SEARCH · Engineering Papers

Results for “BINARY EUTECTIC ALLOYS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Directionally solidified pseudo-binary eutectics of Ni-Cr-/Hf,Zr/

This report is concerned with the experimental determination of pseudo binary eutectic compositions and the directional solidification of the Ni-Cr-Hf,Zr, and Ni-Cr-Zr eutectic alloys. To determine unknown eutectics, chemical analyses were made of material bled from near eutectic ingots during incipient melting. Nominal compositions in weight per cent of Ni-18.6Cr-24.0Hf, Ni-19.6Cr-12.8Zr-2.8Hf, and Ni-19.2Cr-14.8Zr formed aligned pseudo-binary eutectic structures. The melting points were about 1270 C. The reinforcing intermetallic phases were identified as noncubic (Ni,Cr)7Hf2 and (Ni,Cr)7(Hf,Zr)2, and face centered cubic (Ni,Cr)5Zr. The volume fraction of the reinforcing phases were about 0.5.

Kim, Y. G.↗

NASA NTRS1988

Fraction eutectic measurements in slowly cooled Pb - 15 wt percent Sn alloys

A space shuttle experiment employing the General Purpose Furnace in its isothermal mode of operation is currently manifested for flight circa 1989. The aim of this experiment was to investigate the role of gravity in a slowly, and isothermally, cooled sample of a binary Pb - 15 wt percent Sn alloy. Ground based work in support of the microgravity experiment is discussed. In particular, it is shown that fraction eutectic measurements using an image analyzer, can be used to satisfactorily describe macrosegregation occurring in these slowly cooled ingots.

Studer, Anthony C.↗

NASA NTRS1973

Some possible filler alloys with low vapor pressures for refractory-metal brazing

A compilation of eutectics and melting-point minima for binary combinations of metals having vapor pressures below 10 to the minus 10th power torr at 1500 degrees K and .00005 torr at 2000 degree K is presented. These compositions and others near them on their phase diagrams are potential special brazing fillers for refractory metals. Some possible problems and advantages for fusion bonds of such mixtures are indicated. Evaluations of brazing fillers containing refractory metals are reported.

Morris, J. F.↗

NASA NTRS1978

Some properties of low-vapor-pressure braze alloys for thermionic converters

Density, dc electrical resistivity, thermal conductivity, and linear thermal expansion are measured for arc-melted rod-shaped samples of binary eutectics of Zr, Hf, Ru, Nb, Ir, Mo, Ta, Os, Re, and W selected as very-low-pressure braze fillers for thermionic converters. The first two properties are measured at 296 K for Zr-21.7 at% Ru, Zr-13 wt% W, Zr-19 wt% W, Zr-22.3 at% Nb, Nb-66.9 at% Ru, Hf-25.3 wt% Re, Zr-25.7 at% Ta, Hf-22.5 at% W, and Nb-35 wt% Mo. The last property is measured from 293 K to 2/3 melting point for specified alloys of different compositions. Resistivities of 0.000055 to 0.000181 ohm-cm are observed with the alloys having resistivities about ten times that of the less resistive constituent metal and about three times that of the more resistive constituent metal, except for Zr-19 wt% W and Nb-35 wt% Mo (greater resistivities). Thermal expansion coefficients vary from 0.000006 to 0.0000105/K. All brazes exhibit linear thermal expansion near that of their constituent metals.

Bair, V. L.↗

NASA NTRS1951

Relations between the modulus of elasticity of binary alloys and their structure

A comprehensive survey of the elastic modulus of binary alloys as a function of the concentration is presented. Alloys that form continuous solid solutions, limited solid solutions, eutectic alloys, and alloys with intermetallic phases are investigated. Systems having the most important structures have been examined to obtain criteria for the relation between lattice structure, type of binding, and elastic behavior.

METALS - STRUCTURES↗

DOE OSTI2025

Leveraging Artificial Intelligence to Predict Novel Eutectic Alloys

The goal of this project was to train an artificial neural network (ANN) to predict the fractional composition and melting point of eutectic alloys using fundamental atomic properties as inputs. The fundamental properties considered include atomic number, atomic weight, atomic radius, valence electron concentration, electronegativity, and electron affinity. The project involved several phases, starting with data preparation, where phase diagram data was harvested from the ASM International database. Approximately 1300 binary eutectics were collected and cleaned to ensure relevance and accuracy. A regression model was selected for training, utilizing a rectified linear unit as the activation function. Various model configurations were evaluated for predictive accuracy, with validation techniques employed to ensure robustness. The model demonstrated predictive capabilities above random guessing and was able to achieve up to 11% accuracy under certain conditions. An ablative test identified atomic radius and valence electron concentration as critical inputs for model performance. Incorporating the melting point of atomic constituents improved accuracy significantly, although ultimately the model’s predictive capability still fell short of the 80% target. This report details the methodology, results, and implications of the research, contributing to the understanding of employing artificial intelligence to predict the phase transition behavior of eutectic alloys.

36 MATERIALS SCIENCE↗

NASA NTRS1988

Microsegregation in directionally solidified Pb-8.4 at. pct Au alloy

The dependence of microsegregation behavior on growth rate and thermal gradient has been examined in a Pb-8.4 at. pct Au alloy material partially directionally solidified and quenched. The composition of the quenched 'liquid' at the dendrite tip (Ct), that of the eutectic-like solid phase freezing from the interdendritic liquid at the base of dendrite (Cse), the volume fraction of this eutectic-like region (fe), and solute profiles in the interdendritic quenched liquid and ahead of the dendrite have been measured. Two dendritic growth models for solidification of a binary alloy melt in a positive thermal gradient at the liquid-solid interface, one for dendrites with 'minimum undercooled dendrite tip' and the other for an Ivantsov type of dendrite with 'marginally stable tip', have been examined for a quantitative comparison with measured values of Ct, Cse, and fe. Convection in the melt, possibly due to horizontal density gradients, is found to be a serious limitation for theoretical understanding of the observed experimental behavior and meaningful comparison of theories.

Tewari, S. N.↗

NASA NTRS1992

Microstructural development during directional solidification of peritectic alloys

Despite the widespread commercial use of peritectic alloys (e.g., steels, brass, bronze, intermetallic compounds, Co based superalloys and A3B type superconductors), the characterization of the microstructural development during directional solidification of peritectics has historically lagged behind similar efforts directed towards other types of binary invariant reactions such as eutectic or monotectic. A wide variety of possible microstructures has been shown to form in peritectics depending upon the imposed temperature gradient, G, the solidification velocity, V, as well as the presence or absence of convection in the melt. This has important technological implications since many commercially important alloys exhibit peritectics and processing methods such as casting and welding often involve widely changing conditions. It has been the aim of this project to examine, in a systematic fashion, both experimentally and theoretically, the influence of gravitationally driven convection on segregation and microstructural development during solidification in peritectic systems under terrestrial conditions. The scientific results of the project will be used to establish ground based data in support of a meaningful microgravity flight experiment.

Lograsso, Thomas A.↗

DOE OSTI2024

Effect of Si impurities on microstructure and tensile properties of a cast Al-Mg-Fe alloy

Al-Mg alloys are attractive for structural castings owing to their superior strength and ductility in the as-cast state. However, given the tight tolerance for impurities, Al-Mg alloys produced from secondary sources still face multiple challenges. Here, we report the effect of increased Si impurity (0.05–1.6 wt%), which is commonly found in secondary Al sources, on microstructure and tensile properties of a cast Al-4.3Mg-1.6Fe (wt%) alloy, commercially referred to as Castaduct-42 alloy. Microstructural characterization revealed that Si addition increased the volume fraction, size, and aspect ratio of primary Al13Fe4 intermetallic particles as well as the volume fraction of other binary and ternary eutectic phases. Tensile testing results demonstrated that increasing Si impurities from 0.05 to 1.6 wt% reduced ductility from 14.3 ± 1.4 % to 2.2 ± 1.0 %. A particle cracking damage accumulation model coupled with failure analysis indicated primary Al13Fe4 intermetallic particles to be the major contributing factor to the deterioration in ductility with increasing Si content. Additionally, the stabilizing effect of Si on primary Al 13 Fe 4 was inconsistent with the CALPHAD calculation results based on existing CALPHAD databases which predict a slightly decreasing primary Al13Fe4 phase fraction with increasing Si concentration. This work provides new insights into the phase stability and mechanical behavior of the lesser studied Al-Mg-Fe-Si alloy system that will contribute to the development of sustainable cast Al-Mg based alloys.

36 MATERIALS SCIENCE↗

NASA NTRS1984

A redetermination of the succinonitrile-water phase diagram

The phase diagram of the water/succinonitrile system often used in modeling binary metallic alloys is determined experimentally using a laser scattering method. Triply distilled and zone-refined succinonitrile is placed in a jacketed water-cooled vessel with a magnetic mixer and a copper-constantan thermocouple, and the melting point is determined under vacuum and under Ar by observing the response of a photodiode placed opposite a laser source as the chamber is cooled and reheated. Then water is added, and the eutectic and monotectic temperatures and the entire phase diagram are determined under Ar. The results are presented in a table and graph and compared to those of Schreinemakers (1897): significant discrepancies are noted and attributed to impurities in the succinonitrile used by Schreinemakers. The importance of accurate phase diagrams for modeling binary alloys is stressed.

Smith, J. E., Jr.↗

DOE OSTI2025

Phase equilibria and microstructure evolution in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C

The equilibrium compositions of all phases in the Ni-rich region of binary Ni-Ce and ternary Ni-Ce-X (X=Al, Nb, Cr, Ti) systems at 900 °C were determined experimentally through isothermal annealing for up to 500 h and compared with currently available computational thermodynamic descriptions. Additionally, the study examined how adding a third element to the binary system affects the microstructure by analyzing changes in the volume fraction of the intermetallic phase in the eutectic region. It was observed that Nb and Ti addition lowered the intermetallic fraction in the eutectic region while Al and Cr addition did the opposite. The fraction of intermetallic phase in the eutectic region is very important because it contributes to extreme brittleness of these alloys. Also, Al, Nb and Ti addition promoted different precipitates upon annealing when added in sufficient amounts. The collected data on composition and phase equilibria provides crucial information for improving the thermodynamic assessments of the binary and ternary alloy systems.

energy dispersive spectrometry↗

NASA NTRS1976

Low vapor pressure braze alloys for thermionic energy converters

The evaluation of cesium diode electrode materials called for braze fillers with very low vapor pressures and a wide range of melting points. Binary alloys of low vapor pressure refractory metals were chosen to fill this need. These alloys of Th, Zr, Hf, Ru, Nb, Ir, Mo, Ta, Os, Re, and W have reported melting point minima or eutectics from 1,510 K to above 3,000 K. Preliminary data are compiled on the use of several of these braze alloys. Melting points and surface wetting on a Ta base are given. Results of brazing Ir, LaB6, Nb, Re, W, and Zr-22 wt % ZrO2 materials into Ta and Nb-1% Zr bases are presented. Current braze usage is summarized.

Bair, V. L.↗

NASA NTRS1976

Low vapor pressure braze alloys for thermionic energy converters

Preliminary results in the use of some low-vapor-pressure braze alloys are reported; these are binary alloys of refractory metals (Th, Zr, Hf, Ru, Nb, Ir, Mo, Ta, Os, Re, W) with vapor pressures below 0.1 nanotorr at 1500 K or 10 microtorr at 2000 K. The melting point minima or eutectics of the alloys range from 1510 K to above 3000 K. Melting points and surface wetting on a Ta base are given. Results are presented on brazing of Ir, LaB6, Nb, Re, W, and ZrO2 (with 22 wt % Zr) into a Ta base or a Nb-1% Zr base. The results are applicable in electrode screening programs for thermionic cesium diodes.

Bair, V. L.↗

NASA NTRS1989

Finite element simulations of thermosolutal convection in vertical solidification of binary alloys

Dendritic vertical solidification of a binary alloy is modeled using the finite element method to assess the effect of thermosolutal convection in macrosegregation. The mathematical model assumes steady-state solidification with a planar, undeformable surface defined by the dendrite tips and the eutectic isotherm. The dendritic region is assumed to advance at a constant solidification velocity v. The stability of the modeled system has been investigated and nonlinear calculations performed that show finger-like convection when the system is unstable. Results for lead-tin alloys show that when the system is unstable, convection is only significant in the uppermost part of the mush and is entirely driven by convection in the bulk fluid.

Heinrich, J. C.↗

NASA NTRS1989

Rapid solidification of high-conductivity copper alloys

The main objective was to develop improved copper alloys of high strength and high thermal and electric conductivity. Chill block melt spinning was used to produce binary alloys of Cu-Cr and Cu-Zr, and ternary alloys of Cu-Cr-Ag. By quenching from the liquid state, up to 5 atomic percent of Cr and Zr were retained in metastable extended solid solution during the rapid solidification process. Eutectic solidification was avoided and the full strengthening benefits of the large volume fraction of precipitates were realized by subsequent aging treatment. The very low solid solubility of Cr and Zr in Cu result in a high conductivity Cu matrix strengthened by second phase precipitates. Tensile properties on as-cast and aged ribbons were measured at room and elevated temperatures. Precipitate coarsening of Cr in Cu was studied by changes in electrical resistance during aging. X-ray diffraction was used to measure the lattice parameter and the degree of supersaturation of the matrix. The microstructures were characterized by optical and electron microscopy.

Bloom, Theodore Atlas↗

NASA NTRS1985

Electrical conductivity and phase diagram of binary alloys. 21: The system palladium-chromium

Pd-Cr alloys were investigated by thermal analysis, hardness measurements, X-ray analysis, microscopic examination of etched pieces, and temperature-resistance curves of the solid alloys. Only one compound, Pd2Cr3, m, 1389 deg, is formed. It possesses a cubic face centered lattice and forms with excess Pd a series of solid solutions with a minimum m.p. at 45 atoms% Pd. Hardness maximum appears at the Pd2Cr3 point. Pd2Cr3 forms no solid solutions with Cr but eutectic point appears at 25 atoms% Pd, m. 1320 deg. The sp. resistance of pure Cr in an atom of H, indicates no allotropic forms. Cr2O3 is solid in molten Cr. Pure Cr melts at 1890 plus or minus 10 deg but Cr contg. Cr2O3 starts to melt at 1770 to 1790 deg.

Grube, G.↗

NASA NTRS1987

Fluoride salts and container materials for thermal energy storage applications in the temperature range 973 to 1400 K

Multicomponent fluoride salt mixtures were characterized for use as latent heat of fusion heat storage materials in advanced solar dynamic space power systems with operating temperatures in the range of 973 to 1400 K. The melting points and eutectic composition for many systems with published phase diagrams were verified, and several new eutectic compositions were identified. Additionally, the heats of fusion of several binary and ternary eutectics and congruently melting intermediate compounds were measured by differential scanning calorimetry. The extent of corrosion of various metals by fluoride melts was estimated from thermodynamic considerations, and equilibrium conditions inside a containment vessel were calculated as functions of the initial moisture content of the salt and free volume above the molten salt. Preliminary experimental data on the corrosion of commercial, high-temperature alloys in LiF-19.5CaF2 and NaF-27CaF2-36MgF2 melts are presented and compared to the thermodynamic predictions.

Misra, Ajay K.↗

NASA NTRS1987

Fluoride salts and container materials for thermal energy storage applications in the temperature range 973 - 1400 K

Misra, Ajay K.↗