Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BENDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

The Building ENergy Demand (BEND) Model: A Comprehensive Composite Building Energy Modeling Framework

The Building ENergy Demand (BEND) model was developed at Pacific Northwest National Laboratory (PNNL) to simulate climate-dependent hourly building energy demand with the ability to disaggregate down to or aggregate up to any geographic area of interest, including counties, states, electric utility service territories, and census regions. The BEND modeling framework is designed to study the effects of climate change, economics, technology advancement, and various mitigation policies on aggregate building energy demand. To make the process computationally feasible, BEND reduces granularity in building characteristics and weather forcing while maintaining enough detail to minimize systematic differences (biases) between BEND results and data from the Energy Information Administration (EIA). Based on the Commercial Building Energy Consumption Survey (CBECS) and Residential Energy Consumption Survey (RECS) databases, BEND establishes a set of representative buildings with predefined sets of building types, sizes, and vintages. These representative buildings are defined for each of the four U.S. census regions and the five climate zones used by the EIA for building surveys (hereafter “EIA climate zones”). BEND’s representative buildings are based on a statistical analysis of the CBECS and RECS databases that infers detailed parameters such as construction type, thermal properties, internal loads, equipment and mechanical systems, and operation schedules from the high-level descriptors in those databases (building type, vintage, size, and location). The representative buildings are simplified and consolidated into a set of prototype buildings for the purpose of simulating building energy demand. Combining the prototype buildings with weather files from selected locations and years, BEND creates a set of simulation-ready building models to be run using the EnergyPlus simulation engine (EnergyPlus). The base spatial unit of each BEND simulation is a subregion that is the intersection of an International Energy Conservation Code climate zone, a census region, and an EIA climate zone; analysis for each spatial unit is influenced by the weather file BEND selects to represent the climate-similar area. The major simulation outputs of interest to BEND are hourly energy consumption values for each simulated year, possibly for multiple fuel types. Based on building-stock weights derived from the CBECS/RECS data, the hourly output streams are aggregated to a single, 8760-hour load profile for each of the major building categories—residential and commercial—with the possibility of segregating by fuel types. To correct for biases inherent in the use of a limited suite of representative buildings, BEND is calibrated against observational targets of total annual building energy consumption and hourly load profiles (including peak demand) obtained for the decision-relevant geographic scales of interest (e.g., total electric load data for individual balancing authorities available from EIA). Based on available data such as population distribution, BEND is able to aggregate both up and down scales, allowing the study of building energy demand over a range of spatial scales (e.g., states or counties within the Western Electricity Coordinating Council, Eastern Interconnection, or the entire U.S.) and/or subsets of building types (e.g., office buildings with particular size ranges).

24 POWER TRANSMISSION AND DISTRIBUTION↗

Dynamic Recrystallization and Metal Flow Behavior of AZ31 Magnesium Alloy Bending Products Processed by Staggered Extrusion

Traditional curved products are obtained in two steps, which consist of an extrusion process and a bending process. There are many bottlenecks to this, such as long processing cycle, low efficiency, and difficulty in controlling the product quality. In this paper, a new staggered extrusion (SE) process was proposed to obtain magnesium alloy bending products. Bending products can be extruded by a staggered punch which has a step-like structure at one end. The experimental results show that with increased staggered distance (h) of the punch, the bending height of the bending products increased significantly. Compared with traditional extrusion, the grains of the bending products obtained by SE are refined. The increase in h is one of the reasons for the asymmetric distribution of axial velocity at the die exit of AZ31 magnesium alloy bending products. The asymmetric distribution of the flow velocity field of bending products during SE is one of the contributors for the bending characteristics to the bending products. The SE enables the use of extrusion in many applicable fields and enriches the types of bending products.

36 MATERIALS SCIENCE↗

Ultrafast dynamics of liquid water: Energy relaxation and transfer processes of the OH stretch and the HOH bend

The vibrational energy relaxation and transfer processes of the OH stretching and the HOH bending vibrations in liquid water are investigated via the theoretical calculation of the pump-probe spectra obtained from non-equilibrium molecular dynamics simulations with the TTM3-F interaction potential. The excitation of the OH stretch induces an instantaneous response of the high frequency librational motions in the 600-1000 cm-1 range. In addition, the excess energy of the OH stretch of a water molecule quickly transfers to the OH stretches of molecules in its first hydration shell with a time constant of ~50 fs, followed by relaxation to the HOH bends of the surrounding molecules with a time constant of 230 fs. The excitation of the HOH bend also results in the ultrafast excitation of the high frequency librational motions. The energy of the excited HOH bend of a water molecule decays, with a time constant of 200 fs, mainly to the relaxation of the HOH bends of its surrounding molecules. The energies of the HOH bends were found to transfer quickly to the intermolecular motions via the coupling with the high frequency librational motions. The excess energy of the OH stretch or the HOH bend relaxes to the high frequency intermolecular librational motions and eventually to the hot ground state with a time scale of ~1 ps via the coupling with the librational and translational motions. The energy relaxation and transfer processes were found to depend on the local hydrogen bonding network; the relaxations of the excess energy of the OH stretch and the HOH bend of four- and five-coordinated molecules are faster than those of a three-coordinated molecule due to the delocalization of the vibrational motions of the former (four- and five-coordinated molecules) compared to those of the later (three-coordinated molecules). The present results highlight the importance of the high frequency intermolecular librational modes in facilitating the ultrafast energy relaxation process in liquid water via their strong nonlinear couplings with the intramolecular OH stretching and HOH bending vibrations. S.S.X. acknowledges the support of the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle. The calculation was carried out using the computing resources at the Research Center for Computational Science in Okazaki, Japan.

Imoto, Sho↗

Band bending at ferroelectric surfaces and interfaces investigated by x-ray photoelectron spectroscopy

This work reports on the use of X-ray photoelectron spectroscopy to quantify band bending at ferroelectric free surfaces and at their interfaces with metals. Surfaces exhibiting out-of-plane ferroelectric polarization are characterized by a band bending, due to the formation of a dipole layer at the surface, composed by the uncompensated polarization charges (due to ionic displacement) and to the depolarization charge sheet of opposite sign, composed by mobile charge carriers, which migrate near surface, owing to the depolarization electric field. To this surface band bending due to out-of-plane polarization states, metal-semiconductor Schottky barriers must be considered additionally when ferroelectrics are covered by metal layers. It is found that the net band bending is not always an algebraic sum of the two effects discussed above, since sometimes the metal is able to provide additional charge carriers, which are able to fully compensate the surface charge of the ferroelectric, up to the vanishing of the ferroelectric band bending. The two cases which will be discussed in more detail are Au and Cu deposited by molecular beam epitaxy on PbZr{sub 0.2}Ti{sub 0.8}O{sub 3}(001) single crystal thin layers, prepared by pulsed laser deposition. Gold forms unconnected nanoparticles, and their effect on the band bending is the apparition of a Schottky band bending additional to the band bending due to the out-of-plane polarization. Copper, starting with a given thickness, forms continuous metal layers connected to the ground of the system, and provide electrons in sufficient quantity to compensate the band bending due to the out-of-plane polarization.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Width-bending characteristic of REBCO HTS tape and flat-tape Rutherford-type cabling

Abstract The width-bending behaviors for a rare earth barium copper oxide (REBCO) high-temperature superconducting (HTS) tape have been investigated. It has been found experimentally that the width-bending strain of a Yttrium Barium Copper Oxide (YBCO) tape does not degrade the critical current as much as is expected from the axial strain. The critical current is not directly affected by the width-bending strain but by the axial strain, which the width-bending strain generates by the Poisson effect. Since Poisson’s ratio is about 0.3, the axial strain effective on the critical current is about 30% of the width-bending strain. Therefore, the width-bending strain of even 1.5% degrades the critical current by only 15% if the REBCO layer side is bent inward. However, the critical current degraded by more than 70% when the REBCO layer is outward. The width-bending effects on the critical current have been further examined, considering Poisson’s ratio changes and the neutral plane shift of the REBCO tape substrate. Those changes would occur when the material yields due to severe width-bending. Based on the width-bending of REBCO tapes, flat-tape Rutherford-type cabling is discussed. A REBCO Rutherford-type cable can provide various advantages, especially for narrow-tape cabling. The flat-tape Rutherford-type cable has better characteristics against an electromagnetic transverse Lorentz force. Furthermore, the tape length of the cable can be approximately the same as the cable length allowing for excellent tape usage. REBCO Rutherford-type cabling will be a promising high-current, high-field cabling method using thin substrate REBCO tapes. It will be useful for AC ramp-field and pulse-field applications with low AC losses and low shield currents. It notes that the filaments in the cable are symmetrically distributed in parallel. Therefore, each filament’s inductance is uniform, and a uniform current distribution among the filaments can be obtained.

Physics↗

Concept of the Complex Bend

Modern synchrotron lattices follow Multi-­Bend Achromat approach and realize low emittance by arranging small horizontal beta-­function and dispersion in the bends. In this paper we propose another optics solution aimed to reach low emittance by using a lattice element that we named as “Complex Bend”. The Complex Bend corresponds to a strong alternate focusing distributed along the bend so to maintain the beta-function and dispersion oscillating at low values. Comprising the ring lattice out of Complex Bends instead of regular dipoles will minimize the Ң-­function and reduce the horizontal emittance while localizing bending to a small fraction of the storage ring circumference. The latter should help to gain more space for Insertion Devices. In the following, we present the concept of Complex Bend, considerations on the choice of its optimal parameters, as well as, thoughts of its practical realization. This paper gives a snapshot where our current studies stand and does not pretend to be a complete description of the Complex Bend engineering design and integration of this element into a specific ring lattice.

36 MATERIALS SCIENCE↗

Effects of Transition Layer on Bending Resistance in Copper-Clad Aluminum Composite Casting

The performance of the transition layer in a Cu/Al composite casting directly affects the quality of subsequent plastic deformation processing; however, there are no universal or standardized measurement indices for the performance of the transition layer. In this study, Cu/Al composite castings were prepared using the pouring aluminum method, and the resulting solidification microstructures on the bending resistance were investigated. The results of this study lay a theoretical foundation for the development of the plastic processing technologies of these composite castings. A thinner transition layer in the Cu/Al composite casting led to improved bending resistance. In addition, for a fixed total thickness of the transition layer, the bending resistance was mainly controlled by the γ/β interface and β + eutectic (α + β) microstructure, and the thickness of the γ phase had a negligible effect on the bending resistance. The γ/β interface cracked first when the transition layer bore the tensile and shear stress during the bending process, which resulted in the transition layer easily separating from the copper. The bending resistance of the transition layer can be feasibly judged by measuring the bending angle of the specimen tip, which can be easily performed when the specimen bends toward the aluminum direction, suggesting that our proposed method has considerable practical significance.

36 MATERIALS SCIENCE↗

TEST SYSTEM FOR EVALUATING SPENT NUCLEAR FUEL BENDING STIFFNESS AND VIBRATION INTEGRITY

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements specified by federal regulations. For normal conditions of transport, vibration loads incident to transport must be considered. This is particularly relevant for high-burnup fuel (>45 GWd/MTU). As the burnup of the fuel increases, a number of changes occur that may affect the performance of the fuel and cladding in storage and during transportation. The mechanical properties of high-burnup de-fueled cladding have been previously studied by subjecting defueled cladding tubes to longitudinal (axial) tensile tests, ring-stretch tests, ring-compression tests, and biaxial tube burst tests. The objective of this study is to investigate the mechanical properties and behavior of both the cladding and the fuel in it under vibration/cyclic loads similar to the sustained vibration loads experienced during normal transport. The vibration loads to SNF rods during transportation can be characterized by dynamic, cyclic, bending loads. The transient vibration signals in a specified transport environment can be analyzed, and frequency, amplitude and phase components can be identified. The methodology being implemented is a novel approach to study the vibration integrity of actual SNF rod segments through testing and evaluating the fatigue performance of SNF rods at defined frequencies. Oak Ridge National Laboratory (ORNL) has developed a bending fatigue system to evaluate the response of the SNF rods to vibration loads. A three-point deflection measurement technique using linear variable differential transformers is used to characterize the bending rod curvature, and electromagnetic force linear motors are used as the driving system for mechanical loading. ORNL plans to use the test system in a hot cell for SNF vibration testing on high burnup, irradiated fuel to evaluate the pellet-clad interaction and bonding on the effective lifetime of fuel-clad structure bending fatigue performance. Technical challenges include pure bending implementation, remote installation and detachment of the SNF test specimen, test specimen deformation measurement, and identification of a driving system suitable for use in a hot cell. Surrogate test specimens have been used to calibrate the test setup and conduct systematic cyclic tests. The calibration and systematic cyclic tests have been used to identify test protocol issues prior to implementation in the hot cell. In addition, cyclic hardening in unidirectional bending and softening in reverse bending were observed in the surrogate test specimens. The interface bonding between the surrogate clad and pellets was found to impact the bending response of the surrogate rods; confirming this behavior in the actual spent fuel segments will be an important aspect of the hot cell test implementation,

reversal bending fatigue tester↗

Residual stresses distribution, correlated with bending tests, within explosively welded Ti gr. 2/A1050 bimetals

Highlights: • Ti gr.2/A1050 clad was slightly affected by the explosive welding since negative sign values of stress tensor were detected. • Upon bending higher negative compression stresses were detected in this area. • Twins morphology changed from parallel to cross-shaped arrangement as a consequence of bending. • The compressive twinning was the dominant system before and after three point bending. - Abstract: Synchrotron radiation and XRD{sup 2} method were used to investigate the residual stress distribution before and after three point bending tests within an explosively welded composite composed of two light metals, namely: Ti gr. 2 and A1050. The analysis has shown that the bimetal is slightly affected by the explosive welding process since negative sign values of stress tensor were detected only in the immediate vicinity of interface of Ti gr. 2 characterized by a width of about 0.25 mm. Upon bending higher negative compression stresses are detected in this area as the σ{sub 11} value changes from −500 MPa to −1200 MPa. Additionally, the analysis of microstructure has revealed significant changes in twins morphology with primary and conjugate twinning before and after bending, respectively. However, the compressive twinning was the dominant system in both cases. Bending has changed the initial bimodal texture developing more spread basal components towards the transverse direction. The sample surface has been also significantly affected as the presence of compressive residual stress (−500 MPa) after bending was measured.

36 MATERIALS SCIENCE↗

Bending-induced isostructural transitions in ultrathin layers of van der Waals ferrielectrics

Using Landau-Ginzburg-Devonshire (LGD) phenomenological approach we analyze the bending-induced re-distribution of electric polarization and field, elastic stresses and strains inside ultrathin layers of van der Waals ferrielectrics. We consider a CuInP2S6 (CIPS) thin layer with fixed edges and suspended central part, the bending of which is induced by external forces. The unique aspect of CIPS is the existence of two ferrielectric states, FI1 and FI2, corresponding to big and small polarization values, which arise due to the specific four-well potential of the eighth-order LGD functional. When the CIPS layer is flat, the single-domain FI1 state is stable in the central part of the layer, and the FI2 states are stable near the fixed edges. With an increase of the layer bending below the critical value, the sizes of the FI2 states near the fixed edges decreases, and the size of the FI1 region increases. When the bending exceeds the critical value, the edge FI2 states disappear being substituted by the FI1 state, but they appear abruptly near the inflection regions and expand as the bending increases. The bending-induced isostructural FI1-FI2 transition is specific for the bended van der Waals ferrielectrics described by the eighth (or higher) order LGD functional with consideration of linear and nonlinear electrostriction couplings. Furthermore, the isostructural transition, which is revealed in the vicinity of room temperature, can significantly reduce the coercive voltage of ferroelectric polarization reversal in CIPS nanoflakes, allowing for the curvature-engineering control of various flexible nanodevices.

36 MATERIALS SCIENCE↗

Experimental and computational analysis of bending fatigue failure in chopped carbon fiber chip reinforced composites

With a better balance among good mechanical performance, high freedom of design, and low material and manufacturing cost, chopped carbon fiber chip reinforced sheet molding compound (SMC) composites show great potential in different engineering applications. Here in this paper, bending fatigue behaviors of SMC composites considering the heterogeneous fiber orientation distributions have been thoroughly investigated utilizing both experimental and computational methods. First, four-point bending fatigue tests are performed with designed SMC composites, and the local modulus is adopted as a metric to represent the local fiber orientation of two opposing sides. Interestingly, SMC composites with and without large discrepancy in local modulus of opposing sides show different fatigue behaviors. Interrupted tests are conducted to explore the bending fatigue failure mechanism, and the damage processes of valid specimens are also closely examined. We find that the fatigue failure of SMC composites under four-point bending is governed by crack propagation instead of crack initiation. Because of this, the heterogeneous local fiber orientations of both sides of the specimen influence fatigue life. The microstructure of the lower side shows a direct influence while that of the upper side also exhibiting influence which becomes more prominent for high cycle fatigue cases. Furthermore, a hybrid micro–macro computational model is proposed to efficiently study the cyclic bending behavior of SMC composites. The region of interest is reconstructed with a modified random sequential absorption algorithm to conserve all the microstructural details including the heterogeneous fiber orientation, while the rest of the regions are modeled as homogenized macro-scale continua. Combined with a framework to capture the progressive fatigue damage under cyclic bending, the bending fatigue behaviors of SMC composites are accurately captured by the hybrid computational model comparing with our experimental analysis.

36 MATERIALS SCIENCE↗

Development of U-Frame Bending System for Studying the Vibration Integrity of Spent Nuclear Fuel

A bending fatigue system developed to evaluate the response of spent nuclear fuel rods to vibration loads is presented. Design and analysis, fabrication, modification, calibration, and instrumentation are described. The system is composed of a U-frame testing setup for imposing bending loads on the spent fuel rod test specimen and a method for measuring the curvature of the rod during bending. The U-frame setup consists of two rigid arms, linking members, and linkages to a universal testing machine. The test specimen s curvature of bending is obtained through a three-point deflection measurement method consisting of three LVDTs mounted to the side connecting plates of the U-frame to capture the deformation of the test specimen. The system has some unique features: 1) The test specimen is installed by simple insertion using linear bearings incorporated with rigid sleeves. 2) Reverse cyclic bending tests can be carried out effectively and efficiently by push and pull at the loading point of the setup. Any test machine with a linear motion function can be used to drive the setup. 3) The embedded and preloaded linear roller bearings eliminate the backlash that exists in the conventional reverse bend tests. 4) The number of linkages between the U-frame and the universal machine is minimized. Namely, there are only two linkages needed at the two loading points of a U-frame setup, whereas a conventional four/three-point bend test frame requires four linkages. 5) The curvature measurement is immune to the effects arising from compliant layers and the rigid body motion of the machine. The compliant layers are used at the holding areas of the specimen to prevent contact damage. The tests using surrogate specimens composed of SS cladding/tube revealed several important phenomena that may cast light on the expected response of a spent fuel rod: 1) Cyclic quasi-static load (10 N/s under force control) in compressive mode (with respect to that at the loading point of the U-frame) produced increased irreversible or plastic curvature and also increased flexural rigidity of the surrogate rod. 2) Dynamic cyclic load (at least 1 Hz) in compressive mode resulted in increased flexural rigidity of the surrogate rod prior to SS cladding fracture. 3) Pellets and epoxy bonding exhibited various effects on the response of surrogate rods during the loading process as validated from static tests. 4) Dynamic cyclic load (2 Hz) in reverse mode demonstrated a substantial cyclic softening before the fracture of the surrogate rod. The degree of decrease in flexural rigidity was consistent in both measurement and on-line monitoring. The developed U-frame system is thus verified and demonstrated to be ready for further pursuit in hot-cell tests.

fuel transporation↗

Birefringence imaging and orientation of laser patterned β-BaB{sub 2}O{sub 4} crystals with bending and curved shapes in glass

Nonlinear optical β-BaB{sub 2}O{sub 4} crystals (β-BBO) with bending and curved shapes were patterned at the surface of 8Sm{sub 2}O{sub 3}–42BaO–50B{sub 2}O{sub 3} glass by laser irradiations (Yb:YVO{sub 4} laser with a wavelength of 1080 nm, power of 0.8 W, and scanning speed of 4 μm/s), and the orientation state of β-BBO crystals was examined from the birefringence imaging obtained by polarization optical microscope (POM) observations. The formation (crystallization) of β-BBO crystals follows along laser scanning direction even if the laser scanning direction changes at a certain point within the bending angle of 60°. The birefringence images indicate that the formation of highly c-axis oriented β-BBO crystals follows along laser scanning direction even if the laser scanning direction changes, and in particular the direction of the c-axis of β-BBO crystals changes gradually at the bending point. The model for the orientation of the c-axis of β-BBO near the bending point is proposed. The present study proposes that the laser-induced crystallization opens a new door for the science and technology in crystal growth engineering. - Graphical abstract: This figure shows the birefringence images obtained by the Abrio IM imaging system (λ=546 nm) for the laser-patterned β-BaB{sub 2}O{sub 4} crystal line with the bending angle of 45° in the glass. The relation between the direction of slow axis and color is also shown. It is demonstrated that the formation (crystallization) of highly c-axis oriented β-BaB{sub 2}O{sub 4} crystals follows along laser scanning direction even if the laser scanning direction changes. Display Omitted - Highlights: • β-BaB{sub 2}O{sub 4} crystals with bending and curved shapes were patterned by laser irradiations. • The orientation was examined from the birefringence imaging. • Highly c-axis oriented crystals follows along laser scanning direction. • The c-axis direction changes gradually at the bending point. • The laser-induced crystallization opens a new door in crystal growth engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ion beam-induced bending of TiO 2 nanowires with bead-like and prismatic shapes

Ion beam irradiation is a promising method to manipulate the composition and shape of nanowires. It causes the formation of crystal defects like vacancies and dislocations, and consequently, a volume expansion within the irradiated region, giving rise to the nanowire bending. The bending effect has been extensively discussed within nanowires with different diameters under ion beams with varying energies and ion fluences. However, the behaviors of nanowires with complicated shapes, which may have non-uniform irradiated regions due to the changing angle of incidence and shadowing effect, have remained largely unknown. Herein, the structural changes and bending of TiO 2 nanowires with both bead-like and prismatic shapes are investigated under a Ga + ion beam. The multi-faceted morphology, and consequently, varying angles of incidence, result in inhomogeneous irradiation and volume expansion. As a result, significant bending is only observed in prismatic nanowires. Since irradiation is confined within the half of nanowires facing the ion beam, the bending of nanowires is reversible by changing the direction of the ion beam. In order to provide insights into the tailoring composition and morphology of nanowires, we anticipate that this finding can establish the beam analog at the nanoscale, the bending of which can be tuned by ion irradiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Study On Critical Thinning In Thin-walled Tube Bending Of Al-Alloy 5052O Via Coupled Ductile Fracture Criteria

Thin-walled tube bending(TWTB) method of Al-alloy tube has attracted wide applications in aerospace, aviation and automobile,etc. While, under in-plane double tensile stress states at the extrados of bending tube, the over-thinning induced ductile fracture is one dominant defect in Al-alloy tube bending. The main objective of this study is to predict the critical wall-thinning of Al-alloy tube bending by coupling two ductile fracture criteria(DFCs) into FE simulation. The DFCs include Continuum Damage Mechanics(CDM)-based model and GTN porous model. Through the uniaxial tensile test of the curved specimen, the basic material properties of the Al-alloy 5052O tube is obtained; via the inverse problem solution, the damage parameters of both the two fracture criteria are interatively determined. Thus the application study of the above DFCs in the TWTB is performed, and the more reasonable one is selected to obtain the critical thinning of Al-alloy tube in bending. The virtual damage initiation and evolution (when and where the ductile fracture occurs) in TWTB are investigated, and the fracture mechanisms of the voided Al-alloy tube in tube bending are consequently discussed.

36 MATERIALS SCIENCE↗

Theoretical and experimental study of the bending influence on the capacitance of interdigitated micro-electrodes patterned on flexible substrates

Interdigitated electrodes are common structures in the fields of microelectronics and MEMS. Recent developments in flexible electronics compel an understanding of such structures under bending constraints. In this work, the behavior of interdigitated micro-electrodes when subjected to circular bending has been theoretically and experimentally studied through changes in capacitance. An analytical model has been developed to calculate the expected variation in capacitance of such structures while undergoing outward and inward bending along the direction perpendicular to the electrodes. The model combines conformal mapping techniques to account for the electric field redistribution and fundamental aspects of solid mechanics in order to define the geometrical deformation of the electrodes while bending. To experimentally verify our theoretical predictions, several interdigitated electrode structures with different geometries were fabricated on polymeric substrates by means of photolithography. The samples, placed in a customized bending setup, were bent to controlled radii of curvature while measuring their capacitance. A maximum variation in capacitance of less than 3% was observed at a minimum radius of curvature of 2.5 mm for all the devices tested with very thin electrodes whereas changes of up to 7% were found on stiffer, plated electrodes. Larger or smaller variations would be possible, in theory, by adjusting the geometry of the device. This work establishes a useful predictive tool for the design and evaluation of truly flexible/bendable electronics consisting of interdigitated structures, allowing one to tune the bending influence on the capacitance value through geometrical design.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗