Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Energy density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Developing a bright 17 keV x-ray source for probing high-energy-density states of matter at high spatial resolution

A set of experiments were performed on the National Ignition Facility (NIF) to develop and optimize a bright, 17 keV x-ray backlighter probe using laser-irradiated Nb foils. High-resolution one-dimensional imaging was achieved using a 15 μm wide slit in a Ta substrate to aperture the Nb He{sub α} x-rays onto an open-aperture, time integrated camera. To optimize the x-ray source for imaging applications, the effect of laser pulse shape and spatial profile on the target was investigated. Two laser pulse shapes were used—a “prepulse” shape that included a 3 ns, low-intensity laser foot preceding the high-energy 2 ns square main laser drive, and a pulse without the laser foot. The laser spatial profile was varied by the use of continuous phase plates (CPPs) on a pair of shots compared to beams at best focus, without CPPs. A comprehensive set of common diagnostics allowed for a direct comparison of imaging resolution, total x-ray conversion efficiency, and x-ray spectrum between shots. The use of CPPs was seen to reduce the high-energy tail of the x-ray spectrum, whereas the laser pulse shape had little effect on the high-energy tail. The measured imaging resolution was comparably high for all combinations of laser parameters, but a higher x-ray flux was achieved without phase plates. This increased flux was the result of smaller laser spot sizes, which allowed us to arrange the laser focal spots from multiple beams and produce an x-ray source which was more localized behind the slit aperture. Our experiments are a first demonstration of point-projection geometry imaging at NIF at the energies (>10 keV) necessary for imaging denser, higher-Z targets than have previously been investigated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

“Ni-Less” Cathodes for High Energy Density, Intermediate Temperature Na-NiCl 2 Batteries

Among various battery technologies being considered for stationary energy storage applications, sodium-metal halide (Na-MH) batteries have become one of the most attractive candidates because of the abundance of raw materials, long cycle life, high energy density, and superior safety. However, one of issues limiting its practical application is the relatively expensive nickel (Ni) used in the cathode. In the present work, we focus on of efforts to develop new Ni-based cathodes, and demonstrate that a much higher specific energy density of 405 Wh/kg (23% higher than state-of-the-art Na-MH batteries) can be achieved at an operating temperature of 190oC. Furthermore, 15% less Ni is used in the new cathode than that in conventional Na-NiCl2 batteries. Long-term cycling tests also show stable electrochemical performance for over 300 cycles with excellent capacity retention (~100%). The results in this work indicate that these advances can significantly reduce the raw material cost associated with Ni (a 31% reduction) and promote practical applications of Na-MH battery technologies in stationary energy storage systems.

Chang, Hee-Jung↗

Sparingly solvating electrolytes for high energy density Lithium–sulfur batteries

Moving to lighter and less expensive battery chemistries compared to lithium-ion requires the control of energy storage mechanisms based on chemical transformations rather than intercalation. Lithium sulfur (Li/S) has tremendous theoretical specific energy, but contemporary approaches to control this solution-mediated, precipitation-dissolution chemistry requires using large excesses of electrolyte to fully solubilize the polysulfide intermediate. Achieving reversible electrochemistry under lean electrolyte operation is the only path for Li/S to move beyond niche applications to potentially transformational performance. An emerging topic for Li/S research is the use of sparingly solvating electrolytes and the creation of design rules for discovering new electrolyte systems that fundamentally decouple electrolyte volume from reaction mechanism. Furthermore, this perspective presents an outlook for sparingly solvating electrolytes as the key path forward for longer-lived, high-energy density Li/S batteries including an overview of this promising new concept and some strategies for accomplishing it.

25 ENERGY STORAGE↗

Measurement of the transverse energy density in Measurement of the transverse energy density in Au + Au collisions at $\sqrt{𝑠_{𝑁⁢𝑁}}$ = 200 GeV with the sPHENIX detector

Here, this paper reports measurements of the transverse energy per unit pseudorapidity (𝑑⁢𝐸 𝑇 /𝑑⁢𝜂) produced in Au + Au collisions at $\sqrt{𝑠_{𝑁⁢𝑁}}$ = 200 GeV, performed with the sPHENIX detector at the Relativistic Heavy Ion Collider (RHIC). The results cover the pseudorapidity range |𝜂| < 1.1 and constitute the first such measurement performed using a hadronic calorimeter at RHIC. Measurements of 𝑑⁢𝐸 𝑇 /𝑑⁢𝜂 are presented for a range of centrality intervals and the average 𝑑⁢𝐸 𝑇 /𝑑⁢𝜂 as a function of the number of participating nucleons, 𝑁 part , is compared to a variety of Monte Carlo heavy-ion event generators. The results are in agreement with previous measurements at RHIC, and feature an improved granularity in 𝜂 and improved precision in low-𝑁 part events.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

The high-energy-density counterpropagating shear experiment and turbulent self-heating

The counterpropagating shear experiment has previously demonstrated the ability to create regions of shock-driven shear, balanced symmetrically in pressure, and experiencing minimal net drift. This allows for the creation of a high-Mach-number high-energy-density shear environment. New data from the counterpropagating shear campaign is presented, and both hydrocode modeling and theoretical analysis in the context of a Reynolds-averaged-Navier-Stokes model suggest turbulent dissipation of energy from the supersonic flow bounding the layer is a significant driver in its expansion. A theoretical minimum shear flow Mach number threshold is suggested for substantial thermal-turbulence coupling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Talbot-Lau based Moiré deflectometry with non-coherent sources as potential High Energy Density plasma diagnostic

X-ray phase-contrast radiography could better characterize highly localized density gradients expected in High Energy Density (HED) plasma experiments than conventional attenuation radiography. In particular, the Talbot-Lau (TL) grating interferometer, which works with extended and polychromatic x-ray sources, is a potentially attractive HED diagnostic due to its high sensitivity. For HED characterization the TL setup and imaging techniques must be changed from the recently studied medical system. The object magnification must be increased greatly in order to resolve μm scale gradients while the Talbot magnification must be increased in order to keep the gratings away from the plasma. Additionally, techniques for retrieving the density profile from a single plasma image must be developed. We thus study the performance of high magnification TL interferometers, in conjunction with Moiré fringe deflectometry for single image phase retrieval. The results show a very good interferometer contrast (≤30%) at high magnification. The Moiré technique enables measuring both sharp and mild density gradients with good accuracy and spatial resolution. Both the laboratory and simulation studies indicate that the TL based Moiré deflectometry is more sensitive than the propagation phase-contrast method when utilizing an extended x-ray source (∼80 μm). In HED experiments this would allow for less demanding X-ray backlighters than those used at present.

36 MATERIALS SCIENCE↗

Differential heating: A versatile method for thermal conductivity measurements in high-energy-density matter

We propose a method for thermal conductivity measurements of high energy density matter based on differential heating. A temperature gradient is created either by surface heating of one material or at an interface between two materials by different energy deposition. The subsequent heat conduction across the temperature gradient is observed by various time-resolved probing techniques. Conceptual designs of such measurements using laser heating, proton heating, and x-ray heating are presented. The sensitivity of the measurements to thermal conductivity is confirmed by simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Requirements for Enabling Extreme Fast Charging of High Energy Density Li-Ion Cells while Avoiding Lithium Plating

To improve electric vehicle market acceptance, the charge time of their batteries should be reduced to 10–15 minutes. However, achieving 4C to 6C charge rates with today’s batteries is only possible for cells with thin electrodes coming at the expense of low energy density and high battery manufacturing cost. An electrochemical model is validated versus high rate charge data for cells with several loadings. The model elucidates that the main limitations for high energy density cells are poor electrolyte transport resulting in salt depletion within the anode and Li plating at the graphite/separator interface. Next, the model is used to understand what future electrode and electrolyte properties can help enable 4C and 6C charging. Ideally, future electrolytes would be identified with 2X conductivity, 3–4X diffusivity, and transference number of 0.5–0.6. Alternatively charging at elevated temperatures enhances electrolyte transport by 1.5X conductivity and 2–3X diffusivity with a negligible effect on transference number. Another effective strategy to enable 4C and 6C charging is reducing electrode tortuosity. Conversely, increasing electrode porosity and negative/positive ratio are ineffective strategies to improve fast charge capability.

Batteries↗

Potassium-Based alpha-Manganese Dioxide Nanofiber BinderFree Self-Supporting Electrodes: A Design Strategy for High Energy Density Batteries

This work minimizes electrode passive components and moves toward bridging the gap between actual and theoretical battery gravimetric energy density. Binder-free self-supporting (BFSS) cathodes were prepared from redox-active, high aspect ratio, potassium α-MnO2 nanofibers (K-OMS-2), eliminating the binder and current collector. The electroactive and structural element, K-OMS-2, was prepared using a scalable, moderate temperature, aqueous synthesis. The BFFS electrode approach allows fabrication of thick, high energy density electrodes with low impedance, with up to 10 fold improvement in delivered specific energy relative to conventional cathodes. This could enable high capacity large form factor cell designs, as required for applications demanding high energy content. In principle, this approach suggests a widely applicable paradigm for the construction of other BFFS electrodes through the targeted synthesis of other transition metal oxides with high aspect, fibrous morphologies. Introduction

25 ENERGY STORAGE↗

Demonstration of x-ray fluorescence imaging of a high-energy-density plasma

Experiments at the Trident Laser Facility have successfully demonstrated the use of x-ray fluorescence imaging (XRFI) to diagnose shocked carbonized resorcinol formaldehyde (CRF) foams doped with Ti. One laser beam created a shock wave in the doped foam. A second laser beam produced a flux of vanadium He-α x-rays, which in turn induced Ti K-shell fluorescence within the foam. Spectrally resolved 1D imaging of the x-ray fluorescence provided shock location and compression measurements. Additionally, experiments using a collimator demonstrated that one can probe specific regions within a target. These results show that XRFI is a capable alternative to path-integrated measurements for diagnosing hydrodynamic experiments at high energy density.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Tensor part of the Skyrme energy density functional. II. Deformation properties of magic and semi-magic nuclei

We study systematically the impact of the time-even tensor terms of the Skyrme energy density functional, i.e., terms bilinear in the spin-current tensor density, on deformation properties of closed-shell nuclei corresponding to 20,28,40,50,82, and 126 neutron or proton shell closures. We compare results obtained with three different families of Skyrme parametrizations whose tensor terms have been adjusted on properties of spherical nuclei: (i) TIJ interactions proposed in the first article of this series [T. Lesinski et al., Phys. Rev. C 76, 014312 (2007)] that were constructed through a complete readjustment of the rest of the functional and (ii) parametrizations whose tensor terms have been added perturbatively to existing Skyrme interactions, with or without readjusting the spin-orbit coupling constant. We analyze in detail the mechanisms at play behind the impact of tensor terms on deformation properties and how studying the latter can help screen out unrealistic parametrizations. It is expected that findings of the present article are to a large extent independent of remaining deficiencies of the central and spin-orbit interactions and will be of great value for the construction of future, improved energy functionals.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Characterization of spatially resolved high resolution x-ray spectrometers for high energy density physics and light source experiments

A high resolution 1D imaging x-ray spectrometer concept comprising a spherically bent crystal and a 2D pixelated detector is being optimized for diagnostics of small sources such as high energy density physics (HEDP) and synchrotron radiation or x-ray free electron laser experiments. This instrument is used on tokamak experiments for Doppler measurements of ion temperature and plasma flow velocity profiles. Laboratory measurements demonstrate a resolving power, E/ΔE of order 10 000 and spatial resolution better than 10 μm. Initial tests of the high resolution instrument on HEDP plasmas are being performed.

43 PARTICLE ACCELERATORS↗

MnBi particles with high energy density made by spark erosion

We report on the properties of low-temperature phase (LTP)-MnBi particles produced by the rapid-quenching technique of spark-erosion. The as-prepared powder consists of amorphous, crystalline, and superparamagnetic particles, mostly as porous aggregates. The major fraction of the powder consists of 20–30 nm particles. A short anneal crystallizes the amorphous particles producing a high moment, >90% of theoretical M{sub S}, albeit with H{sub C} of a few kOe. If lightly milled, the agglomerates are broken up to yield H{sub C} of 1 T. These findings are supported by the x-ray diffraction pattern showing broadened peaks of the predominant LTP-MnBi phase. The combination of spark erosion, milling, and annealing has produced randomly oriented particles with (BH){sub MAX} ∼ 3.0 MGOe. The particles are expected to show record energy product when aligned along their crystallographic easy axes.

36 MATERIALS SCIENCE↗