Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sorbent”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Comparison of microwave and conventional heating for CO 2 desorption from zeolite 13X

In this study, we investigate microwave irradiation as an alternative to conventional heating for temperature swing adsorption processes. The performance of microwave and conventional heating during sorbent regeneration was evaluated by measuring CO 2 desorption from zeolite 13X at different temperatures. Experimentally, a fixed bed of zeolite 13X was saturated by a 150 sccm flow of 15 % CO 2 at room temperature followed by sorbent regeneration under nitrogen at 55, 100, or 150 °C by applying either microwave irradiation or conventional heating. Microwaves reduced sorbent regeneration times by at least half compared to regeneration by conventional heating. Under conventional regeneration, desorption curves were resolved into two peaks representing physisorbed CO 2 (mass diffusion limited) at low temperature and bicoordinated CO 2 (thermally limited) with increasing temperature. Under microwave regeneration, only one desorption peak was observed suggesting that CO 2 desorption was limited by mass diffusion through the porous zeolite 13X structure, rather than by temperature. Depending on microwave power, apparent activation energy of the microwave-assisted regeneration was 15.8–18.1 kJ/mol, compared to 41.5 kJ/mol for conventional regeneration. The reduction in apparent activation energy is mainly attributed to selective microwave heating of CO 2 adsorption sites (Na + sites) resulting in greater steady state temperatures of Na + relative to framework atoms, suggesting greater heating efficiency due to microwaves compared to conventional heat transfer. Due to rapid cycling and efficient heat transfer to CO 2 sites on zeolite 13X, microwave regeneration is found to increase adsorption/desorption cycling productivity and potentially reduce the energy penalty of temperature swing capture.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Manipulating Pore Topology and Functionality to Promote Fluorocarbon-Based Adsorption Cooling

With the worldwide demand for refrigeration and cooling expected to triple, it is increasingly important to search for alternative energy resources to drive the refrigeration cycles with reduced electricity consumption. Recently, adsorption cooling has gained increased attention since energy reallocation in such systems is based on gas adsorption/desorption, which can be driven by waste/natural heat sources. Eco-friendly sorption-based cooling relies on the cyclic transfer of refrigerant gas from a high to low energy state by the pseudo-compression effect resulting from adsorption and desorption. The driving force for energy transfer relies on heat rather than electricity. The performance of a sorption chiller is primarily influenced by this cyclic sorption behavior, which is characterized as the working capacity of the porous sorbent. Thus increases in this working capacity directly translate to a more compact and efficient cooling system. How-ever, a lack of highly effective sorbent/refrigerant pairs lowers cooling performance, and therefore has limited applicability. To this end, synthetic metal-organic frameworks (MOFs) and covalent organic polymers (COPs) possess higher porosity and greater tunability leading to more substantial potential benefits for adsorption, compared to traditional sorbent materials. Similarly, hydrofluorocarbon refrigerants have more favorable applicability given ease of operation above atmospheric pressures due to suitable saturated vapor pressures and boiling points. For these reasons, our work focuses on an ongoing strategy to promote sorption cooling via improvements in the sorbent/refrigerant pair. Specifically, we target the interaction of hydrofluorocarbon refrigerants with MOF/COP materials at a molecular level by interpreting the host-guest chemistry and the role of framework pore topology. These molecular level differences translate to cooling performance, which is described herein. These strategies include engineering framework porosity (i.e., pore size, pore volume) by using elongated organic linkers and stereochemistry control during synthesis; manipulating the sorb-ate/sorbent interaction by introducing functional moieties or unsaturated metal centers to enhance working capacities in narrow pressure ranges; varying pore topology/morphology to impact adsorption isotherm behavior; and leveraging defective sites within the frameworks to further enhance adsorption capability. Here this atomic level understanding of sorb-ate-sorbent interactions is conducted using various in situ experimental techniques such as synchrotron-based X-ray diffraction, X-ray absorption spectroscopy, in situ Fourier transform infrared spectroscopy, and direct sorption energies determinization with calorimetry. Moreover, the experimentally studied interactions and the corresponding adsorption mechanism are corroborated by computational studies using density functional theory (DFT) and grand canonical Monte Carlo (GCMC) simulations. Using this approach, we envision the capability to engineer designed frameworks with precise molecular control to target refrigerant molecules and thereby enhance the performance of desired working pairs for sorption-based cooling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Liquid Sorption-Enhanced Haber–Bosch Process

The use of a liquid sorbent in a traditional Haber-Bosch process enables significant improvements in energy efficiency and potential cost savings for arguably the most important chemical process on the planet. The approach presented in this report employs an incompressible liquid sorbent that absorbs and releases ammonia (NH 3 ) under specific conditions. To achieve this, we investigate reactions of ammonia and pure phosphoric acid (H 3 PO 4 , PA), which rapidly neutralize to form an equilibrated solution of monoammonium phosphate (MAP) and diammonium phosphate (DAP) that functions as a reversible and regenerable sorbent. Through intimate contact of the gas-phase Haber-Bosch reaction mixture with this liquid absorbent, complete equilibrium uptake may be achieved in an appropriately sized separator, and facile separation occurs through the use of independent liquid and gas phases. Following depressurization and release of the ammonia product, only the incompressible fluid needs to be repressurized and returned to the reactor. This study documents proof-of-concept absorption and desorption experiments carried out in 75 mL batch reactors, predominantly charged with precise MAP and DAP mixtures that equilibrate at process-relevant temperatures and pressures. We then assemble the first thermodynamic relationships that underlie this advantaged separation strategy, validated by reactive force field (ReaxFF) interatomic potential simulations, and benchmarked with traditional separation routes via process modeling and technoeconomic analysis. The scale of energy consumption in the century-old Haber-Bosch process is massive, and the elegant liquid sorption approach reported here offers opportunities to enhance its energy efficiency for the next frontier of ammonia synthesis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Plastic Waste Product Captures Carbon Dioxide in Nanometer Pores

We discuss, plastic waste (PW) and increasing atmospheric carbon dioxide (CO 2 ) levels are among the top environmental concerns presently facing humankind. With an ambitious 2050 zero-CO 2 emissions goal, there is a demand for economical CO 2 capture routes. Here we show that the thermal treatment of PW in the presence of potassium acetate yields an effective carbon sorbent with pores width of 0.7–1.4 nm for CO 2 capture. The PW to carbon sorbent process works with single or mixed streams of polyolefin plastics. The CO 2 capacity of the sorbent at 25 °C is 17.0 ± 1.1 wt % (3.80 ± 0.25 mmol g –1 ) at 1 bar and 5.0 ± 0.6 wt % (1.13 ± 0.13 mmol g –1 ) at 0.15 bar, and it regenerates upon reaching 75 ± 5 °C. The CO 2 capture cost from flue gas via this technology is estimated to be <$21 ton –1 CO 2 , much lower than competing CO 2 capture technologies. Hence, this PW-derived carbon material should find utility in the capture of CO 2 from point sources of high CO 2 emissions while providing a use for otherwise deleterious PW.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Surface Hydration of Porous Nickel Hydroxides Facilitates the Reversible Adsorption of CO 2 from Ambient Air

Direct air capture (DAC) under humid ambient conditions typically requires the use of organic components, with sorbents that are purely inorganic in composition for the most part operating hundreds of degrees above room temperature. In this work, we report porous metal hydroxides as a novel class of water-tolerant, oxidatively and hydrothermally stable low-temperature sorbents that exhibit competitive DAC working capacities of 1.25 mmol/g over 5 consecutive temperature swing adsorption–desorption cycles in the presence of steam and oxygen. Aqueous miscible organic solvent treatments are used to create highly porous structures with surface areas exceeding 700 m 2 /g that capture CO 2 in the form of bicarbonates under dry conditions, and carbonates under wet conditions. Water exerts a facilitative rather than an inhibiting effect on CO 2 binding, and the presence of hydrating multilayers serves to stabilize carbonate species akin to moisture swing adsorbents except for the fact that solvation results in a remarkable (upto 10-fold) increase, not decrease, in DAC capacity. High-valent doping with cerium is used to improve DAC capacities by amplifying surface basicity, evidencing porous nickel hydroxides specifically (and porous metal hydroxides more generally) as a novel class of robust, earth-abundant DAC sorbents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Integrated CO 2 Capture and Conversion to Formate with a Molecular Platinum Bis(diphosphine) Electrocatalyst

Carbon dioxide is a potentially valuable feedstock for carbon-based fuels or commodities but is only available in dilute streams. Many studies have focused on either the capture and concentration of CO 2 or the reduction of pure CO 2 streams. The direct reduction of sorbent-captured CO 2 in an integrated process would skip the energy-intensive CO 2 concentration and sorbent regeneration step. Herein, we report the electrocatalytic reduction of 1,3-bis(2,6-diisopropylphenyl)imidazolium-2-carboxylate (IPr·CO 2 ), which forms quantitatively from the reaction of sorbent 1,3-bis(2,6-diisopropylphenyl)imidazol-2-ylidene (IPr) with 10% and 0.04% CO 2 streams, by catalyst [Pt(dmpe) 2 ](PF 6 ) 2 (dmpe = 1,2-bis(dimethylphosphino)ethane) to formate with >70% Faradaic efficiencies. Unexpectedly, experimental studies indicate that the proton source phenol facilitates rapid decarboxylation of IPr·CO 2 to release CO 2 , which is the substrate for reduction. Kinetic studies determined the rate of hydride transfer from a catalytic intermediate [HPt(dmpe) 2 ](PF 6 ) to form the C–H bond in formate to be 0.22 M –1 s –1 . Further details on the mechanism, transition state energy, and structure for hydride transfer to CO 2 , a common step in CO 2 reduction, were explored using computational methods.

Chemistry↗
DOE OSTI2022

Carbon Capture Beyond Amines: CO 2 Sorption at Nucleophilic Oxygen Sites in Materials

Carbon capture and utilization or sequestration and direct air capture will be needed to reduce atmospheric levels of greenhouse gases over the next century. Current amine-based technologies bind CO 2 with high selectivities but suffer from poor oxidative and thermal stabilities. Herein, we discuss understudied sorbents based on oxygen nucleophiles, including metal oxides and hydroxides, hydroxide-containing polymers, and hydroxide-based metal–organic frameworks. In general, these materials display improved oxidative stabilities compared to traditional amine-based sorbents. Here, we outline the challenges and opportunities offered by these alternative sorbents for carbon capture applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Polymers in direct air capture: a mini review

The urgent need to mitigate climate change has intensified interest in direct air capture (DAC) technology, which targets extracting carbon dioxide (CO2) directly from the atmosphere. Among the various sorbents used in DAC, polymers have emerged as a promising solution, either as active sorbents or as structural supports for active DAC materials, due to their customizable properties, scalability and low cost. This mini-review investigates the latest trends in polymer-based materials for DAC and identifies critical research gaps, such as the need for thorough lifecycle assessments and in-depth studies on the degradation of polymeric materials. It also outlines future directions, emphasizing the importance of developing cost-effective, scalable and durable polymers that can perform efficiently across diverse climatic conditions, including the unique challenges presented by cold weather regions abundant in renewable energy. This mini-review aims to inform ongoing efforts in the design and utilization of polymeric sorbents, providing insights that could guide the development of economically viable and environmentally sustainable DAC technologies.

climate change↗
DOE OSTI2023

Selective Pb 2+ removal and electrochemical regeneration of fresh and recycled FeOOH

Heavy metal pollution is a key environmental problem. Selectively extracting heavy metals could accomplish water purification and resource recycling simultaneously. Adsorption is a promising approach with a facile process, adaptability for the broad concentration of feed water, and high selectivity. However, the adsorption method faces challenges in synthesizing high-performance sorbents and regenerating adsorbents effectively. FeOOH is an environmentally friendly sorbent with low-cost production on a large scale. Nevertheless, the selectivity behavior and regeneration of FeOOH are seldom studied. Therefore, we investigated the selectivity of FeOOH in a mixed solution of Co 2+ , Ni 2+ , and Pb 2+ and proposed to enhance the capacity of FeOOH and regenerate it by using external charges. Without charge, the FeOOH electrode shows a Pb 2+ uptake capacity of 20 mg/g. After applying a voltage of –0.2/+0.8 V, the uptake capacity increases to a maximum of 42 mg/g and the desorption ratio is 70%–80%. In 35 cycles, FeOOH shows a superior selectivity towards Pb 2+ compared with Co 2+ and Ni 2+ , with a purity of 97% ± 3% in the extracts. The high selectivity is attributed to the lower activation energy for Pb 2+ sorption. The capacity retentions at the 5 th and the 35 th cycles are ca. 80% and ca. 50%, respectively, comparable to the chemical regeneration method. With industrially exhausted granular ferric hydroxide as the electrode material, the system exhibits a Pb 2+ uptake capacity of 37.4 mg/g with high selectivity. Our work demonstrates the feasibility of regenerating FeOOH by charge and provides a new approach for recycling and upcycling FeOOH sorbent.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Strategies for design and synthesis of porous liquids toward carbon capture and separation

Porous liquids (PLs) represent a promising category of sorbents in carbon capture and separation capable of integrating the advantages of flowing liquid and porous solid systems. Well-defined pores were engineered into liquid sorbents via liquifying molecules with stiff interior voids, dissolving rigid porous hosts in flowing liquids, or dispersing porous frameworks in high steric hindrance solvents, producing type I, II, or III PLs, respectively. Unique features of PLs have triggered broad interest in exploring their applications in carbon capture and separation, in which diverse design strategies, synthesis approaches, and enhanced performance have been reported. Here, in this minireview, recent progress in the design, synthesis, and structural engineering of PLs and efforts towards the optimization of their carbon capture and separation behavior will be summarized, including the comparison between PLs with varied types. Porosity engineering into liquid sorbents provides opportunities to resolve challenging issues in conventional sorption and separation systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Adsorptive denitrogenation of model aviation fuel using mesoporous silica in a packed bed adsorption system

This study aims to understand the effects of system process parameters such as flow rate, adsorbent particle size, and use of recycled adsorbent on denitrogenation performance of a model fuel using mesoporous silica gel. The goal is to reduce the nitrogen content of the model fuel from 1500 parts per million to single-digit ppm to meet ASTM specifications for drop-in fuels. This work was done with the intent of applying adsorptive denitrogenation to sustainable aviation fuel (SAF) product fractions produced via hydrothermal liquefaction (HTL). The adsorption performance of the silica is evaluated via packed column breakthrough data, with data generated from collecting from the column outlet and quantifying nitrogen content via gas chromatography. Select experiments use a significantly larger (2.5x column diameter and length) column to demonstrate linear scalability of the process. Thermogravimetric analysis data is collected to evaluate the effects of thermal calcination as a sorbent regeneration method. Effects of a more complex feed are also investigated using a known reference fuel with additional added nitrogen containing compounds. The results presented in this work successfully demonstrate up to 99.8 % removal of NCCs from a model fuel fraction at an original NCC concentration of approximately 1500 ppm to single-digit parts per million after treatment. We also examine calcination of sorbent materials to remove the adsorbed species to enable sorbent reuse and minimize waste generation and show that the calcined material can be reused up to 5 cycles with reduced adsorption capacity. Overall, this work indicates that adsorptive denitrogenation using silica gel is a viable solution to enable the integration of HTL-derived aviation fuels into existing fuel infrastructure.

Adsorption techniques↗
DOE OSTI2021

Cs absorption capacity and selectivity of crystalline and amorphous Hf and Zr phosphates

Removal of radioactive Cs from sodium-rich solutions is a technical challenge that goes back to post World War II nuclear waste storage and treatment; and interest in this topic was reinvigorated by the Fukushima-Daiichi nuclear power plant disaster, 10 years ago. Since the 1960's there has been considerable focus on layered Zr phosphates as robust inorganic sorbents for separation of radionuclides such as Cs. Here we present synthesis and characterization, and direct comparison of Cs sorption capacity and selectivity of four related materials: 1) crystalline α-Zr phosphate and α-Hf phosphate, and 2) amorphous analogues of these. Powder X-ray diffraction, thermogravimetry, solid-state 31P magic angle spinning nuclear magnetic resonance (MAS-NMR) spectroscopy, and compositional analysis (inductively coupled plasma optical emission spectroscopy and mass spectroscopy, ICP OES and ICP MS) provided formulae; respectively M(HPO4)2∙1H2O and M(HPO4)2∙4H2O (M = Hf, Zr) for crystalline and amorphous analogues. Maximum Cs loading, competitive Cs-Na selectivity and maximum Cs-Na loading followed by the above characterizations plus 133Cs MAS-NMR spectroscopy revealed that amorphous analogues are considerably better Cs-sorbents (based on maximum Cs-loading and selectivity over Na) than the well-studied crystalline Zr-analogue. Additionally, crystalline α-Hf phosphate is better Cs-sorbent than crystalline α-Zr phosphate. All these studies consistently show that Hf phosphate is less crystallize than Zr phosphate, when obtained under similar or identical synthesis conditions. We attribute this to lower solubility of Hf phosphate compared to Zr phosphate, preventing ‘defect healing’ during the synthesis process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Efficient Removal of Per- and Polyfluoroalkyl Substances from Water with Zirconium-Based Metal–Organic Frameworks

Per- and polyfluoroalkyl substances (PFASs) are an emerging class of contaminants raising increased levels of concern due to their toxic, bioaccumulative, and persistent nature. Current solutions for removing PFAS from contaminated water rely on adsorption-based methods where commonly used sorbents, for example, activated carbons and ion-exchange resins, exhibit low adsorption capacity and a long equilibration time. Motivated by the generally deficient performance of these current materials, this work addresses the need for the discovery of advanced sorbents for high capacity and efficient PFAS removal. The zirconium-based metal–organic framework (MOF) NU-1000 was characterized for the adsorption of three perfluorosulfonic acids (PFSAs, C4–C8) and six perfluorinated carboxylic acids (PFCAs, C1–C9) from aqueous solutions. Here, the results indicate that NU-1000 exhibits outstanding adsorption capacities of 400–620 mg/g for PFSAs and 201–604 mg/g for PFCAs coupled with ultrafast adsorption kinetics featuring equilibrium times of <1 min. Complementary density functional theory calculations reveal that the PFAS@MOF adsorption mechanism is dominated by a combination of hydrogen bonding, electrostatic, and hydrophobic non-covalent PFAS–MOF interactions. Excellent regeneration and reusability characteristics were found, particularly nearly quantitative removal and recovery rates of NU-1000 after five consecutive adsoption and desorption cycles of PFAS. Additional adsorption testing using PFAS-contaminated groundwater samples obtained from U.S. Air Force bases revealed impressive PFAS removal rates of 75–98% within 10 min regardless of the presence of co-contaminants. To the best of our knowledge, the suite of herein presented PFAS sorption characteristics—capacity, kinetics, regeneration, and reusability—significantly outperforms other current sorbents, rendering NU-1000 as a promising platform for the rapid and effective removal of PFAS from aqueous media.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Modeling and Optimization of a Rotating Packed Bed Contactor with a Tetraamine-Appended Metal−Organic Framework for CO 2 Capture

A potential contactor technology for sorbent-based CO 2 capture is the rotating packed bed that contains separate sections for continuous adsorption and desorption. A heat exchanger can be embedded to remove heat in the adsorption section and add heat in the desorption section. In this work, we develop a two-dimensional (2D) model of a rotating packed bed for use in CO 2 capture applications. Mass and energy balances for the model are developed based on a Ljungström-type air preheater, which accounts for the counter-current axial flow of gas phases in separate sections of the bed and the rotation of a solid sorbent, which cycles between adsorption and desorption sections. The sorbent used for this analysis is the tetraamine-appended metal−organic framework Mg 2 (dobpdc)(3−4− 3), chosen for its stability and affinity for CO 2 at low partial pressures, such as those from a natural gas power plant source. An optimization problem is solved that considers the trade-off between maximizing the productivity of the bed and minimizing energy consumption. Maximum productivity and minimum energy are found to be 8.53 kg/h/m 3 and 3.84 MJ/kg, respectively, when these objectives are optimized independently. It is observed that the flue gas pressure and bed rotational speed are the desired operating variables to vary for model-based design of experiments to reduce uncertainty in parameter estimation, as these two variables yielded the most information content based on the Fisher information matrix.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2026

Breakthrough Zn(II) Catalyst for Direct Air Capture Employing CO 2 Hydration

Direct air capture (DAC) represents a vital technology for atmospheric CO₂ remediation, but few studies have tested catalysts at dilute atmospheric CO₂ concentrations. Inspired by the carbonic anhydrase metalloenzyme, we report a catalytic DAC strategy employing robust zinc(II) enzyme mimics that enable efficient CO₂ sequestration pathways. A catalyst-mediated CO₂ hydration cycle in aqueous sorbents facilitates accelerated capture from dilute atmospheric air, thereby addressing the kinetic limitations observed in carbonate-based systems. Our developed complexes [ZnC1] and [ZnC2] enhance capture rates up to two-fold at millimolar concentrations and improve CO₂ mass transfer by 40-60% in 1 M K₂CO₃ sorbent under ambient conditions. These bench-stable, earth-abundant zinc catalysts operate effectively under dilute CO₂ concentrations, overcoming the kinetic limitations of conventional carbonate-based sorbents. As a result, mechanistic studies support a biomimetic catalytic cycle that facilitates rapid CO₂ conversion, demonstrating that catalyst-assisted DAC can enable energy-efficient, scalable carbon capture technologies.

Atmospheric chemistry↗
DOE OSTI2026

Moisture-driven CO 2 direct air capture and delivery for cultivating cyanobacteria

This study demonstrates a low-energy system that passively captures CO₂ from ambient air using reusable solid sorbents and delivers it directly into alkaline cultivation media to support the growth of cyanobacteria, from laboratory flasks to outdoor raceway ponds. While long-term operation revealed challenges including biofouling and sorbent degradation, the results suggest that with improved sorbent durability, this approach could provide a scalable source of atmospheric carbon for producing sustainable fuels, proteins, natural colorants, and other bioproducts.

09 BIOMASS FUELS↗
DOE OSTI2021

Understanding the Adsorption of Rare-Earth Elements in Oligo-Grafted Mesoporous Carbon

Rare-earth elements (REEs) are 17 elements of the periodic table primarily consisting of lanthanides. In modern society, the usage of REEs is ubiquitous in almost all modern gadgets and therefore efficient recovery and separation of REEs are of high importance. Selective adsorption and chelation of REEs in solid sorbents is a unique and sustainable process for their recovery. In this work, single-stranded oligos with 100 units of thymine were grafted onto carboxylated mesoporous carbon to synthesize a sorbent with phosphorus and oxygen functionalities. Additionally, the sorbent was characterized by X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, and scanning electron microscopy-energy-dispersive X-ray spectroscopy. Three different REEs with varying atomic radii and densities, Lu, Dy, and La, were adsorbed onto the carbon from aqueous solutions. It was observed that the adsorbed amounts increased with the increase in the atomic radius or decrease in the atomic density. Calculation of the distribution coefficients for all the equilibrium adsorption amounts suggested that adsorption is more effective in the lower concentration region. The L 3 -edge X-ray absorption near-edge structure confirmed a 3+ oxidation state of REEs in the adsorbed phase. Extended X-ray absorption fine structure (EXAFS) confirmed the binding of REEs with oxygen functionalities in the adsorbed phase. The radial distribution functions calculated from the EXAFS data suggest a longer RE–O distance for La compared to those for Lu and Dy. The coordination numbers and Debye–Waller factors have typical values of about 8–9 atoms and 0.01–0.02 Å 2 , respectively.

36 MATERIALS SCIENCE↗