SEARCH · Engineering Papers

Results for “Elemental Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Poromechanical cohesive interface element with combined Mode I-II cohesive zone elastoplasticity for simulating fracture in fluid-saturated porous media

A combined Mode I-II cohesive zone (CZ) elasto-plastic constitutive model, and a two-dimensional (2D) cohesive interface element (CIE) are formulated and implemented at small strain within an ABAQUS User Element (UEL) for simulating 2D crack nucleation and propagation in fluid-saturated porous media. Here, the CZ model mitigates problems of convergence for the global Newton-Raphson solver within ABAQUS, which when combined with a viscous stabilization procedure allows for simulation of post-peak response under load control for coupled poromechanical finite element analysis, such as concrete gravity dam stability analysis. Verification examples are presented, along with a more complex ambient limestone-concrete wedge fracture experiment, water-pressurized concrete wedge experiment, and concrete gravity dam stability analyses. A calibration procedure for estimating the CZ parameters is demonstrated with the limestone-concrete wedge fracture process. For the water-pressurized concrete wedge fracture experiment it is shown that the inherent time-dependence of the poromechanical CIE analysis provides a good match with experimental force versus displacement results at various crack mouth opening rates, yet misses the pore water pressure evolution ahead of the crack tip propagation. This is likely a result of the concrete being partially-saturated in the experiment, whereas the finite element analysis assumes fully water saturated concrete. For the concrete gravity dam analysis, it is shown that base crack opening and associated water uplift pressure leads to a reduced Factor of Safety, which is confirmed by separate analytical calculations.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Charges on a suspended silicon nitride membrane under a high-energy electron beam

Thin silicon nitride (SiN x ) membranes are widely used in gas and liquid phase transmission electron microscopy (TEM) and as phase plates to enhance imaging contrast. SiN x contains trap sites for both positive and negative charges, which can be manipulated by high-energy electron irradiation, external potential biasing, or light exposure. Charge accumulation on the membrane can significantly affect in situ TEM processes, including chemical and electrochemical reactions, nanoparticle dynamics, and catalytic activity, or introduce unwanted phase shifts when used as a phase plate. Here, in this study, charge accumulation on suspended SiN x membranes was investigated using off-axis electron holography combined with model-free charge analysis, supported by custom finite element analysis (FEA) simulations. An average residual positive charge density of approximately 2.8 × 10 −4 C m −2 was measured. Localized and stable regions of both positive and negative charges were identified on the membrane. The global positive and localized positive/negative charges give rise to strong electric fields and electroosmotic slip velocities at the membrane surface, which are sufficient to induce non-Brownian particle behavior and directional fluid flow, offering a physical explanation for previously observed anomalies in particle dynamics, nucleation, and growth during gas and liquid phase TEM experiments. These results provide a benchmark for understanding charge behavior at SiNx interfaces in gas and liquid phase TEM. Furthermore, the FEA simulations establish a framework for future investigations into charge distribution, electrostatic potentials, and electrical double layers at solid–liquid interfaces, particularly in complex geometries and chemically dynamic environments.

Suspended silicon↗

DOE OSTI2025

Measurement of partial vapor pressures of salt mixtures via combined horizontal transpiration and thermogravimetric analysis

A method combining thermogravimetric analysis (TGA) and horizontal transpiration with elemental analysis via inductively coupled plasma mass spectrometry or ion chromatography enabled calculation of partial pressures of individual salts in molten mixtures. TGA quantified total mass loss, while transpiration identified vapor-phase composition. Furthermore, two chloride (NaCl-MgCl 2 , NaCl-MgCl 2 + UCl 3 ) salts and one mixed halide (LiCl-LiF + Li 2 O) salt were analyzed at 750 °C and 550 °C, respectively. NaCl and MgCl 2 vapor pressures were 2.19–2.61 × 10 -4 atm and 2.47–2.48 × 10 -5 atm (dependent upon the identity of the invesitgated mixture); UCl 3 was 1.42 × 10 -7 atm. LiCl and LiF vapor pressures at 550 °C were 1.53 × 10 -6 and 6.32 × 10 -6 atm, respectively. Additionally, the TGA method was validated against values from the literature for unary LiCl and LiF.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Geometry and size dependent microstructure and crack formation in Rene 41 superalloy fabricated by laser powder bed fusion

This study provides a systematic investigation into the size and geometry-dependent microstructural evolution and cracking susceptibility of LPBF-fabricated Rene 41. By coupling experimental microstructural analysis with thermal modeling, this research uniquely identifies the relationship between geometry-specific thermal histories, carbide coarsening, and liquation cracking. Four different geometries with varying thickness were fabricated with the identical process parameters. It was found that the grain size and morphology are not affected by the part size. However, the thinner parts exhibited coarser sub-grain structures compared to the thicker ones. The crack formation was observed for the parts with cross-sections smaller than 1 mm, whereas thicker parts had high density without any defects. Further, the cracks were observed in the interdendritic regions, suggesting that liquation cracking was the active micro-crack formation mechanism. The detailed microstructural analysis combined with a thermal finite element analysis proved that the heat extraction efficiency was lower for thinner parts causing a lower cooling rate and coarser carbides, making them more susceptible to constitutional liquation. Microhardness measurements were conducted for each geometry and correlated with the observed microstructural variations. The findings highlight the critical need for geometry-specific optimization of LPBF process parameters to mitigate cracking and achieve microstructural uniformity, offering valuable insights into the fabrication of complex, high-performance aerospace components.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Sierra/SD – Its2Sierra – User's Manual – 5.22

The Integrated Tiger Series (ITS) generates a database containing energy deposition data. This data, when stored on an Exodus file, is not typically suitable for analysis within Sierra Mechanics for finite element analysis. The its2sierra tool maps data from the ITS database to the Sierra database. This document provides information on the usage of its2sierra.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Sierra/SD – Its2Sierra – User’s Manual (V.5.24)

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

Sierra/SD – Its2Sierra – User’s Manual – (V.5.26)

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

DOE OSTI2026

Sierra/SD – Its2Sierra – User’s Manual – 5.28

Incrementally updated theory documents associated with new software release. The Integrated Tiger Series (ITS) generates a database containing energy deposition data. This data, when stored on an Exodus file, is not typically suitable for analysis within Sierra Mechanics for finite element analysis. The its2sierra tool maps data from the ITS database to the Sierra database. This document provides information on the usage of its2sierra.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2026

Sierra/SD – Its2Sierra – User’s Manual 5.30

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

DOE OSTI2025

Nuclear forensic analysis on uranium ore concentrates: A multi-laboratory intercomparison study

A collaboration between the United States and Japan performed nuclear forensic analyses on a set of 7 uranium ore concentrate (UOC) samples with known origins to improve methodologies and best practices in the field. Overall, good agreement between the 4 participating laboratories was achieved for uranium assay, uranium isotope composition, strontium isotope composition, and trace element analysis. In conclusion, the combination of these four signatures is sufficient to distinguish the different origins among these studied UOCs.

and nuclear chemistry↗

DOE OSTI2026

MapsTorch : automatic differentiation for X-ray fluorescence data analysis

X-ray fluorescence (XRF) is a popular spectroscopy technique for elemental analysis. Spectrum fitting and parameter tuning are at the core of XRF analysis and are conventionally manually intensive, especially for synchrotron experiments involving large amounts of diverse samples. This work introduces the automatic differentiation (AD) technique to XRF and an open-source package called MapsTorch. By transforming an analytical model of the XRF spectrum into a differentiable computation graph with AD, MapsTorch enables robust optimization of parameters and elemental intensities. We evaluate MapsTorch by conducting computational experiments on a large number of historical synchrotron XRF datasets and compare its performance with the currently practiced fitting tool NLopt. The results show that MapsTorch consistently achieves high-quality fits and often leads to better fitting quality than NLopt, particularly in tasks such as initial spectrum fitting and elemental intensity refinement. The robust performance of MapsTorch paves the way for developing automated and high-throughput XRF data analysis workflows to handle the increasing data volumes expected from next-generation synchrotron facilities.

X-ray fluorescence↗

DOE OSTI2024

Machine tool cross beam design, fabrication, and testing using metal big area additive manufacturing

This paper describes the application of metal Big Area Additive Manufacturing (mBAAM) to the fabrication of a machine tool cross beam. The replacement of a traditional box design weldment with a new design printed by wire arc additive manufacturing using the MedUSA system at Oak Ridge National Laboratory (ORNL) is detailed. This requires a new design strategy based on the unique mBAAM capabilities. The intent of the new design is to reduce mass, while maintaining the dynamic stiffness. To compare the two designs, the natural frequencies and mode shapes are measured using impact testing and predicted using finite element analysis. It is confirmed that the printed structure dynamics agreed with the numerical model predictions, which demonstrates that it is feasible to model a large-scale mBAAM part and understand its behavior prior to printing. Another notable outcome of this study is that the significant residual stress and distortion in the print indicate that knowledge gaps remain for widespread implementation of mBAAM.

42 ENGINEERING↗

DOE OSTI2024

High plasticity in refractory composite fabrication by ultrasonic additive manufacturing

Refractory metal composites are desirable for use in extreme environments that require materials with high specific strengths and resilience to external environments such as that found in nuclear and aerospace. However, due to the high melting temperature of refractories, liquid state joining processes such as welding remains difficult. Ultrasonic additive manufacturing (UAM) provides a potential route for processing refractory composites because it is a solid-state (i.e., no-melting) process and allows for intermittent machining operations to be performed between welds. Further, to demonstrate refractory composite fabrication, this study utilized UAM to machine a cavity to locate and sequester a Mo foil in a Zircaloy-4 (Zry-4) baseplate and additively build over the top with Zry-4 foils, thereby embedding the Mo in Zry-4 matrix. Significant deformation of the Zry-4 microstructure was observed: this deformation caused adiabatic heating and subsequent dynamic recrystallization through the transformation from α→β and then back to α as the material cooled. Flexural testing of the Zr–Mo composite revealed no delamination or failure, but the strength was not as expected, falling lower than a cold-worked Zry-4 sample. Finite element analysis supported that some bonding must have existed between the Zry-4 and Mo. There was indeed an interdiffusion zone at the Zry-4 foil–Mo foil interface, observing a metastable body-centered cubic β-Zr lathe. It was determined that sufficient strain energy was present to encourage the nucleation of the β-Zr grain along α-Zr grains. Future work is warranted to investigate UAM for refractory composite fabrication.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Framework development for a SAVY-4000 nuclear material storage container structural integrity surveillance tool

Here, this work presents the preliminary design of an automated surveillance tool to assess the health of SAVY-4000 nuclear material storage containers. This tool is designed by training several machine learning (ML) regression models to predict maximum residual stress in plain dents on the container sidewall. The model is trained on an experimentally validated Finite Element Analysis (FEA) model built in Abaqus FEA. The accuracy of each ML model is compared. The potential for application as well as model shortcomings are assessed. Necessary FEA model improvements are outlined and the various ML models are proposed.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Machine Learning in the Context of Laser-Induced Breakdown Spectroscopy

The integration of machine learning (ML) with Laser-Induced Breakdown Spectroscopy (LIBS) has revolutionized the analytical capabilities of LIBS. The combi-nation of both methods enables more accurate and efficient data analysis. While LIBS itself is a powerful technique for elemental analysis, the vast amount of spectral data it generates can be hard to interpret. Machine learning addresses these challenges by leveraging algorithms that can learn from data, identify patterns, and make predictions without explicit programming for the interpretation of each specific task. In LIBS application, ML techniques are used to enhance various analytical processes. For example, ML algorithms can classify materials based on their spectral fingerprints, predict the concentration of elements in a sample, and identify underlying patterns within complex datasets. Here, this application improves the precision of LIBS analyses while significantly reducing the time required for data processing and interpretation. In this chapter, the fundamental concepts of ML will be discussed first. Following this, the process of data splitting and the importance of feature selection will be examined. Several machine learning methods will then be closely examined, exploring how each can benefit LIBS analysis and highlighting their respective advantages and shortcomings. This structured approach will provide a comprehensive understanding of the integration of ML in the context of LIBS analysis.

47 OTHER INSTRUMENTATION↗

DOE OSTI2025

Enriched immersed finite element and isogeometric analysis: algorithms and data structures

Immersed finite element methods provide a convenient analysis framework for problems involving geometrically complex domains, such as those found in topology optimization and microstructures for engineered materials. However, their implementation remains a major challenge due to, among other things, the need to apply nontrivial stabilization schemes and generate custom quadrature rules. This article introduces the robust and computationally efficient algorithms and data structures comprising an immersed finite element preprocessing framework. The input to the preprocessor consists of a background mesh and one or more geometries defined on its domain. The output is structured into groups of elements with custom quadrature rules formatted such that common finite element assembly routines may be used without or with only minimal modifications. The key to the preprocessing framework is the construction of material topology information, concurrently with the generation of a quadrature rule, which is then used to perform enrichment and generate stabilization rules. While the algorithmic framework applies to a wide range of immersed finite element methods using different types of meshes, integration, and stabilization schemes, the preprocessor is presented within the context of the extended isogeometric analysis. This method utilizes a structured B-spline mesh, a generalized Heaviside enrichment strategy considering the material layout within individual basis functions’ supports, and face-oriented ghost stabilization. Using a set of examples, the effectiveness of the enrichment and stabilization strategies is demonstrated alongside the preprocessor’s robustness in geometric edge cases. Additionally, the performance and parallel scalability of the implementation are evaluated.

Computer implementation↗

DOE OSTI2026

Advancing SiC clad fuel performance model: bridging micro- and macro-scale models and experimental validation

This report presents a workflow for advancing fuel performance modeling of SiC composite cladding for light-water reactors by linking microscale, experimental data-informed finite element analysis with rod-scale fuel performance codes such as BISON. The workflow uses X-ray computed tomography (XCT) to capture the actual geometry and processing-induced defects of as-fabricated SiC composite tube specimens, particularly porosity and wall-thickness variations, and converts the segmented XCT volumes into image-based finite element meshes for high fidelity structural analysis.

Koyanagi, Takaaki [Oak Ridge National Laboratory (↗

DOE OSTI2025

The molten salt tritium transport experiment: A pumped fluoride salt loop for hydrogen isotope experimentation

Molten salt reactors (MSRs) and fusion reactors propose to use molten salts as coolants and breeder blanket materials, respectively. Tritium, however, poses safety concerns in both reactor types due to its ability to permeate through reactor materials and potential for environmental release. This manuscript addresses the tritium transport phenomena in molten salts and presents the design and analysis of the Molten Salt Tritium Transport Experiment (MSTTE). MSTTE is a forced-convection fluoride salt loop intended to measure hydrogen isotope permeation through structural materials in a flowing salt system. In the first phase, MSTTE will use FLiNaK salt and deuterium as surrogates for FLiBe and tritium, with future plans to utilize tritium and FLiBe. MSTTE couples a Copenhagen Atomics pumped salt loop with an external test section that introduces hydrogen isotopes into the loop and measures transport phenomena. The Hydrogen Injection System (HIS) controls hydrogen isotope introduction into the molten salt loop. Here, the permeation test section measures the permeation rate through stainless steel tubing in contact with flowing salt. Computational fluid dynamics (CFD) analysis ensures fully developed salt flow in the permeation test section. MSTTE is modeled with MELCOR-TMAP to predict the permeation rate as a function of experimental variables such as source term, salt flow rate, and salt temperature. Results indicate that the source term is the only parameter with a significant effect on the permeation rate. Pressure drop analysis suggests that the loop should operate below 200 LPM to maintain a pressure drop below 200 kPa. Additionally, finite-element analysis assesses thermal stress during loop operation to ensure the experiment's safe design. MSTTE will provide semi-integral data on tritium transport phenomena in molten salts and serve as a testbed for advancing molten salt technology.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗