Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “timing error evaluation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Implementation of Active Thermal Control (ATC) for the Soil Moisture Active and Passive (SMAP) Radiometer

NASA's Earth Observing Soil Moisture Active and Passive (SMAP) Mission is scheduled to launch in November 2014 into a 685 kilometer near-polar, sun-synchronous orbit. SMAP will provide comprehensive global mapping measurements of soil moisture and freeze/thaw state in order to enhance understanding of the processes that link the water, energy, and carbon cycles. The primary objectives of SMAP are to improve worldwide weather and flood forecasting, enhance climate prediction, and refine drought and agriculture monitoring during its three year mission. The SMAP instrument architecture incorporates an L-band radar and an L-band radiometer which share a common feed horn and parabolic mesh reflector. The instrument rotates about the nadir axis at approximately 15 revolutions per minute, thereby providing a conically scanning wide swath antenna beam that is capable of achieving global coverage within three days. In order to make the necessary precise surface emission measurements from space, the electronics and hardware associated with the radiometer must meet tight short-term (instantaneous and orbital) and long-term (monthly and mission) thermal stabilities. Maintaining these tight thermal stabilities is quite challenging because the sensitive electronics are located on a fast spinning platform that can either be in full sunlight or total eclipse, thus exposing them to a highly transient environment. A passive design approach was first adopted early in the design cycle as a low-cost solution. With careful thermal design efforts to cocoon and protect all sensitive components, all stability requirements were met passively. Active thermal control (ATC) was later added after the instrument Preliminary Design Review (PDR) to mitigate the threat of undetected gain glitches, not for thermal-stability reasons. Gain glitches are common problems with radiometers during missions, and one simple way to avoid gain glitches is to use the in-flight set point programmability that ATC affords to operate the radiometer component away from the problematic temperature zone. A simple ThermXL model (10 nodes) was developed to exercise quick trade studies among various proposed control algorithms: Modified P control vs. PI control. The ThermXL results were then compared with the detailed Thermal Desktop (TD) model for corroboration. Once done, the simple ThermXL model was used to evaluate parameter effects such as temperature digitization, heater size and gain margin, time step, and voltage variation of power supply on the ATC performance. A Modified P control algorithm was implemented into the instrument flight electronics based on the ThermXL results. The thermal short-term stability margin decreased by 10 percent with ATC and a wide temperature error band (plus or minus 0.1 degrees Centigrade) compared to the original passive thermal design. However, a tighter temperature error band (plus or minus 0.1 degrees Centigrade) increased the thermal short-term stability margin by a factor of three over the passive thermal design. The current ATC design provides robust thermal control, tighter stability, and greater in-flight flexibility even though its implementation was prompted by non-thermal performance concerns.

Mikhaylov, Rebecca↗
NASA NTRS2015

Towards the 1 mm/y Stability of the Radial Orbit Error at Regional Scales

An estimated orbit error budget for the Jason-1 and Jason-2 GDR-D solutions is constructed, using several measures of orbit error. The focus is on the long-term stability of the orbit time series for mean sea level applications on a regional scale. We discuss various issues related to the assessment of radial orbit error trends; in particular this study reviews orbit errors dependent on the tracking technique, with an aim to monitoring the long-term stability of all available tracking systems operating on Jason-1 and Jason-2 (GPS, DORIS, SLR). The reference frame accuracy and its effect on Jason orbit is assessed. We also examine the impact of analysis method on the inference of Geographically Correlated Errors as well as the significance of estimated radial orbit error trends versus the time span of the analysis. Thus a long-term error budget of the 10-year Jason-1 and Envisat GDR-D orbit time series is provided for two time scales: interannual and decadal. As the temporal variations of the geopotential remain one of the primary limitations in the Precision Orbit Determination modeling, the overall accuracy of the Jason-1 and Jason-2 GDR-D solutions is evaluated through comparison with external orbits based on different time-variable gravity models. This contribution is limited to an East-West "order-1" pattern at the 2 mm/y level (secular) and 4 mm level (seasonal), over the Jason-2 lifetime. The possibility of achieving sub-mm/y radial orbit stability over interannual and decadal periods at regional scales and the challenge of evaluating such an improvement using in situ independent data is discussed.

Precision Orbit Determination (POD)↗
NASA NTRSDate not supplied

A Survey Protocol to Assess Meaningfulness and Usefulness of Automated Topic Finding in the NASA Aviation Safety Reporting System

Context: The NASA Aviation Safety Reporting System (ASRS) is a voluntary confidential aviation safety reporting system. The ASRS receives reports from pilots, air traffic controllers, flight attendants and other involved in aviation operations. The reports are de-identified and coded by ASRS expert safety analysts and a short descriptive synopsis is written to describe the safety issue. The de-identified reports are then disseminated to the aviation community in a number of ways including entry into an online database, Safety Alert Bulletins and For Your Information Notices, and the CALLBACK newsletter. Key to these publications are the timely processing (de-identification, coding and summarization) of new reports, which is currently done by ASRS expert safety analysts. Thus, we believe topic modelling could decrease effort in ASRS, if topics are comprehensible. Aim: We propose a methodology to evaluate whether automated topic finding using topic modelling provides meaningful and useful topics. Method: We extend the total error survey methodology to evaluate user topic comprehension of machine learning outputs. To accomplish this we performed a literature review to identify existing methods and define a construct for topic comprehension, utilizing existing ASRS synopsis writing practices to more precisely define meaningfulness and usefulness. Results: A survey protocol was created that addresses the limitations of other survey protocols found in the literature review, which we found lacking in rationale and clear protocol definition. Conclusion: The surveying of user understanding in machine learning outputs presents challenges due to the explosion of parameters to control for and the lack of systematic approach presented in the literature. More reproducible work and survey protocols are needed in the literature and our work is one step towards that direction.

topic finding↗
NASA NTRS2001

Flying the TRMM Satellite in a GCM

By incorporating the Tropical Rainfall Measurement Mission (TRMM) satellite orbital information into the Colorado State University General Circulation Model (CSU GCM), we are able to 'fly' a satellite in the GCM, and sample the simulated atmosphere in the same way as the TRMM sensors sample the real atmosphere. The TRMM-sampled statistics for precipitation and radiative fluxes at annual, intraseasonal, monthly-mean and seasonal-mean diurnal time scales are evaluated by comparing the satellite-sampled against fully-sampled simulated atmospheres. The sampling rates of the TRMM sensors are significantly affected by the sensors' swath widths. The TRMM Microwave Imager (TMI) and the Visible Infrared Scanner (VIRS) sample each 2.25 x 2.25 degree grid box in the Tropics and subtropics about once per day, but at a different local time every day, while the Precipitation Radar (PR) and the Clouds and the Earth's Radiant Energy System (CERES) sensor visit each grid box about once every three days and twice per day, respectively. Besides inadequate samplings resulting from sensors' swath widths, there is a large, systematic diurnal undersampling associated with TRMM's orbital geometry for grid boxes away from the Equator. When only one month of TRMM data are used, this diurnal undersampling can lead to more daytime samples relative to nighttime samples in one hemisphere, and more nighttime samples relative to daytime samples in the other hemisphere. The resulting sampling biases (3-6 W m(exp-2)) are very pronounced in outgoing longwave radiation (OLR) over the subtropical land masses. The sampling errors in OLR monthly- and seasonal-means are less than 8 W m(exp-2) (5%) for each 2.25 x 2.25 degree grid box. The OLR monthly- and seasonal-means are not sensitive to diurnal undersamplings associated with the TRMM orbits and sensors' swath widths. However, this is not the case for total precipitation. Diurnal undersampling could produce errors as large as 20% in the Tropics and 40% in the subtropics, for the zonally averaged monthly-mean rain rates. The TRMM orbits sample each 2.25 x 2.25 degree grid box in the Tropics and subtropics 1-6 times for each hour of the day within a single season. The seasonal-mean diurnal cycles of precipitation and OLR are not well sampled for any one grid box. By either accumulating the satellite data for a long enough period, or averaging the data over a large area with a relatively uniform diurnal signal, the diurnal cycles of precipitation and OLR can be satisfactorily sampled. The effects TRMM sampling errors on the inferred tropical-mean hydrologic cycle and radiative fluxes are also evaluated. There are strong spurious oscillations associated with TRMM's orbital geometry, with periods of 23 days and 3-4 months, in tropical-mean daily and monthly precipitation. While the relative fluctuations of the sampled-OLR are negligible, the relative fluctuations of the sampled precipitation have magnitudes similar to those of the observed climate variability. Caution must therefore be used when applying TRMM observations of tropical-mean precipitation to interpret climate variations at intraseasonal and interannual scales.

Lin, Xin↗
NASA NTRS2024

Evaluation of Machine Learning and Deep Learning Algorithms for Fire Prediction in Southeast Asia

Vegetation fires are prevalent in South/Southeast Asian countries, making fire prediction crucial due to their potential environmental, economic, and social impacts. Accurate predictions of fires facilitate timely interventions, helping to mitigate uncontrolled fires that can lead to biodiversity loss and air quality issues. In this study, we utilize VIIRS satellite-derived fire data alongside six machine learning and deep learning models—Simple Persistence, Multi-Layer Perceptron (MLP), Convolutional Neural Network (CNN), Long Short-Term Memory (LSTM), CNN-LSTM, and ConvLSTM—to determine the most effective fire prediction model, using Root Mean Square Error (RMSE) as the metric. Our results indicate that the CNN model is the most reliable in regions with spatial dependencies, such as Brunei, Indonesia, Malaysia, the Philippines, Timor-Leste, and Thailand. Conversely, the ConvLSTM model excels in countries with complex spatiotemporal dynamics like Laos, Myanmar, and Vietnam. The CNN-LSTM hybrid model also performed well in Cambodia, suggesting a need for a balanced approach in areas requiring both spatial and temporal feature extraction. Furthermore, simpler models like Persistence and MLP showed limitations in capturing dynamic patterns and temporal dependencies. Our findings highlight the importance of evaluating models before implementing any decision support systems (DSS) in fire management. By tailoring models to specific regional fire data, we can enhance prediction accuracy and responsiveness, ultimately improving fire risk management in Southeast Asia and beyond.

Deep learning↗
NASA NTRS2000

Evaluation of the Applicability of Solar and Lamp Radiometric Calibrations of a Precision Sun Photometer Operating Between 300 and 1025 nm

Over a period of 3 year a precision Sun photometer (SPM) operating between 300 and 1025 nm was calibrated four times at three different high-mountain sites in Switzerland, Germany, and the United States by means of the Langley-plot technique. We found that for atmospheric window wavelengths the total error (2 sigma-statistical plus systematic errors) of the calibration constants V(sub 0)(lambda), the SPM voltage in the absence of any attenuating atmosphere, can be kept below 1.60% in the UV-A and blue, 0.9% in the mid-visible, and 0.6% in the near-infra red spectral region. For SPM channels within strong water-vapor or ozone absorption bands a modified Langley-plot technique was used to determine V(sub 0)(lambda) with a lower accuracy. Within the same period of time, we calibrated the SPM five times using irradiance standard lamps in the optical labs of the Physikalisch-Meteorologisches Observatorium Davos and World Radiation Center, Switzerland, and of the Remote Sensing Group of the Optical Sciences Center, University of Arizona, Tucson, Arizona. The lab calibration method requires knowledge of the extraterrestrial spectral irradiance. When we refer the standard lamp results to the World Radiation Center extraterrestrial solar irradiance spectrum, they agree with the Langley results within 2% at 6 or 13 SPM wavelengths. The largest disagreement (4.4%) is found for the channel centered at 610 nm. The results of these intercomparisons change significantly when the lamp results are referred to two different extraterrestrial solar irradiance spectra that have become recently available.

Schmid, Beat↗
NASA NTRS1991

Suppression of biodynamic interference in head-tracked teleoperation

The utility of helmet-tracked sights to provide pointing commands for teleoperation of cameras, lasers, or antennas in aircraft is degraded by the presence of uncommanded, involuntary heat motion, referred to as biodynamic interference. This interference limits the achievable precision required in pointing tasks. The noise contributions due to biodynamic interference consists of an additive component which is correlated with aircraft vibration and an uncorrelated, nonadditive component, referred to as remnant. An experimental simulation study is described which investigated the improvements achievable in pointing and tracking precision using dynamic display shifting in the helmet-mounted display. The experiment was conducted in a six degree of freedom motion base simulator with an emulated helmet-mounted display. Highly experienced pilot subjects performed precision head-pointing tasks while manually flying a visual flight-path tracking task. Four schemes using adaptive and low-pass filtering of the head motion were evaluated to determine their effects on task performance and pilot workload in the presence of whole-body vibration characteristic of helicopter flight. The results indicate that, for tracking tasks involving continuously moving targets, improvements of up to 70 percent can be achieved in percent on-target dwelling time and of up to 35 percent in rms tracking error, with the adaptive plus low-pass filter configuration. The results with the same filter configuration for the task of capturing randomly-positioned, stationary targets show an increase of up to 340 percent in the number of targets captured and an improvement of up to 24 percent in the average capture time. The adaptive plus low-pass filter combination was considered to exhibit the best overall display dynamics by each of the subjects.

Lifshitz, S.↗
NASA NTRS2015

Enabling Performance-Based Navigation Arrivals: Development and Simulation Testing of the Terminal Sequencing and Spacing System

NASA has developed an advanced arrival management capability for terminal controllers, known as Terminal Sequencing and Spacing (TSS). TSS increases use of performance-based navigation (PBN) arrival procedures during periods of high traffic demand. It extends two Federal Aviation Administration's operational systems with terminal metering and controller spacing tools. Sixteen high-fidelity human-in-the-loop simulations, involving more than five hundred hours of evaluation time, were conducted to mature TSS from proof-of- concept design to fully functional prototype. These simulations modeled arrival procedures at several U.S. airports, incorporated a broad range of traffic demand profiles and wind conditions, and used controllers with extensive operational experience. Two fundamental metrics are evaluated for these simulations: PBN Success Rate and Inter-Arrival Spacing Error. The PBN Success Rate shows a definitive trend when TSS is used. It increases from 42 percent for today's operations to 68 percent for terminal metering only and 92 percent for terminal metering with controller-managed spacing tools. Meanwhile, the Inter-Arrival Spacing Error improves 25 to 35 percent when TSS is used compared to not used. The TSS technology was transferred to the FAA and, and it is targeted for deployment to several busy airports in the U.S. starting in 2018.

terminal metering↗
NASA NTRS2007

Modeling and Parameter Estimation of Spacecraft Fuel Slosh with Diaphragms Using Pendulum Analogs

Prediction and control of liquid slosh in moving containers is an important consideration in the design of spacecraft and launch vehicle control systems. Even with modern computing systems, CFD type simulations are not fast enough to allow for large scale Monte Carlo analyses of spacecraft and launch vehicle dynamic behavior with slosh included. It is still desirable to use some type of simplified mechanical analog for the slosh to shorten computation time. Analytic determination of the slosh analog parameters has met with mixed success and is made even more difficult by the introduction of propellant management devices such as elastomeric diaphragms. By subjecting full-sized fuel tanks with actual flight fuel loads to motion similar to that experienced in flight and measuring the forces experienced by the tanks, these parameters can be determined experimentally. Currently, the identification of the model parameters is a laborious trial-and-error process in which the hand-derived equations of motion for the mechanical analog are evaluated and their results compared with the experimental results. This paper will describe efforts by the university component of a team comprised of NASA's Launch Services Program, Embry Riddle Aeronautical University, Southwest Research Institute and Hubert Astronautics to improve the accuracy and efficiency of modeling techniques used to predict these types of motions. Of particular interest is the effect of diaphragms and bladders on the slosh dynamics and how best to model these devices. The previous research was an effort to automate the process of slosh model parameter identification using a MATLAB/SimMechanics-based computer simulation. These results are the first step in applying the same computer estimation to a full-size tank and vehicle propulsion system. The introduction of diaphragms to this experimental set-up will aid in a better and more complete prediction of fuel slosh characteristics and behavior. Automating the parameter identification process will save time and thus allow earlier identification of potential vehicle performance problems.

Chatman, Yadira↗
NASA NTRS1972

Hybrid and concatenated coding applications.

Results of a study to evaluate the performance and implementation complexity of a concatenated and a hybrid coding system for moderate-speed deep-space applications. It is shown that with a total complexity of less than three times that of the basic Viterbi decoder, concatenated coding improves a constraint length 8 rate 1/3 Viterbi decoding system by 1.1 and 2.6 dB at bit error probabilities of 0.0001 and one hundred millionth, respectively. With a somewhat greater total complexity, the hybrid coding system is shown to obtain a 0.9-dB computational performance improvement over the basic rate 1/3 sequential decoding system. Although substantial, these complexities are much less than those required to achieve the same performances with more complex Viterbi or sequential decoder systems.

Hofman, L. B.↗
NASA NTRS1978

Man/terminal interaction evaluation of computer operating system command and control service concepts

The Experiment Computer Operating System (ECOS) of the Spacelab will allow the onboard Payload Specialist to command experiment devices and display information relative to the performance of experiments. Three candidate ECOS command and control service concepts were reviewed and laboratory data on operator performance was taken for each concept. The command and control service concepts evaluated included a dedicated operator's menu display from which all command inputs were issued, a dedicated command key concept with which command inputs could be issued from any display, and a multi-display concept in which command inputs were issued from several dedicated function displays. Advantages and disadvantages are discussed in terms of training, operational errors, task performance time, and subjective comments of system operators.

Dodson, D. W.↗
NASA NTRS1981

Boundary conditions for subsonic compressible Navier-Stokes calculations

A systematic study of inflow and outflow boundary conditions for the numerical solution of the compressible Navier-Stokes equations is presented. Combinations of several representative inflow and outflow boundary conditions are applied in the solution of subsonic flow over a flat plate in a finite computational domain. These boundary conditions are evaluated in terms of their effect on the accuracy of the solution and the rate of convergence to a steady state. It is shown that errors in the data specified at the inflow boundary can produce significant errors in the computed flow field. It is also shown that a non-reflecting outflow boundary condition can significantly reduce the total computational time required.

Rudy, D. H.↗
NASA NTRS1986

Impact of mismodeled idle engine performance on calculation and tracking of optimal 4-D descent trajectories

Advanced flight management systems are being developed which are capable of calculating optimal 3-D and 4-D flight trajectories for arbitrary fuel and time costs. These systems require mathematical models of airplane performance in order to compute the optimal profiles. Mismodeled idle engine characteristics can result in descent trajectories requiring excessive throttle and/or speedbrake activity in order to achieve the desired end conditions. This paper evaluates the cost and fuel penalties, trajectory variations, and flight control requirements associated with typical idle engine modeling errors for a twin-jet transport airplane. Variations in idle power setting, thrust, fuel flow, and surge bleed operation were evaluated for a cruise/descent flight segment. The results of this analysis provide insight into the penalties associated with uncertainties in idle engine performance and suggest methods of modeling which minimize these penalties.

Williams, D. H.↗
NASA NTRS1992

The effects of multiple aerospace environmental stressors on human performance

An extended Fitt's law paradigm reaction time (RT) task was used to evaluate the effects of acceleration on human performance in the Dynamic Environment Simulator (DES) at Armstrong Laboratory, Wright-Patterson AFB, Ohio. This effort was combined with an evaluation of the standard CSU-13 P anti-gravity suit versus three configurations of a 'retrograde inflation anti-G suit'. Results indicated that RT and error rates increased 17 percent and 14 percent respectively from baseline to the end of the simulated aerial combat maneuver and that the most common error was pressing too few buttons.

Popper, S. E.↗
NASA NTRS1998

TACT: A Set of MSC/PATRAN- and MSC/NASTRAN- based Modal Correlation Tools

This paper describes the functionality and demonstrates the utility of the Test Analysis Correlation Tools (TACT), a suite of MSC/PATRAN Command Language (PCL) tools which automate the process of correlating finite element models to modal survey test data. The initial release of TACT provides a basic yet complete set of tools for performing correlation totally inside the PATRAN/NASTRAN environment. Features include a step-by-step menu structure, pre-test accelerometer set evaluation and selection, analysis and test result export/import in Universal File Format, calculation of frequency percent difference and cross-orthogonality correlation results using NASTRAN, creation and manipulation of mode pairs, and five different ways of viewing synchronized animations of analysis and test modal results. For the PATRAN-based analyst, TACT eliminates the repetitive, time-consuming and error-prone steps associated with transferring finite element data to a third-party modal correlation package, which allows the analyst to spend more time on the more challenging task of model updating. The usefulness of this software is presented using a case history, the correlation for a NASA Langley Research Center (LaRC) low aspect ratio research wind tunnel model. To demonstrate the improvements that TACT offers the MSC/PATRAN- and MSC/DIASTRAN- based structural analysis community, a comparison of the modal correlation process using TACT within PATRAN versus external third-party modal correlation packages is presented.

Marlowe, Jill M.↗
NASA NTRS1998

Design, Evaluation and GCM-Performance of a New Parameterization for Microphysics of Clouds with Relaxed Arakawa-Schubert Scheme (McRas)

A prognostic cloud scheme named McRAS (Microphysics of clouds with Relaxed Arakawa-Schubert Scheme) was developed with the aim of improving cloud-microphysics, and cloud-radiation interactions in GCMs. McRAS distinguishes convective, stratiform, and boundary-layer clouds. The convective clouds merge into stratiform clouds on an hourly time-scale, while the boundary-layer clouds do so instantly. The cloud condensate transforms into precipitation following the auto-conversion relations of Sundqvist that contain a parametric adaptation for the Bergeron-Findeisen process of ice crystal growth and collection of cloud condensate by precipitation. All clouds convect, advect, and diffuse both horizontally and vertically with a fully active cloud-microphysics throughout its life-cycle, while the optical properties of clouds are derived from the statistical distribution of hydrometeors and idealized cloud geometry. An evaluation of McRAS in a single column model (SCM) with the GATE Phase III data has shown that McRAS can simulate the observed temperature, humidity, and precipitation without discernible systematic errors. An evaluation with the ARM-CART SCM data in a cloud model intercomparison exercise shows reasonable but not an outstanding accurate simulation. Such a discrepancy is common to almost all models and is related, in part, to the input data quality. McRAS was implemented in the GEOS II GCM. A 50 month integration that was initialized with the ECMWF analysis of observations for January 1, 1987 and forced with the observed sea-surface temperatures and sea-ice distribution and vegetation properties (biomes, and soils), with prognostic soil moisture, snow-cover, and hydrology showed a very realistic simulation of cloud process, incloud water and ice, and cloud-radiative forcing (CRF). The simulated ITCZ showed a realistic time-mean structure and seasonal cycle, while the simulated CRF showed sensitivity to vertical distribution of cloud water which can be easily altered by the choice of time constant and incloud critical cloud water amount regulators for auto-conversion. The CRF and its feedbacks also have a profound effect on the ITCZ. Even though somewhat weaker than observed, the McRAS-GCM simulation produces robust 30-60 day oscillations in the 200 hPa velocity potential. Two ensembles of 4-summer (July, August, September) simulations, one each for 1987 and 1988 show that the McRAS-GCM simulates realistic and statistically significant precipitation differences over India, Central America, and tropical Africa. Several seasonal simulations were performed with McRAS-GEOS II GCM for the summer (June-July- August) and winter (December-January-February) periods to determine how the simulated clouds and CRFs would be affected by: i) advection of clouds; ii) cloud top entrainment instability, iii) cloud water inhomogeneity correction, and (iv) cloud production and dissipation in different cloud-processes. The results show that each of these processes contributes to the simulated cloud-fraction and CRF.

Sud, Y. C.↗
NASA NTRS1974

Multi-off-grid methods in multi-step integration of ordinary differential equations

Description of methods of solving first- and second-order systems of differential equations in which all derivatives are evaluated at off-grid locations in order to circumvent the Dahlquist stability limitation on the order of on-grid methods. The proposed multi-off-grid methods require off-grid state predictors for the evaluation of the n derivatives at each step. Progressing forward in time, the off-grid states are predicted using a linear combination of back on-grid state values and off-grid derivative evaluations. A comparison is made between the proposed multi-off-grid methods and the corresponding Adams and Cowell on-grid integration techniques in integrating systems of ordinary differential equations, showing a significant reduction in the error at larger step sizes in the case of the multi-off-grid integrator.

Beaudet, P. R.↗
NASA NTRS2009

An Empirical Approach to Ocean Color Data: Reducing Bias and the Need for Post-Launch Radiometric Re-Calibration

A new empirical approach is developed for ocean color remote sensing. Called the Empirical Satellite Radiance-In situ Data (ESRID) algorithm, the approach uses relationships between satellite water-leaving radiances and in situ data after full processing, i.e., at Level-3, to improve estimates of surface variables while relaxing requirements on post-launch radiometric re-calibration. The approach is evaluated using SeaWiFS chlorophyll, which is the longest time series of the most widely used ocean color geophysical product. The results suggest that ESRID 1) drastically reduces the bias of ocean chlorophyll, most impressively in coastal regions, 2) modestly improves the uncertainty, and 3) reduces the sensitivity of global annual median chlorophyll to changes in radiometric re-calibration. Simulated calibration errors of 1% or less produce small changes in global median chlorophyll (less than 2.7%). In contrast, the standard NASA algorithm set is highly sensitive to radiometric calibration: similar 1% calibration errors produce changes in global median chlorophyll up to nearly 25%. We show that 0.1% radiometric calibration error (about 1% in water-leaving radiance) is needed to prevent radiometric calibration errors from changing global annual median chlorophyll more than the maximum interannual variability observed in the SeaWiFS 9-year record (+/- 3%), using the standard method. This is much more stringent than the goal for SeaWiFS of 5% uncertainty for water leaving radiance. The results suggest ocean color programs might consider less emphasis of expensive efforts to improve post-launch radiometric re-calibration in favor of increased efforts to characterize in situ observations of ocean surface geophysical products. Although the results here are focused on chlorophyll, in principle the approach described by ESRID can be applied to any surface variable potentially observable by visible remote sensing.

Gregg, Watson W.↗