Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “3D CAD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Evaluation of intracoronary hemodynamics identifies perturbations in vorticity

Coronary artery disease (CAD) is highly prevalent and associated with adverse events. Challenges have emerged in the treatment of intermediate coronary artery stenoses. These lesions are often interrogated with fractional flow reserve (FFR) testing to determine if a stenosis is likely to be causative for ischemia in a cardiac territory. This invasive test requires insertion of a pressure wire into a coronary vessel. Recently computational fluid dynamics (CFD) has been used to noninvasively assess fractional flow reserve in vessels reconstructed from medical imaging data. However, many of these simulations are unable to provide additional information about intravascular hemodynamics, including velocity, endothelial shear stress (ESS), and vorticity. We hypothesized that vorticity, which has demonstrated utility in the assessment of ventricular and aortic diseases, would also be an important hemodynamic factor in CAD. Three-dimensional (3D), patient-specific coronary artery geometries that included all vessels >1 mm in diameter were created from angiography data obtained from 10 patients who underwent diagnostic angiography and FFR testing (n = 9). A massively parallel CFD solver (HARVEY) was used to calculate coronary hemodynamic parameters including pressure, velocity, ESS, and vorticity. These simulations were validated by comparing velocity flow fields from simulation to both velocities derived from in vitro particle image velocimetry and to invasively acquired pressure wire-based data from clinical testing. There was strong agreement between findings from CFD simulations and particle image velocimetry experimental testing (p < 0.01). CFD-FFR was also highly correlated with invasively measured FFR (ρ = 0.77, p = 0.01) with an average error of 5.9 ± 0.1%. CFD-FFR also had a strong inverse correlation with the vorticity (ρ = -0.86, p = 0.001). Simulations to determine the effect of the coronary stenosis on intravascular hemodynamics demonstrated significant differences in velocity and vorticity (both p < 0.05). Further evaluation of an angiographically normal appearing non-FFR coronary vessel in patients with CAD also demonstrated differences in vorticity when compared with FFR vessels (p < 0.05). The use of highly accurate 3D CFD-derived intravascular hemodynamics provides additional information beyond pressure measurements that can be used to calculate FFR. Vorticity is one parameter that is modified by a coronary stenosis and appears to be abnormal in angiographically normal vessels in patients with CAD, highlighting a possible use-case in preventative screening for early coronary disease.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

PUFFIn Software Modeling for Quality Management

PUFFIn (PENELOPE User Friendly Fast Interface) was designed as a fast and simple Monte Carlo simulation tool for the transport of photons and electrons, with a primary purpose as a learning and education tool for a broad range of static configurations in the radiation processing industry. Development of the PUFFIn software is funded by the Office of Radiological Security (ORS) within the United States National Nuclear Security Administration (NNSA). PUFFIn helps fill the education and knowledge gaps in the industry, as identified in reports by Fermilab (2017) and the IAEA (2020). PUFFIn uses the PENELOPE (NEA-2023) physics engine to perform simulations on static configurations. PUFFIn has support for multiple geometry types from simple, single material simulations to full 3D configurations created from CAD input files or images from X-Ray Tomography scans. PUFFin was designed to be easy for the novice user, it will generate the input and geometry files required by PENLOPE and will display the output plots within the PUFFIn interface. PUFFin is distributed for free but requires a free workshop so users can be adequately trained in its use. Workshops have been presented in the past at Texas A&M university, the Aerial-CRT facility in Strasbourg France and Jakarta Indonesia. PUFFIn simulations have been validated by 10 MeV ebeam experiments done at Aerial-CRT in France (Radiation Physics and Chemistry 222 (2024) 111774). Further user experimental comparisons were made at the medical product hands on workshop at Texas A&M in October 2024.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Integration of Open-Source URBANopt and Dragonfly Energy Modeling Capabilities into Practitioner Workflows for District-Scale Planning and Design

High-performance districts and communities offer opportunities for reducing energy use, emissions, and costs, and can be instrumental in helping cities achieve their climate goals. The design of such communities requires identification of opportunities early on and their re-evaluation throughout the planning process. There is a need for energy modeling tools that connect 3D Computer-Aided Design (CAD) platforms to simulation engines, enabling detailed energy analysis of districts within the workflows and tools used by practitioners. This paper introduces the Dragonfly and URBANoptTM combined toolset that supports the creation of urban models from a range of geometry formats typically used by designers and planners, and provides an integrated pathway to simulate district-scale energy systems. The toolset is piloted by a global architecture and master planning firm to evaluate several key urban-scale technical questions for the design of a district in Chicago. The findings indicate that, while energy savings can be achieved through traditional architectural studies and enhancements to individual building efficiency, the modeling toolset helps identify additional savings and insights that can be achieved when considering district-scale energy systems. Finally, this study demonstrates how the Dragonfly/URBANopt toolset can integrate with master planning workflows, thereby enabling an iterative performance-based design process.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

Processing MCNP Elemental Edit Outputs

The Monte Carlo N-Particle (MCNP) transport code version 6 (also known as MCNP6) has the capability for tracking particles on unstructured mesh (UM) geometry models embedded into constructive solid geometry (CSG) cells. A UM geometry is a collection of elements representing a solid geometry. The first step of MCNP UM modeling is using other software packages to create a finite element mesh representation of a solid 3D geometry. Computer-aided design (CAD) or computer-aided manufacturing (CAM) software is typically used to create a solid geometry model, which is later imported into mesh generation software to create a UM model. The MCNP UM feature was originally designed for models generated by the Abaqus/CAE software. The MCNP code version 6.0 and later can process UM models formatted as Abaqus input files. MCNP can process a UM model consisting of several different element types including linear tetrahedral or hexahedral elements and calculate quantities of interest such as flux and energy deposition at elements. An MCNP UM simulation provides high-fidelity elemental edit (i.e., tally) outputs, which can be further used in multiphysics calculations. The MCNP UM feature was used for multiphysics simulations where quantities of interest calculated by MCNP are used as inputs for heat transfer calculations in Abaqus. MCNP6.3 can produce two types of elemental edit output (EEOUT) file formats: ASCII and HDF5. An EEOUT file type must be requested on an EMBED card while output type (flux or energy deposition) must be requested on an EMBEE card. We wrote Python3 scripts to extract energy deposition values in an ASCII or HDF5 EEOUT file and compute a heat flux profile for an Abaqus heat transfer calculation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Full-wave modeling of RF waves in fusion plasmas with finite element method: Progress in past decades and its future role

This paper reviews the progress in computing radio frequency (RF) wave fields in fusion plasmas, specifically focusing on simulations utilizing the finite element method (FEM) over the past few decades. Computing RF wave fields in fusion plasmas presents unique challenges due to large simulation domains, complex antenna structures, non-local dielectric properties, and wide ranges of spatial scales. It highlights key developments and outlines future directions, primarily addressing waves in the ion cyclotron (IC) to lower hybrid (LH) frequency range. We begin with briefly revisiting earlier developments before the widespread availability of modern computer-aided engineering (CAE) software based on FEM. This historical perspective illuminates early progress and the physics difficulties that motivated ongoing work within the community. Modern wave simulations for RF antennas based on FEM are characterized by the use of detailed 3D antenna model geometry generated from engineering CAD software and localized wave dielectric model. Significant advancements have also been made in improving physics models to include phenomena such as RF sheath rectification and wave scattering. FEM-based RF simulations have also been applied to compute wave propagation in the core region, where the inclusion of non-local dielectric response is crucial. This is a challenging goal, and several promising approaches have been proposed in this area. Additionally, RF simulation development initiatives based on open-source libraries have gained popularity, demonstrating scalability and flexibility in extending physics models. This paper will discuss the advantages and disadvantages of using such a publicly available FEM library.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Cooling Strategies for an Electric Motor with Additively Manufactured Hollow Conductors and Distributed Power Electronics Integrated with Heat Pipes

This paper discusses design tradeoffs and thermal modeling explored in cooling strategies for an aircraft propulsion electric motor with additively manufactured coils and distributed power electronics integrated with heat pipes. Design tradeoffs include heat pipe Qmax performance related to inclination, condenser configuration, coolant type, coolant flow path complexity, and ease of access to modular power electronics. Three cooling strategies were selected and realized into CAD models. These models were further evaluated using 3D thermal FEA and optimization tools to explore cooling geometry details that include fin thickness, spacing and count with the objective to minimize fin mass under a set of constraints. Lastly, motorette test data is presented comparing air versus liquid cooling of heat pipes.

additive manufacturing↗
DOE OSTI2023

4. Geometry Data Storage

3D-printing begins with the design of an object using computer aided design (CAD) software. The geometry of the object must be exported and saved in a data file format that can be used in the slicing process to generate machine instructions for printing. The standard method of saving the data is to tessellate the object as a triangulated mesh stored as a .stl file. Due to the flat triangular faces used to store the data, this mesh is a low-resolution representation of the high-fidelity object designed in CAD. The STL has its limitations with respect to geometrical accuracy, material information, and instances of invalid mesh data, but can still be used for the 3D-printing process. New file variants, such as OBJ, AMF, and 3MF, are being developed to fix some of these issues and increase the capabilities of geometry data storage for 3D-printing.

Roschli, Alex↗
DOE OSTI2023

CrossLink: Meshing a 3D part from a STEP file [Slides]

This example shows how to use CrossLink to create a mesh for a 3D geometry part read in from a STEP file. A STEP file (Standard for the Exchange of Product data) is a common file format used for 3D modelling that can be written out from a CAD program (e.g., Creo Parametric). Being able to read and mesh STEP file geometries is essential for meshing parts from engineering models. Creating the mesh typically involves: (1) Importing the geometry; (2) Creating geometry groups; (3) Assigning curves and surfaces to the geometry groups; (4) Building a topology; (5) Applying geometric and mesh constraints; and (6) Generating the final mesh. Current issues with this process in CrossLink include: (1) The GUI does not display trimmed surfaces; (2) The user must manually create and assign geometry groups; and (3) The user must be aware of duplicate curves and surfaces from the CAD model.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

Design and scale-up of 3D printed bat houses with biomass-derived polymer composites

Biomass (e.g., pine sawdust, especially high–ash content pine sawdust) is commonly disposed of as waste. Combining biomass with polymers to make composite feedstocks for 3D printing has been explored as a method to reduce or repurpose the biomass waste. Although not all biocomposite properties are known, the wood-based polylactic acid (PLA) composite has promising qualities for applications in ecological settings. In this work, pine wood–PLA composite feedstock was used to 3D print supplemental roost structures for endangered tree-roosting bats, which often face a paucity of suitable naturally occurring roosts. This material combination was selected because it is estimated to degrade faster than the synthetic material systems that are used widely in supplemental bat roosting structures to aid in the conservation of tree roosting bats. The layered, rough surface created by the 3D printing process serves as a surface that bats can grip while roosting. Computer-aided design (CAD) models were generated based on natural roost structures, and a full-size bat house was successfully additively manufactured using a pellet-fed large-scale 3D printing system. The 3D printed hexagon exhibited a tensile strength of 22–23 MPa and a Young’s modulus of 3202–3218 MPa in the x-direction. It has been demonstrated that the 3D printed bat house can be installed on a tree in a stable fashion. This successful demonstration of a bat roost manufactured using a bioderived composite should promote its use in other fish and wildlife structures and broader industrial applications such as construction and automobiles.

3D printing↗
DOE OSTI2021

Comprehension of Spatial Constraints by Neural Logic Learning from a Single RGB-D Scan

Autonomous industrial assembly relies on the precise measurement of spatial constraints as designed by computer-aided design (CAD) software such as SolidWorks. This paper proposes a framework for an intelligent industrial robot to understand the spatial constraints for model assembly. An extended generative adversary network (GAN) with a 3D long short-term memory (LSTM) network was designed to composite 3D point clouds from a single RGB-D scan. The spatial constraints of the segmented point clouds are identified by a neural-logic network that incorporates general knowledge of spatial constraints in terms of first-order logic. The model was designed to comprehend a complete set of spatial constraints that are consistent with industrial CAD software, including left, right, above, below, front, behind, parallel, perpendicular, concentric, and coincident relations. The accuracy of 3D model composition and spatial constraint identification was evaluated by the RGB-D scans and 3D models in the ABC dataset. The proposed model achieved 57.23% intersection over union (IoU) in 3D model composition, and over 99% in comprehending all spatial constraints.

Wang, Dali↗
DOE OSTI2023

Generating MCNP Input Files for Unstructured Mesh Geometries

The Los Alamos National Laboratory’s (LANL) Monte Carlo N-Particle (MCNP)1 transport code version 6.3 (also known as MCNP6.3) has the capability for tracking particles on unstructured mesh (UM) geometry models embedded into constructive solid geometry (CSG) cells. This feature has been developed for performing calculations of complex geometry models because manually creating CSG models is time-consuming and error-prone as the complexities of geometries increase. A UM geometry model is a collection of finite elements representing a solid geometry. The first step of the MCNP UM calculation is using other software packages to create a finite element mesh representation of a solid 3D geometry because the MCNP code cannot be used to generate a UM model. Computer-aided design (CAD) software is typically used to create a solid geometry model, which is later imported into mesh generation software to create a UM model. Some mesh generation software packages may also be used to create solid geometries and thus CAD files are not needed. The MCNP UM feature was originally designed for models generated by the Abaqus/CAE software suite. The MCNP code version 6.0 and later can process UM models formatted as Abaqus input files. Starting with a 6.3 version, the MCNP code can process HDF5 mesh input files. We only focus on the UM models formatted as Abaqus input files in this report since currently no external software can be used to generate HDF5 mesh input files for MCNP UM calculations. The MCNP code version 6.3 can be used to convert the Abaqus mesh input files into the HDF5 mesh input files, but this option is typically used by the MCNP code development team to test the HDF5 mesh input file feature. Several software packages (such as Abaqus, Attila4MC, or Cubit) can be used to create the Abaqus input files for MCNP UM calculations. An MCNP UM calculation using an Abaqus model requires two input file types: MCNP and Abaqus input files. The Abaqus input files needed for MCNP UM calcu lations must have the correct Abaqus syntax and meet the additional requirements by the MCNP code. The MCNP code can process only Abaqus input files that make use of part and assembly definitions, where elements in each part must be grouped into one or more element sets (i.e., elset) using *Elset keyword lines with specified naming formats. The MCNP and Abaqus input files required for MCNP UM simulations must be related; pseudo-cells in an MCNP input file must be constructed from mesh model data from an Abaqus input file. For large complex UM models, it is tedious to manually create MCNP UM input files. The um pre op (unstructured mesh pre operations) program with the -m option can be used to create a skeleton MCNP input file from an Abaqus input file [6]. Since the um pre op program was written in Fortran and was not written for optimized performance, this program is a deprecated feature in the MCNP code version 6.3 and may be removed in the next release of the code. To improve calculation flow of multiphysics calculations, a Python3 code called write mcnp um input has been developed to generate an MCNP input file instead of using the um_pre_op -m option. This Python code was initially released to the public in 2020. We have updated this Python code for MCNP6.3 and it was used to generate the MCNP input files used to verify the MCNP6.3 code. The write_mcnp_um_input code is included with the MCNP6.3 code package which will be released to the public through the Radiation Safety Information Computational Center (RSICC) at Oak Ridge National Laboratory. This report is a revision of LA-UR-20-27139 report.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Robust Containment Queries over Collections of Trimmed NURBS Surfaces via Generalized Winding Numbers

Here, we propose a containment query that is robust to the watertightness of regions bound by trimmed NURBS surfaces, as this property is difficult to guarantee for in-the-wild CAD models. Containment is determined through the generalized winding number (GWN), a mathematical construction that is indifferent to the arrangement of surfaces in the shape. Applying contemporary techniques for the 3D GWN to trimmed NURBS surfaces requires some form of geometric discretization, introducing computational inefficiency to the algorithm and even risking containment misclassifications near the surface. In contrast, our proposed method leverages properties of the 3D solid angle to solve the relevant surface integral using a boundary formulation with rapidly converging adaptive quadrature. Batches of queries are further accelerated by memoizing (i.e., caching and reusing) quadrature node positions and tangents as they are evaluated. We demonstrate that our GWN method is robust to complex trimming geometry in a CAD model, and is accurate up to arbitrary precision at arbitrary distances from the surface. The derived containment query is therefore robust to model non-watertightness while respecting all curved features of the input shape.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Simurgh: A Framework for Cad-Driven Deep Learning Based X-Ray CT Reconstruction

High-resolution X-ray computed tomography (XCT) is an important technique for the inspection of additively manufactured (AM) parts. While XCT is typically used off-line to inspect a subset of manufactured parts, significantly accelerating measurement speed while retaining accuracy would enable use of XCT for in-line inspection to rapidly identify defects in each part as it is manufactured. Here, we propose a deep learning (DL) based approach that uses computer aided design (CAD) models of the AM parts and physics-based information to rapidly produce high-quality reconstructions from sparse XCT measurements without high quality ground truth data. Our approach uses a generative adversarial neural network (GAN) to produced realistic training data from the CAD-based simulations and a deep neural network that is trained using data from the first stage to produce accurate 3D reconstructions. Using experimental XCT data of metal parts, we demonstrate enhanced defect detection capabilities while dramatically reducing the scan time.

Ziabari, Amir↗
DOE OSTI2025

LLMs for Mfg.—On the State of Large Language Models and Applications to Manufacturing

Additive Manufacturing (AM), referred to as 3D printing, has emerged as a key pillar of Industry 4.0 enabling layer-by-layer fabrication of intricate geometries from CAD models. In parallel, Large Language Models (LLMs), deep learning models for natural language generation trained on vast text corpora, have demonstrated unprecedented capabilities in understanding and generating human-like text. The convergence of these trends opens new opportunities at the intersection of AM and AI/ML, where LLMs can assist engineers and researchers in design, manufacture planning, and knowledge discovery. Recent academic work has begun to explore LLM applications in AM and adjacent fields, such as material science, mechanical engineering, and design for additive manufacturing. This exploration ranges from intelligent process planning to domain-specific knowledge retrieval. This survey provides a comprehensive review of current developments, focusing on peer-reviewed literature contributions that apply, adapt, and advance LLMs in general and domain-specific domains. We analyze state-of-the-art (SOTA) techniques, such as fine-tuning foundational models for specific domains, retrieval-augmented generation (RAG) pipelines, knowledge graph integration, and delve into the architectures and evaluation methods employed. The goal of this survey is to inform researchers and practitioners of the current capabilities and limitations of LLMs in general and in domain-specific applications, and to outline how these models are being tailored to meet the requirements of these applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Mu2e Target Thermal Test Project

The Mu2e experiment requires a production target capable of operating under extreme thermal conditions caused by an 8 GeV proton beam. This project’s objective supports the development of the Mu2e Production Target by testing the Stickman model’s thermal behavior. To test this, Angel Flores Luviano has assisted Jonathan Williams in progressing this project by contributing to the development of a Radiative Cooling Test Fixture (RCTF) that will be used to evaluate the thermal behavior of the new production target model. Engineering calculations were performed to analyze thermal performance and pressure drop within the cold well and water cooling circuit, and determine optimal sizing for key components of the water system. An engineering note was made to document the calculations. CAD models of the water circuit piping, thermocouple mount, and radiator chimney were developed, and prototype test rig components were fabricated using 3D printing. Future work will focus on conti nued RCTF development which includes control system integration, heater hardware design, and interfaces that can be scaled up to increase thermal capacity.

Luviano, Angel Flores [Unlisted]↗
DOE OSTI2026

Mu2e Production Target Thermal Test Project

The Mu2e experiment requires a production target that is capable of operating under extreme thermal conditions caused by an 8 GeV proton beam. This project’s objective supports the development of the Mu2e Pro- duction Target by testing the Stickman model’s thermal behavior. Angel Flores Luviano has assisted Jonathan Williams in progressing this project by contributing to the development of a Radiative Cooling Test Fixture (RCTF) that will be used to evaluate the thermal behavior of the new production target model. Engineering calculations were performed to an- alyze thermal performance and pressure drop within the cold well and wa- ter cooling circuit. These calculations also determined the optimal sizing for key components of the water system. An engineering note was made to document these calculations. CAD models of the water circuit piping, thermocouple mounting bars, and radiator chimney were developed, and prototype test rig components were fabricated using 3D printing. Future work will focus on continued RCTF development which includes control system integration, heater hardware design, and interfaces that can be scaled up to increase thermal capacity.

Flores Luviano, Angel Augusto [Unlisted, US]↗
DOE OSTI2021

A software package for plasma facing component analysis and design: the Heat flux Engineering Analysis Toolkit (HEAT)

The engineering limits of plasma facing components (PFCs) constrain the allowable operational space of tokamaks. Poorly managed heat fluxes that push the PFCs beyond their limits not only degrade core plasma performance via elevated impurities, but can also result in PFC failure due to thermal stresses or melting. Simple axisymmetric assumptions fail to capture the complex interaction between 3D PFC geometry and 2D or 3D plasmas. This results in fusion systems that must either operate with increased risk or reduce PFC loads, potentially through lower core plasma performance, to maintain a nominal safety factor. High precision 3D heat flux predictions are necessary to accurately ascertain the state of a PFC given the evolution of the magnetic equilibrium. A new code, the Heat flux Engineering Analysis Toolkit (HEAT), has been developed to provide high precision 3D predictions and analysis for PFCs. HEAT couples many otherwise disparate computational tools together into a single open source python package. Magnetic equilibrium, engineering CAD, finite volume solvers, scrape off layer plasma physics, visualization, high performace computing, and more, are connected in a single web-based user interface. Linux users may use HEAT without any software prerequisites via an appImage. This manuscript introduces HEAT, discusses the software architecture, presents first HEAT results, and outlines physics modules in development.

divertor physics↗