Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “separator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

A numerical investigation of crossflow separation on a three-caliber tangent ogive-cylinder

A parabolized Navier-Stokes code was used to calculate laminar crossflow separation on a simple body of revolution. Convergence lines were defined as lines on which skin-friction lines converge and were visually determined from the computed skin-friction patterns. These convergence lines were shown to be limit lines and not envelopes. Examination of crossflow cuts of streamtubes which encircled the body indicated that crossflow separation (defined by a fold in the streamtube) began after the onset of negative crossflow velocities but before a convergence line could be determined from the skin-friction patterns. There were no rapid changes or extrema in the pressure, skin-friction, vorticity, or flow-angle distributions that indicated where separation occurred. Instead, crossflow separation developed gradually and involved an extended region of the surface.

Yates, Leslie A.↗
NASA NTRS1987

Grace DAKASEP alkaline battery separator

The Grace DAKASEP separator was originally developed as a wicking layer for nickel-zinc alkaline batteries. The DAKASEP is a filled non-woven separator which is flexible and heat sealable. Through modification of formulation and processing variables, products with a variety of properties can be produced. Variations of DAKASEP were tested in Ni-H2, Ni-Zn, Ni-Cd, and primary alkaline batteries with good results. The properties of DAKASEP which are optimized for Hg-Zn primary batteries are shown in tabular form. This separator has high tensile strength, 12 micron average pore size, relatively low porosity at 46-48 percent, and consequently moderately high resistivity. Versions were produced with greater than 70 percent porosity and resistivities in 33 wt percent KOH as low as 3 ohm cm. Performance data for Hg-Zn E-1 size cells containing DAKASEP with the properties shown in tabular form, are more reproducible than data obtained with a competitive polypropylene non-woven separator. In addition, utilization of active material is in general considerably improved.

Giovannoni, R. T.↗
NASA NTRS1988

A flow visualization study of the leading edge separation bubble on a NACA 0012 airfoil with simulated glaze ice

As a part of an ongoing research in aircraft icing, the leading edge separation bubble on a NACA 0012 model with a 5 min simulated glaze ice was investigated. The flow visualization methods using oil, tuft, splitter plate, smoke, and liquid crystals were employed to get reattachment line data for the leading edge separation bubble on both surfaces of the airfoil. On the upper surface, the separation bubble was found to grow larger with increasing angles of attack and reduce in size with decreasing angle of attack. On the lower surface, the bubble was found to grow larger with increasing negative angles of attack and reduce in size with increasing angles of attack. The separated flow fails to reattach beyond 6° for the upper surface and -5° for the loser surface. Their results of this study compared well with those of other experiments and computational results.

Aircraft icing↗
NASA NTRS1988

Fluctuations and massive separation in three-dimensional shock-wave/boundary-layer interactions

Shock-wave unsteadiness was observed in rapidly compressed supersonic turbulent boundary layer flows with significant separation. A Mach 2.85 shock-wave/turbulent boundary layer flow was set up over a series of cylinder-flare bodies in the High Reynolds Number Channel 1. The transition from fully attached to fully separated flow was studied using axisymmetric flares with increasing compression angles. In the second phase, the 30 deg flare was inclined relative to the cylinder axis, so that the effect on a separated flow of increasing 3 dimensionality could be observed. Two 3-D separated cases are examined. A simple conditional sampling technique is applied to the data to group them according to an associated shock position. Mean velocities and turbulent kinetic energies, computed from the conditionally samples data, are compared to those from the unsorted data and to computed values. Three basic questions were addressed: can conditional sampling be used to provide snapshots of the flow; are averaged turbulence quantities dominated by the bimodal nature of the interaction; and is the shock unsteadiness really important to computational accuracy.

Kussoy, M. I.↗
NASA NTRS1988

The effect of acoustic forcing on trailing edge separation and near wake development of an airfoil

An experimental study was conducted to investigate the effect of acoustic forcing on flow fields near the trailing edge of a symmetric airfoil at zero angle of attack. At low chord Reynolds numbers, the boundary layers separate from the surfaces in the rear part of the airfoil and create recirculation regions near the trailing edge. It is shown that with the introduction of acoustic forcing through a slot in the vicinity of the separation point, periodic large-scale structures are generated in the trailing edge region. Significant reduction of trailing edge separation is achieved. It is also found that the most effective forcing frequency to control trailing edge separation is the wake vortex shedding frequency. As a result of forcing, applied only on the upper surface, the upper boundary layer is accelerated and the flow over the lower surface decelerated. Consequently, an asymmetric wake is formed. The results presented indicate that the development of the near wake varies with forcing conditions.

Huang, L. S.↗
NASA NTRS1989

Measuring Laminar-Separation Bubbles On Airfoils

Nonintrusive multielement heat-transfer sensor overcomes limitations of previous methods. New technique determines simultaneously extent of laminar boundary layer and locations of laminar separation, transition in separated layer, and turbulent reattachment. In tests, only small amounts of heat introduced, and heated thin films caused little disturbance to shear layer or to each other. Promising tool for measurements of stability of laminar boundary layers, separated shear layers, and transitional separation bubbles. Simple and capable of providing comprehensive picture of state of shear flow along entire surface. Significant savings in tunnel (or flight) test time with corresponding savings in cost.

Stack, John P.↗
NASA NTRS1989

Restrictive loads powered by separate or by common electrical sources

In designing a multiple load electrical system, the designer may wish to compare the performance of two setups: a common electrical source powering all loads, or separate electrical sources powering individual loads. Three types of electrical sources: an ideal voltage source, an ideal current source, and solar cell source powering resistive loads were analyzed for their performances in separate and common source systems. A mathematical proof is given, for each case, indicating the merit of the separate or common source system. The main conclusions are: (1) identical resistive loads powered by ideal voltage sources perform the same in both system setups, (2) nonidentical resistive loads powered by ideal voltage sources perform the same in both system setups, (3) nonidentical resistive loads powered by ideal current sources have higher performance in separate source systems, and (4) nonidentical resistive loads powered by solar cells have higher performance in a common source system for a wide range of load resistances.

Appelbaum, J.↗
NASA NTRS1988

Fluctuations and massive separation in three-dimensional shock-wave/boundary-layer interactions

Shock-wave unsteadiness was observed in rapidly compressed supersonic turbulent boundary layer flows with significant separation. A Mach 2.85 shock-wave/turbulent boundary layer flow was set up over a series of cylinder-flare bodies in the High Reynolds Number Channel 1. The transition from fully attached to fully separated flow was studied using axisymmetric flares with increasing compression angles. In the second phase, the 30-deg flare was inclined relative to the cylinder axis, so that the effect on a separated flow of increasing three-dimensionality could be observed. Two 3-D separated cases are examined. A simple conditional sampling technique is applied to the data to group them according to an associated shock position. Mean velocities and turbulent kinetic energies, computed from the conditionally sampled data, are compared to those from the unsorted data and to computed values. Three basic questions were addressed: can conditional sampling be used to provide snapshots of the flow; are averaged turbulence quantities dominated by the bimodal nature of the interaction; and is the shock unsteadiness really important to computational accuracy.

Kussoy, M. I.↗
NASA NTRS1989

Separation shock motion in fin, cylinder, and compression ramp - Induced turbulent interactions

In conjunction with new experimental results at Mach 5, an examination has been made of published data on unsteadiness of shock-induced turbulent boundary-layer separation. The data are all wall pressure fluctuation measurements made under the unsteady separation shock and are from interactions induced by compression ramps, blunt and sharp fins, and circular cylinders. There is little evidence of a link between the separation shock zero-crossing frequency and characteristic frequency of the incoming boundary layer. The low shock frequencies and low shock speeds, and the trends with changes in model geometric parameters and incoming boundary layer, suggest that turbulent or global fluctuations at the upstream boundary of the separated flow drive the shock motion.

Dolling, D. S.↗
NASA NTRS1989

Analysis of low Reynolds number separation bubbles using semiempirical methods

The formation and growth of transitional separation bubbles can significantly affect boundary-layer development on airfoils operating at low chord Reynolds numbers. Of primary concern is the change in boundary-layer thickness between laminar separation and turbulent reattachment. This can be estimated using semiempirical methods, such as the one devised by Horton (1968), which are based on solutions to the integral forms of the boundary-layer equations. The applicability of these methods at low Reynolds numbers was investigated using hot-wire measurements of bubbles formed on an NACA 66(3)-018 airfoil at chord Reynolds numbers of 50,000-200,000. The momentum thickness growth between separation and transition was found to be similar to that predicted for a laminar half-jet and appears to be influenced by the momentum thickness Reynolds number at separation. This parameter also was found to have a noticeable effect on the Reynolds number based on the length of a bubble's laminar portion.

Schmidt, Gordon S.↗
NASA NTRS1989

Simultaneous detection of separation and transition in surface shear layers

Flush-mounted hot-film gages have proved effective in detecting boundary-layer transition and in measuring skin friction but with limited success in detecting laminar separation and reattachment. The development of multielement micro hot-film sensors, and the recent discovery of the phase reversal phenomena associated with low-frequency dynamic shear stress signals across regions of laminar separation and turbulent reattachment, have made it possible to simultaneously and unambiguously detect these surface shear layer characteristics. Experiments were conducted on different airfoils at speeds ranging from low subsonic to transonic speeds to establish the technique for incompressible and compressible flow applications. The multielement dynamic shear stress sensor technique was successfully used to detect laminar separation, turbulent reattachment, as well as, shock induced laminar and turbulent separation.

Mangalam, Siva M.↗
NASA NTRS1991

Laminar-Separation Sensor

Reduction of viscous drag on airplanes explores limits of practical applications of natural laminar flow. Wind-tunnel and flight tests conducted to explore abilities of hot-film sensors to identify separation of laminar flow as principal mode of amplification of instability leading to transition from laminar to turbulent flow. Two different laminar-separation-sensor configurations developed and used to detect boundary-layer transitions. Results show hot-film laminar-separation-sensor technique viable means for detecting existence of transition as well as for indicating reversed flow in laminar-separation bubble. Refinement of sensor configurations provides tools necessary to explore, in all speed regimes, practical limits of laminar-flow applications and viscous-drag-reduction technology.

Manuel, G. S.↗
NASA NTRS1991

High temperature seals between ceramic separation membranes and super-alloy housing

One of the concepts for oxygen production from Martian atmospheric carbon dioxide involves the use of tubular electrochemical membranes for oxygen separation. The tubular configuration offers the advantage of being able to separate the oxygen at pressures of up to 500 psi, thereby eliminating the need for a pre-liquefaction oxygen compressor. A key technology that has to be developed in order for the electrochemical separator to combine as a compressor is a high temperature static seal between the ceramic separation cell and the nickel-based super-alloy tube. Equipment was designed and fabricated to test the seals. Efforts are under way to develop a finite element model to study the thermal stresses at the joints and on the seal, and the optimal shape of the seal. The choice of seal materials and the technique to be used to fabricate the seals are also being investigated.

Honea, G.↗
NASA NTRS1992

Fully nonlinear Goertler vortices in constricted channel flows and their effect on the onset of separation

The development of fully nonlinear Goertler vortices in high Reynolds number flow in a symmetrically constricted channel is investigated. Attention is restricted to the case of 'strongly' constricted channels considered by Smith and Daniels (1981) for which the scaled constriction height is asymptotically large. Such flows are known to develop a Goldstein singularity and subsequently become separated at some downstream station past the point of maximum channel constriction. It is shown that these flows can support fully nonlinear Goertler vortices, of the form elucidated by Hall and Lakin (1988), for constrictions which have an appreciable region of local concave curvature upstream of the position at which separation occurs. The effect on the onset of separation due to the nonlinear Goertler modes is discussed. A brief discussion of other possible nonlinear states which may also have a dramatic effect in delaying (or promoting) separation is given.

Denier, James P.↗
NASA NTRS1992

Measurements in a leading-edge separation bubble due to a simulated airfoil ice accretion

The separation bubble formed on an airfoil at low Reynolds number behind a simulated leading-edge glaze ice accretion is studied experimentally. Surface pressure and split hot-film measurements as well as flow visualization studies of the bubble reattachment point are reported. The simulated ice generates an adverse pressure gradient that causes a laminar separation bubble of the long bubble type to form. The boundary layer separates at a location on the ice accretion that is independent of angle of attack and reattaches at a downstream location 5-40 percent chord behind the leading edge, depending on the angle of attack. Velocity profiles show a large region of reverse flow that extends up from the airfoil surface as much as 2.5 percent chord. After reattachment, a thick distorted turbulent boundary layer exists. The separation bubble growth and reattachment are clearly seen in the plots of boundary-layer momentum thickness vs surface distance. Local minima and maxima in the boundary-layer momentum thickness development compare well with the shear layer transition point as indicated by the surface pressures and the reattachment point as measured from surface oil flow, respectively.

Bragg, M. B.↗
NASA NTRS1987

Confined separated-swirling flows in diffusing ducts

The objective is to establish a detailed experimental data base for evaluation of Navier-Stokes codes for confined separated flows in diffusing s-ducts. The computational thrusts include the following: (1) extension and validation of the LeRC parabolized Navier-Stokes solver, PEPSIG, into the separated flow regime using 'flare' type approximations; (2) evaluation and extensions of state-of-the-art turbulence models for confined separated flow with and without swirl; and (3) evaluation and validation of LeRC time marching 3-D Navier-Stokes code, PROTEUS, into confined separate flow regime. Various aspects of the study are presented in viewgraph form.

Anderson, Bernhard H.↗
NASA NTRS1993

Aerodynamics of powered missile separation from F/A-18 aircraft

A 3D dynamic 'chimera' algorithm that solves the thin-layer Navier-Stokes equations over multiple moving bodies was modified to numerically simulate the aerodynamics, missile dynamics, and missile plume interactions of a missile separating from a generic wing and from an F/A-18 aircraft in transonic flow. The missile is mounted below the wing for missile separation from the wing and on the F/A-18 fuselage at the engine inlet side for missile separation from aircraft. Static and powered missile separation cases are considered to examine the influence of the missile and plume on the wing and F/A-18 fuselage and engine inlet. The aircraft and missile are at two degrees angle of attack, Reynolds number of 10 million, freestream Mach number of 1.05 and plume Mach number of 3.0. The computational results show the details of the flow field.

Ahmad, J. U.↗
NASA NTRS1992

Visualization of entry flow separation for oscillating flow in tubes

Neutrally buoyant helium-filled soap bubbles with laser illumination are used to document entry flow separation for oscillating flow in tubes. For a symmetric entry case, the size of the separation zone appears to mildly depend on Reynolds number in the acceleration phase, but is roughly Reynolds number independent in the deceleration phase. For the asymmetric entry case, the separation zone was larger and appeared to grow somewhat during the deceleration phase. The separation zones for both entry geometry cases remain relatively small throughout the cycle. This is different from what would be observed in all-laminar, oscillator flows and is probably due to the high turbulence of the flow, particularly during the deceleration phase of the cycle.

Qiu, Songgang↗