressive performance greater than predicted from a micromechanical failure model. The manufacturing and mechanical test results support the hypothesis of this work that alterations to fiber geometry can be used to produce improvements of the compressive strength of carbon fiber reinforced polymers and provide incentive for related work in designing alternative shapes to further enhance compressive performance.

42 ENGINEERING↗
DOE OSTI2024

Effects of mercerization and fiber sizing of coir fiber for utilization in polypropylene composites

The use of natural fibers as an alternative to synthetic fibers for reinforcing composites is increasing. However, the poor interfacial adhesion between natural fibers and polymer matrices limits their applications. Several approaches have been considered to improve fiber-matrix adhesion via chemical and/or physical treatment. However, the effectiveness of these treatments varies based on the type of fiber, its source, and its composition. Thus, it is imperative to understand the effectiveness of treatment conditions. In this study, we investigated the influence of alkali treatment and fiber sizing on the chemical, thermal, morphological, and mechanical properties of coir fibers and the interface between coir fiber and polypropylene matrix. Further, it was found that using a 5 wt% sodium hydroxide solution for 6 h at room temperature was the optimal treatment condition that led to an improvement in tensile strength by 58%, tensile modulus by 71%, and elongation at break by 37% compared to untreated fibers, and an increment in interfacial shear strength (IFSS) between coir fibers and polypropylene matrix by 32%. The alkali treatment removed the fiber surface impurities, made the fiber surface rough, and enhanced the fiber crystallinity. Sizing of the alkali-treated fiber led to an improvement in IFSS by 87% with no modification of the fiber’s mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A mild calcium carbonate treatment improves moisture resistance and mechanical/interfacial properties of jute and hemp fibers

Natural fibers are attractive, sustainable reinforcements, but often exhibit high moisture uptake and weak bonding with polymer matrices. In this study, jute and hemp were treated by immersion in aqueous calcium carbonate (CaCO3) suspensions (10–40?wt.%, 1.5?h, room temperature) and were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), moisture sorption testing, single-fiber tensile testing, and bundle pull-out testing. SEM showed granular CaCO3 deposition on fiber surfaces, with particulates bridging surface voids and microcracks. At 40 wt.% CaCO3, equilibrium moisture uptake decreased to ~5% (hemp) and ~3% (jute), while tensile strength increased to ~904 MPa (hemp) and ~960 MPa (jute). Apparent interfacial shear strength from pull-out testing increased up to ~1.35 MPa (hemp) and ~0.56 MPa (jute). These results indicate that CaCO3 deposition is a mild, scalable surface treatment that improves moisture resistance, fiber tensile strength, and interfacial load transfer relevant to semi-structural composite applications, including interior and secondary automotive components.

Calcium carbonate treatment↗
DOE OSTI2025

Design and Production for Maximum Structural Efficiency With Respect to Fiber Orientation With Increased Understanding of Hybrid Fiber Flow Behavior

Discontinuous fiber-reinforced thermoplastic composites have gained considerable attention in automotive, aerospace, and other industries, due to their high-rate of production combined with their ability to attain complex and intricate shapes. Among other high-rate thermoplastic manufacturing processes, injection-molding is one of the most common manufacturing methods due to fast production and high surface finishing of complex geometries. Fiber orientation in discontinuous fiber composites plays a pivotal role in determining the mechanical, electrical, and thermomechanical properties, underscoring the necessity to comprehend fiber orientation in injection molded parts. Among different fiber types, glass and carbon fibers are most common in the composite industries. The recent trend of hybrid composites comprising both glass fiber (GF) and carbon fiber (CF) is also gaining importance in the automotive industry. Hybrid fiber options allow designers to optimize the balance between glass and carbon fibers by leveraging the high durability and low cost of GF while the strength and lightweight properties of CF. Consequently, comparing the fiber oriented distribution (FOD) of injection molded composites containing GF, CF, and a hybrid of GF/CF is critical to investigating the local mechanical properties of intricate structures for high-end applications. In Phase I of this project, FOD in injection-molded panels with respect to distance from the gate was analyzed using X-ray computed tomography (X-CT) for GF, CF, and hybrid CF/GF (CGF) reinforced nylon 66. To understand the reason behind the FOD with different fiber types, computational fluid dynamics (CFD) and rheology were performed. Samples were extracted at three locations: near the gate, center, and opposite end. Thickness of the layers of typical skin-shell-core type FOD varies with fiber type and location. GF achieved flow direction alignment (in shell) earlier than viscous CF and CGF near the gate, whereas CF showed the highest flow-direction alignment at the center due to shear induced orientation. At the opposite end, GF experienced more backflow than others indicating faster mold filling owing to its lower viscosity. Hybrid CGF exhibited GF-dominated center and CF-dominated end region. The numerical model used to obtain FOD and rheological predictions for the CF and GF composites served to corroborate the trends observed in the experimental trials. The FOD responses across fiber types and location were reflected in their longitudinal and transverse properties. Only GF showed higher longitudinal modulus over transverse modulus near the gate attributed to rapid alignment, whereas CF and CGF exhibited opposite trend. However, fountain flow enhanced the longitudinal modulus over transverse modulus with the distance for all, particularly for CF. This study offers insights into mold filling behavior of different fibers which are critical in optimizing injection molding conditions for tailored final properties.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Graphene reinforced UHMWPE fibers

Thermoplastic polymers are increasingly used in electric vehicles, hydrogen fuel cell vehicles, and other decarbonization applications due to their lightweight and formability. Higher-strength polymers are needed to supplant metals in the vehicle structure, thereby reducing mass and improving efficiency. Ultra-high molecular weight polyethylene (UHMWPE) fibers possess one of the highest strength-to-weight ratios of technical polymers, and further improvement via reinforcement by nanofillers, such as graphene, will expand their performance envelope. Here, in this work, UHMWPE/graphene nanocomposite fibers were gel spun and characterized for their morphological, microstructural, thermal, and mechanical properties. The addition of a low fraction of graphene improved the tensile strength of the fibers by 25% and tensile modulus by 32%. Differential scanning calorimetry showed an increase in melting temperature and degree of crystallinity, which indicates improved coordination of the molecular chains induced by the addition of graphene. The reinforcement also affected the cross-sectional shape of the fibers; the aspect ratio of the fibers’ elliptical shape declined with increasing graphene content showing the skeletal effect of the graphene nanofillers in the polymer matrix. The reinforcing effect of graphene declined above a threshold concentration, and theoretical modeling was applied to demonstrate that increased agglomerates led to reduced properties. This work demonstrates a simple, effective method to produce graphene-reinforced UHMWPE fibers and lays a foundation for understanding the potential for leveraging graphene to form ultra-high-performance nanocomposite fibers for myriad engineering applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Solventless Dual‐Cure Liquid Resins Via Circular Use of Phthalic Anhydride for Recyclable Composite Applications

Abstract Fiber‐reinforced composites (FRCs) possess a remarkable strength‐to‐weight ratio, making them ideal light‐weighing alternative materials of metals used in automotive, aerospace, and outdoor equipment applications, but their recycling is challenging. Chemically recyclable thermoset polymers can enable fiber recovery and reuse; however, challenges remain in the separation and purification of depolymerized small molecules for efficient polymer recycling. To this end, a series of liquid resins for chemically recyclable polymer networks is designed based on phthalic anhydride, a widely produced and inexpensive chemical. The straightforward sublimation of phthalic anhydride is leveraged to enable a simple and efficient separation process for polymer recycling. To liquefy phthalic anhydride, five mono‐acryloyl‐phthalates are synthesized to obtain stable liquid resins together with phthalic diglycidyl ester. These liquid resins undergo dual‐cure reactions that comprise photopolymerization of acrylate and, subsequently, heat‐mediated epoxy‐acid polymerization reactions. These liquid resins exhibit moderate viscosities (2600–6400 cP @ 22 °C), fast curing, and robust thermomechanical properties (T g s from 71 to 116 °C). It is demonstrated that hydrolysis of the dual‐cured polymers completes within 2 h at 80 °C, and direct sublimation produces phthalic anhydride with 82% yield. This resin system is expected to provide a cost‐competitive, highly efficient platform for recyclable FRCs.

Polymer Science↗
DOE OSTI2025

Long carbon fibers boost performance of dry processed Li-ion battery electrodes

Dry processing (DP) is an advanced manufacturing technique for lithium-ion battery (LIB) electrodes. Unlike conventional wet-process-based manufacturing that involves dissolving polyvinylidene fluoride (PVDF) binder in n-methyl-2-pyrrolidone (NMP) solvent for slurry-casting, DP involves fibrillation of polymer binders. This method offers environmental and cost benefits by eliminating the need for expensive and environmentally hazardous organic solvents. However, DP-produced electrode films often lack mechanical stability due to the absence of a current collector substrate during electrode material layer fabrication. This reduced mechanical instability results in difficulty during fabricating of thin electrodes (≈5 mAh/cm 2 ). To address this issue, long (>8 mm) carbon fiber (CF) has been incorporated to reinforce the mechanical strength of the electrode films. In conclusion, the study demonstrates that the inclusion of long carbon fiber boosts the mechanical, electrical, thermal, and electrochemical performance of DP electrodes.

25 ENERGY STORAGE↗
DOE OSTI2026

Effect of fiber sizing and glass fiber laminate hybridization on vibration damping and mechanical properties of banana fiber reinforced polypropylene composites

Modern automotive applications demand lightweight, multifunctional materials to reach mileage goals and natural fiber reinforced composites (NFRCs) are one of the classes of materials proposed as a solution. NFRCs exhibit good vibration damping properties and have low density, but are often limited by processing challenges, poor-fiber matrix compatibility and variable performance. Herein, we investigate non-woven wet-lay of comingled banana fiber (BF), recycled glass fiber (rGF), and polypropylene (PP) fibers to in situ sizing and preparation of composite feedstocks for compression molding. BF and rGF hybrids were prepared by stacking rGF layers during compression molding to produce composites with various fiber ratios. The effect of fiber content, in-situ sizing and ratio of BF to rGF on tensile, flexural and vibration damping performance are investigated. Key results are the significant increase in tensile strength by in situ sizing (40 % sized at 60 wt% BF) and in flexural modulus (+58 % sized at 60 wt% BF) and flexural strength (+41 % sized 60 wt% BF) compared to the unsized equivalent. For BF-rGF hybrid composites with40 wt% total fiber content, flexural strength and modulus were improved by 51 % and 231 % respectively for a 1:1 ratio BF:rGF compared to BF reinforced system. Lastly, identifying the cross-over point where damping and stiffness are optimized for a hybrid composite. These findings demonstrate that these composites can be used as alternative to synthetic fiber or mineral filled composites in automotive applications, particularly where weight reduction, vibration damping and stiffness are desired.

Banana fiber↗
DOE OSTI2024

TuFF internal WRAP for Rapid Pipeline Repair (TuFF iWRAP)

The goal of “TuFF internal WRAP for Rapid Pipeline Repair” (TuFF iWRAP) program was to develop a novel material system and placement process to fabricate structural pipe within the existing deteriorated pipelines without disruption of gas delivery. The team (University of Delaware – Center for Composite Materials (UD-CCM) and Plitzie Inc.) addressed this challenge by developing a new material feedstock and pipe in pipe (PIP) repair strategy. This allows the potential for significant cost reduction and has minimum operational impact on gas customers. The new robotic based placement design allows discontinuous placement of pipe sections creating a stand-alone structural liner within the legacy pipeline without the need for pipe shutdown. Here, the material is supplied using a tethered material feeding system and is placed and UV cured with the internal Wound Rapid Automated Placement (iWRAP) system. This provides maximum placement efficiency capable of traversing 90 angle bends in 12-inch pipe and overall design customization to meet pipe repair requirements (e.g., variable wall thickness, bridging gaps, etc.). UV-curable fiber reinforced composite material has been optimized to meet structural performance and placement/cure times. Superior strength and fatigue life has been demonstrated by improving fiber-matrix adhesion using new fiber sizing for UV resins. Rapid cure approaches using new liner and resins have been evaluated with industry. The appropriate design of the section joints has been developed and tested. We estimate coating time to be ~100 hours per mile enabling typical pipe repair within 1 week.

03 NATURAL GAS↗