SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Hydraulic system provides smooth control of large tracking and antenna drive systems at very low tracking rates. This configuration modifies a series connection of the drive motors with compensating orifices to offset the effects of drain line loss. Linearization of response by eliminating cogging or cyclic operation is thus obtained.
A novel motor drive system has been described for use in electrostatic generator/motor systems based on the time variation of capacity of a rotating condenser comprised of segmented rotor and stator elements. It takes advantage of the fact that the motor action of such a system depends only on the rms value of the drive pulses, which therefore can be formed simply by periodically interrupting a high-frequency ac wave train. This new circuitry simplifies the drive system and takes advantage of recent developments of devices used in the art of inversion of dc voltages to high-frequency (tens of kiloHz) ac.
We present the design of the flashlamp drive system for the NG100 laser, a 1 J/pulse, 10–100 kHz, pulse-burst Nd:YAG laser system being developed for application in a Thomson scattering plasma diagnostic. This flashlamp drive system is under active development, with a prototype now being constructed. The flashlamp drive system is modular, with each module capable of driving a series pair of linear flashlamps. Each drive module contains and is controlled by a dedicated Analog Regulator Controller. Thus each module is independently operable and controllable. This modular approach imposes no intrinsic limit to the number of modules that may be applied to drive the flashlamp pairs in a laser system. Each flashlamp drive module has a switch-regulated topology. An 1800 V main capacitor bank provides 25 kJ of energy storage, while a lower voltage output capacitor bank provides filtering and the initial energy delivered to the flashlamps at the start of the drive pulse. The main bank is recharged after each flashlamp drive pulse. As energy is drawn from the output bank by the flashlamps, an IGBT switching regulator feeds current from the main bank through an inductor to replenish the output capacitor bank. The rate of replenishment is feedback-controlled to maintain a regulated supply of power to the flashlamp load, with a setpoint range of 0.07 to 1.65 MW. An Analog Regulator Controller produces two-state variable pulse width feedback switching of the regulator IGBT. The switching frequency is ≤ 20 kHz, dynamically adjusted to limit ripple of the flashlamp power to ±3% statistical standard deviation of mean. For development or troubleshooting, each module is operable independent of the laser digital control system (microcontroller and FPGA).
The establishment of propfan technology readiness was determined and candidate drive systems for propfan application were identified. Candidate testbed aircraft were investigated for testbed aircraft suitability and four aircraft selected as possible propfan testbed vehicles. An evaluation of the four candidates was performed and the Boeing KC-135A and the Gulfstream American Gulfstream II recommended as the most suitable aircraft for test application. Conceptual designs of the two recommended aircraft were performed and cost and schedule data for the entire testbed program were generated. The program total cost was estimated and a wind tunnel program cost and schedule is generated in support of the testbed program.
Electric drive system provides low speed, long term tracking of targets that move at a sidereal rate. It utilizes eddy-current energized actuators that are free from radio frequency interference generation and a solid state feedback amplifier with provisions for antibacklash biasing.
A physical model of the Altitude Wind Tunnel drive system is developed that will produce the desired performance. Viewgraphs show: key personnel; critical aspects and scale modeling of the drive system; and drawings of the wind tunnel and specific sections.
Motor drive system remotely operates heavy steel radiation shielding doors. The drive consists of a standard motor reducer unit which is mounted on the door. This reducer drives a sprocket which is linked by chain to a fixed sprocket of the same size on the door jamb.
Motion drive system has been developed for use with interferometers where accurate control of minuscule distance in the 1-micron range is of prime importance. The drive system is applicable to any device that requires extremely accurate positioning control.
This paper describes a two-axis drive system for pointing a high-gain antenna. Motion about each axis is provided by identical drive mechanisms. The drive is unique in that only three gear passes are required to obtain the necessary 900:1 gear reduction. The drive system is a primary element of an experiment that will provide a real-time data link between Nimbus and certain ground stations. In this experiment data are transmitted from Nimbus to the applications technology satellite, which relays the data to ground stations.
Antibacklash circuit for hydraulic drive system
Synchronous dc direct-drive system comprising multiple-loop hybrid control system controlling load directly connected to actuator
Boeing, Rolls Royce, and NASA have worked together to complete a parametric sizing study for NASA's Large Civil Tilt Rotor (LCTR2) concept 2nd iteration. Vehicle gross weight and fuel usage were evaluated as propulsion and drive system characteristics were varied to maximize the benefit of reduced rotor tip speed during cruise conditions. The study examined different combinations of engine and gearbox variability to achieve rotor cruise tip speed reductions down to 54% of the hover tip speed. Previous NASA studies identified that a 54% rotor speed reduction in cruise minimizes vehicle gross weight and fuel burn. The LCTR2 was the study baseline for initial sizing. This study included rotor tip speed ratios (cruise to hover) of 100%, 77% and 54% at different combinations of engine RPM and gearbox speed reductions, which were analyzed to achieve the lightest overall vehicle gross weight (GW) at the chosen rotor tip speed ratio. Different engine and gearbox technology levels are applied ranging from commercial off-the-shelf (COTS) engines and gearbox technology to entry-in-service (EIS) dates of 2025 and 2035 to assess the benefits of advanced technology on vehicle gross weight and fuel burn. Interim results were previously reported1. This technical paper extends that work and summarizes the final study results including additional engine and drive system study accomplishments. New vehicle sizing data is presented for engine performance at a single operating speed with a multispeed drive system. Modeling details for LCTR2 vehicle sizing and subject engine and drive sub-systems are presented as well. This study was conducted in support of NASA's Fundamental Aeronautics Program, Subsonic Rotary Wing Project.
A current-source inverter (CSI) has the natural capability of boosting the output voltage which is a notable advantage over voltage source inverter (VSI) in traction drive applications. This paper investigates the voltage boosting feature of the CSI to improve the overall efficiency of the CSI-based surface permanent magnet (SPM) machine drive system in the constant power region. The effects of the boost function on the total system losses, including the machine copper loss, core loss, and magnet loss, as well as the device conduction and switching loss in the CSI and dc/dc converter, are described using analytical models. The operating characteristics of the machine and CSI are validated by 2-D finite-element analysis (FEA) and simulations. Based on the loss model, the effects of the modulation index on the overall drive system losses and power factor have been analyzed. A genetic algorithm has been used to optimize the CSI's boost ratio, demonstrating that the drive system efficiency can be increased by 1% to 2.5% along the constant-power regime envelope by using the boost function.
High speed gearing performance is very important to the overall drive system efficiency. Certain losses such as gear meshing and bearing drag can be minimized by design changes such as pressure angle of the gears and the geometry and type of bearings being used. One component that can have a large effect on the overall performance of high-speed drive systems is the parasitic drag known as gear windage. This loss mechanism is not well understood and minimizing this component is usually accomplished through much trial and error. The results presented in this paper will document some of the design parameter effects on the amount of windage losses. A new test facility at NASA Glenn has been assembled to systematically study the design variables. Results from recent tests will be presented. The tests are for a single gear, with and without lubricants, and some initial studies using shrouds
High speed gearing performance is very important to the overall drive system efficiency. Certain losses such as gear meshing and bearing drag can be minimized by design changes such as pressure angle of the gears and the geometry and type of bearings being used. One component that can have a large effect on the overall performance of high-speed drive systems is the parasitic drag known as gear windage. This loss mechanism is not well understood and minimizing this component is usually accomplished through much trial and error. The results presented in this paper will document some of the design parameter effects on the amount of windage losses. A new test facility at NASA Glenn has been assembled to systematically study the design variables. Results from recent tests will be presented. The tests are for a single gear, with and without lubricants, and some initial studies using shrouds.
This paper describes the development of a transistorized PWM inverter-induction motor traction drive system. A vehicle performance analysis was performed to establish the vehicle tractive effort-speed requirements. These requirements were then converted into a set of inverter and motor specifications. The inverter was a transistorized three-phase bridge using General Electric power Darlington transistors. The description of the design and development of this inverter is the principal object of this paper. The high-speed induction motor is a design which is optimized for use with an inverter power source. The primary feedback control is a torque angle control with voltage and torque outer loop controls. A current-controlled PWM technique is used to control the motor voltage. The drive has a constant torque output with PWM operation to base motor speed and a constant horsepower output with square wave operation to maximum speed. The drive system was dynamometer tested and the results are presented.
This project involved developing a fully integrated high speed megawatt class motor and high frequency variable speed drive system that serve as a commercially viable and technically sound methodology for high speed industrial system applications. The project team organizations consist of Clemson University and TECO Westinghouse Motor Company (TWMC) formed an academic and industrial collaboration that combines the design, analysis, manufacturing and testing experience required for a large research project of this magnitude. The project resulted in an integrated high speed megawatt class medium voltage motor drive system that is at a TRL 6 with a clear path for commercialization. The fully integrated prototype system has been manufactured by TWMC in its Round Rock, Texas facility and tested at full power on a dynamometer at the Clemson University’s eGRID Center in North Charleston, South Carolina.
Eddy current clutch drives for tracking antenna system