Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “B2O3”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Fabrication and surface characterization of composite refractory compounds suitable for thermionic converters

Procedures for fabricating high purity single crystals of LaB6 and SmB6 have been developed. Auger spectroscopy shows that a clean surface can be obtained by thermal heating at 1700 K; such a clean surface gives a value of B/La of 2.3 to 2.6 for the (100) face. The measured thermionic and FERP work functions of the (100) face of LaB6 are 2.47 and 2.28 eV, respectively. The electron reflection coefficient for LaB6(100) increases near zero primary energy to 0.5. Flash thermal desorption of an oxygen dosed surface showed that B2O3 is the desorption product at 1600 to 1700 K. A work function increase of 1.6 eV was observed on oxygen adsorption on LaB6(100). Thermal desorption of Co occurs at approximately 1300 K. A reduction of the work function to 1.39 eV was observed on adsorption of a partial monolayer of Cs on LaB6(100). The evaporation of LaB6 occurs as atomic La and B with a value of B/La of 6 to 3 in the temperature range 1700 to 2000 K. The activation energies of desorption for La and B are 6.3 + or - 0.3 and 6.8 + or - 0.3 eV, respectively.

Swanson, L. W.↗
NASA NTRS1978

Experimental studies of the formation/deposition of sodium sulfate in/from combustion gases

Interference in a reflected beam of monochromatic light from a linearly polarized helium-neon laser was used to determine the dew point and deposition rate of B2O3 on a heated platinum target. Preliminary results at different BCl3 seed levels, except for one flow velocity and equivalence ratio (.813) are presented and discussed. Alkali chloride reactions with atomic oxygen were also investigated. Readily detectable Na*(g) and K*(g) - atoms were observed in emission at 589 nm, 766nm, 796nm, respectively.

Rosner, D. E.↗
NASA NTRS1979

Experimental studies of the formation/deposition of sodium sulfate in/from combustion gases

An optical polarization (ellipsometric) technique was developed for measuring rapidly growing and evaporating transparent liquid condensate films (e.g., boric oxide) on solid surfaces exposed to combustion product gases. Results for the B2O3 deposition rate from BCl3-seeded propane/air flames are shown to agree well with the results of earlier interference measurements, and also with theoretical CVD predictions. Evaporation rates (from platinum ribbons into seeded propane air flames) are estimated using the polarization technique. It appears that, compared with the interference method, the polarization technique places less stringent requirements on surface quality, which may justify the added optical components needed for such measurements. It is concluded that the complementary optical methods of polarization (ellipsometry) and interference hold considerable promise for application to the rapid measurement of condensation and evaporation rates in high temperature (e.g., combustion product) environments.

Rosner, D. E.↗
NASA NTRS1979

Development of high viscosity coatings for advanced Space Shuttle applications

Laboratory studies for increasing the thermal resistance of high viscosity coatings for silica reusable surface insulation are presented. The coatings are intended for the reentry temperature associated with advanced Space Shuttle applications which will involve aerodynamic shear forces during entry from earth orbits. Coating viscosity was increased by (1) reduction in the concentration of the low viscosity additive B2O3; (2) reduction in the particle size of the constituent powders in coatings; and (3) addition of a high viscosity glass former (GeO2). A coating system was produced by combining the three methods which showed apparent higher viscosity than the current coating, while satisfying all the current Shuttle Orbiter coating requirements.

Garofalini, S. H.↗
NASA NTRS1981

Adjustable high emittance gap filler

A flexible, adjustable refractory filler is disclosed for filling gaps between ceramic tiles forming the heat shield of a space shuttle vehicle, to protect its aluminum skin during atmospheric reentry. The easily installed and replaced filler consists essentially of a strip of ceramic cloth coated, at least along both its longitudinal edges with a room temperature vulcanizable silicone rubber compound with a high emittance colored pigment. The filler may have one or more layers as the gap width requires. Preferred materials are basket weave aluminoborosilicate cloth, and a rubber compounded with silicon tetraboride as the emittance agent and finely divided borosilicate glass containing about 7.5% B2O3 as high temperature binder. The filler cloth strip or tape is cut to proper width and length, inserted into the gap, and fastened with previously applied drops of silicone rubber adhesive.

Leiser, D. B.↗
NASA NTRS1974

High modulus invert analog glass compositions containing beryllia

Glass compositions having a Young's modulus of at least 15 million psi and a specific modulus of at least 110 million inches consisting essentially of, in mols, 10-45% SiO2, 2-15% Li2O, 3-34% BeO, 12-36% of at least one bivalent oxide selected from the group consisting of CaO, ZnO, MgO and CuO, 10-39% of at least one trivalent oxide selected from the group consisting of Al2O3, B2O3, La2O3, Y2O3 and the mixed rare earth oxides, the total number of said bivalent and trivalent oxides being at least three, and up to 10% of a tetravalent oxide selected from the group consisting of ZrO2, TiO2 and CeO2.

Bacon, J. F.↗
NASA NTRS1974

Non-toxic invert analog glass compositions of high modulus

Glass compositions having a Young's modulus of at least 15 million psi are described. They and a specific modulus of at least 110 million inches consist essentially of, in mols, 15 to 40% SiO2, 6 to 15% Li2O, 24 to 45% of at least two bivalent oxides selected from the group consisting of Ca, NzO, MgO and CuO; 13 to 39% of at least two trivalent oxides selected from the group consisting of Al2O3, Fe2O3, B2O3, La2O3, and Y2O3 and up to 15% of one or more tetravelent oxides selected from the group consisting of ZrO2, TiO2 and CeO2. The high modulus, low density glass compositions contain no toxic elements. The composition, glass density, Young's modulus, and specific modulus for 28 representative glasses are presented. The fiber modulus of five glasses are given.

Bacon, J. F.↗
NASA NTRS1982

The redox potential of boron nitride and implications for its use as a crucible material in experimental petrology

The suitability of boron nitride for use as a crucible material in silicate and oxygen-bearing metal sulfide systems has been investigated. Boron nitride is unsatisfactory for use with many silicate systems because its presence in combination with a source of oxygen establishes the oxygen fugacity at values below that of the assemblage quartz + fayalite + iron, reducing transition metal ions such as Ni(2+) and Fe(2+) to the metallic state. B2O3, resulting from the oxidation of BN, acts as a flux to promote formation of melt.

Wendlandt, R. F.↗
NASA NTRS1982

Liquid encapsulated Czochralski growth of low dislocation GaAs

The availability of high-quality, large-diameter GaAs substrates is key to the successful development and production of high-speed GaAs devices and high-efficiency GaAs solar cells. The liquid encapsulated Czochralski (LEC) technique has provided a means for producing large-diameter GaAs. Progress in improving the LEC growth process which has resulted in 3-inch GaAs crystals with exceptionally low dislocation densities and reduced propensity for twinning is reported. Undoped, semi-insulating GaAs ingots were grown in a Melbourn high-pressure LEC system. The effects of seed perfection, seed necking, cone angle, melt stoichiometry, ambient pressure, thickness of the B2O3 encapsulating layer, and diameter control on the dislocation density were investigated. The material was characterized by preferential etching and X-ray topography. It is shown that 3-inch diameter substrates can be produced with dislocation densities as low as 6000 per sq cm through proper selection and control of growth parameters. Also, the incidence of twinning can be reduced significantly by growing from slightly As-rich melts.

Kirkpatrick, C. G.↗
NASA NTRS1985

Undercooling of molten silicon

Droplets of uncoated molten Si(0.4-0.8 mm diameter) have been undercooled 250 C. Ge droplets of similar size have been undercooled 280 C in a B2O3 flux. The observed nucleation onset temperatures of both Si and Ge droplets are at or below the predicted amorphous phase melting temperatures T(al). The solidified structures were polycrystalline. The nucleation frequency I, calculated from the Si data (20,000/cu cm s at 240 + or - 20 C undercooling), should be an upper limit of the homogeneous nucleation frequency of the crystal phase, since it has not been established that nucleation was homogeneous in these experiments. However, this limiting I for Si indicates that homogeneous nucleation of crystal would not become appreciable in laser pulsing experiments until the liquid Si is undercooled to well below T(al).

Devaud, G.↗
NASA NTRS1985

Bulk Formation of Metallic Glasses and Amorphous Silicon from the Melt

By using metallic glass compositions with a high relative glass transition temperature, such as Pd40Ni40P20, homogeneous nucleation also becomes negligible. Large (5g) masses of this alloys were obtained using a molten B2O3 flux. Presently, bulk glass formation in iron based glasses is being investigated. It is expected that if an undercooling of about 250K can be achieved in a Ge or Si melt, formation of the amorphous semiconductor phase (rather than the crystal) may be kinetically favored. The volumetric behavior of undercooled liquid Ga droplet dispersion is investigated by dilatometry. A theoretical model (both analytical and numerical) was developed for transient nucleation in glass forming melts. The model, originally designed for isothermal conditions, was extended to continuous quenching. It is being applied to glass formation in various metallic and oxide systems. A further refinement will be the inclusion of diffusion controlled interfacial rearrangements governing the growth of the crystal embryos.

Spaepen, F.↗
NASA NTRS1987

Practical significance and calculation of surface tension of glass, enamels and glazes

Surface tension is important in the formation of streaks in the whole procedure of enameling and glazing., in the action of TiO2 as opacifier, in the addition of borax to enamels, or metals to glasses, and in the corrosion of refractories by molten charges. By the use of known methods for measuring surface tension additive constants are found which give correct results within 1% with no discrepancy due to B2O3.

Dietzel, A.↗
NASA NTRS1985

Melting of Ni40Pd40P20 glass

Upon reheating, most glassy metal alloys crystallize at a temperature not far removed from the glass temperature Tg and far below the liquidus temperature T1. It has been reported by Kui et al. (1984) that the alloy Ni40Pd40P20, which exhibits a scaled glass temperature of about 0.68, has been melt quenched, under a flux of dehydrated B2O3, to a glass at rates as low as 1 deg/s. Here some specimens of this alloy, when similarly fluxed during reheating, have been reheated to temperatures within 50 deg of T1 and 280 deg above Tg at rates of about 2.5 deg/s, and then cooled again to Tg, without crystallization. From this behavior it is inferred that the steady frequency of homogeneous nucleation of crystals in the alloy is less than 0.1/cu cm s.

Kui, H. W.↗
NASA NTRS1992

Glass precursor approach to high-temperature superconductors

The available studies on the synthesis of high T sub c superconductors (HTS) via the glass precursor approach were reviewed. Melts of the Bi-Sr-Ca-Cu-O system as well as those doped with oxides of some other elements (Pb, Al, V, Te, Nb, etc.) could be quenched into glasses which, on further heat treatments under appropriate conditions, crystallized into the superconducting phase(s). The nature of the HTS phase(s) formed depends on the annealing temperature, time, atmosphere, and the cooling rate and also on the glass composition. Long term annealing was needed to obtain a large fraction of the 110 K phase. The high T sub c phase did not crystallize out directly from the glass matrix, but was preceded by the precipitation of other phases. The 110 K HTS was produced at high temperatures by reaction between the phases formed at lower temperatures resulting in multiphase material. The presence of a glass former such as B2O3 was necessary for the Y-Ba-Cu-O melt to form a glass on fast cooling. A discontinuous YBa2Cu3O(7-delta) HTS phase crystallized out on heat treatment of this glass. Attempts to prepare Tl-Ba-Ca-Cu-O system in the glassy state were not successful.

Bansal, Narottam P.↗
NASA NTRS1997

The Effect of Gravity on the Combustion Synthesis of Porous Ceramics and Metal Matrix Composites

Combustion synthesis (self propagating, high temperature synthesis-SHS) is a novel technique that is capable of producing many advanced materials. The ignition temperature (Tig) of such combustion synthesis reactions is often coincident with that of the lowest melting point reactant. The resultant liquid metal wets and spreads around the other solid reactant particles of higher melting points, thereby improving the reactant contact and kinetics, followed by formation of the required compounds. This ignition initiates a combustion propagating wave whose narrow reaction front rapidly travels through the reactants. Since this process is highly exothermic, the heat released by combustion often melts the reactant particles ahead of the combustion front and ignites the adjacent reactant layer, resulting in a self-sustaining reaction. Whenever a fluid phase (liquid or gas) is generated by the reaction system, gravity-driven phenomena can occur. Such phenomena include convective flows of fluid by conventional or unstable convection and settling of the higher density phases. A combustion process is often associated with various kinds of fluid flow. For instance, if the SHS reaction is carried out under inert or reactive gas atmospheres, or a volatile, e.g., B2O3, is deliberately introduced as a reactant, convective flows of the gas will occur due to a temperature gradient existing in the atmosphere when a combustion wave is initiated. The increased gas flow will produce a porous (or expanded) SHS product. Owing to the highly exothermic nature of many SHS reactions, liquid phase(s) can also form before, at, or after the combustion front. The huge temperature gradient at the combustion front can induce convective flows (conventional or unstable) of the liquid phase. Each of these types of convective fluid flow can change the combustion behavior of the synthesizing reaction, and, therefore, the resultant product microstructure. In addition, when two or more phases of different density are produced at or ahead of the propagating combustion front settling of the higher density phase will occur resulting in a non-uniform product microstructure and properties.

Moore, J. J.↗
NASA NTRS2000

Gravity Effects on Combustion Synthesis of Glasses

The Combustion Synthesis technique has been used to produce glasses based on B2O3-Al2O3-MgO and CaO-Al2O3. The combustion characteristics of these combustion synthesis reactions using both small cylindrical pellets (SCP) and large spherical pellets (LSP) are presented. Low density pellets (approx. 35% of their theoretical density) were used, which made synthesis of low exothermic combustion reactions possible. Microstructural analysis of reacted samples was carried out to identify the glass-forming compositions. The effects of gravity on the glass formation were studied aboard the KC-135 using SCP samples. Gravity seemed to have such obvious effects on the combustion characteristics that the wave velocity was lower and the Width of the combustion wave was larger under reduced gravity conditions. Samples produced under low gravity also had more enhanced vitrification than those on ground, while some systems also exhibited lower combustion temperatures. It was also found that the container significantly affects both the combustion characteristics and microstructure. Substantially more divitrification occurred at the area which was in contact with the support (container).

Yi, H. C.↗
NASA NTRS1997

High Temperature Oxidation of Boron Nitride: Monolithic Boron Nitride - Part 1

High temperature oxidation of monolithic boron nitride (BN) is examined. Hot pressed BN and both low and high density CVD BN were studied. It is shown that oxidation rates are quite sensitive to microstructural factors such as orientation, porosity, and degree of crystallinity. In addition small amounts of water vapor lead to volatilization of the B2O3 oxide as H(x)B(y)O(z). For these reasons, very different oxidation kinetics were observed for each type of BN.

Jacobson, Nathan↗