Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Anodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electroanalytical Exploration of Li Loss at the Solid Electrolyte-Anode Interface in Anode-Free Batteries with Polymer Electrolytes

Li loss during cycling at the solid electrolyte|anode interface strongly determines the cycle life of anode-free solid-state batteries (SSBs). Here, this loss is probed electroanalytically for polymer electrolyte (PE)-based SSBs in anode-free coin cells with practical pressures. A wide range of parameters expected to impact the measured average coulombic efficiency (CE) were explored to estimate the expected range of performance. These factors include PE type, cycling profiles, current collector type, and the presence of a thin Li seed layer. Further, low CE values in the ~50%–85% range are observed for all electrolytes and test conditions. Other than the electrolyte type, a strong dependence of the CE on the electrochemical cycling profile and the type of metallic current collector is observed. Compared to the anode-free setup, the presence of a thin (5 μ m) Li seed layer did not improve the average CE for two out of three PEs, suggesting its presence to be a weak contributor in minimizing the Li loss. This work provides baseline data on the Li losses in low-pressure anode-free configuration cells with PEs.

25 ENERGY STORAGE↗
DOE OSTI2020

Enabling 6C Fast Charging of Li–Ion Batteries with Graphite/Hard Carbon Hybrid Anodes

Li-ion batteries that can simultaneously achieve high-energy density and fast charging are essential for electric vehicles. Graphite anodes enable a high-energy density, but suffer from an inhomogeneous reaction current and irreversible Li plating during fast charging. In contrast, hard carbon exhibits superior rate performance but lower energy density owing to its lower initial coulombic efficiency and higher average voltage. In this work, these tradeoffs are overcome by fabricating hybrid anodes with uniform mixtures of graphite and hard carbon, using industrially-relevant multi-layer pouch cells (>1 Ah) and electrode loadings (3 mAh cm –2 ). By controlling the graphite/hard carbon ratio, this study shows that battery performance can be systematically tuned to achieve both high-energy density and efficient fast charging. Pouch cells with optimized hybrid anodes retain 87% and 82% of their initial specific energy after 500 cycles of 4C and 6C fast-charge cycling, respectively. This is significantly higher than the 61% and 48% specific energy retention with graphite anodes under the same conditions. The enhanced performance is attributed to improved homogeneity of the reaction current throughout the hybrid anode, which is supported by continuum-scale modeling. Furthermore, this process is directly compatible with existing roll-to-roll battery manufacturing, representing a scalable pathway to fast charging.

25 ENERGY STORAGE↗
DOE OSTI2021

UiO-66 Metal–Organic Framework as an Anode for a Potassium-Ion Battery: Quantum Mechanical Analysis

The natural abundance of potassium in the earth’s crust is 1000 times higher than that of lithium, so energy technologies built on potassium are more sustainable. Potassium-ion batteries have attracted considerable attention because of their relatively low cost and high operating potential, but questions remain about the best anode material for such batteries. Here, in this paper, we report first-principles computations based on density functional theory to investigate the performance of the UiO-66 metal–organic framework as an anode material for potassium-ion batteries; the goal is to provide a fundamental understanding of metal–organic framework (MOF)-based electrodes to guide the design and development of high-performance potassium-ion batteries. Our study includes the stability and electronic properties of potassiated structures and the mechanisms of potassium intercalation and diffusion in the framework. The results indicate that UiO-66 has a maximum specific capacity of 644 mAh/g as the anode of a potassium-ion battery. During potassiation, we observe charge transfer from potassium to carbon or oxygen of UiO-66 near the intercalated K. During K diffusion, the K migrates along the UiO-66 framework with a maximal migration energy barrier of 0.377 eV in the optimal pathway, which is much lower than the barriers for Li and Na diffusion in UiO-66. The diffusion coefficient of K in the anode is several orders of magnitude larger than those of Li and Na. This favors potassium ions over lithium ions or sodium ions when UiO-66 is the anode.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Surprising Relationship between Silicon Anode Calendar Aging and Electrolyte Components in a Localized High-Concentration Electrolyte System

Although localized high-concentration electrolytes (LHCEs) have been shown to improve the calendar lifetime of silicon anodes, the roles of the electrolyte constituents in calendar aging are not well understood. Here, in this work, we utilize a voltage hold protocol and an LHCE with varying molar ratios of lithium bis(fluorosulfonyl)imide (LiFSI), tetramethylene sulfone (TMS), and 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropyl ether (TTE) to probe the component roles during aging. Interestingly, the estimated calendar lifetime and irreversible lithium losses from the V-hold experiments are independent of the electrolyte formulations. Contrarily, the solid electrolyte interphase (SEI) composition depends on the electrolyte formulation. X-ray photoelectron spectroscopy shows that TMS-coordinated species decompose to form insoluble alkanes and lithium hydroxide (LiOH), while lithium fluoride (LiF) originates from the anion-coordination complex. The SEI composition does not appear to play a significant role in the silicon anode passivity, as measured by parasitic current, suggesting that the SEI-electrolyte interactions dictate the calendar aging mechanisms.

Si anode↗
DOE OSTI2021

Crossover Effects in Batteries with High–Nickel Cathodes and Lithium–Metal Anodes

It is well understood that cathode-to-anode crossover, especially of transition-metal ions, can significantly impact the long-term cycling of lithium-ion batteries. The dissolved transition-metal ions in lithium-ion cells deposit on the graphite anode, disrupt the solid-electrolyte interphase (SEI), and catalyze further side reactions. Meanwhile, crossover effects in lithium-metal batteries have rarely been studied. This study is the first to investigate crossover effects in lithium-metal batteries with high-nickel layered-oxide cathodes. It is shown that the crossover of transition-metal ions from LiNi 0.9 Mn 0.05 Co 0.05 O 2 has minimal effect on the lithium-metal anode (LMA) due to the following reasons. The catalytic transition metals 1) have less effect on an inherently reactive LMA, 2) are diluted in a thicker SEI, and 3) are produced in overall lower quantity due to the limited cycle life of the LMA. Conversely, the LMA generates soluble decomposition products that cross over to the cathode even during early cycling. This crossover accelerates impedance growth and capacity fade at the cathode and is partially responsible for the mismatch between the performance of half and full-cells with layered-oxide cathodes. Finally, this study highlights the need for better battery design with LMA, potentially including electrolyte or cell modifications.

25 ENERGY STORAGE↗
DOE OSTI2021

Parametric analysis of anodic degradation mechanisms for fast charging lithium batteries with graphite anode

In this work, we report the impact of the temperature-driven synergistically-coupled anodic degradation mechanisms on the electrochemical performance of lithium batteries with graphite anode over multiple cycles. Temperature dependence of electrochemical reactions and damage mechanisms, such as solid electrolyte interface (SEI) growth, lithium plating/stripping, dead lithium storage/dissolution, and film cracking are incorporated into the degradation model. Results of a parametric analysis are presented, evaluating the effects of charging rates (1–6 C), operating temperatures (-15 – 45°C) and electrode design parameters, on the relative performance fade in the lithium-ion battery. Thermo-electrochemical process maps are developed to provide insights into the relationship between electrode performance and failure mechanisms. The simulation results predict a severe capacity loss due to lithium plating at low temperatures, which is further aggravated at high charging rates. A common strategy for mitigating lithium plating, through charging at high temperatures, also results in rapid capacity loss due to accelerated SEI formation. Simulation results are used to identify the combination of operating conditions and electrode design parameters that improve the electrochemical performance of the battery. These results demonstrate an opportunity to design safe and high-performance lithium-ion batteries, guided by anodic degradation models.

Battery design↗
NASA NTRS1995

Thin-film sulfuric acid anodizing as a replacement for chromic acid anodizing

Chromic acid has long been used to produce a thin, corrosion resistant (Type I) coating on aluminum. Following anodizing, the hardware was sealed using a sodium dichromate solution. Sealing closes up pores inherent in the anodized coating, thus improving corrosion resistance. The thinness of the brittle coating is desirable from a fatigue standpoint, and chromium was absorbed by the coating during the sealing process, further improving corrosion resistance. Unfortunately, both chromic acid and sodium dichromate contain carcinogenic hexavalent chromium. Sulfuric acid is being considered as a replacement for chromic acid. Sulfuric acid of 10-20 percent concentration has traditionally been used to produce relatively thick (Types II and III) or abrasion resistant (Type III) coatings. A more dilute, that is five weight percent, sulfuric acid anodizing process, which produces a thinner coating than Type II or III, with nickel acetate as the sealant has been developed. The process was evaluated in regard to corrosion resistance, throwing power, fatigue life, and processing variable sensitivity, and shows promise as a replacement for the chromic acid process.

Kallenborn, K. J.↗
DOE OSTI2022

Three-dimensional architectured anode, a direct carbon fuel cell including the three-dimensional architectured anode, and related methods

A method of fabricating a three-dimensional (3D) architectured anode. The method comprises immersing a fabric textile in a precursor solution, the precursor solution comprising a nickel salt and gadolinium doped ceria (GDC). The nickel salt and GDC are absorbed to the fabric textile. The fabric textile comprising the absorbed nickel salt and GDC is removed from the precursor solution and calcined to form a 3D architectured anode comprising nickel oxide and GDC. Additional methods and a direct carbon fuel cell including the 3D architectured anode are also disclosed.

Ding, Dong↗
DOE OSTI2022

Fast and Simple Ag/Cu Ion Exchange on Cu Foil for Anode-Free Lithium-Metal Batteries

Lithium-metal batteries with zero excess lithium on the anode side paired with a fully lithiated cathode are regarded as a form of the highest energy-density configuration. Unfortunately, the continuous lithium loss over cycling from a limited amount of lithium reservoir significantly degrades the overall cell performance in the anode-free system. To mitigate the deterioration, modifying the current collector for enhanced lithium cycling is an indispensable route. Here, we apply a Ag/Cu ion exchange to precipitate micro-sized Ag particles on the Cu current collector to enhance the lithium reversibility via (de)alloying process. Further, we show a smoother morphology of lithium upon alloying, which leads to a lowered nucleation potential as well as increased average Coulombic efficiency in Li||Cu cells regardless of electrolyte formulation. The preferred lithium adsorption on Ag and AgLi over Cu is demonstrated with density functional theory calculations, which supports that Li is forming a gamma-phase alloy in the last stage rather than being deposited beneath the alloy. Lastly, this simple Cu foil modification enhances lithium reversibility and reduces its nucleation barrier, thus mitigating the capacity fade of a Cu||LiFePO 4 with reduced polarization.

25 ENERGY STORAGE↗