Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “test effectiveness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Bond Testing for Effects of Silicone Contamination

In 2003 ATK Thiokol discovered that the smocks and coveralls worn by its operations personnel for safety and contamination control were themselves contaminated with a silicone defoamer and a silicone oil. As a growing list of items have been identified as having this form of contamination, it was desirable to devise a test method to determine if the contamination level detected could cause subsequent processing concerns. The smocks and coveralls could potentially contact bonding surfaces during processing so the test method focused on dry transfer of the silicone from the clothing to the bonding surface.

Plaia, James↗

Suitability of Type-II Fiber Bragg Gratings in Silica Optical Fiber for Temperature Sensing in TREAT

Optical fibers provide a variety of options for instrumentation in reactor environments. Optical fibers can be used to measure multiple physical phenomena including, temperature, strain, pressure, and fluid level. In addition to the various sensing applications, optical fibers are immune to electromagnetic interference, have a small footprint (~100 μm), and a fast response. The Department of Energy and Idaho National Laboratory have considered optical fibers for use as in-pile instrumentation in the Transient Reactor Test Facility (TREAT). TREAT was designed to test reactor fuels under accident conditions by replicating accident conditions for a variety of reactor transients, such as those associated with a loss of coolant accident (LOCA). This work investigates silica fiber optic temperature sensors with inscribed type-II fiber Bragg gratings (FBGs) under conditions similar to those that would be experienced in a TREAT transient. Separate effects testing was used to test the sensors under high-temperature step transients and under irradiation up to a total fluence similar to that of TREAT. Specifically, this work investigates distributed temperature measurements, using the Optical Frequency Domain Reflectometry (OFDR) sensing technique, using a Luna Innovations Optical Backscatter Reflectometer (OBR) 4600, with silica optical fibers inscribed with type-II fiber Bragg gratings (FBGs). In conclusion, separate effects testing of type-II FBGs in silica optical fiber, to high temperature and to neutron fluences that are an order of magnitude larger than fluences that are anticipated for TREAT tests, demonstrate that type-II FBGs in silica optical fiber hold great promise for high-temperature reactor instrumentation in TREAT.

McCary, Kelly↗

Large-Scale Testing of Effects of Anti-Foam Agent on Gas Holdup in Process Vessels in the Hanford Waste Treatment Plant - 8280

The Hanford Waste Treatment Plant (WTP) will vitrify the radioactive wastes stored in underground tanks. These wastes generate and retain hydrogen and other flammable gases that create safety concerns for the vitrification process tanks in the WTP. An anti-foam agent (AFA) will be added to the WTP process streams. Prior testing in a bubble column and a small-scale impeller-mixed vessel indicated that gas holdup in a high-level waste chemical simulant with AFA was up to 10 times that in clay simulant without AFA. This raised a concern that major modifications to the WTP design or qualification of an alternative AFA might be required to satisfy plant safety criteria. However, because the mixing and gas generation mechanisms in the small-scale tests differed from those expected in WTP process vessels, additional tests were performed in a large-scale prototypic mixing system with in situ gas generation. This paper presents the results of this test program. The tests were conducted at Pacific Northwest National Laboratory in a ¼-scale model of the lag storage process vessel using pulse jet mixers and air spargers. Holdup and release of gas bubbles generated by hydrogen peroxide decomposition were evaluated in waste simulants containing an AFA over a range of Bingham yield stresses and gas gen geration rates. Results from the ¼-scale test stand showed that, contrary to the small-scale impeller-mixed tests, gas holdup in clay without AFA is comparable to that in the chemical waste simulant with AFA. The test stand, simulants, scaling and data-analysis methods, and results are described in relation to previous tests and anticipated WTP operating conditions.

08 HYDROGEN↗

Large-Scale Testing of Effects of Anti-Foam Agent on Gas Holdup in Process Vessels in the Hanford Waste Treatment Plant

The Hanford Waste Treatment and Immobilization Plant (WTP) will vitrify the radioactive wastes stored in underground tanks. These wastes generate and retain hydrogen and other flammable gases that create safety concerns for the vitrification process tanks in the WTP. An anti-foam agent (AFA) will be added to the WTP process streams. Previous testing in a bubble column and a small-scale impeller-mixed vessel indicated that gas holdup in a high-level waste chemical simulant with AFA was as much as 10 times higher than in clay simulant without AFA. This raised a concern that major modifications to the WTP design or qualification of an alternative AFA might be required to satisfy plant safety criteria. However, because the mixing and gas generation mechanisms in the small-scale tests differed from those expected in WTP process vessels, additional tests were performed in a large-scale prototypic mixing system with in situ gas generation. This paper presents the results of this test program. The tests were conducted at Pacific Northwest National Laboratory in a 1/4-scale model of the lag storage process vessel using pulse jet mixers and air spargers. Holdup and release of gas bubbles generated by hydrogen peroxide decomposition were evaluated in waste simulants containing an AFA over a range of Bingham yield stresses and gas generation rates. Results from the 1/4-scale test stand showed that, contrary to the small-scale impeller-mixed tests, holdup in the chemical waste simulant with AFA was not so greatly increased compared to gas holdup in clay without AFA. The test stand, simulants, scaling and data-analysis methods, and results are described in relation to previous tests and anticipated WTP operating conditions. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Test-Derived Effective Emittance for Cassini MLI Blankets and Heat Loss Characteristics in the Vicinity of Seams

Multilayer insulation (MLI) blankets on the Cassini spacecraft will experience temperatures in the wide range of -200 to 360°C. Besides reducing heat loss, the MLI blankets will also serve, with standoffs, the purpose of micrometeoroid protection. Four major blanket layup configurations ??will be utilized on Cassini. Since definitive thermal properties for these layups were not available, thermal vacuum tests were conducted for their determination.

multilayer↗

Dust charging effects on test charge potential in a multi-ion dusty plasma

The Debye-Hueckel and oscillatory wake potentials caused by a test charge are studied in a multi-ion dusty plasma, whose constituents are the Boltzmann distributed electrons and light positive ions, the heavy mobile negative ions, and static but charge fluctuating dust particles. For this purpose, fluid equations are employed to obtain the dielectric constant of the dust-negative-ion acoustic wave involving the negative ions and dust charge fluctuation effects. Theoretical and numerical investigations have revealed the modification in the Debye-Hueckel and wake potentials due to the effects of dust relaxation rate, dust absorption frequency, dust grain radius, and negative ion temperature. The present results should be important to form new materials in the presence of negative ions in laboratory as well as dust coagulation/agglomeration in space dusty plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Lab Tests Demonstrate Effectiveness of Advanced Power Strips [Fact Sheet]

NREL engineers evaluate the functionalities of advanced power strips and help consumers choose the right one for their plug loads. Many consumer electronics devices waste energy even after they are turned off via “vampire” loads, meaning they continue to draw current as long as they remain plugged into receptacles. In a typical home with 40 plug loads, vampire loads can account for nearly 10% of household electricity use. Advanced power strips (APS) are a convenient and inexpensive way to curb this type of energy waste, and are the focus of laboratory tests conducted by the Residential Buildings group at the National Renewable Energy Laboratory (NREL). By replacing ordinary power strips with APS, appliances that are not in use can be automatically shut off. APS are designed primarily for the home office and entertainment center, where the concentration of consumer electronics is typically high.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

A simple model for testing the effects of gravity-wave-produced vertical oscillations of scattering irregularities on spaced-antenna, horizontal drift measurements

It has been suggested that the velocities produced by the spaced antenna partial-reflection drift experiment may constitute a measure of the vertical oscillations due to short-period gravity waves rather than the mean horizontal flow. The contention is that the interference between say two scatterers, one of which is traveling upward, and the other down, will create a pattern which sweeps across the ground in the direction (or anti-parallel) of the wave propagation. Since the expected result, viz., spurious drift directions, is seldom, if ever, seen in spaced antenna drift velocities, this speculation is tested in an atmospheric model.

Meek, C. E.↗

Modeling and design of a separate effects irradiation test targeting fission gas release from Cr-doped UO 2

Fission gas release (FGR) from nuclear fuel during operation can diminish heat transfer properties across the pellet-cladding gap and increase the fuel rod internal pressure, thereby posing a concern to fuel reliability and safety during an accident. Enlarging the fuel grain size, which has been shown to improve fission gas retention, can be achieved by doping the fuel feedstock prior to sintering. In this work, the BISON fuel performance code was used to predict FGR from undoped and chromia-doped UO 2 (referred to as Cr-doped UO 2 ) fuel specimens with different grain sizes and across various temperatures. The BISON models identified the irradiation conditions for which FGR is most significant, and a separate effects irradiation experiment in the High Flux Isotope Reactor (HFIR) was then developed targeting those conditions. Further, the experiment leveraged the MiniFuel irradiation capability at Oak Ridge National Laboratory and consisted of 12 fuel specimens of varying grain size and Cr content. A coupling scheme between BISON FGR results and the ANSYS finite element thermal model used for experiment design was formulated to predict cumulative FGR from each fuel specimen based on expected irradiation temperature histories. The fuel samples were fabricated and characterized as a part of this work, and the fuel compositions modeled in BISON were representative of the specimens used in the experiment. This combined modeling and experimental effort aims to study the effect of fuel grain size and Cr content on FGR and to provide simulated BISON FGR results that can be used for future model validation activities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Constrained tree growth and gas-exchange of seawater-exposed forests in the Pacific Northwest, USA

1. Rising sea levels under climate change may have significant impacts on coastal vegetation dynamics, yet the response of coastal forest growth, gas-exchange, and survival to seawater intrusion remains poorly documented. 2. We conducted a dendroecology study across six sites in western Washington, USA, to examine how tree growth, gas exchange (indexed by basal area increment, BAI, and wood d13C, respectively), and survival varies with seawater exposure through two approaches. First, tree core samples were collected at a site where seawater exposure started only four years prior to sampling, which allowed a cause-and-effect test of the impacts of seawater exposure on trees, and second, samples were collected at five additional sites where we compared downstream to upstream trees under current sea-level conditions. 3. At the seawater intrusion site, BAI and carbon isotope discrimination (?) decreased significantly (p < 0.01) in the year of intrusion (2014) and stayed unchanged thereafter. Four years later (2018), the percentage of recently standing dead trees in the forest was 73.0% basal area. Across the regional assessment, percentage of standing dead trees was significantly greater in downstream than upstream forests at five of the six sites (averaged 37.7±11.0% and 4.3±2.1% basal area for downstream and upstream, respectively). Growth was significantly lower (p < 0.01) at the downstream than upstream for five sites, and ? was lower for all needle-leaf trees (three sites) on the downstream compared to the upstream, but no difference was observed between downstream and upstream for broad-leaf trees (three sites). 4. Synthesis Combined, both the cause-and-effect manipulative study and the regional assessment demonstrate that seawater exposure drives reductions in growth, decreased ? of needle-leaf trees, increased mortality, and greater climate sensitivity, regardless of whether the seawater exposure is recent or long-term.

Costal forests, tree growth, tree-ring, tree morta↗

Fast Ion Effects During Test Blanket Module Simulation Experiments in DIII-D

Fast beam-ion losses were studied in DIII-D in the presence of a scaled mockup of two Test Blanket Modules (TBM) for ITER. Heating of the protective tiles on the front of the TBM surface was found when neutral beams were injected and the TBM fields were engaged. The fast-ion core confinement was not significantly affected. Different orbit-following codes predict the formation of a hot spot on the TBM surface arising from beam-ions deposited near the edge of the plasma. The codes are in good agreement with each other on the total power deposited at the hot spot predicting an increase in power with decreasing separation between the plasma edge and the TBM surface. A thermal analysis of the heat flow through the tiles shows that the simulated power can account for the measured tile temperature rise. The thermal analysis, however, is very sensitive to the details of the localization of the hot spot which is predicted to be different among the various codes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Ductility of 49Fe-49Co-2V Soft Magnetic Alloy Bar: Surface Effects and Test Methods

The tensile ductility of 49Fe-49Co-2V (Hiperco® 50A) bar was investigated in both as-received and heat-treated conditions. The as-received/machined specimens exhibit very low ductility compared to samples where heat treatment was the final step prior to testing. Microstructural characterization showed that internal residual strain from bar processing and, most importantly, surface machining damage, cause lower elongation in the as-received material. Because fracture of this intermetallic alloy initiates at the surface, it is particularly susceptible to surface machining damage, i.e., the near-surface region has already exhausted most of its ability to accumulate tensile strain. During heat treatment, the internal residual strain and near-surface machining damage are eliminated and ductility is improved, despite a higher degree of crystallographic ordering in the heat-treated condition (which typically lowers ductility). Furthermore, if machining is again performed after heat treatment, the material again exhibits brittle behavior, even with only light touch-up machining passes. Here, in this work, methods of tensile strain measurement were investigated, namely conventional knife-edge extensometry and noncontact digital image correlation (DIC) on heat-treated material. For clip-on knife-edge extensometry, the range of failure strain was 2.5-5.5% for heat-treated Hiperco. For noncontact methods, ductility up to 7% was observed. The results highlight the tendency for the alloy to fail at surface imperfections, even those produced by application of the extensometer itself. Noncontact laser extensometry is recommended for determining the intrinsic ductility of the alloy. A method of laser surface modification was developed which increased ductility by ~ 100% compared to unmodified samples. The high cooling rates achieved during laser surface processing can bypass the ordering reaction and produce a ductile disordered structure at the surface that exhibits ductile fracture characteristics.

EBSD↗

Fast-ion effects during test blanket module simulation experiments in DIII-D

Fast beam-ion losses were studied in DIII-D in the presence of a scaled mock-up of two test blanket modules (TBM) for ITER. Heating of the protective tiles on the front of the TBM surface was found when neutral beams were injected and the TBM fields were engaged. The fast-ion core confinement was not significantly affected. Different orbit-following codes predict the formation of a hot spot on the TBM surface arising from beam ions deposited near the edge of the plasma. The codes are in good agreement with each other on the total power deposited at the hot spot, predicting an increase in power with decreasing separation between the plasma edge and the TBM surface. A thermal analysis of the heat flow through the tiles shows that the simulated power can account for the measured tile temperature rise. The thermal analysis, however, is very sensitive to the details of the localization of the hot spot, which is predicted to be different among the various codes.

Kramer, G↗