Production of high-yield short-chain oligomers from cellulose via selective hydrolysis in molten salt hydrates and separation
Stepwise process of cellulose being hydrolyzed into oligomers in MSH followed by product separation.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Stepwise process of cellulose being hydrolyzed into oligomers in MSH followed by product separation.
The main goal of this proposal is the search for a narrow cryptoexotic nucleon resonance by scanning of the {pi}{sup -}p system invariant mass in the region (1610-1770) MeV with the detection of {pi}{sup -}p and K{lambda} decays. The scan is supposed to be done by the variation of the incident {pi}{sup -} momentum and its measurement with the accuracy of up to {+-}0.1%(better than 1 MeV in terms of the invariant mass in the whole energy range) with a set of proportional chambers located in first focus of the magneto-optical channel. High sensitivity of the method to the resonance under search is shown. The secondary particles scattered from a liquid hydrogen target are detected by sets of the wire drift chambers equipped with modern electronics.Now it is achieved the pion beam momentum resolution better than 0.1% at P{sub {pi}} = 1.5 GeV/c. The wire drift chambers are in preparation. The liquid hydrogen target is tested. The first experimental accelerator run can be at the end of 2008 year.
The COMPASS experiment at CERN studies diffractively produced states in the light quark sector with unprecedented statistics. The observation of f{sub 0}(1500)/f{sub 2}'(1525) decaying to {eta}{eta} in 2008 data with incoming negative pion beam at 190 GeV/c poses the question whether it is produced centrally or formed by the decay of a heavier diffractively produced {pi}{sub 1}(1800)/{pi}{sub 2}(1880). To decide, a dedicated amplitude analysis which includes different production mechanisms is formulated and compared with one which was used to fit centrally produced resonances including f{sub 0}(1500) by the WA102 experiment. Unbinned mass-dependent log-likelihood fitting methods may serve to solve the ambiguities which are present in binned, mass-independent partial wave analyses.
Model predictions regarding the excited baryon spectrum provided by Constituent Quark Models show good agreement with experimental measurements in the low-energy region less than {approx_equal}1.8 GeV. The mass region above {approx_equal}1.8 GeV, however, contains many resonances which are predicted to exist by these models but have not been experimentally verified. The analysis of a double meson final state using linearly polarized photoproduction data allows access to two polarization observables, I{sup s} and I{sup c}(also known as the beam asymmetry {Sigma} for a single meson final state). It has been shown that measurements of these polarizaton observables can provide insight into this missing resonance problem. This analysis was carried out on data taken from the CLAS-g8b data run period conducted at Jefferson Lab in Newport News, Virginia. The analysis of this data and preliminary measurements of these obsevables will be dicussed.
We have used a 45 μJ laser pulse to accelerate the free surface of fine-grained tantalum films up to peak velocities of ∼1.2 km s{sup −1}. The films had thicknesses of ∼1–2 μm and in-plane grain widths of ∼75–150 nm. Using ultrafast interferometry, we have measured the time history of the velocity of the surface at different spatial positions across the accelerated region. The initial part of the histories (assumed to correspond to the “elastic precursor” observed previously) exhibited measured strain rates of ∼0.6 to ∼3.2 × 10{sup 9 }s{sup −1} and stresses of ∼4 to ∼22 GPa. Importantly, we find that elastic amplitudes exhibit little variation with strain rate for a constant peak surface velocity, even though, via covariation of the strain rate with peak surface velocity, they vary with strain rate. Furthermore, by comparison with data obtained at lower strain rates, we find that amplitudes are much better predicted by peak velocities rather than by either strain rate or sample thickness.
Explore the source record for details and available documents.
No abstract prepared.
We compute g{sub D}{sup *}{sub D{pi}} and g{sub B}{sup *}{sub B{pi}} using a framework in which all elements are constrained by Dyson-Schwinger equation studies of QCD and therefore incorporates a consistent, direct, and simultaneous description of light and heavy quarks and the states they may constitute. We link these couplings with the heavy-light-meson leptonic decay constants and thereby obtain g{sub D}{sup *}{sub D{pi}}=15.9{sub -1.0}{sup +2.1} and g{sub B}{sup *}{sub B{pi}}=30.0{sub -1.4}{sup +3.2}. From the latter, we infer g{sub B}=0.37{sub -0.02}{sup +0.04}. A comparison between g{sub D}{sup *}{sub D{pi}} and g{sub B}{sup *}{sub B{pi}} indicates that when the c quark is a system's heaviest constituent, {Lambda}{sub QCD}/m{sub c}-corrections are not under good control.
No abstract prepared.
No abstract prepared.
No abstract prepared.
No abstract prepared.
Explore the source record for details and available documents.
Not Available
Abstract not provided.
The ability to localize defects in order to understand failure mechanisms in complex superconducting electronics circuits, while operating at low temperature, does not yet exist. Here, this work applies thermally-induced voltage alteration (TIVA), to a biased superconducting electronics (SCE) circuit at ambient temperature. TIVA is a commonly used, laser-based failure analysis technique developed for silicon-based microelectronics. The non-operational circuit consisted of an arithmetic logic unit (ALU) in a high-frequency test bed designed at HYPRES and fabricated by MIT Lincoln Laboratory using their SFQ5ee process. Localized TIVA signals were correlated with reflected light images at the surface, and these sites were further investigated by scanning electron microscopy imaging of focused ion-beam cross-sections. The areas investigated, where prominent TIVA signals were observed, showed seams in the Nb wiring layers at contacts to Josephson junctions or inductors and/or disrupted junction morphologies. Finally, these results suggest that the TIVA technique can be used at ambient temperature to diagnose fabrication defects that may cause low temperature circuit failure.