SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Kinetics and energetics of condensed phase thermal decomposition reactions of ammonium perchlorate composite propellants analyzed, using differential scanning calorimetry
Cassini/CIRS spectra in the far- and mid-infrared region are used to determine the abundance of methanein Titans lower stratosphere and investigate its distribution with latitude. The CIRS spectra include emissionfrom both the CH4 v4 band at 7.7 micron and pure rotational lines longwards of 50 micron, which show differential sensitivities to thermal profile and methane mole fraction. We analyze nadir and limb data taken over the first part of the Cassini mission (August 2005 to June 2010), including a selection of 12 latitudes that provides a reasonably complete and regular sampling of both hemispheres. Unexpectedly, but in a consistent manner for limb and nadir geometries, large variations of the methane mole fraction near 15 mbar (approx. 85 km) are found, with values ranging from approx. 1.0% (at low latitudes and near +/-50-55 deg) to approx. 1.5% (at +/-30-35 deg and polar latitudes). Error bars on the retrieved methane mole fraction are 0.07-0.12% at low latitudes in the Southern hemisphere and 0.14-0.21% northward of 40 deg N. A 1.0% methanemole fraction at low latitudes permits us to reconcile the HASI-measured temperatures below 147 kmaltitude (2.7 mbar) with inferences from CIRS. The roughly hemispherically-symmetric distribution ofmethane gas is reminiscent of that observed or predicted for the tropospheric methane clouds, whichon a yearly-averaged basis, show preferential occurrences at tropical and polar latitudes. We speculatethat convective events at these latitudes result into local stratospheric methane enrichment, whichmay persist year-round due to dynamical mixing times in the lower stratosphere only moderately shorterthan a Titan year.
The Mars 2007 Phoenix Scout Mission successfully landed on May 25, 2008 and operated on the northern plains of Mars for 150 sols. The primary mission objective was to study the history of water and evaluate the potential for past and present habitability in Martian arctic ice-rich soil [1]. Phoenix landed near 68 N latitude on polygonal terrain created by ice layers that are a few centimeters under loose soil materials. The Phoenix Mission is assessing the potential for habitability by searching for organic molecules in the ice or icy soils at the landing site. Organic molecules are necessary building blocks for life, although their presence in the ice or soil does not indicate life itself. Phoenix searched for organic molecules by heating soil/ice samples in the Thermal and Evolved-Gas Analyzer (TEGA, [2]). TEGA consists of 8 differential scanning calorimeter (DSC) ovens integrated with a magnetic-sector mass spectrometer with a mass range of 2-140 daltons [2]. Endothermic and exothermic reactions are recorded by the TEGA DSC as samples are heated from ambient to ~1000 C. Evolved gases, including any organic molecules and their fragments, are simultaneously measured by the mass spectrometer during heating. Phoenix TEGA data are still under analysis; however, no organic fragments have been identified to date in the evolved gas analysis (EGA). The MECA Wet Chemistry Lab (WCL) discovered a perchlorate salt in the Phoenix soils and a mass 32 peak evolved between 325 and 625 C for one surface sample dubbed Baby Bear [3]. The mass 32 peak is attributed to evolved O2 generated during the thermal decomposition of the perchlorate salt. Perchlorates are very strong oxidizers when heated, so it is possible that organic fragments evolved in the temperature range of 300-600 C were combusted by the O2 released during the thermal decomposition of the perchlorate salt. The byproduct of the combustion of organic molecules is CO2. There is a prominent release of CO2 between 200-600 C for several of the Phoenix soils analyzed by TEGA. This low temperature release of CO2 might be any combination of 1) desorption of adsorbed CO2, 2) thermal decomposition of Fe- and Mg-carbonates, and 3) combustion of organic molecules [2].
The enhanced control over microstructural evolution inherent in rapid solidification processing techniques are exploited to create novel ceramic magnetic materials. The great sensitivity of magnetic properties to local structure provides a powerful probe both for the study of structure and of microscopic solidification mechanisms. The first system studied is the SrO-Fe2O3 binary, which contains the commercially important hard magnetic compound strontium hexaferrite. The products were analyzed by transmission electron microscopy, Mossbauer spectroscopy, magnetic measurements, and differential thermal analysis. As-quenched ribbons contain high concentrations of super-paramagnetic particles, 80 to 250 Angstroms in diameter, in a glassy matrix. This suggests the possibility of crystallizing monodomain strontium hexaferrite during subsequent heat treatment, with a resulting increase in coercivity over conventionally processed ferrite magnets. That magnetic properties can be controlled in solidification processing by varying the quench rate is demonstrated.
The Mars 2007 Phoenix Scout Mission successfully launched on August 4, 2007, for a 10-month journey to Mars. The Phoenix spacecraft is scheduled to land on May 25, 2008. The primary mission objective is to study the history of water and evaluate the potential for past and present habitability in Martian arctic ice-rich soil [1]. Phoenix will land near 68 N latitude on polygonal terrain presumably created by ice layers that are expected to be a few centimeters under loose soil materials [2,3]. The Phoenix Mission will assess the potential for habitability by searching for organic molecules in ice or icy soils at the landing site. Organic molecules are necessary building blocks for life, although their presence in the ice or soil does not indicate life itself. Phoenix will search for organic molecules by heating soil/ice samples in the Thermal and Evolved-Gas Analyzer (TEGA, [4]). TEGA consists of 8 differential scanning calorimeter (DSC) ovens integrated with a magnetic-sector mass spectrometer with a mass range of 2-140 daltons [4]. Endothermic and exothermic reactions are recorded by the TEGA DSC as samples are heated from ambient to approx.1000 C. Evolved gases, including organic molecules and fragments if present, are simultaneously measured by the mass spectrometer during heating.
This study investigates the mechanical properties and interfacial bonding of Polyamide 12 filled with Glass Fiber (PA12/GF) lattice structures overmolded with Nylon 66 (PA66) and Thermoplastic Polyurethane (TPU). The PA12/GF lattices, designed in Gyroid, Isotruss, and Octahedral geometries, were produced using the Selective Laser Sintering (SLS) technique. The thermal characteristics of both the lattice and overmolding materials were analyzed using Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA). The mechanical performance and interfacial bonding were evaluated through mechanical testing and microstructural analysis. The results indicate that overmolding improved flexural strength and impact resistance of the PA12/GF lattices. For instance, the plain PA12/GF Isotruss lattice exhibited a flexural strength of 15.5 MPa. By overmolding it with TPU the flexural strength increased by up to 137%, while PA66-overmolding resulted in an increase of 371%, achieving a flexural strength of 73 MPa. In terms of impact resistance, TPU-overmolding improved performance significantly, with an increase of 1800% (Gyroid) compared to the plain lattice. Microstructural analysis revealed good adhesion at the interface, especially when both the lattice and overmolding materials were thoroughly dried prior to the overmolding process to minimize interfacial porosity. This study highlights the potential of using overmolding to enhance lattice structures performance, offering lightweight and cost-efficient solutions for automotive applications.
Volatile-bearing minerals (e.g., Fe-oxyhydroxides, phyllosilicates, carbonates, and sulfates) may be important phases on the surface of Mars. In order to characterize these potential phases the Thermal Evolved-Gas Analyzer (TEGA), which was onboard the Mars Polar Lander, was to have performed differential scanning calorimetry (DSC) and evolved-gas analysis of soil samples collected from the surface. The sample chamber in TEGA operates at about 100 mbar (approximately 76 torr) with a N2, carrier gas flow of 0.4 seem. Essentially, no information exists on the effects of reduced pressure on the thermal properties of volatile-bearing minerals. In support of TEGA, we have constructed a laboratory analog for TEGA from commercial instrumentation. We connected together a commercial differential scanning calorimeter, a quadruple mass spectrometer, a vacuum pump, digital pressure gauge, electronic mass flow meter, gas "K" bottles, gas dryers, and high and low pressure regulators using a collection of shut off and needle valves. Our arrangement allows us to vary and control the pressure and carrier gas flow rate inside the calorimeter oven chamber.
The Comet Rendezvous Asteroid Flyby Mission (CRAF) is described. After gravity assists from Venus and Earth, the spacecraft will fly by the asteroid 46 Hestia en route to a rendezvous with P/Tempel 2 in Nov. 1996, when the comet is near aphelion. The scientific experiments for the CRAF mission are: an imaging system; a visual and infrared mapping spectrometer; an infrared radiometer; a penetrator carrying a gamma-ray spectrometer, a scanning differential calorimeter and evolved gas analyzer, accelerometers, and temperature probes; a neutral gas and thermal ion mass spectrometer; a secondary ion mass spectrometer for analyzing dust, gas, and thermal ions; a scanning electron microscope and particle analyzer; an X-ray fluorescence and gas chromatographic analyzer for collected dust and ice samples; a dust counter and velocity analyzer; a retarding potential ion mass spectrometer; a supra-thermal ion mass spectrometer and electron analyzer; a magnetometer; and a coordinated radio, electron, and plasma wave analyzer.
The Thermal Evolved-Gas Analyzer (TEGA) instrument onboard the 2007 Phoenix Lander will perform differential scanning calorimetry (DSC) and evolved-gas analysis of soil samples collected from the surface. Data from the instrument will be compared with Mars analog mineral standards, collected under TEGA Mars-like conditions to identify the volatile-bearing mineral phases [1] (e.g., Fe-oxyhydroxides, phyllosilicates, carbonates, and sulfates) found in the Martian soil. Concurrently, the instrument will be looking for indications of organics that might also be present in the soil. Organic molecules are necessary building blocks for life, although their presence in the ice or soil does not indicate life itself. The spacecraft will certainly bring organic contaminants to Mars even though numerous steps were taken to minimize contamination during the spacecraft assembly and testing. It will be essential to distinguish possible Mars organics from terrestrial contamination when TEGA instrument begins analyzing icy soils. To address the above, an Organic Free Blank (OFB) was designed, built, tested, and mounted on the Phoenix spacecraft providing a baseline for distinguishing Mars organics from terrestrial organic contamination. Our objective in this report is to describe some of the considerations used in selecting the OFB material and then report on the processing and analysis of the final candidate material
The Mars Phoenix Scout Mission with its diverse instrument suite successfully examined several soils on the Northern plains of Mars. The Thermal and Evolved Gas Analyzer (TEGA) was employed to detect organic and inorganic materials by coupling a differential scanning calorimeter (DSC) with a magnetic-sector mass spectrometer (MS). Martian soil was heated up to 1000 C in the DSC ovens and evolved gases from mineral decomposition products were examined with the MS. TEGA s DSC has the capability to detect endothermic and exothermic reactions during heating that are characteristic of minerals present in the Martian soil. Initial TEGA results indicated the presence of endothermic peaks with onset temperatures that ranged from 675 C to 750 C with corresponding CO2 release. This result suggests the presence of calcite (CaCO3. CaO + CO2). Organic combustion to CO2 is not likely since this mostly occurs at temperatures below 550 C. Fe-carbonate and Mg-carbonate are not likely because their decomposition temperatures are less than 600 C. TEGA enthalpy determinations suggest that calcite, may occur in the Martian soil in concentrations of approx.1 to 5 wt. %. The detection of calcite could be questioned based on previous results that suggest Mars soils are mostly acidic. However, the Phoenix landing site soil pH was measured at pH 8.3 0.5, which is typical of terrestrial soils where pH is controlled by calcite solubility. The range of onset temperatures and calcite concentration as calculated by TEGA is poorly con-strained in part because of limited thermal data of cal-cite at reduced pressures. TEGA operates at <30 mbar while most calcite literature thermal data was obtained at 1000 mbar or higher pressures.
The present study investigates the thermal stability and thermal expansion behavior of seven equi-atomic refractory multi-principal element alloys (MPEAs) based on the MoNbTi ternary system composed of low neutron absorption cross section elements. Through an integrated approach utilizing in-situ high-temperature X-ray diffraction (HT-XRD) in conjunction with differential scanning calorimetry (DSC), dilatometry and ageing heat treatment, the thermal stability of the MPEAs was comprehensively analyzed. In-situ HT-XRD experiment confirmed the stability of the room temperature phases up to 1000 °C with no peaks observed corresponding to additional phases in the HT-XRD patterns at 500, 800 and 1100 °C. DSC thermograms showed the absence of peaks up to 1000 °C, while peaks and valleys corresponding to exothermic and endothermic events were observed above 1000 °C. Coefficient of thermal expansion (CTE) derived from second order polynomial fitting of linear thermal expansion data from the dilatometry experiment showed linear increment up to 1000 °C for all the alloys except those containing Zr. The Cr containing alloys exhibited notably higher CTE values, particularly the Al containing alloy exhibited the highest value. Ageing heat treatment at 800 and 1000 °C for 96 h and subsequent microstructural analysis revealed significant precipitation of secondary phases in MoNbTiZr, MoNbTiZrV and MoNbTiCrAl. In conclusion, a substantial increase in hardness was observed in MoNbTiZr and MoNbTiCrAl due to secondary phase precipitation, while the other alloys maintained hardness values comparable to their as-cast and homogenized states.
The Thermal and Evolved Gas Analyzer (TEGA) instrument scheduled to fly onboard the 2007 Mars Phoenix Scout Mission will perform differential scanning calorimetry (DSC) and evolved gas analysis (EGA) of soil samples and ice collected from the surface and subsurface at a northern landing site on Mars. We have been developing a sample characterization data library using a laboratory DSC integrated with a quadrupole mass spectrometer to support the interpretations of TEGA data returned during the mission. The laboratory TEGA test-bed instrument has been modified to operate under conditions similar to TEGA, i.e., reduced pressure (e.g., 100 torr) and reduced carrier gas flow rates. We have previously developed a TEGA data library for a variety of volatile-bearing mineral phases, including Fe-oxyhydroxides, phyllosilicates, carbonates, and sulfates. Here we examine the thermal and evolved gas properties of samples that contain organics. One of the primary objectives of the Phoenix Scout Mission is to search for habitable zones by assessing organic or biologically interesting materials in icy soil. Nitrogen is currently the carrier gas that will be used for TEGA. In this study, we examine two possible modes of detecting organics in geologic samples; i.e., pyrolysis using N2 as the carrier gas and combustion using O2 as the carrier gas.
In the first practical application of laser anemometry to an actual gas turbine engine combustor, the mean velocity and turbulent intensity profiles were measured in a steady-flow combustion rig across an annulus simulating a turbine inlet; to establish a basis for comparison with similar measurements to be made in an operating engine and to confirm current turbine aerodynamics and heat transfer design assumptions. It was necessary to develop a new experimental technique for traversing the annulus due to differential thermal expansion of the cantilevered combustion rig and a new computer-graphics analysis technique for analyzing the velocity histograms due to the high background light intensity. The axial mean velocity and turbulent intensity were uniform across the annulus under all operating conditions and the flow had little or no swirl component. The isothermal mean velocity was doubled by the burning of fuel, however, the isothermal turbulent intensity was relatively unaffected.
This study entails the third part of a global flare energetics project, in which Ramaty High-Energy Solar Spectroscopic Imager (RHESSI) data of 191 M and X-class flare events from the first 3.5 years of the Solar Dynamics Observatory mission are analyzed. We fit a thermal and a nonthermal component to RHESSI spectra, yielding the temperature of the differential emission measure (DEM) tail, the nonthermal power-law slope and flux, and the thermal nonthermal cross-over energy eco. From these parameters, we calculate the total nonthermal energy E(sub nt) in electrons with two different methods: (1) using the observed cross-over energy e(sub co) as low-energy cutoff, and (2) using the low-energy cut off e(sub wt) predicted by the warm thick-target bremsstrahlung model of Kontar et al. Based on a mean temperature of T(sub e) = 8.6 MK in active regions, we find low-energy cutoff energies of e(sub wt) = 6.2 +/-1.6 keV for the warm-target model, which is significantly lower than the cross-over energies e(sub co) = 21 +/- 6 keV. Comparing with the statistics of magnetically dissipated energies E(sub mag) and thermal energies E(sub th) from the two previous studies, we find the following mean (logarithmic) energy ratios with the warm-target model: E(sub nt) = 0.41E(sub mag), E(sub th) = 0.08 E(sub mag), and E(sub th) = 0.15 E(sub nt). The total dissipated magnetic energy exceeds the thermal energy in 95% and the nonthermal energy in 71% of the flare events, which confirms that magnetic reconnection processes are sufficient to explain flare energies. The nonthermal energy exceeds the thermal energy in 85% of the events, which largely confirms the warm thick-target model.
SINDA, Systems Improved Numerical Differencing Analyzer, software system developed for solving physical problems governed by diffusion-type equations modeled by lumped-parameter representations. Used as general thermal analyzer with resistor-and-capacitor-network representations, adapted to wide range of problems represented by such differential equations as Fourier, Poisson, or LaPlace. Software system updated. FLUINT, FLUid INTegrator, is advanced, one-dimensional fluid-analysis program solving equations of arbitrary fluid-flow networks. Written in FORTRAN and ASSEMBLER.
The brightness curve of a comet is analyzed in terms of porosity and nature of volatiles in its nucleus. Mobility of pores, densification, phase changes, differential thermal expansion and heat flow into and out of the nucleus are discussed leading to a method for estimating the effective heat conductivity and porosity of the nucleus. The method is applied to comets P/Giacobini-Zinner, P/Halley, P/Kopff, P/Encke, P/Tempel 2 and P/d'Arrest.
Tasks performed in this project were defined in a September 9, 1994 meeting of representatives of Vatell, NASA Lewis and Virginia Tech. The overall objective agreed upon in the meeting was 'to demonstrate the viability of thin film techniques for heat flux and temperature sensing in HYSTEP thermal protection systems'. We decided to attempt a combination of NASA's and Vatell's best heat flux sensor technology in a sensor which would be tested in the Vortek facility at Lewis early in 1995. The NASA concept for thermocouple measurement of surface temperature was adopted, and Vatell methods for fabrication of sensors on small diameter substrates of aluminum nitride were used to produce a sensor. This sensor was then encapsulated in a NARloy-Z housing. Various improvements to the Vatell substrate design were explored without success. The basic NASA and Vatell sensor layouts were analyzed by finite element modeling, in an attempt to better understand the effects of material properties, dimensions and thermal differential element location on sensor symmetry, bandwidth and sensitivity. This analysis showed that, as long as the thermal resistivity of the thermal differential element material is much larger (10X) than that of the substrate material, the simplest arrangement of layer is best. During calibration of the sensor produced in this project, undesirable side-effects of combining the heat flux and temperature sensor return leads were observed. The sensor did not cleanly separate the heat flux and temperature signals, as sensors with four leads have consistently done before. Task 7 and 8 discussed in the meeting will be performed with a continuation of funding in 1995. The following is a discussion of each of the tasks performed as outlined in the statement of work dated september 26, 1994. Task 1A was added to cover further investigation into the NASA sensor concept.
Spectroscopic analyses have shown that smectites enhanced in the laboratory with additional ferric species exhibit important similarities to those of the soils on Mars. Ferrihydrite in these chemically treated smectites has features in the visible to near-infrared region that resemble the energies and band strengths of features in reflectance spectra observed for several bright regions on Mars. New samples have been prepared with sulfate as well, because S was found by Viking to be a major component in the surface material on Mars. A suite of ferrihydrite-bearing and ferric sulfate-bearing montmorillonites, prepared with variable Fe3+ and S concentrations and variable pH conditions, has been analyzed using reflectance spectroscopy in the visible and infrared regions, Mossbauer spectroscopy at room temperature and 4 K, differential thermal analysis, and X-ray diffraction. These analyses support the formation of ferrihydrite of variable crystallinity in the ferrihydrite-bearing montmorillonites and a combination of schwertmannite and ferrihydrite in the ferric sulfate-bearing montmorillonites. Small quantities of poorly crystalline or nanophase forms of other ferric materials may also be present in these samples. The chemical formation conditions of the ferrihydrite-bearing and ferric sulfate-bearing montmorillonites influence the character of the low temperature Mossbauer sextets and the visible reflectance spectra. An absorption minimum is observed at 0.88-0.89 micrometers in spectra of the ferric sulfate-bearing samples, and at 0.89-0.92 micrometers in spectra of the ferrihydrate-bearing montmorillonites. Mossbauer spectra of the ferric sulfate-bearing montmorillonites indicate variable concentrations of ferrihydrite and schwertmannite in the interlaminar spaces and along grain surfaces. Dehydration under reduced atmospheric pressure conditions induces a greater effect on the adsorbed and interlayer water in ferrihydrite-bearing montmorillonite than on the water in ferric sulfate-bearing montmorillonite. Reflectance spectra of ferric sulfate-bearing montmorillonite include a strong 3-micrometers band that is more resistant to dry atmospheric conditions than the 3-micrometers band in spectra of similarly prepared ferrihydrite-bearing montmorillonites.