SEARCH · Engineering Papers

Results for “BOUNDARY LAYER CHARACTERISTICS - WING SECTIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS2012

Boundary Layer Flow Control by an Array of Ramp-Shaped Vortex Generators

Flow field survey results for the effect of ramp-shaped vortex generators (VG) on a turbulent boundary layer are presented. The experiments are carried out in a low-speed wind tunnel and the data are acquired primarily by hot-wire anemometry. Distributions of mean velocity and turbulent stresses as well as streamwise vorticity, on cross-sectional planes at various downstream locations, are obtained. These detailed flow field properties, including the boundary layer characteristics, are documented with the primary objective of aiding possible computational investigations. The results show that VG orientation with apex upstream, that produces a downwash directly behind it, yields a stronger pair of streamwise vortices. This is in contrast to the case with apex downstream that produces a pair of vortices of opposite sense. Thus, an array of VG s with the former orientation, usually considered for film-cooling application, may also be superior for mixing enhancement and boundary layer separation control. (See CASI ID 20120009374 for Supplemental CD-ROM.)

Zaman, K. B. M. Q.↗

NASA NTRS2012

Boundary Layer Flow Control by an Array of Ramp-Shaped Vortex Generators

Zaman, K. B. M. Q.↗

NASA NTRS1984

Natural laminar flow airfoil design considerations for winglets on low-speed airplanes

Winglet airfoil section characteristics which significantly influence cruise performance and handling qualities of an airplane are discussed. A good winglet design requires an airfoil section with a low cruise drag coefficient, a high maximum lift coefficient, and a gradual and steady movement of the boundary layer transition location with angle of attack. The first design requirement provides a low crossover lift coefficient of airplane drag polars with winglets off and on. The other requirements prevent nonlinear changes in airplane lateral/directional stability and control characteristics. These requirements are considered in the design of a natural laminar flow airfoil section for winglet applications and chord Reynolds number of 1 to 4 million.

Vandam, C. P.↗

NASA NTRS1971

Computer program for design of two-dimensional supersonic turbine rotor blades with boundary-layer correction

A FORTRAN 4 computer program for the design of two-dimensional supersonic rotor blade sections corrected for boundary-layer displacement thickness is presented. The ideal rotor is designed by the method of characteristics to produce vortex flow within the blade passage. The boundary-layer parameters are calculated by Cohen and Reshotoko's method for laminar flow and Sasman and Cresci's method for turbulent flow. The program input consists essentially of the blade surface Mach number distribution and total flow conditions. The primary output is the corrected blade profile and the boundary-layer parameters.

Goldman, L. J.↗

NASA NTRS1997

Flow Quality and Boundary Layer Transition

The widely held view is that transition to turbulence in the Blasius boundary layer occurs via amplification and eventual nonlinear breakdown of initially small amplitude instabilities i.e. Tollmien-Schlichting (TS) waves. However this scenario is only observed for low amplitude free-stream turbulence levels, i.e. u/U < 0.1%. Bypass of linear TS instability mechanism occurs for higher EST levels, yet considerable differences exist between the few experiments carefully designed to assess the effect of EST on transition. The consensus is that EST leads to longitudinal streaks that form near the leading edge in the boundary layer . These streaks appeal to be regions of concentrated streamwise vorticity and they are often referred to as Klebanoff modes. The importance of mean flow free-stream nonuniformity (FSN) is not as widely appreciated as EST for characterizing wind tunnel flow quality. Here it is shown that, although the v like generated by a d=50micron wire located upstream of the contraction (Re(sub d)=6.6, x/d=45,000) is immeasurably small by the time it interacts with the leading edge in the test section, it is responsible for generation of a pair of weak streamwise vortices in the boundary layer downstream. The characteristics of these wake-induced vortices and their effect on TS waves are demonstrated. Small remnant FSN variations are also shown to exist downstream of a turbulence grid. The question arises Are the adverse effects introduced by the turbulence grid caused by FST or by small remnant FSN variations?

Watmuff, Jonathan H↗

NASA NTRS1983

Transient response of a turbulent boundary layer

A unique feature of the present ensemble-averaged measurements of a turbulent boundary layer's transient response to a spontaneous change in the free stream velocity distribution, is that the test boundary layer is a standard, steady, flat plate turbulent boundary layer at the entrance to the unsteady region, and is then subjected to sudden changes in free stream velocity distribution in the test section. These water tunnel tests were controlled by minicomputer. It is noted that the boundary layer development was relatively slow, with a characteristic time that was greater than the free stream time-of-flight by a factor of as much as 3. Response varied dramatically across the boundary layer, and the evolution of the turbulent stress field occurred on the same time scale as that of the ensemble-averaged velocity field.

Parikh, P. G.↗

NASA NTRS1988

Wind tunnel-sidewall-boundary-layer effects in transonic airfoil testing-some correctable, but some not

The need to correct transonic airfoil wind tunnel test data for the influence of the tunnel sidewall boundary layers, in addition to the wall accepted corrections for the analytical investigation was carried out in order to evaluate sidewall boundary layer effects on transonic airfoil characteristics, and to validate proposed correction and the limit to their applications. This investigation involved testing of modern airfoil configurations in two different transonic airfoil test facilities, the 15 x 60 inch two-dimensional insert of the National Aeronautical Establishment (NAE) 5 foot tunnel in Ottawa, Canada, and the two-dimensional test section of the NASA Langley 0.3 m Transonic Cryogenic Tunnel (TCT). Results presented included effects of variations in sidewall-boundary layer bleed in both facilities, different sidewall boundary layer correction procedures, tunnel-to tunnel comparisons of correcte results, and flow conditions with and without separation.

Lynch, F. T.↗

NASA NTRS1987

The design and preliminary calibration of a boundary-layer flow channel

Design procedures for a new low-speed boundary-layer research channel are described. The channel is an open-circuit wind tunnel for the study of two-dimensional boundary layers under controlled pressure gradients, and follows design guidelines from published literature on blower tunnels with wide-angle diffusers. The contraction was arranged in a modular fashion permitting two different test sections of square and high-aspect-ratio cross section. A radical type of wide-angle diffuser was employed, and a stream-tube computer code (GE Streamtube Curvature Code) was used to check the contraction designs. The alternate test sections have the following specifications: 2- by 2-foot cross section with a fixed velocity of 23 ft/sec, and a boundary-layer section with a 0.5- by 2-foot cross section at a fixed velocity of approximately 89 ft/sec. Experimental techniques and data are described for the evaluation of diffuser effectiveness, boundary-layer channel characteristics, and overall performance of the facility.

Rao, Dhanvada M.↗

NASA NTRS1983

Improved design of subcritical and supercritical cascades using complex characteristics and boundary layer correction

The method of complex characteristics and hodograph transformation for the design of shockless airfoils was extended to design supercritical cascades with high solidities and large inlet angles. This capability was achieved by introducing a conformal mapping of the hodograph domain onto an ellipse and expanding the solution in terms of Tchebycheff polynomials. A computer code was developd based on this idea. A number of airfoils designed with the code are presented. Various supercritical and subcritical compressor, turbine and propeller sections are shown. The lag-entrainment method for the calculation of a turbulent boundary layer was incorporated to the inviscid design code. The results of this calculation are shown for the airfoils described. The elliptic conformal transformation developed to map the hodograph domain onto an ellipse can be used to generate a conformal grid in the physical domain of a cascade of airfoils with open trailing edges with a single transformation. A grid generated with this transformation is shown for the Korn airfoil.

Sanz, J. M.↗

NASA NTRS1984

Improved design of subcritical and supercritical cascades using complex characteristics and boundary-layer correction

The method of complex characteristics and hodograph transformation for the design of shockless airfoils was extended to design supercritical cascades with high solidities and large inlet angles. This capability was achieved by introducing a conformal mapping of the hodograph domain onto an ellipse and expanding the solution in terms of Tchebycheff polynomials. A computer code was developed based on this idea. A number of airfoils designed with the code are presented. Various supercritical and subcritical compressor, turbine and propeller sections are shown. The lag-entrainment method for the calculation of a turbulent boundary layer was incorporated to the inviscid design code. The results of this calculation are shown for the airfoils described. The elliptic conformal transformation developed to map the hodograph domain onto an ellipse can be used to generate a conformal grid in the physical domain of a cascade of airfoils with open trailing edges with a single transformation. A grid generated with this transformation is shown for the Korn airfoil. Previously announced in STAR as N83-24474

Sanz, J. M.↗

NASA NTRS1953

Performance Characteristics of Plane-Wall Two-Dimensional Diffusers

Experiments have been made at Stanford University to determine the performance characteristics of plane-wall, two-dimensional diffusers which were so proportioned as to insure reasonable approximation of two-dimensional flow. All of the diffusers had identical entrance cross sections and discharged directly into a large plenum chamber; the test program included wide variations of divergence angle and length. During all tests a dynamic pressure of 60 pounds per square foOt was maintained at the diffuser entrance and the boundary layer there was thin and fully turbulent. The most interesting flow characteristics observed were the occasional appearance of steady, unseparated, asymmetric flow - which was correlated with the boundary-layer coalescence - and the rapid deterioration of flow steadiness - which occurred as soon as the divergence angle for maximum static pressure recovery was exceeded. Pressure efficiency was found to be controlled almost exclusively by divergence angle, whereas static pressure recovery was markedly influenced by area ratio (or length) as well as divergence angle. Volumetric efficiency. diminished as area ratio increased, and at a greater rate with small lengths than with large ones. Large values of the static-pressure-recovery coefficient were attained only with long diffusers of large area ratio; under these conditions pressure efficiency was high and. volumetric efficiency low. Auxiliary tests with asymmetric diffusers demonstrated that longitudinal pressure gradient, rather than wall divergence angle, controlled flow separation. Others showed that the addition of even a short exit duct of uniform section augmented pressure recovery. Finally, it was found that the installation of a thin, central, longitudinal partition suppressed flow separation in short diffusers and thereby improved pressure recovery

Reid, Elliott G↗

NASA NTRS1984

Evaluation of the Langley 4- by 7-meter tunnel for propeller noise measurements

An experimental and theoretical evaluation of the Langley 4- by 7- Meter Tunnel was conducted to determine its suitability for obtaining propeller noise data. The tunnel circuit and open test section are described. An experimental evaluation is performed using microphones placed in and on the tunnel floor. The reflection characteristics and background noise are determined. The predicted source (propeller) near-field/far-field boundary is given using a first-principles method. The effect of the tunnel-floor boundry layer on the noise from the propeller is also predicted. A propeller test stand used for part of his evaluation is also described. The measured propeller performance characteristics are compared with those obtained at a larger scale, and the effect of the test-section configuration on the propeller performance is examined. Finally, propeller noise measurements were obtained on an eight-bladed SR-2 propeller operating at angles of attack -8 deg, 0 deg, and 4.6 deg to give an indication of attainable signal-to-noise ratios.

Block, P. J. W.↗

NASA NTRS1975

Theoretical and experimental study of a new method for prediction of profile drag of airfoil sections

Theoretical and experimental studies are described which were conducted for the purpose of developing a new generalized method for the prediction of profile drag of single component airfoil sections with sharp trailing edges. This method aims at solution for the flow in the wake from the airfoil trailing edge to the large distance in the downstream direction; the profile drag of the given airfoil section can then easily be obtained from the momentum balance once the shape of velocity profile at a large distance from the airfoil trailing edge has been computed. Computer program subroutines have been developed for the computation of the profile drag and flow in the airfoil wake on CDC6600 computer. The required inputs to the computer program consist of free stream conditions and the characteristics of the boundary layers at the airfoil trailing edge or at the point of incipient separation in the neighborhood of airfoil trailing edge. The method described is quite generalized and hence can be extended to the solution of the profile drag for multi-component airfoil sections.

Goradia, S. H.↗

NASA NTRS1994

Ionospheric footprint of magnetosheathlike particle precipitation observed by an incoherent scatter radar

We have examined Sondrestrom incoherent scatter radar observations of ionospheric plasma density and temperature distributions and measurements of F region ion drifts that were made during a prenoon pass of the Defense Meteorological Satellite Program (DMSP)-F7 satellite through the radar field of view. The spacecraft traversed a region of intense electron precipitation with a characteristic energy below approximately 200 eV. Particles with such low characteristic energies are believed to be directly or indirectly of magnetosheath origin. The precipitation region had a width about 2 deg invariant latitude and covered the low-latitude boundary layer (LLBL), the cusp, and the equatorward section of the plasma mantle (PM). The corotating radar observed a patch of enhanced electron density and elevated electron temperature in the F2 region between about 10.5 and 12 magnetic local time in the same invariant latitude range where DMSP-F7 detected the soft-electron flux. The ion drift pattern, also obtained by radar, shows that it is unlikely that the plasma patch was produced by solar radiation and advected into the radar field of view. We suggest that the radar observed modifications of the ionospheric plasma distribution, which resulted from direct entry of magnetosheath electrons into the magnetosphere and down to ionospheric altitudes. Model calculations of the ionospheric response to the observed electron precipitation support our interpretation. The spectral characteristics of the electron flux in the LLBL, cusp, and equatorward section of the PM were in this case too similar to allow to distinguish between them by using incoherent scatter radar measurements only.

Watermann, Jurgen↗

NASA NTRS1987

Design and test of a natural laminar flow/large Reynolds number airfoil with a high design cruise lift coefficient

Research activity on an airfoil designed for a large airplane capable of very long endurance times at a low Mach number of 0.22 is examined. Airplane mission objectives and design optimization resulted in requirements for a very high design lift coefficient and a large amount of laminar flow at high Reynolds number to increase the lift/drag ratio and reduce the loiter lift coefficient. Natural laminar flow was selected instead of distributed mechanical suction for the measurement technique. A design lift coefficient of 1.5 was identified as the highest which could be achieved with a large extent of laminar flow. A single element airfoil was designed using an inverse boundary layer solution and inverse airfoil design computer codes to create an airfoil section that would achieve performance goals. The design process and results, including airfoil shape, pressure distributions, and aerodynamic characteristics are presented. A two dimensional wind tunnel model was constructed and tested in a NASA Low Turbulence Pressure Tunnel which enabled testing at full scale design Reynolds number. A comparison is made between theoretical and measured results to establish accuracy and quality of the airfoil design technique.

Kolesar, C. E.↗

NASA NTRS2001

Abe Silverstein 10- by 10-Foot Supersonic Wind Tunnel Validated for Low-Speed (Subsonic) Operation

The NASA Glenn Research Center and Lockheed Martin Corporation tested an aircraft model in two wind tunnels to compare low-speed (subsonic) flow characteristics. Objectives of the test were to determine and document the similarities and uniqueness of the tunnels and to validate that Glenn's 10- by 10-Foot Supersonic Wind Tunnel (10x10 SWT) is a viable low-speed test facility. Results from two of Glenn's wind tunnels compare very favorably and show that the 10x10 SWT is a viable low-speed wind tunnel. The Subsonic Comparison Test was a joint effort by NASA and Lockheed Martin using the Lockheed Martin's Joint Strike Fighter Concept Demonstration Aircraft model. Although Glenn's 10310 and 836 SWT's have many similarities, they also have unique characteristics. Therefore, test data were collected for multiple model configurations at various vertical locations in the test section, starting at the test section centerline and extending into the ceiling and floor boundary layers.

Hoffman, Thomas R.↗

NASA NTRS1993

Aerodynamic characteristics and pressure distributions for an executive-jet baseline airfoil section

A wind tunnel test of an executive-jet baseline airfoil model was conducted in the adaptive-wall test section of the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel. The primary goal of the test was to measure airfoil aerodynamic characteristics over a wide range of flow conditions that encompass two design points. The two design Mach numbers were 0.654 and 0.735 with corresponding Reynolds numbers of 4.5 x 10(exp 6) and 8.9 x 10(exp 6) based on chord, respectively, and normal-force coefficients of 0.98 and 0.51, respectively. The tests were conducted over a Mach number range from 0.250 to 0.780 and a chord Reynolds number range from 3 x 10(exp 6) to 18 x 10(exp 6). The angle of attack was varied from -2 deg to a maximum below 10 deg with one exception in which the maximum was 14 deg for a Mach number of 0.250 at a chord Reynolds number of 4.5 x 10(exp 6). Boundary-layer transition was fixed at 5 percent of chord on both the upper and lower surfaces of the model for most of the test. The adaptive-wall test section had flexible top and bottom walls and rigid sidewalls. Wall interference was minimized by the movement of the adaptive walls, and the airfoil aerodynamic characteristics were corrected for any residual top and bottom wall interference.

Allison, Dennis O.↗

NASA NTRS2013

Hot-Film and Hot-Wire Anemometry for a Boundary Layer Active Flow Control Test

Unsteady active flow control (AFC) has been used experimentally for many years to minimize bluff-body drag. This technology could significantly improve performance of rotorcraft by cleaning up flow separation. It is important, then, that new actuator technologies be studied for application to future vehicles. A boundary layer wind tunnel was constructed with a 1ft-x-3ft test section and unsteady measurement instrumentation to study how AFC manipulates the boundary layer to overcome adverse pressure gradients and flow separation. This unsteady flow control research requires unsteady measurement methods. In order to measure the boundary layer characteristics, both hot-wire and hot-film Constant Temperature Anemometry is used. A hot-wire probe is mounted in the flow to measure velocity while a hot-film array lays on the test surface to measure skin friction. Hot-film sensors are connected to an anemometer, a Wheatstone bridge circuit with an output that corresponds to the dynamic flow response. From this output, the time varying flow field, turbulence, and flow reversal can be characterized. Tuning the anemometers requires a fan test on the hot-film sensors to adjust each output. This is a delicate process as several variables drastically affect the data, including control resistance, signal input, trim, and gain settings.

Control Test↗