Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Axial Compressors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

The effect of adding roughness and thickness to a transonic axial compressor rotor

The performance deterioration of a high speed axial compressor rotor due to surface roughness and airfoil thickness variations is reported. A 0.025 mm (0.001 in.) thick rough coating with a surface finish of 2.54-3.18 RMS microns (100-125 RMS microinches) is applied to the pressure and suction surface of the rotor blades. Coating both surfaces increases the leading edge thickness by 10% at the hub and 20% at the tip. Application of this coating results in a loss in efficiency of 6 points and a 9% reduction in the pressure ratio across the rotor at an operating condition near the design point. To separate the effect of thickness and roughness, a smooth coating of equal thickness is also applied to the blade. The smooth coating surface finish is 0.254-0.508 RMS microns (10-20 RMS microinches), compared to the bare metal blade surface finish of 0.508 RMS microns (20 RMS microinches). The smooth coating results in approximately half of the performance deterioration found from the rough coating. Both coatings are then applied to different portions of the blade surface to determine which portions of the airfoil are most sensitive to thickness/roughness variations. Aerodynamic performance measurements are presented for a number of coating configurations at 60%, 80%, and 100% of design speed. The results indicate that thickness/roughness over the first 10% of blade chord accounts for virtually all of the observed performance degradation for the smooth coating, compared to about 70% of the observed performance degradation for the rough coating. The performance deterioration is investigated in more detail at design speed using laser anemometer measurements as well as predictions generated by a quasi-3D Navier-Stokes flow solver which includes a surface roughness model. Measurements and analysis are performed on the baseline blade and the full-coverage smooth and rough coatings. The results indicate that coating the blade causes a thickening of the blade boundary layers. The interaction between the rotor passage shock and the thickened suction surface boundary layer then results in an increase in blockage which reduces the diffusion level in the rear half of the blade passage, thus reducing the aerodynamic performance of the rotor.

Suder, Kenneth L.↗
NASA NTRS2017

Impact of Wake Dispersion on Axial Compressor Performance

Detailed development of wakes and their impact on the performance of a low-speed one and half stage axial compressor are investigated with a large eddy simulation (LES). To investigate effects of wake mixing recovery and wake interaction with the boundary layer of the downstream blade, spacing between the rotor blade and the stator is varied. The calculated LES flow fields based on a fine computational grid are compared with related measurements and analyzed in detail at several radial locations. The current LES calculates the effects of wake recovery very well. The effects of wake recovery vary significantly in the radial direction. Loss generation is higher on the pressure side at the stator exit at both near design and near stall condition. The current investigation indicates that better management of wake development can be achieved for improved compressor performance.

LES↗
NASA NTRSDate not supplied

Characterization of the Upgraded NASA GRC Single Stage Axial Compressor and Fan Facility

In order to meet the emissions and efficiency goals established by the aviation community, next generation aircraft engines will require low pressure ratio, distortion tolerant fans. Maturation of the necessary technologies will require facilities capable of accurately testing the fan performance are needed. To achieve this, the Single Stage Axial Compressor and Fan facility at NASA Glenn Research Center was upgraded. Details of the goals and upgrades undertaken were documented in the 2022 Turbo Expo paper, “Upgrades to the Single Stage Axial Compressor and Fan Facility for Low Pressure Ratio Boundary Layer Ingesting Fan Research.” The performance of the upgraded facility will be documented in this paper. This paper will review the challenges associated with testing low pressure ratio and distortion tolerant fans and briefly review the upgrades undertaken and their goals. Then the performance of the facility upgrades and the extent to which they were able to achieve the stated goals. This includes mass flow measurements, test section temperature, pressure, flow angle at two axial locations, and turbulence levels at the inlet and test section. The paper also documents the performance of distortion generating swirl vanes and total pressure screens to achieve desired distorted conditions at the Aerodynamic Interface Plane.

BLI↗
NASA NTRSDate not supplied

Characterization of the Upgraded NASA GRC Single Stage Axial Compressor and Fan Facility

In order to meet the emissions and efficiency goals established by the aviation community, next generation aircraft engines will require low pressure ratio, distortion tolerant fans. Maturation of the necessary technologies will require facilities which are capable of accurately testing the fan performance. To achieve this, the Single Stage Axial Compressor and Fan facility at NASA Glenn Research Center was upgraded. Details of the goals and upgrades undertaken were documented in the 2022 Turbo Expo paper, “Upgrades to the Single Stage Axial Compressor and Fan Facility for Low Pressure Ratio Boundary Layer Ingesting Fan Research.” The performance of the upgraded facility will be documented in this paper. This paper will review the challenges associated with testing low pressure ratio and distortion tolerant fans and briefly review the upgrades undertaken and their goals. Then the performance of the facility upgrades and the extent to which they were able to achieve the stated goals will be discussed. This includes mass flow measurements, test section temperature, pressure, flow angle at two axial locations, and turbulence levels at the inlet and test section. The paper also documents the performance of distortion generating swirl vanes and total pressure screens to achieve desired distorted conditions at the Aerodynamic Interface Plane.

BLI↗
NASA NTRS1983

A theory of rotating stall of multistage axial compressors

A theoretical analysis was made of rotating stall in axial compressors of many stages, finding conditions for a permanent, straight-through traveling disturbance, with the steady compressor characteristic assumed known, and with simple lag processes ascribed to the flows in the inlet, blade passages, and exit regions. For weak disturbances, predicted stall propagation speeds agree well with experimental results. For a locally-parabolic compressor characteristic, an exact nonlinear solution is found and discussed. For deep stall, the stall-zone boundary is most abrupt at the trailing edge, as expected. When a complete characteristic having unstalling and reverse-flow features is adopted, limit cycles governed by a Lienard's equation are found. Analysis of these cycles yields predictions of recovery from rotating stall; a relaxation oscillation is found at some limiting flow coefficient, above which no solution exists. Recovery is apparently independent of lag processes in the blade passages, but instead depends on the lags originating in the inlet and exit flows, and also on the shape of the given characteristic diagram. Small external lags and tall diagrams favor early recovery. Implications for future research are discussed.

Moore, F. K.↗
NASA NTRS2014

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size On the Tip Clearance Flow Structure at Near Stall Operation - Part 2

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

Unsteady↗
NASA NTRS2017

Impact of Wake Dispersion on Axial Compressor Performance

Rotor wake dispersion in a low-speed, one and half stage axial compressor is investigated in detail with a Large Eddy Simulation (LES). The primary focus is to quantify the total pressure recovery due to wake stretching and the total pressure loss from the rotor wake interaction with the stator blade boundary layer. The relative magnitude of the aerodynamic loss due to these two effects is examined at several radial locations. The spacing between the rotor and the stator was varied from 29% to 112% of the rotor axial chord at the mid span to investigate the effects of rotor wake decay before entering the stator passage. The current analysis indicates that the efficiency through the compressor stage is increased about 0.5% when the spacing between the rotor and the stator is decreased from 112% to 29% of the rotor axial chord at mid-span. 22% of the efficiency gain from the narrower axial gap is due to the wake recovery and 63% is due to the stronger unsteady pressure field at the exit of the rotor due to stage interaction. Total pressure loss/recovery across the stator varies significantly in the radial direction for the current compressor, which has a much lower aspect ratio. The total pressure recovery due to wake stretching is larger than the total pressure loss due to the unsteady boundary layer development on the stator blade from 20% to 35% of the span from the hub for 29% spacing and from 35% to 55% of the span for 112% spacing. Above 50% of the span, rotor tip clearance flow affects wake dispersion and the overall wake recovery is less than expected.

Axial Compressor↗
NASA NTRS2003

A Compliant Casing for Transonic Axial Compressors

A viewgraph presentation on the concept of compliant casing for transonic axial compressors is shown. The topics include: 1) Concept for compliant casing; 2) Rig and facility details; 3) Experimental results; and 4) Numerical results.

Bloch, Gregory S.↗
NASA NTRS1983

A theory of rotating stall of multistage axial compressors. II - Finite disturbances

A small-disturbance theory of rotating stall in axial compressors is extended to finite amplitude, assuming the compressor characteristic is a parabola over the range of the disturbance. An exact solution is found which requires the operating point to be at the minimum or maximum of the parabola. If the characteristic is flat in a deep-stall regime, the previous harmonic solution applies with neither reverse flow or 'unstalling'. If the characteristic is concave upward in deep stall, the disturbance has a skewed shape, steeper at the stall-zone trailing edge as experiment shows. Propagation speed is only slightly affected by this nonlinearity. Near stall inception, negative curvature in combination with multiple stall zones can limit the nonlinear oscillation, in the manner of 'progressive' stall. If, as seems likely, lag at stall inception is negative (opposite to inertia), propagation speed exceeds 1/2 wheel speed, as experiments suggest.

Moore, F. K.↗
NASA NTRS2008

Application of Synthetic Jets to Reduce Stator Flow Separation in a Low Speed Axial Compressor

Flow control using synthetic jet injection has been applied in a low speed axial compressor. The synthetic jets were applied from the suction surface of a stator vane via a span-wise row of slots pitched in the streamwise direction. Actuation was provided externally from acoustic drivers coupled to the vane tip via flexible tubing. The acoustic resonance characteristics of the system, and the resultant jet velocities were obtained. The effects on the separated flow field for various jet velocities and frequencies were explored. Total pressure loss reductions across the vane passage were measured. The effect of synthetic jet injection was shown to be comparable to that of pulsatory injection with mass addition for stator vanes which had separated flow. While only a weak dependence of the beneficial effect was noted based on the excitation frequency, a strong dependence on the amplitude was observed at all frequencies.

Braunscheidel, Edward P.↗
NASA NTRS2003

Mechanisms of Rotating Instability in Axial Compressors Investigated

Rotating instability is a phenomenon that occurs in the tip flow region of axial compressor stages during stable operation. It can be observed in highly staggered rotors with significant tip clearance and is strongest at high-load operating points where the characteristic levels off. In this condition, the single-stage fan under investigation radiates an audible, whistling tone, and wall pressure spectra in the vicinity of the rotor disk exhibit nonrotational components. The graph shows the spectrum of static pressure at a point on the endwall near the leading edge. A hump appears at roughly half of the blade passing frequency (BPF) and is characteristic of rotating instability. A computational model was developed at the NASA Glenn Research Center to investigate the mechanism behind this phenomenon. A three-dimensional steady Navier-Stokes code that has been successfully tested for a wide range of turbomachinery flows was modified to execute a time-accurate simulation of the full annulus of the compressor. At the inlet of the computational domain, the total pressure, total temperature, and two velocity components are specified. Since no unsteady measurements of static pressure or other flow variables were available downstream of the rotor, circumferentially averaged static pressure was specified on the shroud at the outlet of the computational domain. A three-dimensional view of the vortex from the numerical model is shown. Particle traces released near the leading edge tip have rolled up to illustrate the tip clearance vortex. Flow near the trailing edge is pushed forward by the axially reversed flow. It then interacts with the tip clearance flow and the incoming flow and results in the rotating instability vortex, the core of which is illustrated by total pressure shading on planes located successively downstream. The rotating instability vortex is formed periodically midway between the blades and moves toward the pressure side of the passage. The unsteady behavior of this vortex structure is the main mechanism of the rotating instability is shown. The numerical model can be used to detect any possible occurrence of rotating instability when the tip clearance increases during engine service.

Hah, Chunill↗
NASA NTRS2018

Orifice Mass Flow Calculation in NASA's W-8 Single Stage Axial Compressor Facility

Updates to the orifice mass flow calculation for the W-8 Single Stage Axial Compressor Facility at NASA Glenn Research Center are provided to include the effect of humidity and incorporate ISO 5167. A methodology for including the effect of humidity into the inlet orifice mass flow calculation is provided. Orifice mass flow calculations provided by ASME PTC-19.5-2004, ASME MFC-3M-2004, ASME Fluid Meters, and ISO 5167 are compared for W-8's atmospheric inlet orifice plate. Differences in expansion factor and discharge coefficient given by these standards give a variation of about +/- 75% mass flow except for a few cases. A comparison of the calculations with an inlet static pressure mass flow correlation and a fan exit mass flow integration using test data from a 2017 turbofan rotor test in W-8 show good agreement between the inlet static pressure mass flow correlation, ISO 5167, and ASME Fluid Meters. While W-8's atmospheric inlet orifice plate violates the pipe diameter limit defined by each of the standards, the ISO 5167 is chosen to be the primary orifice mass flow calculation to use in the W-8 facility.

Aerodynamics↗
NASA NTRS1995

Experimental and Computational Investigation of the Tip Clearance Flow in a Transonic Axial Compressor Rotor

Experimental and computational techniques are used to investigate tip clearance flows in a transonic axial compressor rotor at design and part speed conditions. Laser anemometer data acquired in the endwall region are presented for operating conditions near peak efficiency and near stall at 100% design speed and at near peak efficiency at 60% design speed. The role of the passage shock/leakage vortex interaction in generating endwall blockage is discussed. As a result of the shock/vortex interaction at design speed, the radial influence of the tip clearance flow extends to 20 times the physical tip clearance height. At part speed, in the absence of the shock, the radial extent is only 5 times the tip clearance height. Both measurements and analysis indicate that under part-speed operating conditions a second vortex, which does not originate from the tip leakage flow, forms in the endwall region within the blade passage and exits the passage near midpitch. Mixing of the leakage vortex with primary flow downstream of the rotor at both design and part speed conditions is also discussed.

Suder, Kenneth L.↗
NASA NTRS1974

Three-dimensional flow in transonic axial compressor blade rows

Recent developments in the three-dimensional aerodynamic theory of inviscid flow in transonic axial compressors are reviewed. Emphasis is placed on the newly completed lifting surface theory of a transonic ducted rotor. The relationship between the lifting surface theory and axisymmetric through-theories of turbomachines is illustrated; a few examples of the additional information obtainable from the new theory are then given. Quasi-two-dimensional cascade theory can also be extracted from the present analysis and the relevance of cascade theory to the actual three-dimensional problem assessed. Details are reported elsewhere, but some of the qualitative conclusions are discussed here. Even moderate departure from uniform spanwise loading of the rotor blades, for example, leads to a rather profound influence of the downstream wakes, suggesting the need for considerable care in applying cascade data on a direct quasi-two-dimensional basis.

Mccune, J. E.↗