Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffusion coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Nonlinearity Effects of Lateral Density Diffusion Coefficient on Gain-Guided VCSEL Performance

Electron and hole diffusions in the plane of semiconductor quantum wells play an important part in the static and dynamic operations of semiconductor lasers. In this paper, we apply a hydrodynamic model developed from the semiconductor Bloch equations to numerically study the effects of nonlinearity in the diffusion coefficient on single mode operation and direct modulation of a gain-guided InGaAs/GaAs multiple quantum well laser, operating not too far from threshold. We found that a small diffusion coefficient is advantageous for lowering the threshold current and increasing the modulation bandwidth. Most importantly, the effects of nonlinearity in the coefficient can be approximately reproduced by replacing the coefficient with an effective constant diffusion coefficient, which corresponds roughly to the half height density of the density distribution.

Li, Jian-Zhong↗
NASA NTRS1978

Determination of the zincate diffusion coefficient and its application to alkaline battery problems

The diffusion coefficient for the zincate ion at 24 C was found to be 9.9 x 10 to the -7th power sq cm/sec + or - 30% in 45% potassium hydroxide and 1.4 x 10 to the -7th power sq cm/sec + or - 25% in 40% sodium hydroxide. Comparison of these values with literature values at different potassium hydroxide concentrations show that the Stokes-Einstein equation is obeyed. The diffusion coefficient is characteristic of the zincate ion (not the cation) and independent of its concentration. Calculations with the measured value of the diffusion coefficient show that the zinc concentration in an alkaline zincate half-cell becomes uniform throughout in tens of hours by diffusion alone. Diffusion equations are derived which are applicable to finite-size chambers. Details and discussion of the experimental method are also given.

May, C. E.↗
NASA NTRS1978

Determination of the zincate diffusion coefficient and its application to alkaline battery problems

The diffusion coefficient for the zincate ion at 24 C was found to be 9.9 X 10 to the minus 7th power squared cm per sec + or - 30 percent in 45 percent potassium hydroxide and 1.4 x 10 to the minus 7 squared cm per sec + or - 25 percent in 40 percent sodium hydroxide. Comparison of these values with literature values at different potassium hydroxide concentrations show that the Stokes-Einstein equation is obeyed. The diffusion coefficient is characteristic of the zincate ion (not the cation) and independent of its concentration. Calculations with the measured value of the diffusion coefficient show that the zinc concentration in an alkaline zincate half cell becomes uniform throughout in tens of hours by diffusion alone. Diffusion equations are derived which are applicable to finite size chambers. Details and discussion of the experimental method are also given.

May, C. E.↗
DOE OSTI2021

Atomistic and mesoscale simulations to determine effective diffusion coefficient of fission products in SiC

The silicon carbide (SiC) layer in tristructural isotropic (TRISO) particles serves as the barrier to prevent escape of fission products produced in the fuel kernel. Knowing the diffusion coefficient of fission products through SiC is critical to determining whether fission gas can escape from the particle. It has been observed in experiments that Ag accumulated in grain boundaries and triple junctions in SiC. It is hypothesized that grain boundary diffusion is the primary pathway by which fission products penetrate the SiC layer. In this report, the effective diffusion coefficient of the fission product Ag through the grain boundary network is calculated using a combination of atomistic and phase-field methods. The grain boundary diffusion coefficient is calculated using molecular dynamics simulations. The bulk diffusion coefficient is determined using a combination of density functional theory and nudged elastic band methods. An effective diffusion coefficient is calculated, accounting for the grain structure using a phase-field method. The effective diffusion coefficient will be incorporated into Bison and fission product release calculations are compared to available experimental data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1972

Composition dependence of ion diffusion coefficients in gas mixtures at arbitrary field strengths

Expressions for the diffusion coefficient of ions in gas mixtures are obtained from momentum transfer theory, and are given in terms of the diffusion coefficients and drift velocities of the ions in the pure component gases. Blanc's law holds exactly at all field strengths if the mean free time between collisions is independent of velocity (Maxwell model), but otherwise there may be either positive or negative deviations from Blanc's law at high fields. Such deviations are of comparable magnitude for the diffusion coefficients and the mobility, but are not identical. Specific cases of inverse-power potentials are treated in further detail, and some numerical examples are given for rigid-sphere interactions.

Whealton, J. H.↗
NASA NTRS1983

Solutal diffusion coefficient for liquid PbTe-SnTe

The solutal diffusion coefficient has been determined for liquid lead telluride-tin telluride using a modified shear cell technique. Postdiffusion concentration profiles are presented for several diffusion couples. The best analytical curve fit to the data gives a composition-dependent diffusion coefficient of (/3/7/ to the C power) x 0.00014 sq cm/sec, where C is the PbTe concentration. In addition, data are presented to show the importance of solutal convection in the lead-tin-telluride system.

Clark, I. O.↗
DOE OSTI2021

Using Computationally-Determined Properties for Machine Learning Prediction of Self-Diffusion Coefficients in Pure Liquids

The ability to predict transport properties of liquids quickly and accurately will greatly improve our understanding of fluid properties both in bulk and complex mixtures, as well as in confined environments. Such information could then be used in the design of materials and processes for applications ranging from energy production and storage to manufacturing processes. As a first step, we consider the use of machine learning (ML) methods to predict the diffusion properties of pure liquids. Recent results have shown that Artificial Neural Networks (ANNs) can effectively predict the diffusion of pure compounds based on the use of experimental properties as the model inputs. In the current study, a similar ANN approach is applied to modeling diffusion of pure liquids using fluid properties obtained exclusively from molecular simulations. A diverse set of 102 pure liquids is considered, ranging from small polar molecules (e.g., water) to large nonpolar molecules (e.g., octane). Self-diffusion coefficients were obtained from classical molecular dynamics (MD) simulations. Since nearly all the molecules are organic compounds, a general set of force field parameters for organic molecules was used. The MD methods are validated by comparing physical and thermodynamic properties with experiment. Computational input features for the ANN include physical properties obtained from the MD simulations as well as molecular properties from quantum calculations of individual molecules. Furthermore, fluid properties describing the local liquid structure were obtained from center of mass radial distribution functions (COM-RDFs). Feature sensitivity analysis revealed that isothermal compressibility, heat of vaporization, and the thermal expansion coefficient were the most impactful properties used as input for the ANN model to predict the MD simulated self-diffusion coefficients. The MD-based ANN successfully predicts the MD self-diffusion coefficients with only a subset (2 to 3) of the available computationally determined input features required. A separate ANN model was developed using literature experimental self-diffusion coefficients as model targets. Although this second ML model was not as successful due to a limited number of data points, a good correlation is still observed between experimental and ML predicted self-diffusion coefficients.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Estimating the Diffusion Coefficient of Lithium in Graphite: Extremely Fast Charging and a Comparison of Data Analysis Techniques

Galvanostatic intermittent titration experiments were performed in three-electrode cells to characterize the effect of C/2, 2-C and 4-C charge rates on the observed lithium diffusion coefficient. As part of the data analysis process, we compared the classic Weppner-Huggins analysis of polarization data with a newer (Wang et al.) analysis method for depolarization data. At low values of x in Li x C 6 , both analysis methods showed the same general trend in the apparent lithium diffusion coefficient, 4-C > 2-C > C/2. The two techniques differed in the magnitude of the estimated diffusion coefficient by about a factor of 100. The observed increase in diffusion coefficient does not last over a large compositional range. Since the estimates from the method of Weppner and Huggins may contain artifacts due to the use of particulate electrodes and high charge rates, the method of Wang et al. may produce better values.

25 ENERGY STORAGE↗
DOE OSTI2026

Challenges in Pulsed-Field Gradient Nuclear Magnetic Resonance on Magnetically Heterogeneous Interfaces: Sequence and Field-Dependent Apparent Diffusion Coefficients

It is well known that the internal gradient (gi) that exists within pores haunts the diffusion coefficient (D) as measured by the pulsed-field gradient (PFG) nuclear magnetic resonance (NMR). Several PFG-NMR methods developed to determine an accurate D were not successful. Then, the steady-state diffusion coefficient (Dapp,8) for the cation [C4mim]+ of [C4mim][Tf2N]; [1-butyl-3-methylimidazolium][bis(trifluoromethylsulfonyl)imde] ionic liquid confined in ordered mesoporous carbon (OMC) were determined by comparing Dapp,8 obtained from 1H PFG-NMR performed with three different stimulated echo sequences: STE, APFG, and MPFG under the two external magnetic field strength, B0 = 9.4 and 14.1 Tesla. The measured Dapp,8 which is an order of magnitude smaller than D of bulk [C4mim][Tf2N], is in good agreement between APFG and MPFG both in B0 = 9.4 and 14.1 Tesla. However, the strong gi artifact, which caused apparent diffusion coefficient (Dapp) depending strongly and weakly on B0 and temperature, respectively, in diffusion-time dependent Dapp, Dapp(?) obtained from a sequence with monopolar gradients (STE) was suppressed by using sequences employing bipolar gradients (APFG and MPFG) in the region of steady-state diffusion. But incompletely suppressed gi artifact resulting in the different behaviors of the early part of Dapp(?) between the sequences leads a ˜ 0.6 and 0.9 in MPFG and APFG, respectively, in the relationship between mean squared displacement and diffusion time: = 2Dta, where a = 0.5 and 1 for 1-dimensional single file diffusion and 3-dimensional bulk diffusion, respectively. The above observations clearly show that the diffusion behavior of ions/molecules within the pores and pore structure, such as the surface-to-volume ratio? (D?_app (?)=D_0 [1-4/(9vp) S/V v(D_0 ?)]) and tortuosity (T = D0/Dapp,8), are possible to be misunderstood, especially in the systems with a non-negligible gi. This work demonstrates that it may be necessary to test several PFG sequences under multiple external magnetic fields for the correct determination of the diffusion behavior of ions/molecules in the pores with a larger internal gradient, gi.

Han, Kee Sung↗
NASA NTRS1973

Wave-induced eddy diffusion coefficients in the upper atmosphere of Mars.

A theory and method previously used to calculate terrestrial eddy diffusion coefficients due to instabilities in internal gravity waves have been extended to obtain wave-induced eddy diffusion coefficients in the upper atmosphere of Mars. If the Martian atmosphere is relatively dry (water vapor mixing ratio much less than .001), the effects of radiative damping are minimal for all but the longest-period waves. For greater concentrations of water vapor the effects of radiative damping are increased, but in any event it is reasonable to expect wave-induced turbulence, with eddy diffusion coefficients of the order of 10 to the 7th sq cm/sec in the Martian upper atmosphere.

Beasley, W. H.↗
DOE OSTI2024

Parallel Diffusion Coefficient of Energetic Charged Particles in the Inner Heliosphere from the Turbulent Magnetic Fields Measured by Parker Solar Probe

Diffusion coefficients of energetic charged particles in turbulent magnetic fields are a fundamental aspect of diffusive transport theory but remain incompletely understood. In this work, we use quasi-linear theory to evaluate the spatial variation of the parallel diffusion coefficient κ ∥ from the measured magnetic turbulence power spectra in the inner heliosphere. We consider the magnetic field and plasma velocity measurements from Parker Solar Probe made during Orbits 5–13. The parallel diffusion coefficient is calculated as a function of radial distance from 0.062 to 0.8 au, and the particle energy from 100 keV to 1 GeV. We find that κ ∥ increases exponentially with both heliocentric distance and energy of particles. The fluctuations in κ ∥ are related to the episodes of large-scale magnetic structures in the solar wind. By fitting the results, we also provide an empirical formula of κ ∥ = (5.16 ± 1.22) × 10 18 r 1.17 ± 0.08 E 0.71 ± 0.02 (cm 2 s -1 ) in the inner heliosphere, which can be used as a reference in studying the transport and acceleration of solar energetic particles as well as the modulation of cosmic rays.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1975

Calculated diffusion coefficients and the growth rate of olivine in a basalt magma

Concentration gradients in glass adjacent to skeletal olivines in a basalt have been examined by electron probe. The glass is depleted in Mg, Fe, and Cr and enriched in Si, Al, Na, and Ca relative to that far from olivine. Ionic diffusion coefficients for the glass compositions are calculated from temperature, ionic radius and melt viscosity, using the Stokes-Einstein relation. At 1170 C, the diffusion coefficient of Mg(2+) ions in the basalt is 4.5 billionths sq cm per sec. Comparison with measured diffusion coefficients in a mugearite suggests this value may be 16 times too small. The concentration gradient data and the diffusion coefficients are used to calculate instantaneous olivine growth rates. Growth necessarily preceded emplacement such that the composition of the crystals plus the enclosing glass need not be that of a melt. The computed olivine growth rates are compatible with the rate of crystallization deduced for the Skaegaard intrusion.

Donaldson, C. H.↗
DOE OSTI2024

Multitiered computational methodology for extracting three-dimensional rotational diffusion coefficients from x-ray photon correlation spectroscopy data without structural information

X-ray photon correlation spectroscopy (XPCS) is a powerful technique for analyzing particle systems by investigating their dynamics in suspensions across a broad range of temporal and spatial scales. This is done by illuminating samples with coherent x-ray beams and calculating the correlation function of the obtained x-ray scattering images. XPCS is uniquely suited for studying Brownian dynamics, consisting of translational and rotational diffusion. While traditional XPCS image analysis techniques can extract translational diffusion components, they are unable to estimate rotational diffusion coefficients. Here, we introduce a methodology that combines the angular-temporal cross-correlation analysis and a algorithmic framework called Multi-Tiered Estimation for Correlation Spectroscopy in 3D for estimating three-dimensional rotational diffusion coefficients from XPCS images of three-dimensional particle systems. We demonstrate our methodology for extracting rotational diffusion coefficients from XPCS data by applying it to simulated noisy x-ray images of systems of crossing nanotubes and proteins that evolve under translational and rotational Brownian motion for different diffusion rates. Furthermore, our results show that our approach determines rotational diffusion coefficients within a few percent error.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1982

On the energy dependence of the radial diffusion coefficient and spectra of inner radiation belt particles - Analytic solutions and comparison with numerical results

A theoretical method by which the energy dependence of the radial diffusion coefficient may be deduced from spectral observations of the particle population at the inner edge of the earth's radiation belts is presented. This region has previously been analyzed with numerical techniques; in this report an analytical treatment that illustrates characteristic limiting cases in the L shell range where the time scale of Coulomb losses is substantially shorter than that of radial diffusion (L approximately 1-2) is given. It is demonstrated both analytically and numerically that the particle spectra there are shaped by the energy dependence of the radial diffusion coefficient regardless of the spectral shapes of the particle populations diffusing inward from the outer radiation zone, so that from observed spectra the energy dependence of the diffusion coefficient can be determined. To insure realistic simulations, inner zone data obtained from experiments on the DIAL, AZUR, and ESRO 2 spacecraft have been used as boundary conditions. Excellent agreement between analytic and numerical results is reported.

Westphalen, H.↗