Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Emission mitigation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Responsibility for emissions and mitigation capability should guide use of carbon removal offsets

M Gidden conducted this work prior to joining PNNL and no DOE OFFICE OF SCIENCE, OTHER DOE, OTHER FEDERAL, OR PNNL OVERHEAD FUNDING is being used. Stabilizing and then drawing down global temperature requires achieving net-negative CO2 emissions globally. Carbon removal is needed to offset “hard-to-abate” sectors that remain sources of emissions at net-zero and beyond. We argue the use of scarce carbon removal resources should be guided by the principles enshrined in the Paris Agreement.

Gidden, Matthew↗
DOE OSTI2022

Mitigation of emissions and energy consumption due to light-duty vehicle size increases

Analysts need to consider the shift of light-duty vehicle sales from cars to light trucks to accurately project fuel consumption, greenhouse gas emissions, and consumer spending. Here, we find that energy consumed by on-road light-duty vehicles in the United States can vary by 10% by changing assumptions regarding the sales mix. Scenarios aligned with third-party forecasts, assuming a greater sales proportion of light trucks and fewer cars, yield petroleum consumption 3–8% higher than forecasts from the U.S. Energy Information Administration (EIA), with greenhouse gas emissions 5–7% higher and a 4–9% increase in consumer spending on vehicles and fuel. This incremental energy consumption can be offset by additional technologies for these vehicles. If most sedans were phased out in favor of larger sport utility vehicles, we find a sales share of 30% battery electric vehicles or 39% hybrid electric vehicles would equal the emissions of the EIA Reference Case.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Future grid mix impacts on whole-building life cycle assessment

Building construction and operation are a significant contribution to global greenhouse gas emissions, so understanding and mitigating emissions is crucial for reliable and realistic emissions accounting. Whole-building Life Cycle Assessment (WBLCA) is an emissions accounting method that considers lifetime environmental impacts of a building during its construction, operation, and eventual end-of-life. When performing WBLCAs, emission calculations from the building's operation over the entire building lifespan are typically based on today's energy grid mixes. This method does not consider changes or advancements in the clean energy proportion within the grid mix and can over or under-inflate results, skewing the ratio of embodied vs. operational environmental impacts. While a variety of prediction tools estimate what future grid emissions might be, predictions can vary widely. To predict the clean energy ratio within future grid mixes and the potential impact these changes might have on WBLCA, annual data from several existing U.S. grid models was averaged and probabilistic modeling was used to extend the usable projections of shorter forecasts. Results show that clean energy sources will likely continue to increase over time, although the rate of growth varies by model. On average, by 2085, the clean energy penetration of the grid is projected to reach ~81% and renewable energy is projected to reach ~71%, although no widespread consensus is reached. To understand how the future grid mix impacts lifetime building emissions within a WBLCA context, the team analyzed two 2021 IECC-compliant all-electric residential buildings: one built from traditional materials and construction processes and the other built with carbon sequestering materials and modular assembly, with a portion of energy generated on site. The results indicate that a moderate estimate of future electricity grid mixes shows a reduction of yearly operational emissions for traditional residential buildings of 55% between 2025 and 2085, and a corresponding reduction of 48% of total emissions over a 60 year building lifespan. This study offers a nuanced approach to account for the variability of future grid mix models and provides an average trend-line based on a robust collection of scenarios.

Life Cycle Assessment (LCA)↗
DOE OSTI2025

Mitigating field emission in SSR2 cryomodules for PIP-II

The SSR2 cavities for PIP-II have consistently been affected by field emission since the first cold tests with the unity coupler. A comprehensive root cause analysis was conducted to investigate the origin of this issue and to identify the fabrication, processing, and handling factors that have the greatest impact on field emission onset. New techniques were developed and effectively implemented to achieve field emission-free SSR2 cavities. In addition, effort was dedicated both to relating the radiation level measured at the test stand with the expected levels in the LINAC tunnel and to understand the evolution of field emission through the assembly steps. The challenge of overcoming field emission also led to a reassessment of design choices, enhancing our understanding of their effects on cavity performance.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Creating Accurate Methane Emission Inventories through Data-Driven Airborne Survey Strategies: Methods and Results from the Haynesville, Anadarko, and Permian Basins

Significantly reducing methane emissions from the oil and gas sector can decrease the rate of climate change over the next two decades, buying critical time for a global energy transition. However, emissions inventories that can be used by oil and gas operators and environmental regulators to identify optimal methane emission mitigation strategies are either based on conservative emission factor methods, or are inconsistent between studies due to differences in sampling strategies or survey technologies. We developed a new approach for methane emissions survey design that yields representative basinwide methane emissions inventories by surveying a subset of total assets in a given oil and gas basin. We identify several sampling and analysis principles, including large sample sizes, balanced sampling across oil and gas production, careful survey area definition, and a unified protocol for analysis, to be vital to producing an unbiased estimate of basin-scale emissions that can be reconciled with future studies. We further present results from deploying this strategy in two oil and gas producing regions in the United States: the Haynesville Basin in Texas and Louisiana, and the Woodford Shale in the Anadarko Basin in Oklahoma. Aerial surveys were performed in 2023 using the Insight M LeakSurveyor™ technology. Preliminary results from methane emissions detected by Insight M indicate that aerially detected emissions above roughly 30 kg(CH4)/hr by themselves contribute a fractional loss rate of 1.13% of gross gas production across oil and gas operations in the Haynesville Basin, with aerially detected emissions equivalent to 2.67% of gross gas production in the Woodford Shale. We supplement these aerial estimates with modeled emissions that are below the LeakSurveyor’s survey sensitivity using a recently published inventory-based model of methane emissions, which we update for our survey areas. We then combine our aerial detections with modeled emissions to yield methane emission distributions and inventories that incorporate the full range of potential methane emissions from the smallest to the largest. These results can be used to identify the most effective methane mitigation strategies for our study areas, and can be reconciled with future methane emissions surveys that use different technologies.

Sherwin, Evan (ORCID:0000000321804297)↗
DOE OSTI2025

Techno-economic evaluation of emission control configurations for AMP/PZ-based post-combustion CO 2 capture

Minimizing the environmental impacts of amine-based post-combustion carbon capture technologies is essential for regulatory compliance and public acceptance. Experimental campaigns at RWE's CO 2 capture pilot plant in Niederaussem using CESAR1 demonstrated that combining existing emission abatement technologies can substantially reduce the concentration of amines and degradation products in the CO 2 -depleted flue gas to below the detection limit of an infrared spectrometer. The campaign confirmed that a proprietary dry bed technology (OEASE aerozone™) or a second water wash can reduce AMP and PZ emissions to below 1 mg/Nm 3 . However, an acid or chemically active wash downstream of the water wash is necessary to reduce NH 3 emissions to very low levels (<2 mg/Nm 3 ). Combining a dry bed with an acid wash significantly reduces both the required acid solution and the resulting acid waste. The techno-economic analysis indicates that implementing emission mitigation technologies provides substantial environmental benefits for the CESAR1 process, with only a marginal increase (<1 €/tCO 2 ) in both the carbon capture cost (CCC) and CO 2 avoidance cost (CAC). The additional capital cost associated with extra column packing is offset by operational cost savings from reduced solvent losses. For stringent emission permits targeting NH 3 , a configuration combining a dry bed upstream of the water wash followed by an acid wash achieves the best balance between emission control and cost efficiency. This configuration results in a Levelized Cost of Electricity (LCOE) of 143 €/MWh, a CCC of 45.4 €/tCO 2 , and a CAC of 88.4 €/tCO 2 .

AMP↗
DOE OSTI2024

Air quality impacts from the development of unconventional oil and gas well pads: Air toxics and other volatile organic compounds

Unconventional oil and natural gas development (UOGD) has expanded rapidly across the United States in recent decades and raised concerns about associated air quality impacts. While significant effort has been made to quantify methane emissions, relatively few observations have been made of Volatile Organic Compounds (VOCs), especially during drilling and completion of new wells. Extensive air monitoring during development of several large, multi-well pads in Broomfield, Colorado, in the Denver-Julesburg Basin, provides a novel opportunity to examine changes in local air toxics and other VOC concentrations during well drilling and completions and production. These operations offer an especially useful case to study as several management practices were implemented to reduce emissions (e.g., electrified, grid-powered drill rigs and closed loop fluid handling systems to reduce truck traffic and limit fluid handling on the pad). With simultaneous measurements of methane and 50 VOCs from October 2018 to December 2022 at as many as 19 sites near well pads, in adjacent neighborhoods, and at a more distant reference location, we identify impacts from each phase of well development and production. Use of weekly, time-integrated canisters, a Proton Transfer Reaction Mass Spectrometer (PTR-MS), continuous photoionization detectors (PID) to trigger canister collection upon detection of VOC-rich plumes, and an instrumented vehicle, provided a powerful suite of measurements to characterize both transient plumes and longer-term changes in air quality. Prior to the start of well development, VOC gradients were small across Broomfield. Once drilling commenced, concentrations of oil and gas (O&G) related VOCs, including alkanes and aromatics, increased around active well pads. Concentration increases were clearly apparent during certain operations, including drilling, coil tubing/millout operations, and production tubing installation. Emissions of C 8 –C 10 n-alkanes during drilling operations highlighted the importance of VOC emissions from synthetic drilling mud chosen to reduce odor impacts. More than 90 samples were collected of transient plumes. Using composition measurements, meteorological data, and information about well pad activities, these plumes were connected with specific UOGD operations including drilling, flowback, and production equipment maintenance. The chemical signatures of these plumes differed by operation type (e.g., C 8 –C 10 n-alkanes constituted a larger fraction of measured VOCs in drilling-related plumes). Concentrations of individual, oil and gas-related VOCs in these plumes were often several orders of magnitude higher than in background air, with maximum ethane and benzene concentrations of 79,600 and 819 ppbv, respectively. Because these plumes typically impact a monitoring site for just several minutes, they are easily missed by slower-responding instruments. Study measurements highlight future emission mitigation opportunities during UOGD operations, including better control of emissions from shakers that separate drill cuttings from drilling mud, production separator maintenance operations, and periodic emptying of sand cans during flowback operations.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

A global comparison of building decarbonization scenarios by 2050 towards 1.5–2 °C targets

Buildings play a key role in the transition to a low-carbon-energy system and in achieving Paris Agreement climate targets. Analyzing potential scenarios for building decarbonization in different socioeconomic contexts is a crucial step to develop national and transnational roadmaps to achieve global emission reduction targets. This study integrates building stock energy models for 32 countries across four continents to create carbon emission mitigation reference scenarios and decarbonization scenarios by 2050, covering 60% of today’s global building emissions. These decarbonization pathways are compared to those from global models. Results demonstrate that reference scenarios are in all countries insufficient to achieve substantial decarbonization and lead, in some regions, to significant increases, i.e., China and South America. Decarbonization scenarios lead to substantial carbon reductions within the range projected in the 2 °C scenario but are still insufficient to achieve the decarbonization goals under the 1.5 °C scenario.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Design, Build, and Initial Testing of a Portable Methane Measurement Platform

The quantification of methane concentrations in air is essential for the quantification of methane emissions, which in turn is necessary to determine absolute emissions and the efficacy of emission mitigation strategies. These are essential if countries are to meet climate goals. Large-scale deployment of methane analyzers across millions of emission sites is prohibitively expensive, and lower-cost instrumentation has been recently developed as an alternative. Currently, it is unclear how cheaper instrumentation will affect measurement resolution or accuracy. To test this, the Wireless Autonomous Transportable Methane Emission Reporting System (WATCH 4 ERS) has been developed, comprising four commercially available sensing technologies: metal oxide (MOx,), Non-dispersion Infrared (NDIR), integrated infrared (INIR), and tunable diode laser absorption spectrometer (TDLAS). WATCHERS is the accumulated knowledge of several long-term methane measurement projects at Colorado State University’s Methane Emission Technology Evaluation Center (METEC), and this study describes the integration of these sensors into a single unit and reports initial instrument response to calibration procedures and controlled release experiments. Specifically, this paper aims to describe the development of the WATCH 4 ERS unit, report initial sensor responses, and describe future research goals. Meanwhile, future work will use data gathered by multiple WATCH 4 ERS units to 1. better understand the cost–benefit balance of methane sensors, and 2. identify how decreasing instrumentation costs could increase deployment coverage and therefore inform large-scale methane monitoring strategies. Both calibration and response experiments indicate the INIR has little practical use for measuring methane concentrations less than 500 ppm. The MOx sensor is shown to have a logarithmic response to methane concentration change between background and 600 ppm but it is strongly suggested that passively sampling MOx sensors cannot respond fast enough to report concentrations that change in a sub-minute time frame. The NDIR sensor reported a linear change to methane concentration between background and 600 ppm, although there was a noticeable lag in reporting changing concentration, especially at higher values, and individual peaks could be observed throughout the experiment even when the plumes were released 5 s apart. The TDLAS sensor reported all changes in concentration but remains prohibitively expensive. Our findings suggest that each sensor technology could be optimized by either operational design or deployment location to quantify methane emissions. The WATCH4ERS units will be deployed in real-world environments to investigate the utility of each in the future.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Cradle-to-Grave Lifecycle Analysis of Greenhouse Gas Emissions of Light-Duty Passenger Vehicles in China: Towards a Carbon-Neutral Future

Vehicle electrification is considered a pathway for on-road transportation decarbonization in China. Different from the conventional gasoline vehicles whose emissions are mainly released from vehicle tailpipes, emissions of battery electric vehicles (BEVs) are from the upstream processes of electricity generation and vehicle manufacturing, thus a comprehensive lifecycle analysis and comparison of BEVs with gasoline vehicles is required to quantify the emission mitigation benefit of vehicle electrification and determine the path to a carbon-neutral future. In the study, we compare the cradle-to-grave (C2G) lifecycle greenhouse gas emissions of gasoline and electric vehicles in China and analyze the greenhouse gas emission reduction of vehicle electrification in different provinces. Results show that under the current technologies, the national average C2G GHG emissions for battery electric vehicles (BEVs) of 100 miles (i.e., 160 km) and 300 miles (i.e., 480 km) all-electric range (AER) are 231 and 279 g CO2eq/km, respectively, 22% and 5% lower than those for gasoline internal combustion engine vehicles (ICEVs). Improving vehicle fuel efficiency by hybridizing gasoline ICEVs can effectively reduce C2G emissions to 212 g CO2eq/km. At the provincial level, C2G GHG emissions of BEVs vary according to the provincial electricity mix. In eight provinces, C2G GHG emissions of BEVs with 300 miles AER (BEV300s) are higher than those of gasoline ICEVs due to the GHG-intensive coal-based electricity mix. In the future scenario, with low carbon fuels (such as high-level bioethanol blending gasoline) and electricity decarbonization, the national average C2G emissions of hybrid electric vehicles (HEVs) and BEV300s can be reduced to 55 and 73 g CO2eq/km, respectively. Further decrease of C2G GHG emissions relies on reducing vehicle-cycle emissions from material processing and vehicle component manufacturing.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Dynamic Accounting of Carbon Uptake in the Built Environment

Transforming building materials from net life-cycle CO 2 e emitters to carbon sinks is a key pathway towards decarbonizing the industrial sector. Current life-cycle assessments of materials (particularly “low-carbon” materials) often focus on cradle-to-gate emissions, which can exclude emissions and uptake (i.e., fluxes) later in the materials’ life-cycle. Further, conventional CO 2 e emission characterization disregards the dynamic effects of the timing of emissions and uptake on cumulative radiative forcing from processes like manufacturing, biomass growth, and the decadal carbon storage in long-lived building materials. This work presents a framework to analyze the cradle-to-grave CO 2 e balance of building materials using a time-dependent global warming potential calculation. We apply this framework in the dynamic accounting of carbon uptake in the built environment (D-CUBE) tool and examine two case studies: concrete and cross-laminated timber (CLT). When accounting for dynamic effects, the long storage time of biogenic carbon in CLT results in reduced warming, while the slow rate of uptake via concrete carbonation does not result in significant reductions in global warming. The D-CUBE tool allows for consistent comparisons across materials and emissions mitigation strategies at varying life-cycle stages and can be adapted to other materials or systems with different lifespans and applications. The flexibility of D-CUBE and the ability to identify CO 2 e emission hot-spot life-cycle stages will be instrumental in identifying pathways to achieving net-carbon-sequestering building materials.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Investigating Building Energy Consumption and CO2 Emission in Phoenix Using AutoBEM and Future Typical Meteorological Year (fTMY) Weather Data

This research investigates the energy performance and CO2 emissions of each building stock across the Phoenix metropolitan area using the Automatic Building Energy Modeling (AutoBEM) framework and Model America v2 (MAv2) dataset from Oak Ridge National Laboratory (ORNL). Typical Meteorological Year (TMY) and Future Typical Meteorological Year (fTMY) files were used for AutoBEM simulation. The simulation results from TMY and fTMY were compared. It was found that a projected 10.28% increase in total CO2 emissions and a 9.30% rise in total energy consumption by 2080–2099 relative to current typical conditions. The results highlight the disparities in emissions among different building stocks and the influence of climate change on future energy demand. The findings underscore the necessity of targeted policy interventions and retrofitting strategies (eg. advanced HVAC systems, improved insulation, reflective roofing) to mitigate emissions in high-energy-use and emission-intensed buildings, particularly as climate conditions evolve. This study contributes to the growing understanding of building-sector emissions and their long-term implications under future climate scenarios.

Li, Hang [ORNL] (ORCID:0000000306001920)↗
DOE OSTI2021

How Much Could Article 6 Enhance Nationally Determined Contribution Ambition Toward Paris Agreement Goals Through Economic Efficiency?

The Paris Agreement of 2015 uses Nationally Determined Contributions (NDCs) to achieve its goal to limit climate change to well below 2°C. Article 6 allows countries to cooperatively implement NDCs provided they do not double-count mitigation. We estimate that economic efficiency gains from cooperative implementation of existing NDC goals using Article 6 could reduce the cost of achieving NDC goals in 2030 to all parties by ~$\$300$ × 10 9 , which if reinvested in additional emissions mitigation could add 9 billion tons CO 2 /year mitigation, beyond the 8 billion tons CO 2 /year currently pledged in 2030. We estimate that more than half of the 2030 gains could come from nature-based measures, but long-term potential for nature-based measures is more limited. How much or even if this economic potential can be realized is uncertain and will depend on both the rules and their implementation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Increased drought and extreme events over continental United States under high emissions scenario

The frequency, severity, and extent of climate extremes in future will have an impact on human well-being, ecosystems, and the effectiveness of emissions mitigation and carbon sequestration strategies. The specific objectives of this study were to downscale climate data for US weather stations and analyze future trends in meteorological drought and temperature extremes over continental United States (CONUS). We used data from 4161 weather stations across the CONUS to downscale future precipitation projections from three Earth System Models (ESMs) participating in the Coupled Model Intercomparison Project Phase Six (CMIP6), specifically for the high emission scenario SSP5 8.5. Comparing historic observations with climate model projections revealed a significant bias in total annual precipitation days and total precipitation amounts. The average number of annual precipitation days across CONUS was projected to be 205 ± 26, 184 ± 33, and 181 ± 25 days in the BCC, CanESM, and UKESM models, respectively, compared to 91 ± 24 days in the observed data. Analyzing the duration of drought periods in different ecoregions of CONUS showed an increase in the number of drought months in the future (2023–2052) compared to the historical period (1989–2018). The analysis of precipitation and temperature changes in various ecoregions of CONUS revealed an increased frequency of droughts in the future, along with longer durations of warm spells. Eastern temperate forests and the Great Plains, which encompass the majority of CONUS agricultural lands, are projected to experience higher drought counts in the future. Drought projections show an increasing trend in future drought occurrences due to rising temperatures and changes in precipitation patterns. Our high-resolution climate projections can inform policy makers about the hotspots and their anticipated future trajectories.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Performance and Durability of Proton Exchange Membrane Vapor-Fed Unitized Regenerative Fuel Cells

With a growing demand for electricity, clean hydrogen production and usage can be an asset not only to mitigate emissions but for long-term energy storage as well. Hydrogen gas, a high-density energy carrier, can be made through electrolysis in charging mode and generate electricity via a fuel cell in discharging mode in a unitized regenerative fuel cell (URFC). While URFCs reduce cost by combining the charging and discharging modes into a singular device, switching between modes becomes burdensome, and water management is a major challenge. One way to mitigate these issues is to operate the entire system in the vapor phase. Vapor-phase operation simplifies the physics of the system but will introduce losses within the system, primarily ohmic and mass transport during the charging mode. In this study, we explore the performance of a Proton-Exchange-Membrane (PEM)-URFC under vapor-phase conditions and the impact of different PEMs, feed gases, and relative humidity on the performance and durability. By tailoring operating conditions and membrane, the vapor-URFC achieves a roundtrip efficiency of 42% and a lifetime of 50,000 accelerated stress test cycles for fully humidified feeds. Discussion of vapor-URFC for energy storage and extensions to look at various applications shows the promise of this technology.

25 ENERGY STORAGE↗
DOE OSTI2026

Mechanistic Modeling of TEG Dehydrator Emissions in Oil and Gas Industry

This work presents a mechanistic modeling approach for simulating methane emissions from triethylene glycol (TEG) dehydrators used in oil & gas (O&G) operations. The model was developed as a modular component of the Mechanistic Air Emissions Simulator (MAES) tool, incorporating species-specific absorption and emission dynamics through two-level, second-order polynomial regression (PR) models trained on ProMax simulation data: (1) species-level regression models that track the transfer rates of individual gas species within the dehydrator unit streams, and (2) outlet flow stream regression models that predict the fraction of inlet gas distributed among the outlet streams of the dehydrator unit. These behaviors were characterized over a range of glycol circulation ratios, wet gas pressures, and temperatures. The model was validated using root mean square error (RMSE) analysis. The species-level PR achieved low root mean square error (RMSE) values (<0.03) for light hydrocarbon species across all dehydrator components, ranging from 0.0009 for methane to 0.029 for normal pentane. Similarly, the outlet-level PR yielded RMSE values below 0.002 for the dry gas fraction, 0.001 for the flash tank fraction, and 0.002 for the still vent fraction, demonstrating strong agreement between predicted and reference ProMax values. When deployed at field facilities, the model significantly improved MAES-simulated dehydrator emissions, revealing that gas-assisted glycol pump emissions are the dominant contributors to both dehydrator-level and site-level methane emissions under uncontrolled conditions. Further analysis of the 154 dehydrator units reported by operators under the AMI 2024 project showed that 54 units (31%) used gas-driven glycol pumps, of which 6 units (11%) operated with uncontrolled flash tanks, and 22 units (40.7%) were identified as potentially oversized. Of the six dehydrator units with uncontrolled gas-assisted pumps, pump emissions accounted for 90.25% of total dehydrator emissions and 63.10% of total site-level emissions. These findings highlight substantial opportunities for emissions mitigation through equipment upgrades.

MAES↗
DOE OSTI2025

Intercomparison of Three Continuous Monitoring Systems on Operating Oil and Gas Sites

We compare continuous monitoring systems (CMS) from three different vendors on six operating oil and gas sites in the Appalachian Basin using several months of data. We highlight similarities and differences between the three CMS solutions when deployed in the field and compare their output to concurrent top-down aerial measurements and to site-level bottom-up inventories. Furthermore, we compare vendor-provided emission rate estimates to estimates from an open-source quantification algorithm applied to the raw CMS concentration data. This experimental setup allows us to separate the effect of the sensor platform (i.e., sensor type and arrangement) from the quantification algorithm. We find that 1) localization and quantification estimates rarely agree between the three CMS solutions on short time scales (i.e., 30 min), but temporally aggregated emission rate distributions are similar between solutions, 2) differences in emission rate distributions are generally driven by the quantification algorithm, rather than the sensor platform, 3) agreement between CMS and aerial rate estimates varies by CMS solution but is close to parity when CMS estimates are averaged across solutions, and 4) similar sites with similar bottom-up inventories do not necessarily have similar emission characteristics. These results have important implications for developing measurement-informed inventories and for incorporating CMS-inferred emission characteristics into emission mitigation efforts.

54 ENVIRONMENTAL SCIENCES↗