SEARCH · Engineering Papers

Results for “Alloy Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1997

Design for Oxidation Resistance

Alloys intended for use in high-temperature environment rely on the formation of a continuous, compact, slow-growing oxide layer for oxidation and hot corrosion resistance. To be protective, this oxide layer must be chemically, thermodynamically stable. Successful alloy design for oxidative environment is best achieved by developing alloys that are capable of forming adherent scales of either alumina (Al2O3), chromia (Cr2O3), or silica (SiO2). In this article, emphasis has been placed on the issue related to high-temperature oxidation of superalloys used in gas turbine engine application. Despite the complexity of these alloys, optimal performance has been associated with protective alumina scale formation. As will be described below, both compositional makeup and protective coatings play key role in providing oxidation protection. Other high-temperature materials described include nickel and titanium aluminide intermetallics, refractory metal, and ceramics.

Smialek, James L.↗

NASA NTRS2002

Experimental Verification of the Theoretical Prediction of the Phase Structure of a Ni-Al-Ti-Cr-Cu Alloy

The Bozzolo-Ferrante-Smith (BFS) method for alloys was applied to the study of NiAl-based materials to assess the effect of alloying additions on structure. Ternary, quaternary and even pentalloys based on NiAl with additions of Ti, Cr and Cu were studied and experimental verification of the theoretical predictions including the phase structure of a Ni-Al-Ti-Cr-Cu alloy is presented. Two approaches were used, Monte Carlo simulations to determine low energy structures, and analytical calculations of the energy of high symmetry configurations which give physical insight into preferred structures. The energetics for site occupancy in ternary and quaternary systems were calculated leading to an indirect determination of solubility limits at 0 K. Precipitate formation with information concerning structure and lattice parameter were also 'observed' computationally and the general characteristics of a Ni-Al-Ti-Cr-Cu alloy were correctly predicted. The results indicate that the BFS method for alloys can be a useful tool for alloy design and can be used to complement experimental alloy design programs.

Wilson, A.↗

NASA NTRS1997

Progress in the Modeling of NiAl-Based Alloys Using the BFS Method

The BFS method has been applied to the study of NiAl-based materials to assess the effect of alloying additions on structure. Ternary, quaternary and even pent-alloys based on Ni-rich NiAl with additions of Ti, Cr and Cu were studied. Two approaches were used, Monte Carlo simulations to determine ground state structures and analytical calculations of high symmetry configurations which give physical insight into preferred bonding. Site occupancy energetics for ternary and the more complicated case of quaternary additions were determined, and solubility limits and precipitate formation with corresponding information concerning structure and lattice parameter were also 'observed' computationally. The method was also applied to determine the composition of alloy surfaces and interfaces. Overall, the results demonstrate that the BFS method for alloys is a powerful tool for alloy design and with its simplicity and obvious advantages can be used to complement any experimental alloy design program.

Bozzolo, Guillermo↗

NASA NTRS1998

An Introduction to the BFS Method and Its Use to Model Binary NiAl Alloys

We introduce the Bozzolo-Ferrante-Smith (BFS) method for alloys as a computationally efficient tool for aiding in the process of alloy design. An intuitive description of the BFS method is provided, followed by a formal discussion of its implementation. The method is applied to the study of the defect structure of NiAl binary alloys. The groundwork is laid for a detailed progression to higher order NiAl-based alloys linking theoretical calculations and computer simulations based on the BFS method and experimental work validating each step of the alloy design process.

Bozzolo, Guillermo↗

NASA NTRS2010

A New Approach of Designing Superalloys for Low Density

New low-density single-crystal (LDS) alloy, have bee. developed for turbine blade applications, which have the potential for significant improvements in the thrust-to-weight ratio over current production superalloys. An innovative alloying strategy was wed to achieve alloy density reductions, high-temperature creep resistance, microstructural stability, and cyclic oxidation resistance. The alloy design relies on molybdenum as a potent. lower-density solid-solution strengthener in the nickel-based superalloy. Low alloy density was also achieved with modest rhenium levels tmd the absence of tungsten. Microstructural, physical mechanical, and environmental testing demonstrated the feasibility of this new LDS superalloy design.

MacKay, Rebecca A.↗

NASA NTRS2007

Preliminary Structural Sizing and Alternative Material Trade Study of CEV Crew Module

This paper presents the results of a preliminary structural sizing and alternate material trade study for NASA s Crew Exploration Vehicle (CEV) Crew Module (CM). This critical CEV component will house the astronauts during ascent, docking with the International Space Station, reentry, and landing. The alternate material design study considers three materials beyond the standard metallic (aluminum alloy) design that resulted from an earlier NASA Smart Buyer Team analysis. These materials are graphite/epoxy composite laminates, discontinuously reinforced SiC/Al (DRA) composites, and a novel integrated panel material/concept known as WebCore. Using the HyperSizer (Collier Research and Development Corporation) structural sizing software and NASTRAN finite element analysis code, a comparison is made among these materials for the three composite CM concepts considered by the 2006 NASA Engineering and Safety Center Composite Crew Module project.

Bednarcyk, Brett A.↗

NASA NTRS1984

Effects of alloy composition on cyclic flame hot-corrosion attack of cast nickel-base superalloys at 900 deg C

The effects of Cr, Al, Ti, Mo, Ta, Nb, and W content on the hot corrosion of nickel base alloys were investigated. The alloys were tested in a Mach 0.3 flame with 0.5 ppmw sodium at a temperature of 900 C. One nondestructive and three destructive tests were conducted. The best corrosion resistance was achieved when the Cr content was 12 wt %. However, some lower-Cr-content alloys ( 10 wt%) exhibited reasonable resistance provided that the Al content alloys ( 10 wt %) exhibited reasonable resistance provided that the Al content was 2.5 wt % and the Ti content was Aa wt %. The effect of W, Ta, Mo, and Nb contents on the hot-corrosion resistance varied depending on the Al and Ti contents. Several commercial alloy compositions were also tested and the corrosion attack was measured. Predicted attack was calculated for these alloys from derived regression equations and was in reasonable agreement with that experimentally measured. The regression equations were derived from measurements made on alloys in a one-quarter replicate of a 2(7) statistical design alloy composition experiment. These regression equations represent a simple linear model and are only a very preliminary analysis of the data needed to provide insights into the experimental method.

Deadmore, D. L.↗

NASA NTRS1985

Cast iron-base alloy for cylinder/regenerator housing

NASACC-1 is a castable iron-base alloy designed to replace the costly and strategic cobalt-base X-40 alloy used in the automotive Stirling engine cylinder/generator housing. Over 40 alloy compositions were evaluated using investment cast test bars for stress-rupture testing. Also, hydrogen compatibility and oxygen corrosion resistance tests were used to determine the optimal alloy. NASACC-1 alloy was characterized using elevated and room temperature tensile, creep-rupture, low cycle fatigue, heat capacity, specific heat, and thermal expansion testing. Furthermore, phase analysis was performed on samples with several heat treated conditions. The properties are very encouraging. NASACC-1 alloy shows stress-rupture and low cycle fatigue properties equivalent to X-40. The oxidation resistance surpassed the program goal while maintaining acceptable resistance to hydrogen exposure. The welding, brazing, and casting characteristics are excellent. Finally, the cost of NASACC-1 is significantly lower than that of X-40.

Witter, Stewart L.↗

NASA NTRS1991

Evaluation of the microstructure of Al-Cu-Li-Ag-Mg Weldalite (tm) alloys, part 4

Weldalite (trademark) 049 is an Al-Cu-Li-Ag-Mg alloy designed to have ultrahigh strength and to serve in aerospace applications. The alloy displays significantly higher strength than competitive alloys in both naturally aged and artificially aged tempers. The strengthening phases in such tempers have been identified to, in part, explain the mechanical properties attained. In general, the alloy is strengthened by delta prime Al3Li and Guinier-Preston (GP) zones in the naturally aged tempers. In artificially aged tempers in slightly underaged conditions, strengthening is provided by several phases including GP zones, theta prime Al2Cu, S prime Al2CuMg, T(sub 1) Al2CuLi, and possibly a new phase. In the peak strength artificially aged tempers, T(sub 1) is the predominant strengthening phase.

Pickens, Joseph R.↗

NASA NTRS1989

Identification of a cast iron alloy containing nonstrategic elements

A program was performed to address the mechanical and environmental needs of Stirling engine heater head and regenerator housing components, while reducing the dependence on strategic materials. An alloy was developed which contained no strategic elemental additions per se. The base is iron with additions of manganese, molybdenum, carbon, silicon, niobium, and ferro-chromium. Such an alloy should be producible on a large scale at very low cost. The resulting alloy, designated as NASAUT 4G-Al, contained 15 Mn, 15 Cr, 2 Mo, 1.5 C, 1.0 Si, 1.0 Nb (in weight percent) with a balance of Fe. This alloy was optimized for chemistry, based upon tensile strength, creep-rupture strength, fracture behavior, and fatigue resistance up to 800 C. Alloys were also tested for environmental compatibility. The microstructure and mechanic properties (including hardness) were assessed in the as-cast condition and following several heat treatments, including one designed to simulate a required braze cycle. The alloy was fabricated and characterized in the form of both equiaxed and columnar-grained castings. The columnar grains were produced by directional solidification, and the properties were characterized in both the longitudinal and transverse orientations. The NASAUT 4G-Al alloy was found to be good in cyclic-oxidation resistance and excellent in both hydrogen and hot-corrosion resistance, especially in comparison to the baseline XF-818 alloy. The mechanical properties of yield strength, stress-rupture life, high-cycle-fatigue resistance, and low-cycle-fatigue resistance were good to excellent in comparison to the current alloy for this application, HS-31 (X-40), with precise results depending in a complex manner on grain orientation and temperature. If required, the ductility could be improved by lowering the carbon content.

Cooper, C. V.↗

NASA NTRS1987

High-temperature ordered intermetallic alloys II; Proceedings of the Second Symposium, Boston, MA, Dec. 2-4, 1986

The papers presented in this volume provide on overview of recent theoretical and experimental research in the field of high-temperature ordered intermetallic alloys. The papers are gouped under the following headings: ordering behavior and theory, microstructures, mechanical behavior, alloy design and microstructural control, and metallurgical properties. Specific topics discussed include antiphase domains, disordered films and the ductility of ordered alloys based on Ni3Al; kinetics and mechanics of formation of Al-Ni intermetallics; deformability improvements of L1(2)-type intermetallic compounds; B2 aluminides for high-temperature applications; and rapidly solidified binary TiAl alloys.

Stoloff, N. S.↗

NASA NTRS1975

Modified ferritic iron alloys with improved high-temperature mechanical properties and oxidation resistance

An alloy modification program was conducted in which the compositions of two existing Fe-Cr-Al alloys (Armco 18SR and GE-1541) were changed to achieve either improved high-temperature strength or improved fabricability. Only modifications of Armco 18SR were successful in achieving increased strength without loss of fabricability or oxidation resistance. The best modified alloy, designated NASA-18T, had twice the rupture strength of Armco 18SR at 800 and 1000 C. The NASA-18T alloy also had better oxidation resistance than Armco 18SR and comparable fabricability. The nominal composition of NASA-18T is Fe-18Cr-2Al-1Si-1.25Ta. All attempted modifications of the GE-1541 alloy were unsuccessful in terms of achieving better fabricability without sacrificing high-temperature strength and oxidation resistance.

Oldrieve, R. E.↗

NASA NTRS2020

Producing Next Generation Superalloys Through Advanced Characterization and Manufacturing Techniques

NASA is currently working towards developing the next generation high temperature alloys for various aerospace and energy applications. Through advanced microscopy and computational insights, a novel atomic scale strengthening mechanism was discovered in Ni-base superalloys. This new local phase transformation strengthening technique has been successfully implemented resulting in new disk alloys with substantial improvements in creep strength over current state-of-the-art. Furthermore, additive manufacturing has been leveraged to produce dispersion strengthened (DS), multi-principal element alloys (MPEA) without the use of traditional mechanical alloying or chemical reactions. This new processing technique has successfully resulted in 99.9% dense oxide dispersion strengthened NiCoCr alloy parts. High temperature mechanical testing of the DS alloys showed significant improvements in strength and ductility over the baseline NiCoCr. As a result, this recently discovered processing route opens a new alloy design and production path that is synergistic between additive manufacturing and dispersion strengthening, possibly enabling a new generation of high-performance alloys.

Smith, Timothy M.↗

NASA NTRS2020

Efficient production of a high-performance dispersion strengthened, multi-principal element alloy

Additive manufacturing currently facilitates new avenues for materials discovery that have not been fully explored. In this study we reveal how additive manufacturing can be leveraged to produce dispersion strengthened (DS), multi-principal element alloys (MPEA) without the use of traditional mechanical alloying or chemical reactions. This new processing technique employed resonant acoustic mixing to coat an equiatomic NiCoCr powder with nano-scale yttrium oxides. Then, through laser powder bed fusion (L-PBF), the coated powder was successfully consolidated into 99.9% dense parts. Microstructural analysis confirmed the successful incorporation and dispersion of nano-scale oxides throughout the build volume. Furthermore, high temperature mechanical testing of the DS alloys showed significant improvements in strength and ductility over the baseline NiCoCr. As a result, this recently discovered processing route opens a new alloy design and production path that is synergistic between additive manufacturing and dispersion strengthening, possibly enabling a new generation of high-performance alloys.

T.M. Smith↗

NASA NTRSDate not supplied

GRX-810: NASA High Temperature Alloy Development for Additive Manufacturing

High-entropy alloys, and by extension, medium entropy alloys are an exciting new class of materials due to their impressive mechanical properties, especially at cryogenic and elevated temperatures. In this study, a novel oxide dispersion strengthened (ODS) NiCoCr-based alloy is presented which exhibits exceptional high temperature properties compared to conventional wrought superalloys. This new ODS alloy, GRX-810, leverages additive manufacturing to disperse nanoscale Y2O3 particles throughout the microstructure without the use of resource intensive processing steps, such as mechanical alloying. Microstructural and mechanical characterization confirms the successful incorporation and dispersion of nano-scale oxides throughout the build volume. As a result, this recently discovered processing route presents a new alloy design and production path that is synergistic between additive manufacturing and dispersion strengthening, possibly enabling a new generation of high-performance alloys.

Tim Smith↗

NASA NTRS2007

Development of GRCop-84 for Rocket Engine Applications

GRCop-84 (Cu-8 at.% Cr-4 at.% Nb) has been under development at the NASA Glenn Research Center for several years. The alloy possesses a unique combination of good thermal conductivity, high elevated temperature strength, long creep lives and long low cycle fatigue lives. The alloy is also more oxidation resistant than pure copper and most competitive alloys. The combination of properties has attracted attention from major rocket engine manufacturers who are interested in the alloy for the combustion chamber liner in their next generation of regeneratively cooled engines. It is also a strong candidate for various components in hypersonic vehicles, which also experience very high heat flux conditions. This presentation will discuss the alloy design strategies used to develop GRCop-84 and the various processing routes available for manufacturing components. The microstructure and mechanical properties of the alloy will be reviewed, as well as the results of actual hot fire testing of subscale rocket combustion chambers. The use of environmental and thermal barrier coatings to extend the performance to even higher levels will also be discussed.

Ellis, David L.↗

NASA NTRS2008

Microstructure Modeling of 3rd Generation Disk Alloy

The objective of this initiative, funded by NASA's Aviation Safety Program, is to model, validate, and predict, with high fidelity, the microstructural evolution of third-generation high-refractory Ni-based disc superalloys during heat treating and service conditions. This initiative is a natural extension of the DARPA-AIM (Accelerated Insertion of Materials) initiative with GE/Pratt-Whitney and with other process simulation tools. Strong collaboration with the NASA Glenn Research Center (GRC) is a key component of this initiative and the focus of this program is on industrially relevant disk alloys and heat treatment processes identified by GRC. Employing QuesTek s Computational Materials Dynamics technology and PrecipiCalc precipitation simulator, physics-based models are being used to achieve high predictive accuracy and precision. Combining these models with experimental data and probabilistic analysis, "virtual alloy design" can be performed. The predicted microstructures can be optimized to promote desirable features and concurrently eliminate nondesirable phases that can limit the reliability and durability of the alloys. The well-calibrated and well-integrated software tools that are being applied under the proposed program will help gas turbine disk alloy manufacturers, processing facilities, and NASA, to efficiently and effectively improve the performance of current and future disk materials.

Jou, Herng-Jeng↗

NASA NTRS1976

Basic aspects of superalloy design for crack growth resistance

It is pointed out that the major difficulty concerning an understanding of the flaw growth resistance properties of superalloys is related to the lack of basic theories. An attempt is made to develop these theories, taking into account their use for the identification of tentative alloy design guidelines for flaw growth resistance. A brief review of the fatigue crack growth literature is provided. Attention is given to continuous fatigue crack growth theory, threshold fatigue crack growth, planar slip superalloy fatigue crack growth, and aspects of creep crack growth resistance.

Tien, J. K.↗