Results for “Equivalence Method” — Page 2

NASA NTRS1991

YBCO superconducting ring resonators at millimeter-wave frequencies

Microstrip ring resonators operating at 35 GHz were fabricated from laser ablated YBCO films deposited on lanthanum aluminate substrates. They were measured over a range of temperatures and their performances compared to identical resonators made of evaporated gold. Below 60 Kelvin the superconducting strip performed better than the gold, reaching an unloaded Q approximately 1.5 times that of gold at 25 K. A shift in the resonant frequency follows the form predicted by the London equations. The Phenomenological Loss Equivalence Method is applied to the ring resonator and the theoretically calculated Q values are compared to the experimental results.

Chorey, Christopher M.↗

NASA NTRS1992

Modeling of planar quasi-TEM superconducting transmission lines

An application of the phenomenological loss equivalence method (Lee and Itoh, 1989) in modeling the microwave behavior of planar quasi-TEM superconducting transmission lines is presented. For validation of the model, data are used from measurements of a YBCO superconducting thin-film coplanar-waveguide lowpass filter on a lanthanum aluminate substrate. Measured and modeled S-parameters of an existing superconducting coplanar waveguide lowpass filter agree to within 0.3 dB in magnitude and 0.5 radians in phase. Extracted values for penetration depth and real part of the conductivity of the superconducting film are within 10 percent of other researchers' findings.

Antsos, Dimitrios↗

NASA NTRS1991

A three-dimensional equivalent domain integral method for cracked solids

Three-dimensional FEM analysis is presently undertaken via the general formulation of the equivalent-domain integral method for mixed-mode fracture problems in general anisotropic and nonlinear materials. In mixed-mode integrals, the total J-integral is split into three separate modes of fracture; direct and decomposition methods are effective in this separation of the modes, as presently demonstrated by their application to several pure and mixed-mode fracture problems. The results are found to agree well with those reported in the literature, and suggest the usefulness of the method as a FEM-program postprocessing subroutines.

Shivakumar, K. N.↗

NASA NTRS1991

An equivalent domain integral method for three-dimensional mixed-mode fracture problems

A general formulation of the equivalent domain integral (EDI) method for mixed mode fracture problems in cracked solids is presented. The method is discussed in the context of a 3-D finite element analysis. The J integral consists of two parts: the volume integral of the crack front potential over a torus enclosing the crack front and the crack surface integral due to the crack front potential plus the crack face loading. In mixed mode crack problems the total J integral is split into J sub I, J sub II, and J sub III representing the severity of the crack front in three modes of deformations. The direct and decomposition methods are used to separate the modes. These two methods were applied to several mixed mode fracture problems, were analyzed, and results were found to agree well with those available in the literature. The method lends itself to be used as a post-processing subroutine in a general purpose finite element program.

Shivakumar, K. N.↗

NASA NTRS1992

An equivalent domain integral method for three-dimensional mixed-mode fracture problems

A general formulation of the equivalent domain integral (EDI) method for mixed mode fracture problems in cracked solids is presented. The method is discussed in the context of a 3-D finite element analysis. The J integral consists of two parts: the volume integral of the crack front potential over a torus enclosing the crack front and the crack surface integral due to the crack front potential plus the crack face loading. In mixed mode crack problems the total J integral is split into J sub I, J sub II, and J sub III representing the severity of the crack front in three modes of deformations. The direct and decomposition methods are used to separate the modes. These two methods were applied to several mixed mode fracture problems, were analyzed, and results were found to agree well with those available in the literature. The method lends itself to be used as a post-processing subroutine in a general purpose finite element program.

Shivakumar, K. N.↗

NASA NTRS1985

A theorem of equivalence on the methods of least-squares estimation

A theorem on the methods of least-squares estimation is stated and proved. This theorem enables the replacement of a system of correlated measurements by an equivalent system of uncorrelated measurements without a whitening process, thus simplifying the analysis while resulting in the same minimum-variance estimate.

Wu, S.-C.↗

NASA NTRS1985

Periodic solutions of second-order nonlinear difference equations containing a small parameter. II - Equivalent linearization

The classical method of equivalent linearization is extended to a particular class of nonlinear difference equations. It is shown that the method can be used to obtain an approximation of the periodic solutions of these equations. In particular, the parameters of the limit cycle and the limit points can be determined. Three examples illustrating the method are presented.

Mickens, R. E.↗

NASA NTRS1999

Static and Vibration Analyses of General Wing Structures Using Equivalent Plate Models

An efficient method, using equivalent plate model, is developed for studying the static and vibration analyses of general built-up wing structures composed of skins, spars, and ribs. The model includes the transverse shear effects by treating the built-up wing as a plate following the Reissner-Mindlin theory, the so-called First-order Shear Deformation Theory (FSDT). The Ritz method is used with the Legendre polynomials being employed as the trial functions. This is in contrast to previous equivalent plate model methods which have used simple polynomials, known to be prone to numerical ill-conditioning, as the trial functions. The present developments are evaluated by comparing the results with those obtained using MSC/NASTRAN, for a set of examples. These examples are: (i) free-vibration analysis of a clamped trapezoidal plate with (a) uniform thickness, and (b) non-uniform thickness varying as an airfoil, (ii) free-vibration and static analyses (including skin stress distribution) of a general built-up wing, and (iii) free-vibration and static analyses of a swept-back box wing. The results obtained by the present equivalent plate model are in good agreement with those obtained by the finite element method.

Kapania, Rakesh K.↗

DOE OSTI2021

Cross Section Generation Capability in Griffin

The Griffin code is a Multiphysics Object-Oriented Simulation Environment (MOOSE) based reactor multiphysics analysis application jointly developed by Idaho National Laboratory and Argonne National Laboratory. The code includes a variety of steady-state solvers for fixed-source, k-eigenvalue, adjoint, and subcritical multiplication, as well as transient solvers for point-kinetics, improved quasi-static, and spatial dynamics. The code reads multigroup cross sections in the ISOXML format generated from external deterministic or Monte Carlo cross section generation codes. The implementation of the cross section generation capability in Griffin was initiated last year by plugging in the cross section application programming interface (CSAPI) and reviewing the methodologies for treating particulate fuels. The focus this year was on improving the CSAPI integration and implementing advanced self-shielding methods for applications to advanced reactor problems with TRISO fuels. First, the process for cross section library generation was updated to accurately and rigorously produce isotopic cross section data. Second, the on-the-fly slowing down method for the resonance treatment was implemented in CSAPI to improve the accuracy of effective multigroup cross sections in the resonance energy range. Among various on-the-fly slowing down methods, the equivalent Dancoff factor cell method was employed. Third, the iterative local spatial self-shielding method was implemented under the calculation framework of the equivalent Dancoff factor cell method to accurately deal with the double heterogeneity effect of particulate fuel. The updated CSAPI with the advanced self-shielding methods, together with the cross section libraries generated based on the improved process, were tested for the very high temperature reactor (VHTR), high temperature test reactor (HTTR), and Empire benchmark problems with various resonance self-shielding conditions, indicating that the updated CSAPI in Griffin is able to produce multigroup cross sections accurately and efficiently. We also show that the methodology works well for pebble bed fuel from HTR-10, but the capability still needs to be fully integrated into CSAPI. In the future, further benchmark tests will be performed for various thermal reactor core problems, including particulate fuel-based pebble bed reactors.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS2004

Investigation of Acoustical Shielding by a Wedge-Shaped Airframe

Experiments on a scale model of an advanced unconventional subsonic transport concept, the Blended Wing Body (BWB), have demonstrated significant shielding of inlet-radiated noise. A computational model of the shielding mechanism has been developed using a combination of boundary integral equation method (BIEM) and equivalent source method (ESM). The computation models the incident sound from a point source in a nacelle and determines the scattered sound field. In this way the sound fields with and without the airfoil can be estimated for comparison to experiment. An experimental test bed using a simplified wedge-shape airfoil and a broadband point noise source in a simulated nacelle has been developed for the purposes of verifying the analytical model and also to study the effect of engine nacelle placement on shielding. The experimental study is conducted in the Anechoic Noise Research Facility at NASA Langley Research Center. The analytic and experimental results are compared at 6300 and 8000 Hz. These frequencies correspond to approximately 150 Hz on the full scale aircraft. Comparison between the experimental and analytic results is quite good, not only for the noise scattering by the airframe, but also for the total sound pressure in the far field. Many of the details of the sound field that the analytic model predicts are seen or indicated in the experiment, within the spatial resolution limitations of the experiment. Changing nacelle location produces comparable changes in noise shielding contours evaluated analytically and experimentally. Future work in the project will be enhancement of the analytic model to extend the analysis to higher frequencies corresponding to the blade passage frequency of the high bypass ratio ducted fan engines that are expected to power the BWB.

Gerhold, Carl H.↗

NASA NTRS2006

Investigation of Acoustical Shielding by a Wedge-Shaped Airframe

Experiments on a scale model of an advanced unconventional subsonic transport concept, the Blended Wing Body (BWB), have demonstrated significant shielding of inlet-radiated noise. A computational model of the shielding mechanism has been developed using a combination of boundary integral equation method (BIEM) and equivalent source method (ESM). The computation models the incident sound from a point source in a nacelle and determines the scattered sound field. In this way the sound fields with and without the airfoil can be estimated for comparison to experiment. An experimental test bed using a simplified wedge-shape airfoil and a broadband point noise source in a simulated nacelle has been developed for the purposes of verifying the analytical model and also to study the effect of engine nacelle placement on shielding. The experimental study is conducted in the Anechoic Noise Research Facility at NASA Langley Research Center. The analytic and experimental results are compared at 6300 and 8000 Hz. These frequencies correspond to approximately 150 Hz on the full scale aircraft. Comparison between the experimental and analytic results is quite good, not only for the noise scattering by the airframe, but also for the total sound pressure in the far field. Many of the details of the sound field that the analytic model predicts are seen or indicated in the experiment, within the spatial resolution limitations of the experiment. Changing nacelle location produces comparable changes in noise shielding contours evaluated analytically and experimentally. Future work in the project will be enhancement of the analytic model to extend the analysis to higher frequencies corresponding to the blade passage frequency of the high bypass ratio ducted fan engines that are expected to power the BWB.

Gerhold, Carl H.↗

NASA NTRS1994

On the wavelet optimized finite difference method

When one considers the effect in the physical space, Daubechies-based wavelet methods are equivalent to finite difference methods with grid refinement in regions of the domain where small scale structure exists. Adding a wavelet basis function at a given scale and location where one has a correspondingly large wavelet coefficient is, essentially, equivalent to adding a grid point, or two, at the same location and at a grid density which corresponds to the wavelet scale. This paper introduces a wavelet optimized finite difference method which is equivalent to a wavelet method in its multiresolution approach but which does not suffer from difficulties with nonlinear terms and boundary conditions, since all calculations are done in the physical space. With this method one can obtain an arbitrarily good approximation to a conservative difference method for solving nonlinear conservation laws.

Jameson, Leland↗

NASA NTRS1993

On the Daubechies-based wavelet differentiation matrix

The differentiation matrix for a Daubechies-based wavelet basis is constructed and superconvergence is proven. That is, it will be proven that under the assumption of periodic boundary conditions that the differentiation matrix is accurate of order 2M, even though the approximation subspace can represent exactly only polynomials up to degree M-1, where M is the number of vanishing moments of the associated wavelet. It is illustrated that Daubechies-based wavelet methods are equivalent to finite difference methods with grid refinement in regions of the domain where small-scale structure is present.

Jameson, Leland↗

NASA NTRS1995

Spectral methods on arbitrary grids

Stable and spectrally accurate numerical methods are constructed on arbitrary grids for partial differential equations. These new methods are equivalent to conventional spectral methods but do not rely on specific grid distributions. Specifically, we show how to implement Legendre Galerkin, Legendre collocation, and Laguerre Galerkin methodology on arbitrary grids.

Carpenter, Mark H.↗

NASA NTRS2006

Reconstruction of the Acoustic Field Using a Conformal Array

Near-field acoustical holography (NAH) requires the measurement of the near-field pressure field over a conformal and closed surface in order to recover the acoustic field on a nearby surface. We are interested in the reconstruction of the acoustic field over the fuselage of a Boeing 757 airplane when pressure data is available over an array of microphones that are conformal to the fuselage surface. In this case the strict NAH theory does not hold, but still there are techniques used to overcome this difficulty. The best known is patch NAH, which has been used for planar surfaces. In this work we will discuss two new techniques used for surfaces with an arbitrarily shape: patch inverse boundary element methods (IBEM) and patch equivalent sources method (ESM). We will discuss the theoretical justification of the method and show reconstructions for in-flight data taken inside a Boeing 757 airplane.

Valdivia, Nichlas P.↗

NASA NTRS1987

A finite element large deflection random response analysis of beams and plates subjected to acoustic loading

A finite element formulation is presented for the analysis of beams and rectangular plates undergoing large deflections subjected to Gaussian white noise excitations. Single-mode response is assumed in the present formulation. Root-mean-square (RMS) maximum deflections for simply supported and clamped beams and plates at various sound spectrum levels are obtained and compared with solutions using the Fokker-Planck-Kolmogorov equation and the equivalent linearization methods. RMS maximum stains and equivalent linear frequencies are compared with the equivalent linearization results for assessment of the accuracy of the finite element method.

Mei, Chuh↗

NASA NTRS1987

A simple method to model truss-beams as equivalent continua

A new method is presented for obtaining stiffness constants for structures modeled as three-dimensional linear elastic beams. The three-dimensional lattice is comprised of multiple two-dimensional lattices. Matrix manipulation is used to determine the contribution of each two-dimensional substructure to the complete three dimensional lattice.

Barton, O., Jr.↗

DOE OSTI2020

Normal modes, rotational inertia, and thermal fluctuations of trapped ion crystals

The normal modes of a trapped ion crystal are derived using an approach based on the Hermitian properties of the system’s dynamical matrix. This method is equivalent to the standard Bogoliubov method, but for classical systems it is arguably simpler and more general in that canonical coordinates are not necessary. The theory is developed for stable, unstable, and neutrally-stable systems. The method is then applied to ion crystals in a Penning trap. Reduced eigenvalue problems for the case of large applied magnetic field are developed, for which the spectrum breaks into E x B drift modes, axial modes, and cyclotron modes. Thermal fluctuation levels in these modes are analyzed and shown to be consistent with the Bohr-van-Leeuwen theorem, provided that neutrally-stable modes associated with crystal rotations are included in the analysis. An expression for the rotational inertia of the crystal is derived, and a magnetic contribution to this inertia, which dominates in large magnetic fields, is described. An unusual limit is discovered for the special case of spherically-symmetric confinement, in which the rotational inertia does not exist and changes in angular momentum leave the rotation frequency unaffected.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗