Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “task”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Impact of Automation Support on the Conflict Resolution Task in a Human-in-the-Loop Air Traffic Control Simulation

To determine the capabilities and limitations of human operators and automation in separation assurance roles, the second of three Human-in-the-Loop (HITL) part-task studies investigated air traffic controllers ability to detect and resolve conflicts under varying task sets, traffic densities, and run lengths. Operations remained within a single sector, staffed by a single controller, and explored, among other things, the controllers responsibility for conflict resolution with or without their involvement in the conflict detection task. Furthermore, these conditions were examined across two different traffic densities; 1x (current-day traffic) and a 20 increase above current-day traffic levels (1.2x). Analyses herein offer an examination of the conflict resolution strategies employed by controllers. In particular, data in the form of elapsed time between conflict detection and conflict resolution are used to assess if, and how, the controllers involvement in the conflict detection task affected the way in which they resolved traffic conflicts.

human-in-the-loop simulation↗
NASA NTRS2018

Time-Varying Manual Control Identification in a Stall Recovery Task Under Different Simulator Motion Conditions

This paper adds data to help the development of simulator motion cueing guidelines for stall recovery training by identifying time-varying manual control behavior in a stall recovery task under different simulator motion conditions. A study was conducted with seventeen general aviation pilots in the NASA Ames Vertical Motion Simulator. Pilots had to follow a flight director through four stages of a high-altitude stall task. A time-varying identification method was used to quantify how pilot manual control parameters change throughout different stages of the task in both roll and pitch. Four motion configurations were used: no motion, generic hexapod motion, enhanced hexapod motion and full motion. Pilot performance was highest for the enhanced hexapod and full motion configurations in both roll and pitch, and the lowest without motion. In the roll axis, the pilot position gain did not significantly change throughout the stall task, but was the lowest for the condition with no motion. The pilot roll velocity gain was significantly different between motion conditions, the largest difference being found close to the stall point. The enhanced hexapod motion condition had the highest pilot roll velocity gain. In the pitch axis, the pilot position gain was significantly different between time segments but not between motion conditions. The pilot pitch velocity gain was highest for the full motion condition and increased close to the stall point, but did not change significantly for the other motion conditions. Overall, pilot control behavior under enhanced hexapod motion was most similar to that under full aircraft motion. This indicates that motion cueing for stall recovery training on hexapod simulators might be improved by using the principles behind the enhanced hexapod motion configuration.

manual control↗
NASA NTRS2018

Time-Varying Manual Control Identification in a Stall Recovery Task under Different Simulator Motion Conditions

This paper adds data to help develop simulator motion guidelines for stall recovery training by identifying time-varying manual control behavior in a stall recovery task under different simulator motion conditions. A study was conducted in the NASA Ames Vertical Motion Simulator, where seventeen general aviation pilots performed a stall recovery task. Pilots had to follow a flight director through four stages of the stall recovery task. A time-varying identification method was used to quantify how pilots weigh position and velocity information throughout different stages of the task, in both roll and pitch. Four motion configurations were used: no motion, generic hexapod motion, enhanced hexapod motion and full motion. Pilot performance was highest for the enhanced hexapod and full motion conditions in both roll and pitch, and the lowest for the condition with no motion. The time-varying identification method revealed that, in the roll axis, pilot position gain did not significantly change between time segments, but was the lowest for the condition with no motion. The pilot velocity gain was significantly different between motion conditions, the largest difference being found at the beginning of the stall. The enhanced hexapod motion condition had the highest pilot velocity gain. In the pitch axis, the pilot position gain was significantly different between time segments but not between motion conditions. The pitch pilot velocity gain was highest for the full motion condition and increased at the beginning of the stall, but did not change significantly for the other motion conditions. Overall, pilot control behavior under enhanced hexapod motion was more similar to that under full aircraft motion compared to standard hexapod motion. This indicates that motion cueing on hexapod simulators might be improved for stall recovery training by using the enhanced hexapod motion developed in previous experiments.

stall recovery↗
NASA NTRSDate not supplied

Towards a Characterization of Scheduling Task Complexity

Future long-duration missions will require astronauts to act more autonomously, manage their schedules, and replan timelines as anomalies and discoveries occur. Astronauts are not professional planners, however, and the complexity of schedules that novice planners can complete successfully is not fully understood. To identify the primary factors which contribute to scheduling task complexity, we conducted a human-in-the-loop study and developed planning algorithms to investigate how the type and amount of constraints affect the difficulty of scheduling and rescheduling. We created rankings of difficulty using a combination of human performance metrics from experimental planning tasks and metrics describing the final plans that participants scheduled. Using the results of our scheduling and rescheduling algorithm algorithms, we created a similar ranking with which to compare. We created rankings which compared well between the experimental and algorithm results for the scheduling task, but the rescheduling task proved more difficult to estimate.

scheduling↗
NASA NTRSDate not supplied

Towards a Characterization of Scheduling Task Complexity

Future long-duration missions will require astronauts to act more autonomously, manage their schedules, and replan timelines as anomalies and discoveries occur. Astronauts are not professional planners, however, and the complexity of schedules that novice planners can complete successfully is not fully understood. To identify the primary factors which contribute to scheduling task complexity, we conducted a human-in-the-loop study and developed planning algorithms to investigate how the type and amount of constraints affect the difficulty of scheduling and rescheduling. We created rankings of difficulty using a combination of human performance metrics from experimental planning tasks and metrics describing the final plans that participants scheduled. Using the results of our scheduling and rescheduling algorithm algorithms, we created a similar ranking with which to compare. We created rankings which compared well between the experimental and algorithm results for the scheduling task, but the rescheduling task proved more difficult to estimate.

scheduling↗
NASA NTRSDate not supplied

Operator Workload and Task Allocation in m:N Operational Architectures of Uncrewed Aerial Systems

Uncrewed aerial systems (UAS) show promise in urban air transport, package delivery, and emergency services. UAS efficiency can be significantly improved by having fewer operators (m) manage a greater number of vehicles (N), or the m:N architecture of operation. The current study investigates how workload affects operators’ task-allocation decision-making and potential effects of two crucial human factors: trust and self-confidence. In the context of a simulated UAS package-delivery task, 10 participants with expertise in UAS operation were recruited. Each participant reported their preferred task-allocation strategy for a set of five subtasks while watching two sets of videos with different workload levels. Perceived workload, trust, and self-confidence were also measured after each video session. Overall, participants indicated a preference for automation for most of the subtasks under the delivery mission. Trust, rather than workload and self-confidence, played a significant role in experts’ decisions of task-allocation and assignment methods. Higher trust led to higher preference for automation.

workload↗
DOE OSTI2025

Time Distribution Analysis for Task Primitives to Support Dynamic Human Reliability Analysis

To support data collection for dynamic human reliability analysis (HRA), this study investigates time distributions for task primitives defined in the Goals, Operators, Methods, and Selection rules (GOMS)–Human Reliability Analysis (HRA) method and Human Reliability data EXtraction (HuREX). GOMS-HRA was developed to provide cognition-based time and human error probability (HEP) information for dynamic HRA calculations within the Human Unimodel for Nuclear Technology to Enhance Reliability (HUNTER) framework, while HuREX is a comprehensive HRA data collection method developed by the Korea Atomic Energy Research Institute (KAERI). In this paper, we examine time distributions by using experimental data collected from the Simplified Human Error Experimental Program (SHEEP) study, which proposes an HRA data collection framework to complement full-scope simulator research and gather input data for dynamic HRA by using simplified simulators such as the Rancor Microworld simulator. This paper investigates whether the time required for GOMS-HRA and HuREX task primitives fits 13 statistical distributions. Additionally, we compare and discuss the time distributions obtained from both student operators and professional operators. The result was that this study identified several time distributions for five GOMS-HRA and four HuREX task primitives. In the future, the results of this study are expected to provide objective reference data on the elapsed time for task primitives and aid in realistically simulating scenarios within dynamic HRA.

Dynamic Human Reliability Analysis↗
NASA NTRS1995

Game-like tasks for comparative research: leveling the playing field

Game-like computer tasks offer many benefits for psychological research. In this paper, the usefulness of such tasks to bridge population differences (e.g., age, intelligence, species) is discussed and illustrated. A task called ALVIN was used to assess humans' and monkeys' working memory for sequences of colors with or without tones. Humans repeated longer lists than did the monkeys, and only humans benefited when the visual stimuli were accompanied by auditory cues. However, the monkeys did recall sequences at levels comparable to those reported elsewhere for children. Comparison of similarities and differences between the species is possible because the two groups were tested with exactly the same game-like paradigm.

NASA Discipline Number 06-10↗
NASA NTRS2014

A Task Analytic Process to Define Future Concepts in Aviation

A necessary step when developing next generation systems is to understand the tasks that operators will perform. One NextGen concept under evaluation termed Single Pilot Operations (SPO) is designed to improve the efficiency of airline operations. One SPO concept includes a Pilot on Board (PoB), a Ground Station Operator (GSO), and automation. A number of procedural changes are likely to result when such changes in roles and responsibilities are undertaken. Automation is expected to relieve the PoB and GSO of some tasks (e.g. radio frequency changes, loading expected arrival information). A major difference in the SPO environment is the shift to communication-cued crosschecks (verbal / automated) rather than movement-cued crosschecks that occur in a shared cockpit. The current article highlights a task analytic process of the roles and responsibilities between a PoB, an approach-phase GSO, and automation.

single pilot operations↗
NASA NTRS2017

Autonomous Task Management and Decision Support Tools

For some time aircraft manufacturers and researchers have been pursuing mechanisms for reducing crew workload and providing better decision support to the pilots, especially during non-normal situations. Some previous attempts to develop task managers or pilot decision support tools have not resulted in robust and fully functional systems. However, the increasing sophistication of sensors and automated reasoners, and the exponential surge in the amount of digital data that is now available create a ripe environment for the development of a robust, dynamic, task manager and decision support tool that is context sensitive and integrates information from a wide array of on-board and off aircraft sourcesa tool that monitors systems and the overall flight situation, anticipates information needs, prioritizes tasks appropriately, keeps pilots well informed, and is nimble and able to adapt to changing circumstances. This presentation will discuss the many significant challenges and issues associated with the development and functionality of such a system for use on the aircraft flight deck.

decision support↗
NASA NTRSDate not supplied

A Partitioned - Task Parallel Implementation of the NASA Multiscale Analysis Tool for High Performance Computing

The NASA Multiscale Analysis Tool (NASMAT) is a platform for multiscale modeling of composites which can perform analysis of materials with any arbitrary number of length scales. The platform supports modularity, scalability, and interoperability using recursive procedures and data structures. A Macro solver driven parallelization scheme often limits the capability of NASMAT to scale as it has access to limited memory and number of cores (often one core/thread) and often forces to implement macro solver specific changes to the platform. In this work, a partitioned task-parallel approach is adopted, where the parallelization strategy adopted for NASMAT is independent of the macro solver and the computational resources are managed independently. The programming architecture takes into account the hierarchy of multiple scales (task-dependence) and the heterogeneous nature (dynamic load balancing) of computation through implementation of a hierarchy-informed task parallel model. The partitioned nature of the framework further extends the “plug and play” capability of NASMAT. preCICE, an open-source library for coupling multiphysics solver in a partitioned manner, is adopted to integrate NASMAT with an external macro solver by implementing a NASMAT adapter for preCICE. Speedup and scalability of the framework is studied for micromechanical models of varying size.

task-parallel↗
NASA NTRSDate not supplied

Analysis and Evaluation of NASA's MK40B Six-Component TASK Balance

The paper discusses the physical characteristics NASA's MK40B TASK balance. It is NASA's newest TASK balance that was optimized for the testing of wind tunnel models in the NASA Ames 11-ft Transonic Wind Tunnel. The calibration data of the MK40B balance was obtained in Calspan's Automatic Balance Calibration System. A machine load schedule design was used for the calibration that was developed at the NASA Ames Balance Calibration Laboratory. The calibration data was analyzed using both the Non-Iterative Method and the Iterative Method. Then, the chosen regression models of the calibration data were assessed and compared using the percent contribution, the variance inflation factor, and the calibration load residuals. Interactions of single-component loads were also quantified. In addition, the bi-directional characteristics of the six gage outputs of the balance were assessed by applying a semi-empirical test that was developed at the Ames Balance Calibration Laboratory. It was concluded that four of the six gages of the balance have bi-directional characteristics. Finally, the accuracy of the load prediction equations of the balance was tested by applying the equations to independent check load data that was obtained at the NASA Ames Balance Calibration Laboratory. The standard deviation of the check load residuals met expectations. The check load data also confirmed that the interactions of the forward and aft normal forces on the axial force gage output are very small. - This paper is to be presented in the invited special session titled: "65 Years of TASK Wind Tunnel Balances - Past, Present, and Future".

wind tunnel balance↗
NASA NTRSDate not supplied

A Partitioned -Task Parallel Implementation of the NASA Multiscale Analysis Tool for High Performance Computing

The NASA Multiscale Analysis Tool (NASMAT) is a “plug and play” software package that allows users to conduct massively multiscale modeling of hierarchical and nonlinear materials. This work extends the scalability and improves the High Performance Computing friendliness of NASMAT by adopting a Partitioned Task-Parallel approach. Interoperability of NASMAT with external software is enhanced through preCICE, a open source library for multiphysics coupling in a partitioned manner. Enhancement through preCICE allows for easy integration of NASMAT to other macro solvers and dissociates the parallelization strategy adopted within NASMAT from the macro solver. The task-parallel framework based on Master-Worker approach is implemented as the parallelization scheme. The scheme accounts for hierarchy of multiple scales (task-dependence) and heterogeneous nature (dynamic load balancing) of computations. The applicability and scalability of the framework will be evaluated by analyzing large scale engineering problems through massively multiscale methods.

NASMAT↗
NASA NTRS2023

Framework for Extensible, Asynchronous Task Scheduling (FEATS) in Fortran

Most parallel scientific programs contain compiler directives (pragmas) such as those from OpenMP, explicit calls to runtime library procedures such as those implementing the Message Passing Interface (MPI), or compiler-specific language extensions such as those provided by CUDA. By contrast, the recent Fortran standards empower developers to express parallel algorithms without directly referencing lower-level parallel programming models. Fortran’s parallel features place the language within the Partitioned Global Address Space (PGAS) class of programming models. When writing programs that exploit data-parallelism, application developers often find it straightforward to develop custom parallel algorithms. Problems involving complex, heterogeneous, staged calculations, however, pose much greater challenges. Such applications require careful coordination of tasks in a manner that respects dependencies prescribed by a directed acyclic graph. When rolling one’s own solution proves difficult, extending a customizable framework becomes attractive. The paper presents the design, implementation, and use of the Framework for Extensible Asynchronous Task Scheduling (FEATS), which we believe to be the first task-scheduling tool written in modern Fortran. We describe the benefits and compromises associated with choosing Fortran as the implementation language, and we propose ways in which future Fortran standards can best support the use case in this paper.

Modern Fortran↗
DOE OSTI2025

Synchro-Waveform-Based Event Identification Using Multi-Task Time-Frequency Transform Networks

Influenced by the transient dynamics and reduced inertia characteristics of high-penetration renewable energy systems, power system events frequently exhibit distinct characteristics such as high-frequency components including wide-band oscillations and hyper-harmonics. This makes standard systems face challenges including significant latency and reduced accuracy due to limited data resolution. However, current methods face significant limitations, including insufficient pattern capture ability, low noise immunity, limited feature learning, and restricted localization capabilities, thereby hindering real-time performance. To tackle this issue, this paper proposed a novel synchro-waveform-based event identification approach via a Multi-task Time-frequency Transform Network (MTTNet). Initially, a Time-frequency Transform Block (TTB) is developed to extract both local and global information. The TTB leverages both Fourier and S-transforms to derive comprehensive time-frequency information from synchro-waveforms. Subsequently, a multi-task learning strategy is employed to identify the type and distinguish localization of events. Integrating the TTB and multi-task learning, the MTTNet is designed for synchro-waveform-based event identification, incorporating an adaptive weighting strategy and simplified computation for the S-transform. Two different datasets, comprising simulated and actual synchro-waveforms, are collected from the IEEE 123 bus system and a real-world high-penetration renewable energy system using a universal grid analyzer. Extensive experiments on various conditions are carried out. In conclusion, results demonstrated that the MTTNet consistently surpasses both basic and advanced baselines, with maximum improvements of 13.24% and 9.86%, respectively, while reducing the calculation burden by 15-19 times to achieve real-time event identification.

Event identification↗
DOE OSTI2024

Numerical eigen-spectrum slicing, accurate orthogonal eigen-basis, and mixed-precision eigenvalue refinement using OpenMP data-dependent tasks and accelerator offload

Performing a variety of numerical computations efficiently and, at the same time, in a portable fashion requires both an overarching design followed by a number of implementation strategies. All of these are exemplified below as we present transitioning the PLASMA numerical library from relying on dependence-driven large tasks to achieving utilization of fine grain tasking and offload to hardware accelerators while keeping its core dependence sets: OpenMP source code pragmas and runtime for most system-level functionality and basic low-level numerical kernels provided directly by hardware vendors or open source projects with vendor contributions. We also present new algorithmic methods and their efficient parallel implementations including fine grained tasking for eigen-spectrum slicing and offload for mixed-precision eigenvalue refinement. We provide performance, scaling, and numerical results showing sizable gains over the available solutions from either the open source and vendor-provided packages.

Luszczek, Piotr↗
DOE OSTI2024

DECOVALEX-2023: Task C Final Report

The Full-scale Emplacement (FE) heater experiment at the Mont Terri Underground Rock Laboratory (URL) was designed and conducted by Nagra to replicate an emplacement tunnel of Nagra’s reference repository design at 1:1 scale. Alongside testing the technical feasibility of constructing disposal tunnels, emplacing waste containers in the tunnels and then backfilling them, the main goals of the FE experiment are (1) to obtain a better understanding of the coupled effects of induced thermo-hydro-mechanical (THM) processes that may occur and (2) to validate existing coupled THM models (Müller et al., 2017). A key aspect of ensuring safety for repositories located in low-permeability rock involves minimizing any damage to the rock itself, thereby preserving its integrity and promoting a stable environment Amongst a number of processes that could damage the rock is the increase in pore pressure due to thermal loading caused by heat emitted from the waste. To reduce the potential damage of the rock, it is important to analyse the evolution of heat over time due to the heat load of the containers and assess possible consequences by coupled THM models. The aim of Task C of DECOVALEX-2023 was to build 3D numerical models of the FE experiment, focussing in particular on the heating induced pore pressure change in the Opalinus Clay. Data from a large number of sensors were available from the FE experiment for model comparison. These sensors measured temperature and relative humidity in the bentonite around the heaters, and temperature, pressure and displacement/strain in the surrounding Opalinus clay. Data were available from the start of excavation (April 2012) up to August 2020 for most sensors (more than 5 years from the start of heating in December 2014). To fulfil the overall aim of the task, the work was broken down into a number of steps, starting with simpler models to build confidence in each team’s approach and then moving to more complex models that better represent the FE experiment. Step 0 consisted of 2D benchmark models, gradually increasing the number of processes that are represented from thermal (T) only models in Step 0a, to coupled thermal hydraulic (TH) models in Step 0b with a representation of changing porosity, to coupled thermo-hydro-mechanical (THM) models in Step 0c, where porosity changes are calculated by the mechanical model. A detailed specification of processes, parameters, initial and boundary conditions was provided for this step, with the ambition that all teams would work towards close agreement in their model results, thus building confidence in the model implementations. vi It was not straightforward to achieve agreement between the teams, so additional steps (Step 0b2, 0b3, 0c2, 0c3) were added along with derivation of some analytical solutions against which the models could be compared. The reasons for the differences between teams were investigated and found to be caused primarily by different conceptual model assumptions (including temperature dependence of the thermal expansion of water), different model formulations (including porosity evolution) and differences in modelled domain sizes, boundary conditions and grid discretisation. This demonstrates that comparisons between multiple modelling teams and/or comparison with analytical results and experimental data are highly beneficial in providing an indication of uncertainty in model predictions. At the conclusion of Step 0, almost all teams had achieved a close agreement in model results and those that had not achieved an agreement knew the reason for this. Step 1 moved from 2D models to 3D models of the FE experiment without adding technical features like shotcrete or EDZ, and only considering the heating phase. Initially the 3D model was tightly specified to continue to build confidence in the model implementations (Step 1a). The results of Step 1a were compared to the data from the FE-experiment without the teams seeing the data. The teams were then provided with a sub-set of the data from the FE-experiment and invited to consider how best to use the large dataset for model comparison (Step 1b). Teams were then asked to use the data provided to calibrate their models, only changing material property values rather than adding features or processes to their models (Step 1c). In Step 1, teams were asked to only model the heating phase of the experiment, so pressure in the Opalinus Clay was reported as change in pressure since the initial conditions were specified rather than modelled. The change from 2D to 3D models was accompanied by an increase in the dispersion of results between the teams. Some of this was resolved during the task, but some remained and is potentially due to model discretisation. Calibration of parameters was useful in improving the fit of the models to the data but the remaining differences indicated that the models were missing features or processes. In Step 2, the teams were asked to update their models with additional features and processes as well as calibrating parameters to try and improve the fit of the models to the data. Teams were encouraged to represent ventilation of the open FE tunnel prior to backfilling with heaters and bentonite and in Step 2, the absolute pressure in the Opalinus Clay was compared between the teams. Teams took different approaches, but there was consideration of adding shotcrete and an EDZ into the model, representing stress change during excavation and different approaches to modelling ventilation of the FE tunnel. Overall, the documented results showed a very good agreement for temperature. The results for porewater pressure evolution showed a significant improvement for most teams compared to Step 1c with a good agreement to the measurements for several teams whereas some teams overpredicted the pressure increase and others overpredicted the drainage effect especially for the sensors close to the heater. Step 3 was an opportunity for teams to use the models developed in Step 1 and Step 2 to make predictions about the temperature and pressure changes that will be expected at the FE experiment over the next few years in light of the planned changes in thermal output of the heaters.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

MRCI Task 3: Facilitating Data Collection, Sharing, and Analysis Final Technical Summary Report

The Midwest Regional Carbon Initiative (MRCI) Task 3.0 was defined to facilitate development of carbon capture, utilization, and storage (CCUS) in the region by collection and sharing of existing and new technical data from CCUS projects and research. The task also included support for further analysis and assessment of tools by the project team and by researchers working on programs such as National Risk Assessment Partnership (NRAP), machine learning (ML) techniques, and assessment and improvement of CCUS site assessment, operations, and monitoring aspects. Work under Task 3.0 addressed key issues related to CCUS deployment and provided foundational research and datasets to help establish CCUS projects in the MRCI. Report Authors and Principal Technical Contributors: Joel Sminchak, Laura Keister, Mackenzie Scharenberg, Priya Ravi-Ganesh, Autumn Haagsma, Srikanta Mishra, Jared Hawkins, Jared Schuetter, Amy Lang, Jaelen Lewis, Derrick James, Jorge Barrios, Stuart Skopec, and Sanjay Mawalkar (Battelle). Chris Korose, Carl Carmen, Nate Grigsby, Nathan Webb (Illinois State Geological Survey). Principal Investigators: Dr Neeraj Gupta, Dr. Chris Korose.

MRCI,NRAP,data collection,data compilation,legacy ↗