Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “torque control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Integrated Power and Attitude Control for a Spacecraft with Flywheels and Control Moment Gyroscopes

A law is designed for simultaneous control of the orientation of an Earth-pointing spacecraft, the energy stored by counter-rotating flywheels, and the angular momentum of the flywheels and control moment gyroscopes used together as all integrated set of actuators for attitude control. General. nonlinear equations of motion are presented in vector-dyadic form, and used to obtain approximate expressions which are then linearized in preparation for design of control laws that include feedback of flywheel kinetic energy error as it means of compensating for damping exerted by rotor bearings. Two flywheel 'steering laws' are developed such that torque commanded by all attitude control law is achieved while energy is stored or discharged at the required rate. Using the International Space Station as an example, numerical simulations are performed to demonstrate control about a torque equilibrium attitude and illustrate the benefits of kinetic energy error feedback.

Roithmayr, Carlos M.↗
NASA NTRS2006

GOES-R STATIONKEEPING AND MOMENTUM MANAGEMENT

The NOAA Geostationary Operational Environmental Satellites (GOES) fire thrusters to remain within a 1deg longitude-latitude box and to dump accumulated angular momentum. In the past, maneuvers have disrupted GOES imaging due to attitude transients and the loss of orbit knowledge. If the R-series of spacecraft to be launched starting in 2012 were to follow current practice, maneuvers would still fail to meet Image Navigation and Registration (INR) specifications during and after thruster firings. Although maneuvers and recovery take only one percent of spacecraft lifetime, they sometimes come at inopportune times, such as hurricane season, when coverage is critical. To alleviate this problem, thruster firings small enough not to affect imaging are being considered. Eliminating post-maneuver recovery periods increases availability and facilitates autonomous operation. Frequent maneuvers also reduce 1ongitudeAatitude variation and allow satellite co-location. Improved orbit observations come from a high-altitude GPS receiver, and improved attitude control comes from thruster torque compensation. This paper reviews the effects of thruster firings on position knowledge and pointing control and suggests that low-thrust burns plus GPS and feedforward control offer a less disruptive approach to GOES-R stationkeeping and momentum management.

Chu, Donald↗
NASA NTRS1981

Remote control canard missile with a free-rolling tail brake torque system

An experimental wind-tunnel investigation has been conducted at supersonic Mach numbers to determine the static aerodynamic characteristics of a cruciform canard-controlled missile with fixed and free-rolling tail-fin afterbodies. Mechanical coupling effects of the free-rolling tail afterbody were investigated using an electronic/electromagnetic brake system that provides arbitrary tail-fin brake torques with continuous measurements of tail-to-mainframe torque and tail-roll rate. Results are summarized to show the effects of fixed and free-rolling tail-fin afterbodies that include simulated measured bearing friction torques on the longitudinal and lateral-directional aerodynamic characteristics.

Blair, A. B., Jr.↗
NASA NTRS2007

Algorithm Optimally Allocates Actuation of a Spacecraft

A report presents an algorithm that solves the following problem: Allocate the force and/or torque to be exerted by each thruster and reaction-wheel assembly on a spacecraft for best performance, defined as minimizing the error between (1) the total force and torque commanded by the spacecraft control system and (2) the total of forces and torques actually exerted by all the thrusters and reaction wheels. The algorithm incorporates the matrix vector relationship between (1) the total applied force and torque and (2) the individual actuator force and torque values. It takes account of such constraints as lower and upper limits on the force or torque that can be applied by a given actuator. The algorithm divides the aforementioned problem into two optimization problems that it solves sequentially. These problems are of a type, known in the art as semi-definite programming problems, that involve linear matrix inequalities. The algorithm incorporates, as sub-algorithms, prior algorithms that solve such optimization problems very efficiently. The algorithm affords the additional advantage that the solution requires the minimum rate of consumption of fuel for the given best performance.

Motaghedi, Shi↗
NASA NTRS2011

Planar Rotary Motor Using Ultrasonic Horns

One of the first piezoelectric motor designs with significant rotational speeds was outlined by Barth. This device used extensional piezoelectric elements to produce a time varying force at a distance r from the center of a centrally supported disk. These extensional actuators produced micro-steps at a high frequency with the end result being macroscopic rotation of the disk and high torque. The rotation direction is controlled by the choice of the actuators and the direction of the extension about the rotor center. A recent advancement in producing pre-stressed power ultrasonic horns using flexures allows for the development of high torque ultrasonic motors based on the Barth's idea that can be fabricated in a 2D plate or in more complicated 3D structures. In addition to the pre-stress flexures the design also allows for the use of flexures to produce the rotor/horn normal force. The torque can be controlled by the number of actuators in the plane and the amplitude of the normal force. This paper will present analytical and experimental results obtained from testing prototype planar motors.

ultrasonic impacts.↗
NASA NTRS1993

Miniature linear-to-rotary motion actuator

A miniature hydraulic actuation system capable of converting linear actuator motion to control surface rotary motion has been designed for application to active controls on dynamic wind tunnel models. Due to space constraints and the torque requirements of an oscillating control surface at frequencies up to 50 Hertz, a new actuation system was developed to meet research objectives. This new actuation system was designed and developed to overcome the output torque limitations and fluid loss/sealing difficulties associated with an existing vane type actuator. Static control surface deflections and dynamic control surface oscillations through a given angle are provided by the actuation system. The actuator design has been incorporated into a transonic flutter model with an active trailing edge flap and two active spoilers. The model is scheduled for testing in the LaRC 16 Foot Transonic Dynamics Tunnel during Summer 1993. This paper will discuss the actuation system, its design, development difficulties, test results, and application to aerospace vehicles.

Sorokach, Michael R., Jr.↗
NASA NTRS1978

On attitude estimation schemes for fine-pointing control

This paper studies single-axis equations of motion that are applicable to a spacecraft or to a space experiment pointing assembly whose motion has been perfectly isolated from the carrier vehicle. It considers four state estimators for implementation in the control loop for a stellar observation experiment. The first three estimators are very general and do not make use of input torque in their prediction models, while the proposed fourth estimator utilizes this information. It is shown via closed-loop covariance analysis that the best achievable pointing performance with the best of the first three estimators is limited to about 0.125 arc-sec (rms) with the given rate-gyro and star-tracker inaccuracies. It is also shown that the fourth estimator has the capability of achieving a pointing performance far superior to the performance achievable using the first three estimators. The fourth estimator relies on the ability to accurately generate the desired control torque (i.e., low input noise).

Joshi, S. M.↗
NASA NTRS2016

Attitude Control System Design for CubeSats Configured with Exo-Brake Parachute

This paper develops a novel attitude control strategy for an Earth orbiting CubeSat spacecraft by utilizing the exo-brake parachute to modulate the atmospheric drag forces as a source of attitude control authority, enabling orbital exo-sail maneuvers. In particular, the spacecraft attitude controls can be realized through the two dimensional exo-sail maneuvers in pitch and yaw directions. The uncertain atmospheric drag induced disturbance torque is estimated through an adaptive parameter estimation process which makes use of the adaptive least-squares minimization techniques. The covariance updating law with a variable forgetting factor is adopted and it can be shown that the convergent rate for the estimation errors can be chosen at the same level as the forgetting factor, in order to meet the design needs. The proposed approach is best suited for Earth orbiting micronano-satellite applications, which are configured with exo-brake parachute. With integration of exo-sail actuation mechanism and disturbance estimation, we demonstrate through simulations that exo-sail induced control torque for CubeSat attitude maneuver is feasible.

Disturbance estimation↗
NASA NTRS2005

Ball Bearings Equipped for In Situ Lubrication on Demand

In situ systems that provide fresh lubricants to ball/race contacts on demand have been developed to prolong the operational lives of ball bearings. These systems were originally intended to be incorporated into ball bearings in mechanisms that are required to operate in outer space for years, in conditions in which lubricants tend to deteriorate and/or evaporate. These systems may also be useful for similarly prolonging bearing lifetimes on Earth. Reservoirs have been among the means used previously to resupply lubricants. Lubricant- resupply reservoirs are bulky and add complexity to bearing assemblies. In addition, such a reservoir cannot be turned on or off as needed: it supplies lubricant continuously, often leading to an excess of lubricant in the bearing. A lubricator of the present type includes a porous ring cartridge attached to the inner or the outer ring of a ball bearing (see Figure 1). Oil is stored in the porous cartridge and is released by heating the cartridge: Because the thermal expansion of the oil exceeds that of the cartridge, heating causes the ejection of some oil. A metal film can be deposited on a face of the cartridge to serve as an electrical-resistance heater. The heater can be activated in response to a measured increase in torque that signals depletion of oil from the bearing/race contacts. Because the oil has low surface tension and readily wets the bearing-ring material, it spreads over the bearing ring and eventually reaches the ball/race contacts. The Marangoni effect (a surface-tension gradient associated with a temperature gradient) is utilized to enhance the desired transfer of lubricant to the ball/race contacts during heating. For a test, a ball bearing designed for use at low speed was assembled without lubricant and equipped with a porous-ring lubricator, the resistance heater of which consumed a power of less than 1 W when triggered on by a torque-measuring device. In the test, a load of 20 lb (.89 N) was applied and the bearing was turned at a rate of 200 RPM. The lubricator control was turned on at the beginning of the test, turned off for about 800 seconds, then turned on again. As shown in Figure 2, the controlled lubricator stabilized the torque in a low range, starting immediately after initial turn-on and immediately after resumption of the lubricator control.

Marchetti, Mario↗
NASA NTRS2011

Miniature, Variable-Speed Control Moment Gyroscope

The Miniature Variable-Speed Control Moment Gyroscope (MVS-CMG) was designed for small satellites (mass from less than 1 kg up to 500 kg). Currently available CMGs are too large and heavy, and available miniature CMGs do not provide sufficient control authority for use on practical satellites. This primarily results from the need to greatly increase the speed of rotation of the flywheel in order to reduce the flywheel size and mass. This goal was achieved by making use of a proprietary, space-qualified, high-speed (100,000 rpm) motor technology to spin the flywheel at a speed ten times faster than other known miniature CMGs under development. NASA is supporting innovations in propulsion, power, and guidance and navigation systems for low-cost small spacecraft. One of the key enabling technologies is attitude control mechanisms. CMGs are particularly attractive for spacecraft attitude control since they can achieve higher torques with lower mass and power than reaction wheels, and they provide continuous torque capability that enables precision pointing (in contrast to on-off thruster control). The aim of this work was to develop a miniature, variable-speed CMG that is sized for use on small satellites. To achieve improved agility, these spacecraft must be able to slew at high rate, which requires attitude control actuators that can apply torques on the order of 5 N-m. The MVS-CMG is specifically designed to achieve a high-torque output with a minimum flywheel and system mass. The flywheel can be run over a wide range of speeds, which is important to help reduce/eliminate potential gimbal lock, and can be used to optimize the operational envelope of the CMG.

Bilski, Steve↗
NASA NTRS1984

Elimination of uncontrollable rigid body mode, appendix C

The planar system model is examined which reveals two rigid body modes. One is due to the pure translation of the whole experiment assembly and is uncontrollable because the only control input is a torque at the gimbal. The other rigid body mode is due to the pointing of the gimbal and is the one for which control is sort. The problem arises from the Vector V2 which relates the control input to the modal coordinates. Since its fifth and sixth elements are both nonzero, neither body mode can be thrown away as is. The two rigid body modes must be transformed so that one is unaffected by the control input and one is left controllable. The uncontrollable mode can then be eliminated from the model for design purposes. A process is described to accomplish the elimination of the uncontrollable rigid body mode.

Source record↗
NASA NTRS2010

Compact, Lightweight Servo-Controllable Brakes

Compact, lightweight servo-controllable brakes capable of high torques are being developed for incorporation into robot joints. A brake of this type is based partly on the capstan effect of tension elements. In a brake of the type under development, a controllable intermediate state of torque is reached through on/off switching at a high frequency.

Lovchik, Christopher S.↗
NASA NTRS1973

Analysis of the computed torque drive method and comparison with conventional position servo for a computer-controlled manipulator

A manipulator and its control system (modeled after a Stanford design) is being developed as part of an artificial intelligence project. This development includes an analytical study of the control system software. A comparison is presented of the computed torque method and the conventional position servo. No conclusion is made as to the perference of one system over the other, as it is dependent upon the application and the results of a sampled data analysis.

Markiewicz, B. R.↗
NASA NTRS2018

Cassini’s Grand Finale – Attitude Control Subsystem Performance During Proximal Ring Plane Crossings

On April 22nd, 2017, the Cassini spacecraft made its final close targeted flyby of Titan, placing Cassini in the gap between Saturn and its innermost D-ring for the first time ever of its mission at Saturn. Cassini proceeded to fly through this region 22 times, and on September 15th, 2017, Cassini plunged into Saturn’s atmosphere, concluding a remarkable, nearly 20-year mission. The attitude control subsystem performance during these 22 “proximal” orbits exceeded expectations. Prior to the proximal orbits mission, the effects of dust hazards, Saturn atmospheric drag torque on Cassini’s control authority, radiation on the sensitive instruments, bright body interferences to the star tracker, pointing discrepancies caused by trajectory deviations, and possible fault protection scenarios were assessed. This paper discusses the results of these risks experienced by the attitude control subsystem over the proximal orbits mission, any interesting telemetry observed, as well as any last minute procedural changes implemented along the way.

Sung, Tina S.↗
NASA NTRS2015

Iodine Satellite

This project is a collaborative effort to mature an iodine propulsion system while reducing risk and increasing fidelity of a technology demonstration mission concept. 1 The FY 2014 tasks include investments leveraged throughout NASA, from multiple mission directorates, as a partnership with NASA Glenn Research Center (GRC), a NASA Marshall Space Flight Center (MSFC) Technology Investment Project, and an Air Force partnership. Propulsion technology is often a critical enabling technology for space missions. NASA is investing in technologies to enable high value missions with very small and low-cost spacecraft, even CubeSats. However, these small spacecraft currently lack any appreciable propulsion capability. CubeSats are typically deployed and drift without any ability to transfer to higher value orbits, perform orbit maintenance, or deorbit. However, the iodine Hall system can allow the spacecraft to transfer into a higher value science orbit. The iodine satellite (iSAT) will be able to achieve a (Delta)V of >500 m/s with <1 kg of solid iodine propellant, which can be stored in an unpressurized benign state prior to launch. The iSAT propulsion system consists of the 200 W Hall thruster, solid iodine propellant tank, a power processing unit, and the necessary valves and tubing to route the iodine vapor. The propulsion system is led by GRC, with critical hardware provided by the Busek Co. The propellant tank begins with solid iodine unpressurized on the ground and in-flight before operations, which is then heated via tank heaters to a temperature at which solid iodine sublimates to iodine vapor. The vapor is then routed through tubing and custom valves to control mass flow to the thruster and cathode assembly. 2 The thruster then ionizes the vapor and accelerates it via magnetic and electrostatic fields, resulting in thrust with a specific impulse >1,300 s. The iSAT spacecraft, illustrated in figure 1, is currently a 12U CubeSat. The spacecraft chassis will be constructed from aluminum with a finish to prevent iodine-driven corrosion. The iSAT spacecraft includes full three-axis control using wheels, magnetic torque rods, inertial management unit, and a suite of sensors and optics. The spacecraft will leverage heat generated by spacecraft components and radiators for a passive thermal control system.

Dankanich, John↗