SEARCH · Engineering Papers
Results for “AlFe”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Multifunctional Separator Allows Stable Cycling of Potassium Metal Anodes and of Potassium Metal Batteries
Here, this is the first report of a multifunctional separator for potassium-metal batteries (KMBs). Here, double-coated tape-cast microscale AlF 3 on polypropylene (AlF 3 @PP) yields state-of-the-art electrochemical performance: symmetric cells are stable after 1000 cycles (2000 h) at 0.5 mA cm –2 and 0.5 mAh cm –2 , with 0.042 V overpotential. Stability is maintained at 5.0 mA cm –2 for 600 cycles (240 h), with 0.138 V overpotential. Postcycled plated surface is dendrite-free, while stripped surface contains smooth solid electrolyte interphase (SEI). Conventional PP cells fail rapidly, with dendrites at plating, and “dead metal” and SEI clumps at stripping. Potassium hexacyanoferrate(III) cathode KMBs with AlF 3 @PP display enhanced capacity retention (91% at 100 cycles vs 58%). AlF 3 partially reacts with K to form an artificial SEI containing KF, AlF 3 , and Al 2 O 3 phases. The AlF 3 @PP promotes complete electrolyte wetting and enhances uptake, improves ion conductivity, and increases ion transference number. The higher of K + transference number is ascribed to the strong interaction between AlF 3 and FSI – anions, as revealed through 19 F NMR. The enhancement in wetting and performance is general, being demonstrated with ester- and ether-based solvents, with K-, Na-, or Li- salts, and with different commercial separators. In full batteries, AlF 3 prevents Fe crossover and cycling-induced cathode pulverization.
Stabilized Lithium, Manganese-Rich Layered Cathode Materials Enabled by Integrating Co-Doping and Nanocoating
While lithium, manganese-rich (LMR) layered oxide cathode materials offer high energy density (>900 Wh kg –1 ) and low cost, LMR is susceptible to continuous capacity and voltage decay from the oxygen migration and side reaction with aqueous electrolyte at high voltage. Herein, the integration of Na/F co-doping (CD) and AlF 3 coating on LMR is achieved without the need of complex atomic layer deposition. Akin to pristine and CD samples, CD with 1 wt % AlF 3 (CD-1.0 wt %) shows excellent electrochemical performance with the capacity and voltage retentions of 93 and 91% after 150 cycles at 0.5C, respectively, and increased ionic conductivity. Spectroscopic analysis indicates that the coating mainly influences the Co distribution, where Co is enriched on the surface, and partial diffusion of Al 3+ ions toward the bulk, leading to a slight change of transition-metal (TM) valence states at the nanometer scale and the formation of a stable Li x (CoAl)O y phase. Post-cycling analysis reveals that CD-1.0 wt % can alleviate the formation of rock-salt structure and Mn dissolution. Besides, little to no metal segregation is detected for the cycled CD-1.0 wt % sample. This finding presents the first instance to apply co-doping and AlF 3 coating as a new strategy to enhance the structural homogeneity and takes another step toward their commercial viability.
The reactivity of experimentally reduced lunar regolith simulants: Health implications for future crewed missions to the lunar surface
Crewed missions to the Moon may resume as early as 2026 with NASA's Artemis III mission, and lunar dust exposure/inhalation is a potentially serious health hazard that requires detailed study. Current dust exposure limits are based on Apollo-era samples that spent decades in long-term storage on Earth; their diminished reactivity may lead to underestimation of potential harm that could be caused by lunar dust exposure. In particular, lunar dust contains nanophase metallic iron grains, produced by “space weathering”; the reactivity of this unique component of lunar dust is not well understood. Herein, we employ a chemical reduction technique that exposes lunar simulants to heat and hydrogen gas to produce metallic iron particles on grain surfaces. We assess the capacity of these reduced lunar simulants to generate hydroxyl radical (OH*) when immersed in deionized (DI) water, simulated lung fluid (SLF), and artificial lysosomal fluid (ALF). Lunar simulant reduction produces surface-adhered metallic iron “blebs” that resemble nanophase metallic iron particles found in lunar dust grains. Reduced samples generate ~5–100× greater concentrations of the oxidative OH* in DI water versus non-reduced simulants, which we attribute to metallic iron. SLF and ALF appear to reduce measured OH*. The increase in observed OH* generation for reduced simulants implies high oxidative damage upon exposure to lunar dust. Low levels of OH* measured in SLF and ALF imply potential damage to proteins or quenching of OH* generation, respectively. Reduction of lunar dust simulants provides a quick cost-effective approach to study dusty materials analogous to authentic lunar dust.
Understanding formation mechanisms of intermetallic compounds in dissimilar Al/steel joint processed by resistance spot welding
Here, this paper confirmed the formation mechanism of intermetallic compounds (IMCs) in Al/steel resistance spot welds with transmission electron microscopy, electron backscatter diffraction, nanoindentation and thermodynamic calculations. In particular, the formation of AlFe with BCC_B2 structure, which is not commonly seen in welds, was identified. The formation mechanism of IMCs at the high welding energy region is described as follows. Al 13 Fe 4 first nucleates from the Al side, followed by Al 5 Fe 2 growth with Fe atoms accumulating at the Al 13 Fe 4 grain boundaries. Then, Al 5 Fe 2 grains grow continuously to coarse columnar grains, and AlFe forms at the interface of Al 5 Fe 2 grains and the ferrite phase. Lastly, the needle-like Al 13 Fe 4 forms in the cooling process. At the middle welding energy region, only equiaxed Al 5 Fe 2 and small Al 13 Fe 4 grains are formed at the interface because of the lower diffusion rates of Al and Fe, hence postponing the growth of Al 5 Fe 2 and Al 13 Fe 4 . At the low welding energy region, only sporadic Al 5 Fe 2 and Al 13 Fe 4 grains are formed surrounded by the Al phase.
F and N Rich Solid Electrolyte for Stable All-Solid-State Battery
We report the instability of sulfide solid electrolytes to Li anode and high-voltage LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathodes limits the cyclic performance of all-solid-state lithium battery (ASSLB). Herein, the stability of Li 6 PS 5 Cl against Li anode is enhanced by mixing a small amount (0.32 wt%) of CuF 2 -LiNO 3 (CL) into Li 6 PS 5 Cl electrolyte layer to in-situ form a mixed-conductive-lithiophobic and self-healing LiF-Li 3 N-Cu solid electrolyte interphase (SEI) at Li 6 PS 5 Cl-CL/Li interface. The critical current density (CCD) of Li 6 PS 5 Cl-CuF 2 -LiNO 3 increases to 1.4 mA cm –2 /1.4 mAh cm –2 at room temperature, which is much higher than that of pristine Li 6 PS 5 Cl (0.4 mA cm –2 /0.4 mAh cm –2 ) even though mixing 0.32 wt% CL into Li 6 PS 5 Cl slightly reduces the ionic conductivity from 2.9 × 10 –3 to 1.5 × 10 –3 S cm –1 . The compatibility of Li 6 PS 5 Cl-CL electrolyte to single-crystalline NMC811 (S-NMC811) is further enhanced by adding a small amount (0.02 wt%) of AlF 3 into Li 6 PS 5 Cl-CL forming Li 6 PS 5 Cl-CuF 2- LiNO 3 -AlF 3 (Li 6 >PS 5 Cl-CLA) as a cathode electrolyte and by doing Cl – on S-NMC811 (Cl@S-NMC811) surface. The Cl@S-NMC811-Li 6 PS 5 Cl-CLA|Li 6 PS 5 Cl-CL|Li cells with areal capacity of 2.55 mAh cm -2 achieve a capacity retention of 69.4% after 100 cycles at 1C (1C = 200 mAh g -1 ). Adding a small amount of SEI and cathode/electrolyte interphase (CEI) former into the sulfide electrolytes with minimal reduction (48.3%) of ionic conductivity is an effective method to enhance the performance of ASSLB.
Using numerical methods to screen magnetocaloric materials in an active magnetic regenerative cycle
A 2-dimensional numerical model of a room temperature operating Active Magnetic Regenerator (AMR) that comprises of a regenerator, hot and cold heat exchangers, heat transfer fluid is developed. The regenerator is made of a magnetocaloric material (MCM) which heats up upon applying a magnetic field, H, and cools down when the field is removed; thus, making it the most essential part of an AMR. The model takes experimentally measured ΔT ad (H,T) and the C p (H,T) data as input and provides quantitative performance metrics of the magnetic cooling system, such as ΔT span and the cooling load, as output. With this model, it is possible to assess a wide range of MCMs in an AMR. 4 different MCMs were investigated using this model in terms of their ΔT span and the cooling loads—LaFe 10.96 Co 0.97 Si 1.07 , MnFeP (1-x) As (x) and AlFe 2 B 2 and Gd. During the screening of MCMs, all the important operating conditions of the device were fixed such as the fluid flow rate, ambient temperature, cycle duration, magnetic field strength. Our results indicate that Gd exhibits the maximum ΔT span with respectable cooling load, while AlFe 2 B 2 generates the lowest ΔT span . Even though LaFeCoSi compound did not perform as well as Gd, it could be the MCM choice for the realization of magnetic refrigeration on a global scale due to its much lower cost.
Towards additive manufacturing of magnetocaloric working materials
The feasibility of three-dimensional printing via the Directed Energy Deposition (DED) technique is demonstrated for the ferromagnetic AlFe 2 B 2 (aka 1-2-2) compound, which shows promise as a working material for room-temperature magnetocaloric devices. Like many intermetallic materials, the 1-2-2 compound is brittle at room temperature; not only is it difficult to synthesize from the melt, it is challenging to form it into useful geometries necessary for effective heat transfer in magnetocaloric devices. Using Laser Engineered Net Shaping (LENS TM ) synthesis from two powder precursors, AlB 2 and Fe, samples of simple (rod) and complex (honeycomb) architectures were successfully synthesized. Furthermore, the phase constitution and distribution, magnetic transition temperature, and saturation magnetization determined for the LENS TM -synthesized rod sample are all similar to those obtained for 1-2-2 materials made by conventional casting. Further, the measured magnetic entropy change, as determined from Maxwell's Relations applied to magnetic data, indicates that the magnetocaloric response of the annealed LENS TM -printed rod samples are comparable to those of the 1-2-2 compounds made by conventional techniques. These results confirm that complex magnetofunctional shapes, which are needed for efficient energy conversion in magnetocaloric devices, can be rapidly fabricated from the AlFe 2 B 2 compound.
Forming mechanism of equilibrium and non-equilibrium metallurgical phases in dissimilar aluminum/steel (Al–Fe) joints
Abstract Forming metallurgical phases has a critical impact on the performance of dissimilar materials joints. Here, we shed light on the forming mechanism of equilibrium and non-equilibrium intermetallic compounds (IMCs) in dissimilar aluminum/steel joints with respect to processing history (e.g., the pressure and temperature profiles) and chemical composition, where the knowledge of free energy and atomic diffusion in the Al–Fe system was taken from first-principles phonon calculations and data available in the literature. We found that the metastable and ductile (judged by the presently predicted elastic constants) Al 6 Fe is a pressure ( P ) favored IMC observed in processes involving high pressures. The MoSi 2 -type Al 2 Fe is brittle and a strong P -favored IMC observed at high pressures. The stable, brittle η-Al 5 Fe 2 is the most observed IMC (followed by θ-Al 13 Fe 4 ) in almost all processes, such as fusion/solid-state welding and additive manufacturing (AM), since η-Al 5 Fe 2 is temperature-favored, possessing high thermodynamic driving force of formation and the fastest atomic diffusivity among all Al–Fe IMCs. Notably, the ductile AlFe 3 , the less ductile AlFe, and most of the other IMCs can be formed during AM, making AM a superior process to achieve desired IMCs in dissimilar materials. In addition, the unknown configurations of Al 2 Fe and Al 5 Fe 2 were also examined by machine learning based datamining together with first-principles verifications and structure predictions. All the IMCs that are not P- favored can be identified using the conventional equilibrium phase diagram and the Scheil-Gulliver non-equilibrium simulations.
Polymorphism in A 3 MF 6 (A = Rb, Cs; M = Al, Ga) grown using mixed halide fluxes
Single crystals of A 3 MF 6 (A = Rb, Cs; M = Al, Ga) were grown from mixed alkali chloride/fluoride fluxes in sealed silver tubes. For Cs 3 AlF 6 and Cs 3 GaF 6 , two polymorphs were observed at room temperature: m-Cs 3 MF 6 and o-Cs 3 MF 6 . For the two Rb containing compositions, only one room temperature polymorph was observed: o-Rb 3 AlF 6 and t-Rb 3 GaF 6 , respectively. Simultaneous TGA/DSC and high temperature SCXRD/PXRD were used to study the high temperature behavior of A 3 MF 6 . Here, the compounds of all four compositions were found to undergo structure transitions upon heating to the same cubic structure type, c-A 3 MF 6 .
Tritium Trapping Thermodynamics by Point Defects at Interfacial Fe-Al Phases of the Aluminide Coating
Density functional theory (DFT) simulations have been carried out to evaluate the potential for tritium trapping by metal vacancies in four phases (i.e., (Fe, Cr, Ni), AlFe 3 , NiAl, and AlFe) identified near the interface between the Al coating and 316 stainless steel (316 SS) cladding. In addition, an ab initio thermodynamics approach has been employed to predict the temperature and T 2 -partial pressure dependence on the thermodynamics of tritiated defects. Key results in this work suggest that metal vacancies in the four phases have the potential to favorably trap tritium species. This thermodynamic trend can be correlated to the high energy cost of having an interstitial tritium in the lattice, which has been calculated to be at least 0.48 eV. By combining the results of this study with previous theoretical works investigating tritium behavior in other Fe-Al phases identified in the aluminide coating, suggest that metal vacancies are generally able to trap tritium in various Fe-Al aluminide phases. Especially, it was found that Al vacancies are the most efficient to trap tritium, followed by Fe vacancies, then Ni and Cr vacancies. Strong interactions between tritium and the metal vacancies are occurring by the formation of Fe—T bonds. The formation of Cr—T, Ni—T, or Al—T bonds are found less energetically favorable than Fe—T bonds.
Mechanical and physical properties of inorganic polymer cement made of iron-rich laterite and lateritic clay: A comparative study
In this work, two different laterites (iron contents of 13.07 and 49.34 wt%, respectively, for lateritic clay, LAC, and iron-rich laterite, LAI) were selected and calcined at 600 °C. The obtained calcined laterites, namely LAI600 and LAC600, were separately mixed with an alkaline solution (silicate modulus of 1.35) or an acidic solution (phosphoric acid solution at pH ≤ 2) for the synthesis of inorganic polymer products. The fabricated products were cured at 20 °C (ambient) and 40 °C (oven). The obtained results showed that the compressive strength of each series of alkaline-based inorganic polymer binder increased with ageing time (7 and 28 days) for room temperature curing, while the reverse trend was noted for oven-cured specimens. The best mechanical performance was obtained when using a phosphoric acid solution, 38 and 52 ± 1 MPa; 62 and 65 ± 1 MPa at 28 days for LAC and LAI respectively. It appeared that a higher iron content within the laterite contributed to an increase in the compressive strength under acidic conditions (LAI (59 MPa) > LAC (48 MPa)) compared to the behavior obtained under alkaline conditions (LAI (6 MPa) < LAC (29 MPa)). Accordingly, the acidic products exhibited a dense structure (with lower porosity) and contained amorphous iron/aluminium phosphate phases such as berlinite (FePO{sub 4}), iron hydrogen phosphate hydrate (Fe{sub 3}H{sub 15}(PO{sub 4}){sub 8·}4H{sub 2}O), ferrowyllieite (AlFe{sub 2}Na{sub 2}(PO{sub 4}){sub 3}) and sodium iron phosphate (Na{sub 3}Fe{sub 2}(PO{sub 4}){sub 3}) arising from the alteration of iron minerals in an acidic medium, confirmed by Mössbauer spectroscopy and electron paramagnetic resonance spectroscopy.
Fission yeast Duf89 and Duf8901 are cobalt/nickel-dependent phosphatase–pyrophosphatases that act via a covalent aspartyl–phosphate intermediate
Domain of Unknown Function 89 (DUF89) proteins are metal-dependent phosphohydrolases. Exemplary DUF89 enzymes differ in their metal and phosphosubstrate preferences. Here, we interrogated the activities and structures of two DUF89 paralogs from fission yeast—Duf89 and Duf8901. We find that Duf89 and Duf8901 are cobalt/nickel-dependent phosphohydrolases adept at hydrolyzing p-nitrophenylphosphate and PP i . Crystal structures of metal-free Duf89 and Co 2+ -bound Duf8901 disclosed two enzyme conformations that differed with respect to the position of a three-helix module, which is either oriented away from the active site in Duf89 or forms a lid over the active site in Duf8901. Lid closure results in a 16 Å movement of Duf8901 Asp195, vis-à-vis Asp199 in Duf89, that brings Asp195 into contact with an octahedrally coordinated cobalt. Reaction of Duf8901 with BeCl 2 and NaF in the presence of divalent cations Co 2+ , Ni 2+ , or Zn 2+ generated covalent Duf8901-(Asp248)–beryllium trifluoride (BeF 3 )•Co 2+ , Duf8901-(Asp248)–BeF 3 •Ni 2+ , or Duf8901-(Asp248)–BeF 3 •Zn 2+ adducts, the structures of which suggest a two-step catalytic mechanism via formation and hydrolysis of an enzyme-(aspartyl)–phosphate intermediate. Alanine mutations of Duf8901 Asp248, Asn249, Lys401, Asp286, and Asp195 that interact with BeF 3 •Co 2+ squelched p-nitrophenylphosphatase activity. A 1.8 Å structure of a Duf8901-(Asp248)–AlF 4 –OH 2 •Co 2+ transition-state mimetic suggests an associative mechanism in which Asp195 and Asp363 orient and activate the water nucleophile. Whereas deletion of the duf89 gene elicited a phenotype in which expression of phosphate homeostasis gene pho1 was derepressed, deleting duf8901 did not, thereby hinting that the DUF89 paralogs have distinct functional repertoires in vivo.
Ab-Initio Simulation Studies of Cr Solvation in Fluoride Molten Salts
Understanding molten salt chemistry is essential in ongoing research of the molten salt nuclear reactor (MSR). In this context, detailed understanding of the mechanisms underlying selective oxidation of metal species, such as Cr, is required to guide the design of effective corrosion mitigation strategies in molten salts. An important starting point for such mechanistic understanding is knowledge of the solvation structure and its role in controlling metal speciation. In this work, we use ab initio molecular dynamics simulations to study the short-range (on the scale of the nearest-neighbor bond lengths) and medium-range (over length scales of several neighbor spacings) structure in three different fluoride melts with and without Cr addition; namely, 2KF-NaF, 2LiF-BeF 2 , and 3LiF-AlF3. We find that Cr 0 ,Cr 2+ ,Cr 3+ can each be coordinated by different numbers of F-, with the variance in coordination number decreasing as oxidation state increases, and that these coordination geometries are largely independent of solvent. The manner by which Cr changes the medium-range structure, however, is found to be solvent-dependent. While 2KF-NaF melts show short and medium range order that is highly dynamic, 2LiF-BeF 2 and 3LiF-AlF 3 are characterized by molecular associates that are relatively long-lived that organize into oligomer structures on larger length scales. Rather than being solvated by F- ions alone, we find that Cr can incorporate into and be solvated within this oligomer structure. Fluoroacidity, alone, may therefore prove too simple a metric for assessing the corrosivity of molten fluorides. As our work suggests, the ability of Cr to solvate must be understood in the context of the short- and medium-range structure of the solvent.
Elucidating the Redox Behavior during Atomic Layer Deposition on Lithium-Ion Battery Cathode Materials
Atomic layer deposition (ALD) has emerged as a promising technology for applying ultrathin protective coatings on lithium-ion battery (LIB) cathode surfaces to improve their cycling stability. While there have been numerous reports evaluating the electrochemical performance of these surface-modified cathode materials, the chemical changes induced on the surface of the cathode materials upon ALD coating are not fully studied. This paper describes a systematic investigation to understand the interfacial changes of 12 different cathode materials upon coating with aluminum oxide (Al 2 O 3 ) using trimethyl aluminum (TMA) and H 2 O, and aluminum fluoride (AlF 3 ) using TMA and hydrogen fluoride pyridine (HFPy). Here, the surface composition of these cathode materials, which range from simple transition metal oxides (e.g. NiO and MnO) to complex multi-element cathode materials (e.g. LiNi x Mn 1-x-y Co y O 2 , NMC), was studied via X-ray photoelectron spectroscopy (XPS). The XPS measurements reveal that the transition metals in the cathode materials undergo selective oxidation/reduction depending upon the nature of the precursor, the coating, and the cathode material. The ability to chemically modify the surface of cathode materials via vapor-phase precursor adsorption will open new avenues to systematically control the interface of the cathode materials in LIBs that are not possible by conventional coating methods.
rRNA methylation by Spb1 regulates the GTPase activity of Nog2 during 60S ribosomal subunit assembly
Biogenesis of the large ribosomal (60S) subunit involves the assembly of three rRNAs and 46 proteins, a process requiring approximately 70 ribosome biogenesis factors (RBFs) that bind and release the pre-60S at specific steps along the assembly pathway. The methyltransferase Spb1 and the K-loop GTPase Nog2 are essential RBFs that engage the rRNA A-loop during sequential steps in 60S maturation. Spb1 methylates the A-loop nucleotide G2922 and a catalytically deficient mutant strain ( spb 1 D52A ) has a severe 60S biogenesis defect. However, the assembly function of this modification is currently unknown. Here, we present cryo-EM reconstructions that reveal that unmethylated G2922 leads to the premature activation of Nog2 GTPase activity and capture a Nog2-GDP-AlF 4 - transition state structure that implicates the direct involvement of unmodified G2922 in Nog2 GTPase activation. Genetic suppressors and in vivo imaging indicate that premature GTP hydrolysis prevents the efficient binding of Nog2 to early nucleoplasmic 60S intermediates. We propose that G2922 methylation levels regulate Nog2 recruitment to the pre-60S near the nucleolar/nucleoplasmic phase boundary, forming a kinetic checkpoint to regulate 60S production. Our approach and findings provide a template to study the GTPase cycles and regulatory factor interactions of the other K-loop GTPases involved in ribosome assembly.
High-throughput studies of novel magnetic materials in borides
Borides are a versatile material family with various properties for valuable applications. Conventional magnetism, such as ferromagnetism and antiferromagnetism in borides, have been extensively studied. However, research on unconventional magnetism in borides where quantum effects are dominant is scarce. Here, we implement a high-throughput workflow combining first-principles calculations, materials prediction, and magnetic properties calculations to discover novel magnetism and magnetic materials in borides. Successfully applying the workflow, we report three families of novel magnetic borides, including two families of borides exhibiting quantum magnetism. One is a family of dimerized quantum magnets among YCrB 4 -type borides, which provides a rare platform for studying the spin-gap quantum critical point. The other is a family of altermagnets among FeMo2B 2 -type borides, extending the magnetic orderings exhibited by borides beyond conventional ferromagnetism and antiferromagnetism. We also predict a family of magnetic laminate transition metal borides, known as the MAB phases, in the AlFe 2 B 2 -type family, which provide pure-phase or alloying candidates for studying magnetocaloric materials and the associated magnetic transitions. The workflow is expected to be used in further studies of novel magnetism and magnetic materials.
Materials Data on Al3H36C12N3F4 by Materials Project
(N(CH3)4)3(AlF)2AlF2 is Silicon tetrafluoride-derived structured and crystallizes in the orthorhombic Cmm2 space group. The structure is zero-dimensional and consists of two difluoroaluminum molecules, four fluoroaluminum molecules, and six tetramethylammonium molecules.