Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thick electrode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Universal Relationship between Limiting Current and Electrochemical Transport Properties in Malonate-Based Polymer Electrolytes

There is considerable interest in developing high-performance electrolytes for rechargeable lithium batteries. For practical applications, the electrolyte must support large dc currents. However, the parameters most often reported in the literature, conductivity, κ, and current fraction, ρ + , reflect ion transport in the limit of infinitesimal currents. In this limit, the efficacy of an electrolyte is given by the product κρ + . The limiting current density, i lim , is the maximum current density that can be applied across an electrolyte; the cell voltage diverges if the applied current density exceeds ilim. This parameter reflects ion transport in the limit of large dc currents and is therefore of practical interest. It would therefore be convenient if i lim could be predicted from measurements of κρ + . In order to explore this possibility, we studied six malonate-based polymers and PEO at a fixed salt concentration (r = 0.08) and temperature (90°C) using symmetric cells with planar electrodes. Unfortunately, there is no correlation between ilim and κρ + . When the applied current density, i, is less than ilim, the cell voltage approaches a stable plateau, ϕ plateau . Here, we found a linear dependence between i and thickness-normalized plateau potential, ϕ plateau L –1 , irrespective of the magnitude of the applied current. In all seven polymer electrolytes, we found a linear correlation between ilim and the slopes of these lines, σ. In other words, measurements of σ can be used to predict the limiting current.

Jana, Rounak [Lawrence Berkeley National Laborator↗
DOE OSTI2025

An Active Oxygen Electrode for Proton-Conducting Solid Oxide Electrolysis Cells with High Faradaic Efficiency

Addressing the challenges posed by inferior electrochemical performance at low temperatures and the uncertain Faradaic efficiency (FE) represents a pivotal undertaking in the development of high performance and efficient proton-conducting solid oxide electrolysis cells (P-SOECs). In this work, a novel oxygen electrode material BaCo0.8Zr0.1Zn0.1O3-d (BCZZ) is first designed and synthesized. At 600 °C, P-SOECs with BCZZ oxygen electrode achieve an electrolysis current density of 1.98 A cm-2 with an ˜90% FE at 1.3 V. Utilizing 1-inch P-SOECs as a reliable platform, the effect of extrinsic operating conditions (i.e., steam concentration, voltage, current density, and temperature) and intrinsic properties of P-SOECs (i.e., electrolyte material and electrolyte thickness) on FE are further systemically investigated, both experimentally and theoretically.

08 - HYDROGEN↗
DOE OSTI2023

Carbon Coating Influence on the Formation of Percolating Electrode Networks for Silicon Anodes

Previous studies have demonstrated that chemical vapor deposition carbon coating on silicon (Si@C) can enhance the electrochemical performance of lithium-ion batteries with Si-based anodes. However, the underlying mechanisms contributing to this improvement have not been fully explored. Here, we address this knowledge gap by applying a suite of characterization methods to evaluate Si@C anodes prepared by reducing acetylene on ball-milled Si particles. Raman mapping measurements show that the C coating (<5 nm thick) enables a homogeneous Si and carbon distribution during the slurry casting process, thereby promoting Si utilization during cycling. The coating’s microstructure and morphology were evaluated using X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy, and neutron reflectivity experiments. Electrochemical impedance spectroscopy measurements upon cycling indicate that carbon coating also reduces the overall resistance as benchmarked against bare Si anodes. Galvanostatic cycling in half-cell studies revealed higher initial Coulombic efficiency and specific capacities with increasing carbon coating time. However, solid electrolyte interphase (SEI) investigations using XPS showed that the coated and uncoated samples have very similar characteristics, suggesting that the SEI may only play a minor role in enhancing the performance of Si@C. Full-cell evaluation of the Si electrodes was consistent with half-cell results relating to performance and SEI properties, further supporting the conclusion that electronic and ionic percolation, enabled by effective electrode manufacturing, are the dominant factors contributing to the favorable performance of Si@C.

25 ENERGY STORAGE↗
DOE OSTI2024

17.2% Efficient CdSexTe1−x solar cell with (InxGa1−x)2O3 emitter on lightweight and flexible glass

High-efficiency, lightweight, and flexible solar cells are sought for a variety of applications particularly when high power density and flexible form factors are desired. Development of solar cells on flexible substrates may also offer production advantages in roll-to-roll or sheet-to-sheet processes. Here, we report device efficiencies of 17.2% and 14.6%, under AM1.5G and AM0 irradiances, respectively, for a flexible, lightweight, CdTe-based solar cell. To advance the efficiency relative to the highest previously reported AM1.5G value of 16.4%, we used an indium gallium oxide (IGO) emitter layer on a cadmium stannate (CTO) transparent conductor, which was deposited on 100-μm thick Corning® Willow® Glass. A sputtered CdSe layer was employed to incorporate Se into a CdTe absorber that was deposited by close-space sublimation, and CuSCN was used as a hole transport layer between the CdTe and the back metal electrode. The IGO and CTO layers remained intact during the high temperature film processing as seen in cross-sectional imaging and elemental mapping. This device configuration offers great promise for building-integrated photovoltaics, space applications, and higher rate manufacturing.

Physics↗
DOE OSTI2024

Catalyst

Catalysts comprising a Ta layer having an outer layer with a layer comprising Pt directly thereon, wherein the Ta layer has an average thickness in a range from 0.04 to 30 nanometers, wherein the layer comprising Pt has an average thickness in a range from 0.04 to 50 nanometers, and wherein the Pt and Ta are present in an atomic ratio in a range from 0.01:1 to 10:1. Catalyst described herein are useful, for example, in fuel cell membrane electrode assemblies.

Steinbach, Andrew J. L.↗
DOE OSTI2023

Revealing the aging process of solid electrolyte interphase on SiOx anode

Abstract As one of the most promising alternatives to graphite negative electrodes, silicon oxide (SiO x ) has been hindered by its fast capacity fading. Solid electrolyte interphase (SEI) aging on silicon SiO x has been recognized as the most critical yet least understood facet. Herein, leveraging 3D focused ion beam-scanning electron microscopy (FIB-SEM) tomographic imaging, we reveal an exceptionally characteristic SEI microstructure with an incompact inner region and a dense outer region, which overturns the prevailing belief that SEIs are homogeneous structure and reveals the SEI evolution process. Through combining nanoprobe and electron energy loss spectroscopy (EELS), it is also discovered that the electronic conductivity of thick SEI relies on the percolation network within composed of conductive agents (e.g., carbon black particles), which are embedded into the SEI upon its growth. Therefore, the free growth of SEI will gradually attenuate this electron percolation network, thereby causing capacity decay of SiO x . Based on these findings, a proof-of-concept strategy is adopted to mechanically restrict the SEI growth via applying a confining layer on top of the electrode. Through shedding light on the fundamental understanding of SEI aging for SiO x anodes, this work could potentially inspire viable improving strategies in the future.

25 ENERGY STORAGE↗
DOE OSTI2022

Damage of prismatic lithium‐ion cells subject to bending: Test, model, and detection

Abstract The mechanically induced internal short circuit (ISC) is one of the major safety concerns of lithium‐ion batteries. Mechanical abuse tests are often performed to evaluate the integrity and safety of lithium‐ion batteries under mechanical loadings. Except for the widely explored compression‐dominated indentation tests, bending is another typical real‐world loading condition that is tension‐dominated. To investigate the mechanical damage and ISC behavior of batteries under bending, we carried out controlled three‐point bending tests in four progressive steps on prismatic battery cells with maximum deflections ranging from 38% to 76% of the cell thickness. None of the tested cells experienced an ISC. We then conducted 3D X‐ray computed tomography (CT) scanning on the bent cells after unloading. X‐ray CT images showed three out of the four tested cells have extensive cracking in the electrode layers at the bottom side (opposite to the loading head). This indicates that cracking does not necessarily lead to an ISC under bending. Electrochemical impedance spectroscopy was also measured on the bent cells and substantial changes were observed. Both the bulk resistance and charge‐transfer resistance increased significantly after bending, which could influence the battery performance and lifespan. We then developed a detailed finite (FE) element model to further investigate the mechanical deformation and failure mechanisms. The FE model successfully predicts the load–displacement response and reproduces the deformation patterns. The findings and the FE model developed in the present study provide useful insights and tools for the battery structure and crash safety design. image

25 ENERGY STORAGE↗
DOE OSTI2025

Amino Acid Sequence Controls Enhanced Electron Transport in Heme-Binding Peptide Monolayers

Metal-binding proteins have the exceptional ability to facilitate long-range electron transport in nature. Despite recent progress, the sequence-structure–function relationships governing electron transport in heme-binding peptides and protein assemblies are not yet fully understood. In this work, the electronic properties of a series of heme-binding peptides inspired by cytochrome bc1 are studied using a combination of molecular electronics experiments, molecular modeling, and simulation. Self-assembled monolayers (SAMs) are prepared using sequence-defined heme-binding peptides capable of forming helical secondary structures. Following monolayer formation, the structural properties and chemical composition of assembled peptides are determined using atomic force microscopy and X-ray photoelectron spectroscopy, and the electronic properties (current density–voltage response) are characterized using a soft contact liquid metal electrode method based on eutectic gallium–indium alloys (EGaIn). Our results show a substantial 1000-fold increase in current density across SAM junctions upon addition of heme compared to identical peptide sequences in the absence of heme, while maintaining a constant junction thickness. These findings show that amino acid composition and sequence directly control enhancements in electron transport in heme-binding peptides. Overall, this study demonstrates the potential of using sequence-defined synthetic peptides inspired by nature as functional bioelectronic materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Mitigating the Effects of Au-Al Intermetallic Compounds Due to High-Temperature Processing of Surface-Electrode Ion Traps

Stringent physical requirements need to be met for the high-performing surface-electrode ion traps used in quantum computing and timekeeping. In particular, these traps must survive a high-temperature environment for vacuum chamber preparation and support high RF voltage on closely spaced electrodes. Due to the use of gold wire bonds on aluminum pads, intermetallic growth can lead to wire bond failure via breakage or high resistance, limiting the lifetime of a trap assembly to a single multiday bake at 200 ° C. Using traditional thick metal stacks to prevent intermetallic growth, however, can result in trap failure due to RF breakdown events. Through high-temperature experiments, we conclude that an ideal metal stack for ion traps is Ti/Pt/Au (20/100/250 nm), which allows for a cumulative bakeable time of roughly 86 days without compromising the trap voltage performance. This increase in the bakeable lifetime of ion traps will remove the need to discard otherwise functional ion traps when vacuum hardware is upgraded, which will greatly benefit ion trap experiments.

Haltli, Raymond A.↗
DOE OSTI2022

Laser Doppler vibrometry for piezoelectric coefficient ($d_{33}$) measurements in irradiated aluminum nitride

Sensors used for experiments in advanced reactors must survive in harsh environments. Few material systems can be used to construct sensors viable for extreme conditions. Aluminum nitride (AlN) is one such material because it has high thermal stability and radiation resistance and sustains good piezoelectric and dielectric properties at high temperatures. In this work, the piezoelectric coefficient $d_{33}$ of the AlN single-crystal with thermal and irradiation damage was investigated using an indirect method with a laser Doppler vibrometer (LDV). Surface electrodes were deposited on the AlN samples, and the vibration response of the samples to an applied voltage was monitored using the LDV as a function of the excitation frequency. The $d_{33}$ estimation was based on the excitation voltage and the thickness-mode displacement extracted from the LDV measurements. Further, six AlN substrates were irradiated with 8 MeV Al 2+ at three fluences (10 15 , 10 16 , and 10 17 ions/cm 2 ) and two temperatures (300 °C and 500 °C). The $d_{33}$ for the six irradiated samples and one pristine sample were measured, and the measurement uncertainty was estimated based on five repeated tests. All samples were also measured by a commercial piezometer for comparison. The experimental results demonstrate that the piezoelectric coefficients obtained by LDV were about 0.8–1.16 pm/V lower than those obtained by the piezometer. With the compensation of the clamping effect, the corrected LDV values are similar to the piezometer results. Both show similar trends in all samples, which validates the feasibility of the proposed method for $d_{33}$ measurement. Based on the LDV results, the irradiated samples show a 12%–22% decrease in $d_{33}$ compared with the pristine samples. The samples irradiated under the same fluence at a higher temperature (500 °C) demonstrated a lower $d_{33}$ than those at 300 °C. The effect of the retro-reflective tape, sample temperature, and sample size on the $d_{33}$ measurement were also studied.

36 MATERIALS SCIENCE↗
DOE OSTI2025

One-Step Transfer of Symmetric and Asymmetric Contacts for Large-Scale 2D Electronics and Optoelectronics

Two-dimensional (2D) semiconductors are highly promising candidates for thin-film transistor applications due to their scalability, transferability, atomic thickness, and relatively high carrier mobility. However, a substantial performance gap remains between individual devices based on single-crystalline 2D films and wafer-scale integrated circuits, primarily due to defects introduced during conventional fabrication processes. Here, we report a diamond-assisted electrode transfer technique for the van der Waals integration of wafer-scale prefabricated electrode arrays onto 2D materials, enabling scalable electronics and optoelectronics. Implemented on metal–organic chemical vapor deposition-grown monolayer molybdenum disulfide, this method forms ultraclean metal–semiconductor interfaces, yielding field-effect transistors with excellent ohmic contacts, a low contact resistance of 400 Ω·μm, and a Schottky barrier height of only 9 meV. Furthermore, we demonstrate a scalable transistor array on monolayer molybdenum disulfide with excellent device performance uniformity, achieving an average field-effect mobility of 30 cm 2 V –1 s –1 and an on/off current ratio exceeding 105. Additionally, high photocurrent and responsivity were demonstrated in the array devices, showing their potential for excellent image detection. We further demonstrate the versatility of this technique by fabricating a Schottky diode array through a single-step transfer of asymmetric electrodes─low work function aluminum and high work function gold─onto monolayer tungsten diselenide. This approach provides a clean, effective solution for contact engineering in 2D materials, offering a viable pathway toward wafer-scale, high-performance 2D electronics, optoelectronics, and integrated circuits.

2D electronics↗
DOE OSTI2025

Microfluidic cells for the 1–10 2 MPa pressure range

Thin membrane-delimited fluid cells supporting up to 1 at (0.1 MPa) of pressure are well known and commercially available for use in vacuum chambers of electron, photon, or various particle beam microscopies or spectroscopies. Hereby, we report on the development of fluid cells capable of working at 1–10 MPa, extending the analysis domain for investigating chemical, biochemical, or physical processes at pressures of interest in chemical synthesis, underwater biochemistry studies or underground geology. We explored ways to optimize cell membranes to better resist pressure beyond simply increasing the thickness or decreasing the size of the membranes, using finite element analysis and experimental validation via membrane bulging experiments and failure statistics. Fluid cell prototypes were fabricated using ∼75 nm-thick SiN x membranes, engineered to withstand 4.7 MPa (average value), compared to regular (un-engineered) membranes withstanding only 3.4 MPa (average value). The fluid cell prototypes include eight microchannels for feeding/evacuating the fluids and applying pressure into micro-reaction chambers, two electrodes for electrochemical or conduction measurements in the sample, and a possible pressure or temperature sensor, customizable for specific experiments.

hi-pressure↗
DOE OSTI2023

Atomic layer deposition for surface area determination of solid oxide electrodes

Surface area measurements are important for characterizing porous solids, but commonly used methods such as Brunauer–Emmett–Teller (BET) gas adsorption and computed nanotomography are lacking for certain applications such as the development of solid oxide fuel cell electrodes, which often have absolute surface areas <1 m 2 and contain nanoscale features. Presented is a novel method for the surface area determination of samples with total measurable areas of 1–1000 cm 2 with a standard deviation ± 1 cm 2 , utilizing the atomic layer deposition (ALD) of Al 2 O 3 over microstructurally complex internal porosity. The volume of alumina is then quantified using plasma spectroscopy and converted to an area using the known ALD layer thickness. Under the modest ALD reactor soak times used (8.5 s), the precursor penetration depth is found to be ~50 μm, exceeding the requirement for uniformly coating SOFC functional layers. A model system, (La 0.8 Sr 0.2 ) 0.98 MnO 3–δ /Ce 0.9 Gd 0.1 O 1.95 (LSM/GDC) scaffolds of ~2.7 m 2 g –1 , was measured using the technique and compared against the BET method, and comparable results were obtained but with 1000 times less material needed. The technique is demonstrated for measurements in two example areas of active SOFC research: exsolved (Ni, Fe) nanoparticles on an Sr(Ti, Fe, Ni)O 3–δ electrode and PrO x catalyst nanoparticles infiltrated onto LSM/GDC scaffolds. Finally, the technique may be broadly useful wherever the accurate surface area determination of small absolute quantities of porous ceramic structures on the order of 0.1–50 m 2 g –1 is sought.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Development of Nanocomposite Coatings for Future Large-Scale Time Projection Chambers

In the context of this award we tested the performance of thin high-resistivity coatings for their potential usage as field shaping systems in future large scale xenon Time Projection Chambers (TPC). A successful implementation of such thin coatings would likely simplify the design of potential future detectors, allowing to overcome some of the challenges observed with traditional systems constituted by massive discrete electrodes. We studied a wide range of materials and characterized their optical and electrical performances as functions of temperature and wavelength. The measurement campaign indicated that uniform coatings covering the full PTFE substrate (usually used as reflector in LXe TPCs) impact too severely on the light collection performance of such detectors when used with deep UV light. Despite tuning the composition and thicknesses of nanocomposite coatings, we were not able to identify a single coating, properly working at LXe temperature, that would simultaneously fulfill the resistance and optical requirements. Following the risk mitigation strategy identified in the proposal we moved the focus of the R&D to identify proper materials that, when coated with grid-like patterns on PTFE, would not alter meaningfully its optical properties (with respect to bare PTFE panels) but would still serve as effective field shaping systems, properly containing the drift field in TPC detectors. Among the various materials we identified germanium as the most promising one, providing a good adhesion to PTFE and the proper range of sheet resistivity. The Ge-patterned coating tested within a small scale LXe TPC showed good performance as a field shape system and, as desired, did not reduce the detector light yield. These results are encouraging and such technology should further be investigated as a potential alternative to more traditional field shaping electrodes. Incidentally, in the context of this R&D, we stumbled upon an unexpected behavior suggesting that some of the treatments performed on the PTFE panels, in preparation of the coatings, meaningfully boosted the PTFE reflectivity. The most probable candidate is the O2 plasma cleaning procedure. This hypothesis will be tested in the near future by operating the small scale TPC at UChicago first with regular PTFE panels and then with panels bombarded with O2 plasma (but no coatings). This finding, if confirmed, might open up the possibility of further boosting UV light collection in future large detectors by performing such a treatment on the PTFE surfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multiport high-pressure synchrotron x-ray microscopy cell (CRADA Final Report)

The LBNL team developed a multiport cell allowing for fluid flow, with electrical contacts for sample bias, and with reference electrodes. The cell is currently installed and operating in beam-line 11.0.2 of the ALS, the Berkeley Synchrotron. The cell is closed by a membrane consisting of several stacked layers of graphene (1 to 3). The graphene membrane is supported on a 100 nm thick Si3N4 membrane covered with a 20 nm thin gold film for improved adhesion of the graphene and to ensure electrical conductivity. The Si3N4 film is perforated with a periodic array of holes 1 to 2 micrometers diameter. The cell can withhold an internal pressure (gas or liquid) of up to 10 atmospheres for in situ/operando studies using X-ray Photoelectron emission (XPS), and X-ray Absorption Spectroscopy (XAS). It is also ideal for tip-enhanced nano-Infrared Spectroscopy studies of molecules at the interface between the graphene and the liquid or gas filling the cell. Materials studied in the LBNL laboratory are in the form of nanoparticles, or thin films (few nm) deposited on the side of the graphene membrane facing the solution or gas inside the cell.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multilayer Electrodes with Metalized Polymer Current Collector for High-Energy Lithium-Ion Batteries with Extreme-Fast-Charging Capability

The pursuit of batteries capable of extreme fast charging (XFC), that also satisfy high energy and safety criteria, poses a significant challenge to current lithium-ion battery technologies. Additionally, the increasing demand for aluminum (Al) and copper (Cu) in electrification, and vehicle light weighting is driving these metals towards near-critical status in the medium term. This study introduced metalized polymer films by depositing an Al or Cu thin layer onto two sides of a polyethylene terephthalate (PET) film – named mPET/Al and mPET/Cu, as lightweight, cost-effective alternatives to traditional metal current collectors in LIBs. We have utilized current collectors that significantly reduce weight (by 73%), thickness (by 33%), and cost (by 85%) compared to traditional metal foil counterparts. We conducted an extensive evaluation of their mechanical and electrical properties, including in-plane and through-plane resistivities, affirming their suitability for the roll-to-roll battery manufacturing process. Additionally, a novel XFC testing protocol was employed to thoroughly assess the cells' (both half and full-cell) performance across various C-rates and under long-term tests. These advancements have the potential to enhance energy density to 280 Wh/kg at the electrode level under 10-minute charging at 6C. Through testing, including a novel XFC protocol across various C-rates and long-term cycling (up to 1000 cycles) in different cell configurations, we have demonstrated the superior performance of these metalized polymer films. Notably, mPET/Cu and mPET/Al foils exhibited comparable capacities to conventional cells under XFC, with the mPET cells showing a 27% improvement in energy density at 6C and maintaining significant energy density after 1000 cycles. This study underscored the potential of mPET foils to revolutionize the roll-to-roll battery manufacturing process and significantly advance the performance metrics of LIBs in EV applications. Moreover, our results suggest that there is potential to enhance the performance of mPET foils, especially mPET/Al, by optimizing the manufacturing process to achieve higher conductivity.

99 GENERAL AND MISCELLANEOUS↗