Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ASCENT TRAJECTORY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

A study to evaluate STS heads-up ascent trajectory performance employing a minimum-Hamiltonian optimization strategy

A study was conducted to evaluate the performance implications of a heads-up ascent flight design for the Space Transportation System, as compared to the current heads-down flight mode. The procedure involved the use of the Minimum Hamiltonian Ascent Shuttle Trajectory Evaluation Program, which is a three-degree-of-freedom moment balance simulation of shuttle ascent. A minimum-Hamiltonian optimization strategy was employed to maximize injection weight as a function of maximum dynamic pressure constraint and Solid Rocket Motor burnrate. Performance Reference Mission Four trajectory groundrules were used for consistency. The major conclusions are that for heads-up ascent and a mission nominal design maximum dynamic pressure value of 680 psf, the optimum solid motor burnrate is 0.394 ips, which produces a performance enhancement of 4293 lbm relative to the baseline heads-down ascent, with 0.368 ips burnrate solid motors and a 680 psf dynamic pressure constraint. However, no performance advantage exists for heads-up flight if the current Solid Rocket Motor target burnrate of 0.368 ips is used. The advantage of heads-up ascent flight employing the current burnrate is that Space Shuttle Main Engine throttling for dynamic pressure control is not necessary.

Sinha, Sujit↗
NASA NTRS1974

Optimal payload ascent trajectories of winged vehicles

A trajectory analysis is presented which shows the advantage of lifting ascent and the penalties associated with increased wing mass due to increases in aerodynamic loading. The vehicle analyzed is made up of an orbiter, an expendable liquid fuel tank, and two solid rocket motors. Results of the tradeoff are illustrated in a graph of the total vehicle mass plotted against the trajectory constraint. Results indicate that even when structural mass penalties are considered lifting ascent provides a payload delivery.

Martin, J. A.↗
NASA NTRS1970

Lunar descent and ascent trajectories

Apollo 11 premission planning, real time situation and postflight analysis for lunar descent and ascent phases, providing navigation correction capability for Apollo 12

Bennett, F. V.↗
NASA NTRS1972

Optimal ascent trajectories of a two stage space shuttle vehicle

The effects of aerodynamic lift on the performance capability of a two stage space shuttle are discussed. The performance program uses three degrees of freedom to describe the trajectory of a point mass moving over the rotating earth. Two cases of ascent modes are described and compared. It is concluded that significant improvements in performance through the use of lift appear to be configuration dependent, and for this reason cannot be generalized for all spacecraft configurations.

Wilson, R. A.↗
NASA NTRS2017

Launch Vehicle Ascent Trajectory Simulation Using the Program to Optimize Simulated Trajectories II (POST2)

The Program to Optimize Simulated Trajectories II (POST2) has been continuously developed for over 40 years and has been used in many flight and research projects. Recently, there has been an effort to improve the POST2 architecture by promoting modularity, flexibility, and ability to support multiple simultaneous projects. The purpose of this paper is to provide insight into the development of trajectory simulation in POST2 by describing methods and examples of various improved models for a launch vehicle liftoff and ascent.

Lugo, Rafael A.↗
NASA NTRS1973

Effects of ascent trajectory mode and tank disposal method on shuttle payload accommodation

The effects of external tank disposal by retrorocket versus passive tank drop, and targeting the main engine burn for high apogee versus the baseline parking orbit ascent method on shuttle payload accommodation capability were investigated. Missions launched from Eastern Test Range were investigated over a range of orbit altitudes to determine tank disposal requirements including footprint dispersions and alternate impact locations, performance, and orbital maneuvering system requirements. Passive tank drop also proved to be advantageous from a payload accommodation standpoint. Direct insertion was shown to be a means of accommodating long payloads at higher altitudes than permitted by the baseline ascent method.

Blair, J. C.↗
NASA NTRS1993

Atlas IIAS ascent trajectory design for the SOHO mission

In 1995, an Atlas IIAS launch vehicle will loft the Solar and Heliospheric Observatory (SOHO) as part of the International Solar and Terrestrial Physics program. The operational phase of the SOHO mission will be conducted from a `halo orbit' about the Sun-Earth interior libration point. Depending on the time of the year of launch, the optimal transfer requires a parking orbit of variable duration to satisfy widely varying inertial targets. A simulation capability has been developed that optimizes the launch vehicle ascent and spacecraft transfer phases of flight together, subject to both launch vehicle and spacecraft constraints. It will be shown that this `ground-up' simulation removes the need for an intermediate target vector at Centaur upper stage/spacecraft separation. Although providing only a modest gain in deliverable satellite mass, this capability substantially improves the mission integration process by removing the strict reliance on near-Earth target vectors. Trajectory data from several cases are presented and future applications of this capability are also discussed.

Willen, Robert E.↗
NASA NTRS1990

Optimizing Space Shuttle ascent trajectories within environmental constraints

A method is presented for relating the structural margin requirements for the Space Shuttle Vehicle to flight design criteria. Using this approach, it is possible to develop flight designs that optimize structural margins and payload. It is also shown how wind and environmental data bases are incorporated into the Space Shuttle mission flight design activities.

Whitehead, Douglas S.↗
NASA NTRS1992

Guidance and dispersion studies of National Launch System ascent trajectories

The National Launch System (NLS) is a joint concept, between DoD and NASA, for building a family of new launch vehicles. Two of the many choices to be made are the trajectory shaping methods and the onboard guidance scheme. This paper presents results from some ongoing studies to address these issues. First, potential gains from new guidance concepts are listed. Next the paper gives a list of possible discriminators between different guidance schemes, lists a number of potential guidance schemes, and explains two in some detail. A reference scheme is tested to determine its performance versus the discriminators. Finally, results from some special studies using the reference guidance scheme are given, including the effects of closed-loop guidance initiation time, time of enforcement of sideslip, vehicle roll for engine out, time and location of an engine out, use of load relief control, and use of day of launch wind biasing.

Hanson, John M.↗
NASA NTRS1994

Effect of Aeropropulsive Interactions and Design Sensitivities on Optimal Hypersonic Ascent Trajectories

In this paper, trajectory optimization is used as a tool to better understand the performance characteristics of hypersonic Single-Stage-To-Orbit(SSTO) vehicle exhibiting significant aeropropulsive interactions. The energy state approximation is used to determine a straightforward method of determining the scramjet-powered phase of the mission. The energy state method is then used to generate fuel-optimal trajectory results over this portion of the mission for a vehicle configuration of this class. The fuel-optimal unconstrained trajectory is marked by low-altitude acceleration, while a dynamic pressure-constrained trajectory is seen to ride the dynamic pressure constraint for the entire scramjet mission phase. The significance of aeropropulsive interactions in affecting vehicle performance is also investigated.

Lovell, T. Alan↗
NASA NTRS2010

Evaluating Descent and Ascent Trajectories Near Non-Spherical Bodies

Spacecraft landing on small bodies pass through regions where conventional gravitation formulations using exterior spherical harmonics are inaccurate. An investigation shows that a formulation using interior solid spherical harmonics might be satisfactory. Interior spherical harmonic expansions are usable inside an imaginary, empty sphere. For this application, such a sphere could be positioned in empty space above the intended landing site and rotating with the body. When the spacecraft is inside this sphere, the interior harmonic expansion would be used instead of the conventional, exterior harmonic expansion. Coefficients can be determined by a least-squares fit to gravitation measurements synthesized from conventional formulations. Due to their unfamiliarity, recurrences for interior, as well as exterior, expansions are derived. Hotine's technique for partial derivatives of exterior spherical harmonics is extended to interior harmonics.

Werner, Robert A.↗
NASA NTRS2015

An Expert System-Driven Method for Parametric Trajectory Optimization During Conceptual Design

During the early phases of engineering design, the costs committed are high, costs incurred are low, and the design freedom is high. It is well documented that decisions made in these early design phases drive the entire design's life cycle cost. In a traditional paradigm, key design decisions are made when little is known about the design. As the design matures, design changes become more difficult in both cost and schedule to enact. The current capability-based paradigm, which has emerged because of the constrained economic environment, calls for the infusion of knowledge usually acquired during later design phases into earlier design phases, i.e. bringing knowledge acquired during preliminary and detailed design into pre-conceptual and conceptual design. An area of critical importance to launch vehicle design is the optimization of its ascent trajectory, as the optimal trajectory will be able to take full advantage of the launch vehicle's capability to deliver a maximum amount of payload into orbit. Hence, the optimal ascent trajectory plays an important role in the vehicle's affordability posture yet little of the information required to successfully optimize a trajectory is known early in the design phase. Thus, the current paradigm of optimizing ascent trajectories involves generating point solutions for every change in a vehicle's design parameters. This is often a very tedious, manual, and time-consuming task for the analysts. Moreover, the trajectory design space is highly non-linear and multi-modal due to the interaction of various constraints. When these obstacles are coupled with the Program to Optimize Simulated Trajectories (POST), an industry standard program to optimize ascent trajectories that is difficult to use, expert trajectory analysts are required to effectively optimize a vehicle's ascent trajectory. Over the course of this paper, the authors discuss a methodology developed at NASA Marshall's Advanced Concepts Office to address these issues. The methodology is two-fold: first, capture the heuristics developed by human analysts over their many years of experience; and secondly, leverage the power of modern computing to evaluate multiple trajectories simultaneously and therefore enable the exploration of the trajectory's design space early during the pre- conceptual and conceptual phases of design. This methodology is coupled with design of experiments in order to train surrogate models, which enables trajectory design space visualization and parametric optimal ascent trajectory information to be available when early design decisions are being made.

Dees, Patrick D.↗
NASA NTRS1986

Aerothermodynamics of transatmospheric vehicles

A transatmospheric vehicle (TAV) using airbreathing propulsion requires a long acceleration period within the denser part of the atmosphere to reach orbital speed. The long flight time, coupled with the need for a low-drag configuration, results in severe heating of parts of the vehicle. The ascent peak stagnation point and wing leading edge equilibrium wall temperatures are about 3500 K and 2500 K, respectively, likely requiring some form of mass addition cooling. The corresponding temperatures during entry are 1000 K lower. The vehicle windward centerline temperatures are more moderate, with values peaking around 1300 K during both ascent and entry. Therefore, radiative cooling should be effective over large areas of the vehicle. The windward centerline heat loads during entry are comparable to those for low acceleration ascent trajectories. However, ascent heat loads for the stagnation point and the wing leading edge are about three times higher than those during entry. For comparison, the entry heat load for the TAV's stagnation point is about three times higher than the value for Shuttle. Therefore the ascent heat load at the TAV's stagnation point exceeds the Shuttle's entry value by an order of magnitude.

Tauber, M. E.↗
NASA NTRS1989

Trajectory optimization and guidance for an aerospace plane

The first step in the approach to developing guidance laws for a horizontal take-off, air breathing single-stage-to-orbit vehicle is to characterize the minimum-fuel ascent trajectories. The capability to generate constrained, minimum fuel ascent trajectories for a single-stage-to-orbit vehicle was developed. A key component of this capability is the general purpose trajectory optimization program OTIS. The pre-production version, OTIS 0.96 was installed and run on a Convex C-1. A propulsion model was developed covering the entire flight envelope of a single-stage-to-orbit vehicle. Three separate propulsion modes, corresponding to an after burning turbojet, a ramjet and a scramjet, are used in the air breathing propulsion phase. The Generic Hypersonic Aerodynamic Model Example aerodynamic model of a hypersonic air breathing single-stage-to-orbit vehicle was obtained and implemented. Preliminary results pertaining to the effects of variations in acceleration constraints, available thrust level and fuel specific impulse on the shape of the minimum-fuel ascent trajectories were obtained. The results show that, if the air breathing engines are sized for acceleration to orbital velocity, it is the acceleration constraint rather than the dynamic pressure constraint that is active during ascent.

Mease, Kenneth D.↗
NASA NTRS1962

Rendezvous Guidance Technology

The literature on rendezvous guidance technology is reviewed and a bibliography of about 160 documents is presented. The importance of the proper selection of the ascent trajectory and of the orbit for a manned space station or an orbiting launch complex is emphasized. The way the launch delay problem affects the selection of the ascent trajectory and the target orbit is discussed. A specific ascent trajectory and an orbit for a manned space station or an orbiting launch complex is recommended on the premise that launch delay problems will continue to outweigh most of the other orbit selection criteria. A new method for determining the velocity corrections required for mid-course guidance is proposed . The proposed methods consist of an "exact-numerical" solution of the relative equations of motion in the "Shell-coordinate system." The proposed "exact-numerical" method extends the applicability of the mid- course equations to a much greater range than that of the currently available linear methods .

Trajectory↗
NASA NTRS2019

Space Launch System and Missions to Near Rectilinear Halo Orbits

The first major evolution of NASA’s Space Launch System (SLS) will begin its flights starting in the mid-2020’s. This new configuration, called Block 1B, replaces the Interim Cryogenic Propulsion Stage with a larger Exploration Upper Stage (EUS). The additional capability provided by the new upper stage will allow SLS to send heavier payloads into deep space. One destination of interest to the SLS program is called a Near Rectilinear Halo Orbit (NRHO). This is a type of lunar orbit with multiple advantages for deep space exploration. These benefits include Earth/lunar access, low station-keeping requirements, and high communication potential with Earth. Therefore, it is a leading candidate for the proposed Lunar Orbital Platform-Gateway (LOP-G). This paper will provide a detailed assessment of the SLS Block 1B requirements and capabilities for sending payloads to an NRHO. Analysts at Marshall Space Flight Center are producing a multi-year mission availability scan for the SLS Block 1B configuration to a predefined NRHO orbit. The analysis produces an optimized trajectory for each day of the scan window. A maximized payload and minimized propellant requirement are determined for each day. All maneuvers from launch to the end of the Trans-Lunar-Injection (TLI) are being modeled as finite burns. Injections into an NRHO are being modeled as impulsive maneuvers. The payload element is arbitrary, but includes sufficient mass to represent a large habitat or propulsion module. The resulting parameters of payload capability, delta-v requirements, and launch windows length vary over the course of the scan. Many launch days in the scan are eliminated in post-processing as they violate mission constraints such as payload mass and propellant usage to insert into an NRHO. Based off previous one-year scan results for the SLS Block 1B Design Analysis Cycle 2 (DAC-2), it is expected that there will be one to three days per week where the payload is able to insert into an NRHO within SLS constraints objectives. This scan provides results for longer than one-year, allowing analysts to better understand the launch availability and energy requirements of SLS Block 1B over time. The in-space mission design and scans utilize Copernicus, an n-body trajectory optimization tool originally developed out of the University of Texas at Austin with further development at Johnson Space Center in Houston, TX. To seed the in-space trajectory, Copernicus uses a plugin to call a database of SLS ascent trajectories optimized in the Program to Simulate Optimized Trajectories II (POST2). The ascent trajectories are developed using a framework that parametrizes payload mass and LEO inclination, and targets a 100 nmi (nautical mile) altitude circular parking orbit. Though this analysis is specific to the SLS program, it will provide a summary of mission design benefits and constraints associated with generic NRHO access, and may be applied to other programs or concepts that will utilize this orbit.

Statham, T. L.↗