Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Boundary Layer Profiles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Laser transit anemometer measurements on a slender cone in the Langley unitary plan wind tunnel

A laser transit anemometer (LTA) system was used to probe the boundary layer on a slender (5 degree half angle) cone model in the Langley unitary plan wind tunnel. The anemometer system utilized a pair of laser beams with a diameter of 40 micrometers spaced 1230 micrometers apart to measure the transit times of ensembles of seeding particles using a cross-correlation technique. From these measurements, boundary layer profiles around the model were constructed and compared with CFD calculations. The measured boundary layer profiles representing the boundary layer velocity normalized to the edge velocity as a function of height above the model surface were collected with the model at zero angle of attack for four different flow conditions, and were collected in a vertical plane that bisected the model's longitudinal center line at a location 635 mm from the tip of the forebody cone. The results indicate an excellent ability of the LTA system to make velocity measurements deep into the boundary layer. However, because of disturbances in the flow field caused by onboard seeding, premature transition occurred implying that upstream seeding is mandatory if model flow field integrity is to be maintained. A description and results of the flow field surveys are presented.

Humphreys, William M., Jr.↗
NASA NTRS2001

Experimental Evaluation of the Effect of Angle-of-attack on the External Aerodynamics and Mass Capture of a Symmetric Three-engine Air-breathing Launch Vehicle Configuration at Supersonic Speeds

A subscale aerodynamic model of the GTX air-breathing launch vehicle was tested at NASA Glenn Research Center's 10- by 10-Foot Supersonic Wind Tunnel from Mach 2.0 to 3.5 at various angles-of-attack. The objective of the test was to investigate the effect of angle-of-attack on inlet mass capture, inlet diverter effectiveness, and the flowfield at the cowl lip plane. The flow-through inlets were tested with and without boundary-layer diverters. Quantitative measurements such as inlet mass flow rates and pitot-pressure distributions in the cowl lip plane are presented. At a 3deg angle-of-attack, the flow rates for the top and side inlets were within 8 percent of the zero angle-of-attack value, and little distortion was evident at the cowl lip plane. Surface oil flow patterns showing the shock/boundary-layer interaction caused by the inlet spikes are shown. In addition to inlet data, vehicle forebody static pressure distributions, boundary-layer profiles, and temperature-sensitive paint images to evaluate the boundary-layer transition are presented. Three-dimensional parabolized Navier-Stokes computational fluid dynamics calculations of the forebody flowfield are presented and show good agreement with the experimental static pressure distributions and boundary-layer profiles. With the boundary-layer diverters installed, no adverse aerodynamic phenomena were found that would prevent the inlets from operating at the required angles-of-attack. We recommend that phase 2 of the test program be initiated, where inlet contraction ratio and diverter geometry variations will be tested.

Kim, Hyun D.↗
NASA NTRS1990

The effect of small-scale roughness on the main flow profile of a laminar boundary layer

The profile distortion due to a single roughness element, to two such elements, and to many elements is investigated. Signal-averaging of the velocity difference due to the roughness being alternately present or absent is employed in order to improve accuracy. The primary objective of examining the distributed-roughness profiles for any evidence of instability-enhancing form is not met, but the results are reconsidered, and relevant hypotheses and suggestions are presented. It is noted that the reason for not meeting the objective of estimating Tollmien-Schlichting amplification from rough-wall profiles is that much of the distortion occurs close to the wall and below the element tops.

Kendall, James M., Jr.↗
NASA NTRS2011

Base Heating Sensitivity Study for a 4-Cluster Rocket Motor Configuration in Supersonic Freestream

In support of launch vehicle base heating and pressure prediction efforts using the Loci-CHEM Navier-Stokes computational fluid dynamics solver, 35 numerical simulations of the NASA TND-1093 wind tunnel test have been modeled and analyzed. This test article is composed of four JP-4/LOX 500 lbf rocket motors exhausting into a Mach 2 - 3.5 wind tunnel at various ambient pressure conditions. These water-cooled motors are attached to a base plate of a standard missile forebody. We explore the base heating profiles for fully coupled finite-rate chemistry simulations, one-way coupled RAMP (Reacting And Multiphase Program using Method of Characteristics)-BLIMPJ (Boundary Layer Integral Matrix Program - Jet Version) derived solutions and variable and constant specific heat ratio frozen flow simulations. Variations in turbulence models, temperature boundary conditions and thermodynamic properties of the plume have been investigated at two ambient pressure conditions: 255 lb/sq ft (simulated low altitude) and 35 lb/sq ft (simulated high altitude). It is observed that the convective base heat flux and base temperature are most sensitive to the nozzle inner wall thermal boundary layer profile which is dependent on the wall temperature, boundary layer s specific energy and chemical reactions. Recovery shock dynamics and afterburning significantly influences convective base heating. Turbulence models and external nozzle wall thermal boundary layer profiles show less sensitivity to base heating characteristics. Base heating rates are validated for the highest fidelity solutions which show an agreement within +/-10% with respect to test data.

Mehta, Manish↗
NASA NTRS1972

An experimental investigation of vortex generation in a turbulent boundary layer undergoing adverse pressure gradient

The existence of streamwise vortices in nominally 2-dimensional boundary layers undergoing adverse pressure gradient was investigated. The free stream Mach number was 5.75, the wall to stagnation temperature ratio was 0.63 and the Reynolds number based on free stream conditions was 3.9 x 10 to the 7th power/ft. The model consisted of an axisymmetric compression flare preceded by a cylindrical axially symmetric body. A natural turbulent boundary layer was established well ahead of the compression region. Boundary layer profiles of static pressure, pitot pressure, and stagnation temperature were taken at a surface station with a local inclination of 20 deg. Profile measurements were obtained at various peripheral stations. The measurements revealed zero peripheral variations at the surface of the body and at the edge of the boundary layer. However, distinct wavy pressure variations were observed within the boundary layer profiles, indicating the existence of longitudinal vortex cells within the boundary layer.

Zakkay, V.↗
NASA NTRS1991

Computational analysis of plume induced separation

Full Navier-Stokes simulations around axisymmetric boattailed and flared rockets are numerically investigated for plume induced separation phenomenon. At lower altitudes, the plume interaction with the external flow does not cause any flow separation on the body, but at conditions corresponding to higher altitudes large plume induced separation is observed. Addition of a flare to the afterbody limits the extent of separation at high altitudes. Computational solutions for the boattailed axisymmetric geometry are compared with available wind-tunnel and flight data. The effect of forebody ablation is studied by modifying the inflow boundary layer profile. Numerical solutions with thicker boundary layers show significantly greater plume-induced separation compared with nonablating cases. Heat transfer to the wall was computed for the flared afterbody geometry and is presented.

Venkatapathy, Ethiraj↗
NASA NTRS1972

Turbulent boundary-layer velocity profiles on a nonadiabatic at Mach number 6.5

Velocity profiles were obtained from pitot-pressure and total-temperature measurements within a turbulent boundary layer on a large sharp-edged flat plate. Momentum-thickness Reynolds number ranged from 2590 to 8860 and wall-to-adiabatic-wall temperature ratios ranged from 0.3 to 0.5. Measurements were made both with and without boundary layer trips. Five methods are evaluated for correlating the measured velocity profiles with the incompressible law-of-the-wall and the velocity defect law. The mixing-length generalization of Van Driest gives the best correlation.

Keener, E. R.↗
NASA NTRS1983

Higher modes of the Orr-Sommerfeld problem for boundary layer flows

The discrete spectrum of the Orr-Sommerfeld problem of hydrodynamic stability for boundary layer flows in semi-infinite regions is examined. Related questions concerning the continuous spectrum are also addressed. Emphasis is placed on the stability problem for the Blasius boundary layer profile. A general theoretical result is given which proves that the discrete spectrum of the Orr-Sommerfeld problem for boundary layer profiles (U(y), 0,0) has only a finite number of discrete modes when U(y) has derivatives of all orders. Details are given of a highly accurate numerical technique based on collocation with splines for the calculation of stability characteristics. The technique includes replacement of 'outer' boundary conditions by asymptotic forms based on the proper large parameter in the stability problem. Implementation of the asymptotic boundary conditions is such that there is no need to make apriori distinctions between subcases of the discrete spectrum or between the discrete and continuous spectrums. Typical calculations for the usual Blasius problem are presented.

Lakin, W. D.↗
NASA NTRS1989

The development of crossflow vortices on a 45 degree swept wing

Three-dimensional boundary-layer experiments are currently being conducted on a 45 deg swept wing in the Arizona State University Unsteady Wind Tunnel. Crossflow-dominated transition is produced via a model with contoured end liners to simulate infinite swept-wing flow. Fixed-wavelength stationary and traveling crossflow vortex are observed. The stationary vortex wavelengths vary with Reynolds number as predicted by linear-stability theory, but with observed wavelengths which are about 25 percent smaller than theoretically predicted. The frequencies of the most-amplified moving waves are in agreement with linear-stability theory; traveling waves at higher frequencies than predicted are also observed. These higher-frequency waves may be harmonics of the primary crossflow waves generated by a parametric resonance phenomena. Boundary-layer profiles measured at several spanwise locations show streamwise disturbance profiles characteristic of the crossflow instability. Near the transition location, severe distortions of the laminar boundary-layer profiles are observed. Mean-profile measurements are compared to theoretical predictions.

Mousseux, Marc C.↗
NASA NTRS1994

Transition correlations in three-dimensional boundary layers

The stability and transition characteristics of three-dimensional boundary-layer flows are examined. First, the flow over a rotating cone is considered computationally. An increase of stagnation temperature is found to be only slightly stabilizing. Parameter studies on the simple rotating-cone geometry provide a large database of three-dimensional boundary-layer profiles and associated stability characteristics. To determine the possibility of correlating transition location with parameters based purely on basic-state three-dimensional boundary-layer profile characteristics, an empirical transition location of N = 9 is assumed. Transition location does not correlate with the traditional crossflow Reynolds number. A more appropriate definition for crossflow Reynolds number is found and termed R(sub cf(new)). This new parameter appears to correlate for transition location when plotted against maximum crossflow velocity. Then, the flow over a yawed cone is considered experimentally. The correlation results obtained from the rotating-cone work are applied to the actual measured transition locations on two different yawed-cone models under various angle-of-attack conditions in two different experimental facilities and are verified. This correlation is only suggested as a tool for preliminary transition prediction and design in three-dimensional boundary layers; once a preliminary shape is selected, further linear stability theory or parabolized stability equation calculations are strongly urged.

Reed, Helen L.↗
NASA NTRS1992

Numerical studies of transverse curvature effects on transonic flow stability

A numerical study of transverse curvature effects on compressible flow temporal stability for transonic to low supersonic Mach numbers is presented for axisymmetric modes. The mean flows studied include a similar boundary-layer profile and a nonsimilar axisymmetric boundary-layer solution. The effect of neglecting curvature in the mean flow produces only small quantitative changes in the disturbance growth rate. For transonic Mach numbers (1-1.4) and aerodynamically relevant Reynolds numbers (5000-10,000 based on displacement thickness), the maximum growth rate is found to increase with curvature - the maximum occurring at a nondimensional radius (based on displacement thickness) between 30 and 100.

Macaraeg, M. G.↗
NASA NTRS1973

Experimental investigation of boundary layers in an axisymmetric, Mach 2.5, mixed-compression inlet

An experimental investigation has been made of the boundary layer flow in a supersonic axisymmetric inlet. The inlet was designed for Mach 2.5 and had a 60 percent internal supersonic area contraction. Porous bleed regions were incorporated into both the cowl and centerbody for boundary-layer control. Five bleed configurations were studied; these included bleed regions upstream of, across, and downstream of the experimentally determined shock-impingement points. The tests were conducted at tunnel unit Reynolds numbers of 8.2 million and 2.7 million per meter. Static-pressure measurements were made along the internal inlet surfaces. In addition to locating the position of the shocks, these measurements also showed local regions of expansion resulting from the suction bleed. Boundary-layer profiles were measured with translating pitot pressure probes located on both sides of the shock-impingement points on the cowl and centerbody. These measurements showed that the boundary-layer profiles were distorted in the vicinity of the terminal shock.

Hingst, W. R.↗
NASA NTRS2019

A Comparison of Boundary Layer Wind Profilers for Use with Space Launch Vehicles

The United States Air Force (USAF) operates two space launch ranges, the Eastern Range (ER) and the Western Range (WR). The ER is primarily located at the Cape Canaveral Air Force Station (CCAFS) and the WR is located at the Vandenberg Air Force Base (VAFB). Multiple systems are used to measure the atmosphere at both ranges, including a suite of 915-Mhz (megahertz) Doppler Radar Wind Profilers (DRWP). The 915-MHz DRWPs are used to measure winds in the lowest few kilometers of the atmosphere, primarily in the boundary layer. Boundary layer winds are important during launch, and observations of such can be used as input to toxic dispersion and low-level abort trajectory models. However, these 915-MHz systems are nearing the end of their service life and need to be replaced by systems with similar, or greater, capabilities. The USAF funded evaluations of two systems: a 449-MHz DRWP and a Lidar. Both systems were stationed at each range for separate periods of approximately three months from November 2017 through May 2018. The USAF also funded NASA’s Marshall Space Flight Center (MSFC) Natural Environments Branch (NE) to evaluate wind output from the two systems. MSFC NE conducted analysis to demonstrate the system’s wind accuracy relative to measurements from the Automated Meteorological Profiling System (AMPS) (Divers et al., 2000), data availability, and Effective Vertical Resolution (EVR).

Orcutt, John M.↗
DOE OSTI2023

New scaling law for turbulent boundary layers with high surface mass transfer

A fundamental understanding of the phenomena occurring in the turbulent boundary layer in the presence of surface blowing is limited, and considerable disagreements persist even in describing primary quantities, such as the boundary layer profile. The theories based on the linear boundary layer equations show that the thickness of the sublayer increases in the presence of surface blowing; therefore, the viscous sublayer and law of the wall modify. In this study, direct numerical simulations (DNS) of turbulent boundary layers with uniform surface mass transfers are carried out in order to scale the velocity profile. Emphasis is placed on moderate to high mass transfer rates, which are relevant to the most common hybrid rockets configuration. DNS data are used to establish a functional law of the wall and a law of wake by means of the relation between the wall shear stress and surface mass transfer. Analysis of the mean kinetic energy budget shows that the magnitude of turbulent kinetic energy increases by surface mass transfer, and the production rate extends significantly in the inner layer as the injection rate increases. DNS data of various surface blowing are used to complete the closure of turbulence kinetic energy equation and develop an eddy viscosity model. The predicted turbulent kinetic energy and eddy viscosity agree with DNS data for moderate to high blowing rates.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1971

A numerical investigation into the effects of compressibility and total enthalpy difference on the development of a laminar free shear layer.

A method is presented for integrating numerically the equations of motion for a compressible free shear layer developing from a boundary-layer profile of arbitrary shape. Sutherland's law is used to determine the coefficient of viscosity and the Prandtl number is taken as 0.72. Calculated results are reported for free-stream Mach numbers ranging from 0 to 10 and for stagnation-enthalpy ratios ranging from 0 to 5.0. The effects of varying the initial boundary-layer profile and of a discontinuity in temperature at the origin are also studied. The results include graphs showing the development of dividing-streamline velocity, of local Nusselt number, and of dividing-streamline location.

Carpenter, P. W.↗
NASA NTRS1995

Experimental study of the use of vortex generators to reduce fluctuating pressure loads in shock wave turbulent boundary layer interactions

Fluctuating wall pressure measurements have been made in a separated shock wave/turbulent boundary layer interaction produced by an unswept compression corner in a Mach 5 flow. Wheeler doublet vortex generators were placed 15.8 boundary layer thicknesses upstream of the corner to study their effect on the fluctuating pressure loads produced by the translating separation shock. The vortex generators produced significant three-dimensionality in an otherwise two-dimensional interaction. They reduced the upstream influence and the length of the region of shock motion by 60% and 64%, respectively, decreased the maximum wall pressure rms by 23%, and shifted the fluctuations to a higher frequency band. The maximum fraction of energy in the 100-500 Hz frequency band is decreased by 11%. These changes are due to a fuller boundary layer profile, a weaker separation shock, and increased boundary layer turbulence causing increased separation shock jitter.

Barter, John W.↗