Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BOUNDARY LAYER SEPARATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Review of Research on Low-Profile Vortex Generators to Control Boundary-Layer Separation

An in-depth review of boundary-layer flow-separation control by a passive method using low-profile vortex generators is presented. The generators are defined as those with a device height between 10% and 50% of the boundary layer thickness. Key results are presented for several research efforts, all of which were performed within the past decade and a half where the majority of these works emphasize experimentation with some recent efforts on numerical simulations. Topics of discussion consist of both basic fluid dynamics and applied aerodynamics research. The fluid dynamics research includes comparative studies on separation control effectiveness as well as device-induced vortex characterization and correlation. The comparative studies cover the controlling of low-speed separated flows in adverse pressure gradient and supersonic shock-induced separation. The aerodynamics research includes several applications for aircraft performance enhancement and covers a wide range of speeds. Significant performance improvements are achieved through increased lift and/or reduced drag for various airfoils-low-Reynolds number, high-lift, and transonic-as well as highly swept wings. Performance enhancements for non-airfoil applications include aircraft interior noise reduction, inlet flow distortion alleviation inside compact ducts, and a more efficient overwing fairing. The low-profile vortex generators are best for being applied to applications where flow-separation locations are relatively fixed and the generators can be placed reasonably close upstream of the separation. Using the approach of minimal near-wall proturbances through substantially reduced device height, these devices can produce streamwise vortices just strong enough to overcome the separation without unnecessarily persisting within the boundary layer once the flow-control objective is achieved. Practical advantages of low-profile vortex generators, such as their inherent simplicity and low device drag, are demonstrated to be critically important for many applications as well.

Lin, John C.↗
NASA NTRS1977

Experiments on transonic and supersonic turbulent boundary-layer separation

Results of experimental investigations into turbulent boundary-layer behavior under the influence of pressure gradients and with separation are presented for transonic and supersonic flow fields. In the transonic case, an axisymmetric model was implemented consisting of an annular circular arc bump affixed to a circular cylinder aligned with the flow direction. For the supersonic separation study, an oblique shock wave impinging on the wind tunnel wall boundary layer was employed to cause separation. The mean streamwise and normal velocity components as well as the respective turbulence intensities were obtained with a two-color frequency shifted laser velocimeter.

Bachalo, W. D.↗
NASA NTRS1957

The Effects of Boundary-layer Separation over Bodies of Revolution with Conical Tail Flares

The magnitude and the effects of boundary-layer separation on normal-force-curve slopes, centers of pressure, pressure distributions, and lift and drag coefficients were determined for various bodies of revolution with conical tail flares at Mach numbers from 3.0 to 6.3. Some of the experimental results are compared to theoretical predictions of the aerodynamic characteristics of the bodies.

Dennis, David H↗
NASA NTRS1991

Streaming effect of wall oscillation to boundary layer separation

This paper presents a preliminary theoretical result on the time averaged streaming effect of local forcing excitation to the boundary layer separation from smooth surface. The problem is formulated as a periodic disturbance to a basic steady breakaway separating flow, for which the data are taken from a numerical triple-deck solution. The ratio of Strouhal number St and Reynolds number Re plays an important role, both being assumed sufficiently high. The analytical and numerical results show that this streaming effect is quite strong at proper values of St/Re exp 1/4, which may delay or even suppress the separation.

Wu, X. H.↗
NASA NTRS2003

Boundary-Layer Separation Control under Low-Pressure Turbine Airfoil Conditions using Glow-Discharge Plasma Actuators

Modem low-pressure turbines, in general, utilize highly loaded airfoils in an effort to improve efficiency and to lower the number of airfoils needed. Typically, the airfoil boundary layers are turbulent and fully attached at takeoff conditions, whereas a substantial fraction of the boundary layers on the airfoils may be transitional at cruise conditions due to the change of density with altitude. The strong adverse pressure gradients on the suction side of these airfoils can lead to boundary-layer separation at the latter low Reynolds number conditions. Large separation bubbles, particularly those which fail to reattach, cause a significant degradation of engine efficiency. A component efficiency drop of the order 2% may occur between takeoff and cruise conditions for large commercial transport engines and could be as large as 7% for smaller engines at higher altitude. An efficient means of of separation elimination/reduction is, therefore, crucial to improved turbine design. Because the large change in the Reynolds number from takeoff to cruise leads to a distinct change in the airfoil flow physics, a separation control strategy intended for cruise conditions will need to be carefully constructed so as to incur minimum impact/penalty at takeoff. A complicating factor, but also a potential advantage in the quest for an efficient strategy, is the intricate interplay between separation and transition for the situation at hand. Volino gives a comprehensive discussion of several recent studies on transition and separation under low-pressure-turbine conditions, among them one in the present facility. Transition may begin before or after separation, depending on the Reynolds number and other flow conditions. If the transition occurs early in the boundary layer then separation may be reduced or completely eliminated. Transition in the shear layer of a separation bubble can lead to rapid reattachment. This suggests using control mechanisms to trigger and enhance early transition. Gad-el-Hak provides a review of various techniques for flow control in general and Volino discusses recent studies on separation control under low-pressure-turbine conditions utilizing passive as well as active devices. As pointed out by Volino, passive devices optimized for separation control at low Reynolds numbers tend to increase losses at high Reynolds numbers, Active devices have the attractive feature that they can be utilized only in operational regimes where they are needed and when turned off would not affect the flow. The focus in the present paper is an experimental Separation is induced on a flat plate installed in a closed-circuit wind tunnel by a shaped insert on the opposite wall. The flow conditions represent flow over the suction surface of a modem low-pressure-turbine airfoil ('Pak-B'). The Reynolds number, based on wetted plate length and nominal exit velocity, is varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low (0.2%) and high (2.5%) Gee-stream turbulence intensities are set using passive grids. A spanwise-oriented phased-plasma-array actuator, fabricated on a printed circuit board, is surface- flush-mounted upstream of the separation point and can provide forcing in a wide frequency range. Static surface pressure measurements and hot-wire anemometry of the base and controlled flows are performed and indicate that the glow-discharge plasma actuator is an effective device for separation control. of active separation control using glow discharge plasma actuators.

Hultgren, Lennart S.↗
NASA NTRS2004

A Resonant Pulse Detonation Actuator for High-Speed Boundary Layer Separation Control

A variety of different types of actuators have been previously investigated as flow control devices. Potential applications include the control of boundary layer separation in external flows, as well as jet engine inlet and diffuser flow control. The operating principles for such devices are typically based on either mechanical deflection of control surfaces (which include MEMS flap devices), mass injection (which includes combustion driven jet actuators), or through the use of synthetic jets (diaphragm devices which produce a pulsating jet with no net mass flow). This paper introduces some of the initial flow visualization work related to the development of a relatively new type of combustion-driven jet actuator that has been proposed based on a pulse detonation principle. The device is designed to utilize localized detonation of a premixed fuel (Hydrogen)-air mixture to periodically inject a jet of gas transversely into the primary flow. Initial testing with airflow successfully demonstrated resonant conditions within the range of acoustic frequencies expected for the design. Schlieren visualization of the pulsating air jet structure revealed axially symmetric vortex flow, along with the formation of shocks. Flow visualization of the first successful sustained oscillation condition is also demonstrated for one configuration of the current test section. Future testing will explore in more detail the onset of resonant combustion and the approach to conditions of sustained resonant detonation.

Beck, B. T.↗
NASA NTRS1991

Turbulent boundary layer separation over a rearward facing ramp and its control through mechanical excitation

A vane oscillating about a fixed point at the inlet to a two-dimensional 20 degree rearward facing ramp has proven effective in delaying the separation of a turbulent boundary layer. Measurements of the ramp surface static pressure coefficient obtained under the condition of vane oscillation and constant inlet velocity revealed that two different effects occurred with surface distance along the ramp. In the vicinity of the oscillating vane, the pressure coefficients varied as a negative function of the vane's trailing edge rms velocity; the independent variable on which the rms velocity depends are the vane's oscillation frequency and its displacement amplitude. From a point downstream of the vane to the exit of the ramp; however, the pressure coefficient varied as a more complex function of the two independent variables. That is, it was found to vary as a function of the vane's oscillation frequency throughout the entire range of frequencies covered during the test, but over only a limited range of the trailing edge displacement amplitudes covered. More specifically, the value of the pressure coefficient was independent of increases in the vane's displacement amplitude above approximately 35 inner wall units of the boundary layer. Below this specific amplitude it varied as a function of the vane's trailing edge rms velocity. This height is close to the upper limit of the buffer layer. A parametric study was made to determine the variation of the maximum static pressure recovery as a function of the vane's oscillation frequency, for several ramp inlet velocities and a constant displacement amplitude of the vane's trailing edge. The results indicate that the phenomenon producing the optimum delay of separation may be Strouhal number dependent. Corona anemometer measurements obtained in the inner wall regions of the boundary layer for the excited case reveal a large range of unsteadiness in the local velocities. These measurements imply the existence of inflections in the profiles, which provide a mechanism for resulting inviscid flow instabilities to produce turbulence in the near wall region, thereby delaying separation of the boundary layer.

Mckinzie, Daniel J., Jr.↗
NASA NTRS1947

Drag Reduction by Suction of the Boundary Layer Separated Behind Shock Wave Formation at High Mach Numbers

With an approach of the velocity of flight of a ship to the velocity of sound, there occurs a considerable increase of the drag. The reason for this must be found in the boundary layer separation caused by formation of shock waves. It will be endeavored to reduce the drag increase by suction of the boundary layer. Experimental results showed that drag increase may be considerably reduced by this method. It was, also, observed that, by suction, the position of shock waves can be altered to a considerable extent.

Regenscheit, B.↗
NASA NTRS2005

Active control of Boundary Layer Separation & Flow Distortion in Adverse Pressure Gradient Flows via Supersonic Microjets

Inlets to aircraft propulsion systems must supply flow to the compressor with minimal pressure loss, flow distortion or unsteadiness. Flow separation in internal flows such as inlets and ducts in aircraft propulsion systems and external flows such as over aircraft wings, is undesirable as it reduces the overall system performance. The aim of this research has been to understand the nature of separation and more importantly, to explore techniques to actively control this flow separation. In particular, the use of supersonic microjets as a means of controlling boundary layer separation was explored. The geometry used for the early part of this study was a simple diverging Stratford ramp, equipped with arrays of supersonic microjets. Initial results, based on the mean surface pressure distribution, surface flow visualization and Planar Laser Scattering (PLS) indicated a reverse flow region. We implemented supersonic microjets to control this separation and flow visualization results appeared to suggest that microjets have a favorable effect, at least to a certain extent. However, the details of the separated flow field were difficult to determine based on surface pressure distribution, surface flow patterns and PLS alone. It was also difficult to clearly determine the exact influence of the supersonic microjets on this flow. In the latter part of this study, the properties of this flow-field and the effect of supersonic microjets on its behavior were investigated in further detail using 2-component (planar) Particle Image Velocimetry (PIV). The results clearly show that the activation of microjets eliminated flow separation and resulted in a significant increase in the momentum of the fluid near the ramp surface. Also notable is the fact that the gain in momentum due to the elimination of flow separation is at least an order of magnitude larger (two orders of magnitude larger in most cases) than the momentum injected by the microjets and is accomplished with very little mass flow through the microjets.

Alvi, Farrukh S.↗
NASA NTRS1974

Use of multiple discrete wall jets for delaying boundary layer separation

The effectiveness of a spanwise array of small discrete blowing nozzles in preventing separation of a turbulent boundary layer was investigated experimentally. The spacing, axial location, and momentum flux of the nozzles were varied in a systematic way, and overall performance was measured for each combination. Extensive mean velocity profiles were measured for one selected combination. Overall diffusion achieved before separation was correlated successfully with a momentum flux excess parameter, and in terms of this parameter discrete nozzles, when advantageously placed, were found to perform somewhat better than an optimally placed two-dimensional jet slot.

Mclean, J. D.↗
NASA NTRS1974

Differential analysis for the turbulent boundary layer on a compressor blade element (including boundary-layer separation)

A two-dimensional differential analysis is developed to approximate the turbulent boundary layer on a compressor blade element with strong adverse pressure gradients, including the separated region with reverse flow. The predicted turbulent boundary layer thicknesses and velocity profiles are in good agreement with experimental data for a cascade blade, even in the separated region.

Schmidt, J. F.↗
NASA NTRS1978

Boundary-layer separation on isolated boattail nozzles

An angle of attack of 0 deg was investigated in the Langley 16 foot transonic tunnel at free-stream Mach numbers from 0.40 to 0.95 to study the phenomenon of separated flow on a series of circular-arc afterbodies. Both high-pressure air and solid circular cylinders with the cylinder diameter equal to the nozzle-exit diameter were used to simulate jet exhausts. The results indicate that boundary-layer separation is most extensive on steep boattails at high Mach numbers. The jet total-pressure ratio changes (jet total pressure to free-stream static pressure) affected the extent of separation very little; however, comparison of the separation data obtained by using the two jet-simulation techniques indicate that entrainment associated with the presence of a jet had a significant effect on the extent of separation. The solid-simulator separation data were also used to evaluate the predictions of eight separation criteria.

Abeyounis, W. K.↗
NASA NTRS1990

On the Lagrangian description of unsteady boundary-layer separation. I - General theory

Although unsteady, high-Reynolds number, laminar boundary layers have conventionally been studied in terms of Eulerian coordinates, a Lagrangian approach may have significant analytical and computational advantages. In Lagrangian coordinates the classical boundary layer equations decouple into a momentum equation for the motion parallel to the boundary, and a hyperbolic continuity equation (essentially a conserved Jacobian) for the motion normal to the boundary. The momentum equations, plus the energy equation if the flow is compressible, can be solved independently of the continuity equation. Unsteady separation occurs when the continuity equation becomes singular as a result of touching characteristics, the condition for which can be expressed in terms of the solution of the momentum equations. The solutions to the momentum and energy equations remain regular. Asymptotic structures for a number of unsteady 3-D separating flows follow and depend on the symmetry properties of the flow. In the absence of any symmetry, the singularity structure just prior to separation is found to be quasi 2-D with a displacement thickness in the form of a crescent shaped ridge. Physically the singularities can be understood in terms of the behavior of a fluid element inside the boundary layer which contracts in a direction parallel to the boundary and expands normal to it, thus forcing the fluid above it to be ejected from the boundary layer.

Van Dommelen, Leon L.↗
NASA NTRS1977

Investigation of supersonic turbulent boundary-layer separation on a compression ramp by an integral method

An investigation was made to determine the feasibility of using a boundary layer integral method to study the separation of a turbulent boundary layer on a two dimensional ramp at supersonic speeds. The numerical calculations were made for a free stream Mach number of 3, a Reynolds number of 10 million, and over a ramp angle range from 0 deg to 30 deg. For ramp angles where no flow separation was indicated, theoretical calculations were in reasonable agreement with experimental data except for a somewhat belated rise in pressure. For larger ramp angles, where separation was present, the investigation produced results that were not in agreement with experiment or with results calculated by time dependent Navier-Stokes methods. This apparently was true because no provision had been made for a proper shock boundary layer interaction where strong normal pressure gradients are induced within the boundary layer under the shock independent of surface curvature effects.

Patel, D. K.↗
NASA NTRS1991

Turbulent boundary layer separation over a rearward facing ramp and its control through mechanical excitation

A vane which oscillates about a fixed point at the inlet to a two-dimensional, 20-deg rearward-facing ramp has been noted to effectively delay the separation of a turbulent boundary layer. A parametric study has been conducted to determine the variation of the maximum values of the static pressure recovery, measured close to the ramp exit as a function of the oscillation frequency of the vane. The resulting curves show a peak value in the maximum static pressure recovery as a function of the vane's oscillation frequency. For the excited cases, corona anemometer measurements in the inner wall regions of the boundary layer along the surface of the ramp show a large range of unsteadiness in the local velocities. Finally, a qualitative explanation of the phenomena of delay of separation is discussed which appears to be supported by the surface static pressure and flow field measurements obtained.

Mckinzie, Daniel J., Jr.↗