SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In this paper it is shown how some basic ideas from system theory and differential geometry can be used to establish some new results on the existence of periodic motion in autonomous feedback systems. The conditions are expressed in terms of the frequency response characteristic of the open-loop system and certain general properties of the nonlinearities.
This paper presents simple and accurate mathematical formulation for determining the ground location of remote sensor data. The techniques used are based on elementary concepts of differential geometry and lead to the development of a relation that gives location as a function of surface ellipticity, satellite position, velocity, attitude, and scanner orientation. The formula lends itself to simply computer coding and will hopefully lead to a standardization of the various techniques which have been developed to solve this problem.
Rod-beam theories are founded on hypotheses such as Bernouilli's suggesting flat cross-sections under deformation. These assumptions, which make rod-beam theories possible, also limit the accuracy of their analysis. It is shown that from a certain order upward terms of geometrically nonlinear deformations contradict the rod-beam hypotheses. Consistent application of differential geometry calculus also reveals differences from existing rod theories of higher order. These differences are explained by simple examples.
Certain principal normal curvatures of differential geometry were developed for use in curvature matrices associated with the asymptotic solution of electromagnetic diffraction problems. The effort is directed toward microwave antenna simulations and high speed digital computer analysis of radiometric instruments used to obtain soil moisture, sea state, salinity and temperature data. It is shown that the methods used to develop the principal normal curvatures for paraboloid, hyperboloid, ellipsoid, sphere, and cone can be applied to other radiometer geometries such as the parabolic torus, even though the surface parameterizations are different. It is concluded that deployable offset geometries, distorted by rotational forces and solar loads may be analyzed by similar means given a suitable surface description.
Differential ideals generated by sets of 2-forms which can be written with constant coefficients in a canonical basis of 1-forms are considered. By setting up a Cartan-Ehresmann connection, in a fiber bundle over a base space in which the 2-forms live, one finds an incomplete Lie algebra of vector fields in the fields in the fibers. Conversely, given this algebra (a prolongation algebra), one can derive the differential ideal. The two constructs are thus dual, and analysis of either derives properties of both. Such systems arise in the classical differential geometry of moving frames. Examples of this are discussed, together with examples arising more recently: the Korteweg-de Vries and Harrison-Ernst systems.
Until recently, there has not been any systematic effort towards a theory of systems with parameter variations. It is presently suggested that the concept of families of systems is basic to such an effort, and entails the techniques of Lie theory, differential geometry, and algebraic geometry. Attention is given to the geometric characterization of certain families of systems that appear in control and identification problems. The ways in which families of systems degenerate as parameter variations become large are isolated, using the topological rather than algebraic geometric case.
Already van Diggelen (1951) made use of the photometric function of a surface for the purpose of translating image variegation into slope and relief information, while the development of a method for producing a topographic map from a photometric image begins with Rindfleisch (1966). The term 'photoclinometry' was invented for the involved process. The present study is concerned with the adaptation of photoclinometry to radar imagery. The radar image as a candidate for photoclinometry offers both advantages and disadvantages when compared to ordinary optical images. The simplicity of the photometric function is the most obvious advantage. Attention is given to radiative transfer, the employment of differential geometry, and aspects of calibration.
The importance of differential geometry, particularly Lie brackets of vector fields, in the study of nonlinear systems is well established. Under very mild assumptions, it is shown that a real-analytic nonlinear system has an expansion in which the coefficients are computed in terms of Lie brackets. This expansion occurs in a special coordinate system. The concept of a pure feedback system is also explained. For control design involving a nonlinear system, one approach is to put the system in its canonical expansion and approximate by that part having only feedback paths.
An algorithm for describing range images based on Mean curvature (H) and Gaussian curvature (K) is presented. Range images are unique in that they directly approximate the physical surfaces of a real world 3-D scene. The curvature parameters are derived from the fundamental theorems of differential geometry and provides visible invariant pixel labels that can be used to characterize the scene. The sign of H and K can be used to classify each pixel into one of eight possible surface types. Due to the sensitivity of these parameters to noise the resulting HK-sing map does not directly identify surfaces in the range images and must be further processed. A region growing algorithm based on modeling the scene points with a Markov Random Field (MRF) of variable neighborhood size and edge models is suggested. This approach allows the integration of information from multiple characteristics in an efficient way. The performance of the proposed algorithm on a number of synthetic and real range images is discussed.
The process of connecting task descriptions originating from machine intelligence planning programs to the mechanization of feedback control of robot arms is analyzed. It is shown in this paper that control theories and practices can be extended to a higher level where feedback control of robot arms directly can respond to work space task commands provided that the work space task as a command is given in the form of a closed function of time. A general mathematical procedure using tools from differential geometry is introduced for synthesizing task space motion planning so that the planned motion can be used as a direct input to the robot arm feedback control system to achieve desired robot hand motion. By definition, 'intelligent control' is being manifested through robot performance in the task space relative to task space commands. Thus, the capability of implementing feedback control of robot arms directly driven by appropriate task descriptions in the workspace as commands is a step toward intelligent control.
The aim of this paper is to perform a theoretical study of the quadrupole term of the Ffowcs Williams-Hawkings (FW-H) equation to obtain practical results for applications to rotating blades. The quadrupole term of the FW-H equation is algebraically manipulated into volume, surface and line sources using generalized function theory and differential geometry. The volume source is of the type in Lighthill's jet noise theory. The surface sources are on the blade and shock surfaces and the line source is at the trailing edge. It is shown that contribution of volume sources in the boundary layer and wakes can be written in the form of surface integrals. It is argued that the surface and line sources and the part of the volume sources in the boundary layer, wakes and vortices near the blades should be sufficient in calculation of the noise of high speed rotating blades. The integrals correspoding to the various sources appearing in the formula for calculation of the acoustic pressure are briefly derived.
The development of an approach to the visual perception of object surface information using laser range data in support of robotic grasping is discussed. This is a very important problem area in that a robot such as the EVAR must be able to formulate a grasping strategy on the basis of its knowledge of the surface structure of the object. A description of the problem domain is given as well as a formulation of an algorithm which derives an object surface description adequate to support robotic grasping. The algorithm is based upon concepts of differential geometry namely, Gaussian and mean curvature.
A theory is presented for computing waves radiated from waves on a smooth surface. With the assumption that attention of the surface wave is due only to radiation and not to dissipation in the surface material, the radiation coefficient is derived in terms of the attenuation factor. The excitation coefficient is determined by the reciprocity condition. Formulas for the shape and the spreading of the radiated wave are derived, and some sample calculations are presented. An investigation of resonant phase matching for nonseparable surfaces is presented with a sample calculation. A discussion of how such calculations might be related to resonant frequencies of nonseparable thin shell structures is included. A description is given of nonseparable surfaces that can be modeled in the vector that facilitates use of the appropriate formulas of differential geometry.
A new approach to modeling gear tooth surfaces is discussed. A computer graphics solid modeling procedure is used to simulate the tooth fabrication process. This procedure is based on the principles of differential geometry that pertain to envelopes of curves and surfaces. The procedure is illustrated with the modeling of spur, helical, bevel, spiral bevel, and hypoid gear teeth. Applications in design and manufacturing are discussed. Extensions to nonstandard tooth forms, to cams, and to rolling element bearings are proposed.
An approach to the control of constrained dynamic systems such as multiple arm systems, multifingered grippers, and walking vehicles is described. The basic philosophy is to utilize a minimal set of inputs to control the trajectory and the surplus input to control the constraint or interaction forces and moments in the closed chain. A dynamic control model for the closed chain is derived that is suitable for designing a controller in which the trajectory and the interaction forces and moments are explicitly controlled. Nonlinear feedback techniques derived from differential geometry are then applied to linearize and decouple the nonlinear model. These ideas are illustrated through a planar example in which two arms are used for cooperative manipulation. Results from a simulation are used to illustrate the efficacy of the method.
Shapes of gear teeth produced by gear cutters of specified shape simulated computationally, according to approach based on principles of differential geometry. Results of computer simulation displayed as computer graphics and/or used in analyses of design, manufacturing, and performance of gears. Applicable to both standard and non-standard gear-tooth forms. Accelerates and facilitates analysis of alternative designs of gears and cutters. Simulation extended to study generation of surfaces other than gears. Applied to cams, bearings, and surfaces of arbitrary rolling elements as well as to gears. Possible to develop analogous procedures for simulating manufacture of skin surfaces like automobile fenders, airfoils, and ship hulls.
This study will demonstrate the importance of application of computer numerically controlled (CNC) machines in generation of gear tooth surfaces with new topology. This topology decreases gear vibration and will extend the gear capacity and service life. A preliminary investigation by a tooth contact analysis (TCA) program has shown that gear tooth surfaces in line contact (for instance, involute helical gears with parallel axes, worm gear drives with cylindrical worms, etc.) are very sensitive to angular errors of misalignment that cause edge contact and an unfavorable shape of transmission errors and vibration. The new topology of gear tooth surfaces is based on the localization of bearing contact, and the synthesis of a predesigned parabolic function of transmission errors that is able to absorb a piecewise linear function of transmission errors caused by gear misalignment. The report will describe the following topics: description of kinematics of CNC machines with six degrees of freedom that can be applied for generation of gear tooth surfaces with new topology. A new method for grinding of gear tooth surfaces by a cone surface or surface of revolution based on application of CNC machines is described. This method provides an optimal approximation of the ground surface to the given one. This method is especially beneficial when undeveloped ruled surfaces are to be ground. Execution of motions of the CNC machine is also described. The solution to this problem can be applied as well for the transfer of machine tool settings from a conventional generator to the CNC machine. The developed theory required the derivation of a modified equation of meshing based on application of the concept of space curves, space curves represented on surfaces, geodesic curvature, surface torsion, etc. Condensed information on these topics of differential geometry is provided as well.
A modeling method for analyzing the three-dimensional thermal behavior of spiral bevel gears has been developed. The model surfaces are generated through application of differential geometry to the manufacturing process for face-milled spiral bevel gears. Contact on the gear surface is found by combining tooth contact analysis with three-dimensional Hertzian theory. The tooth contact analysis provides the principle curvatures and orientations of the two surfaces. This information is then used directly in the Hertzian analysis to find the contact size and maximum pressure. Heat generation during meshing is determined as a function of the applied load, sliding velocity, and coefficient of friction. Each of these factors change as the point of contact changes during meshing. A nonlinear finite element program was used to conduct the heat transfer analysis. This program permitted the time- and position-varying boundary conditions, found in operation, to be applied to a one-tooth model. An example model and analytical results are presented.