Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “receiver synchronization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Precise terrestrial time: A means for improved ballistic missile guidance analysis

An approach developed to improve the ground instrumentation time tagging accuracy and adapted to support the Minuteman ICBM program is desired. The Timing Insertion Unit (TIU) technique produces a telemetry data time tagging resolution of one tenth of a microsecond, with a relative intersite accuracy after corrections and velocity data (range, azimuth, elevation and range rate) also used in missile guidance system analysis can be correlated to within ten microseconds of the telemetry guidance data. This requires precise timing synchronization between the metric and telemetry instrumentation sites. The timing synchronization can be achieved by using the radar automatic phasing system time correlation methods. Other time correlation techniques such as Television (TV) Line-10 and the Geostationary Operational Environmental Satellites (GEOS) terrestial timing receivers are also considered.

Ehrsam, E. E.↗
NASA NTRS1979

Searching for nonsolar planets

The use of infrared techniques to search for nonsolar planets is examined and compared with other possible methods. Long focus astrometry, spectroscopic radial velocity measurements and spaceborne apodization all use visible light and need further refinement to be practical. Infrared offers an advantage of about 10 to the 5th over visible light as regards the ratio of power received from star and planet. Long baseline infrared interferometry from earth orbit could place an interferometric null on the star to enhance planetary radiation and a spinning interferometer would modulate planetary emission to permit synchronous detection; such an interferometer is illustrated. The limit to sensitivity would be set by thermal radiation to the detector and the infrared component of zodiacal light.

Bracewell, R. N.↗
NASA NTRS1983

A system for the simulation and evaluation of satellite communication networks

With the emergence of a new era in satellite communications brought about by NASA's thrust into the Ka band with multibeam and onboard processing technologies, new and innovative techniques for evaluating these concepts and systems are required. To this end, NASA, in conjunction with its extensive program for advanced communications technology development, has undertaken to develop a concept for the simulation and evaluation of a complete communications network. Incorporated in this network will be proof of concept models of the latest technologies proposed for future satellite communications systems. These include low noise receivers, matrix switches, baseband processors, and solid state and tube type high power amplifiers. To accomplish this, numerous supporting technologies must be added to those aforementioned proof of concept models. These include controllers for synchronization, order wire, and resource allocation, gain compensation, signal leveling, power augmentation, and rain fade and range delay simulation. Taken together, these will be assembled to comprise a system capable of addressing numerous design and performance questions. The simulation and evaluation system as planned will be modular in design and implementation, capable of modification and updating to track and evaluate a continuum emerging concepts and technologies.

Bagwell, J. W.↗
NASA NTRS2000

Lidar Remote Sensing System

A lidar remote sensing system wherein a laser signal is transmitted along an optical path through a telescope having a primary and secondary mirrors and a rotating prism at the telescope output. When the reflected signal from the target is received it is passed back through the system to a detector, where it is heterodyned with a signal from a local oscillator to detect Doppler frequency shifts in the returned signal. Since the prism is rotating, the prism will be at one position when the signal is transmitted and at another when the returned signal is received. This causes the reflected signal to be off the optical path, reducing the power of the returned signal. To correct this problem a de-rotator or prism is mounted for rotation, in synchronism with the rotating prism. about the optical path in a position to intersect the returned beam and refract it back onto the optical path to reduce the power loss in the returned signal.

Michael J Kavaya↗
NASA NTRS1973

Clock synchronization experiments performed via the ATS-1 and ATS-3 satellites.

Clock synchronization experiments were carried out May 10 to June 10, 1971, via the ATS-1 and ATS-3 geostationary satellites between the NASA tracking stations at Rosman, N.C., and Mojave, Calif., in order to determine the offset and the relative drift rate between the two station clocks. Pulses at C band with very sharp risetime and of 10 microsec duration were exchanged by the two stations through the dual transponders of the satellites. At each station, a time-interval counter was started by the transmitted pulse and stopped by the pulse received via satellite from the other station. The probable error of the clock offset as measured by the counter is 10 msec. A very long baseline interferometer experiment was also performed between the two stations at the same time and provided independent clock-offset data to check the accuracy of the time-synchronization experiment.

Ramasastry, J.↗
NASA NTRS1995

High accuracy time transfer synchronization

In July 1994, the U.S. Naval Observatory (USNO) Time Service System Engineering Division conducted a field test to establish a baseline accuracy for two-way satellite time transfer synchronization. Three Hewlett-Packard model 5071 high performance cesium frequency standards were transported from the USNO in Washington, DC to Los Angeles, California in the USNO's mobile earth station. Two-Way Satellite Time Transfer links between the mobile earth station and the USNO were conducted each day of the trip, using the Naval Research Laboratory(NRL) designed spread spectrum modem, built by Allen Osborne Associates(AOA). A Motorola six channel GPS receiver was used to track the location and altitude of the mobile earth station and to provide coordinates for calculating Sagnac corrections for the two-way measurements, and relativistic corrections for the cesium clocks. This paper will discuss the trip, the measurement systems used and the results from the data collected. We will show the accuracy of using two-way satellite time transfer for synchronization and the performance of the three HP 5071 cesium clocks in an operational environment.

Wheeler, Paul J.↗
NASA NTRS1974

Simultaneous master-slave Omega pairs

Master-slave sequence ordering of the Omega system is suggested as a method of improving the pair geometry for low-cost receiver user benefit. The sequence change will not affect present sophisticated processor users other than require new labels for some pair combinations, but may require worldwide transmitter operators to slightly alter their long-range synchronizing techniques.

Burhans, R. W.↗
NASA NTRS1975

Satellite laser ranging work at the Goddard Space Flight Center

The paper describes the satellite laser ranging system at the Goddard Space Flight Center, its range and accuracy capabilities, and planned improvements for future systems. Major subsystems are described, including the laser, optical/mechanical, receiver, computer/software, timing, and laser data preprocessing subsystems. Operational considerations are examined, with attention given the mobile station layout, manpower requirements, and transportability. System performance is considered, with emphasis on system accuracy (calibration, stability, clock synchronization, atmospheric propagation correction) and range capability.

Mcgunigal, T. E.↗
NASA NTRS1984

A system for the simulation and evaluation of satellite communication networks

With the emergence of a new era in satellite communications, brought about by NASA's thrust into the Ka band with multibeam and onboard processing technologies, new and innovative techniques for evaluating these concepts and systems are required. To this end, NASA, in conjunction with its extensive program for advanced communications technology development, has undertaken to develop a concept for the simulation and evaluation of a complete communications network. Incorporated in this network will be proof-of-concept models of the latest technologies proposed for future satellite communications systems. These include low noise receivers, matrix switches, baseband processors, and solid state and tube type high power amplifiers. To accomplish this, numerous supporting technologies must be added to those aforementioned proof-of-concept models. These include controllers for synchronization, order wire, resource allocation, gain compensation, signal leveling, power augmentation, and rain fade and range delay simulation. Taken together, these will be assembled to comprise a system capable of addressing numerous design and performance questions. The simulation and evaluation system, as planned, will be modular in design and implementation, capable of modification and updating to track and evaluate a continuum of emerging concepts and technologies. Previously announced in STAR as N84-13400

Bagwell, J. W.↗
NASA NTRS2018

High-Rate Ka-Band Modulator for the NISAR Mission

In order to meet ever-increasing data return requirements, more satellites are using the near-Earth Ka-band (25.5 – 27.0 GHz) to achieve higher downlink rates. The paper discusses the Universal Space Transponder - Ka-band Modulator (UST-KaM) developed at the NASA Jet Propulsion Laboratory for the NASA-ISRO SAR (NISAR) mission, which is capable of transmitting up to 1.74 Gbps with 7/8 LDPC encoding. The UST-KaM utilizes OQPSK with both baseband and RF filtering to contain the 1 Gsps transmission spectrum within the 1.5 GHz Ka-band, even with the use of an external, saturated amplifier. Due to the high data rates involved, several technical hurdles were overcome in both the digital and RF designs. The UST-KaM is a software defined radio with two digital circuit board assemblies: a low speed housekeeper board for commanding and telemetry, and a high-rate signal processing board known as the Signal Processing Module (SPM). The SPM receives data from the spacecraft via a SERDES interface at up to 2 Gbps, processes and encodes the data using a Xilinx Virtex-5 FPGA, and produces 1 Gsps OQPSK I and Q waveforms via synchronized, multiplexed DACs. The RF Electronics in the UST-KaM employ a heterodyne architecture in which the I/Q digital waveforms are filtered and then up-converted using a sub-harmonic IQ mixer. The LO of the converter, which is included in the exciter assembly, is at 13.125GHz, and the RF output is a 26.25GHz carrier which is modulated with the OQPSK waveforms. The output of the mixer is then filtered using low loss quartz thinfilm edge coupled Chebyshev filters and amplified through a series of low gain Ka-Band amplifiers. The exciter assembly also has a 2GHz, low-phase-noise, PLL synthesizer to supply the clock to the DACs for the high rate digital waveforms.

Spurgers, Carl↗
NASA NTRS1977

Transport of lunar material to the sites of the colonies

An 'existence proof' is attempted for the feasibility of transport of lunar material to colonies in space. Masses of lunar material are accelerated to lunar escape by a tracked magnetically levitated mass driver; aim precision is to 1 km miss distance at L5 per mm/sec velocity error at the lunar surface. Mass driver design and linear synchronous motor drive design are discussed; laser-sensed checkpoints aid in velocity and directional precision. Moon-L5 trajectories are calculated. The design of the L5 construction station, or 'catcher vehicle,' is described; loads are received by chambers operating in a 'Venus flytrap' mode. Further research studies needed to round out the concept are listed explicitly.

Heppenheimer, T. A.↗
NASA NTRS1979

Submicrosecond comparison of intercontinental clock synchronization by VLBI and the NTS satellite

The intercontinental clock synchronization capabilities of Very Long Baseline Interferometry (VLBI) and the Navigation Technology Satellite (NTS) were compared in May 1978 by using both methods to synchronize the cesium clocks at the NASA Deep Space Net complexes at Madrid, Spain, and Goldstone, California. The VLBI experiments used the Wideband VLBI Data Acquisition System. The Navigation Technology Satellites were used with NTS Timing Receivers developed by the Goddard Space Flight Center. The two methods agreed at about the one-half microsecond level. The VLBI system also obtained long-term stability information on the HP5061A004 cesium standards by measuring delta T/T over four 3- to 4-day intervals, obtaining stability estimates of (1 + or - 1)x10 to the -13th power for the combined timing systems.

Hurd, W. J.↗
NASA NTRS1980

Satellite communication performance evaluation: Computational techniques based on moments

Computational techniques that efficiently compute bit error probabilities when only moments of the various interference random variables are available are presented. The approach taken is a generalization of the well known Gauss-Quadrature rules used for numerically evaluating single or multiple integrals. In what follows, basic algorithms are developed. Some of its properties and generalizations are shown and its many potential applications are described. Some typical interference scenarios for which the results are particularly applicable include: intentional jamming, adjacent and cochannel interferences; radar pulses (RFI); multipath; and intersymbol interference. While the examples presented stress evaluation of bit error probilities in uncoded digital communication systems, the moment techniques can also be applied to the evaluation of other parameters, such as computational cutoff rate under both normal and mismatched receiver cases in coded systems. Another important application is the determination of the probability distributions of the output of a discrete time dynamical system. This type of model occurs widely in control systems, queueing systems, and synchronization systems (e.g., discrete phase locked loops).

Omura, J. K.↗
NASA NTRS1992

Subnanosecond GPS-based clock synchronization and precision deep-space tracking

Interferometric spacecraft tracking is accomplished by the Deep Space Network (DSN) by comparing the arrival time of electromagnetic spacecraft signals at ground antennas separated by baselines on the order of 8000 km. Clock synchronization errors within and between DSN stations directly impact the attainable tracking accuracy, with a 0.3-nsec error in clock synchronization resulting in an 11-nrad angular position error. This level of synchronization is currently achieved by observing a quasar which is angularly close to the spacecraft just after the spacecraft observations. By determining the differential arrival times of the random quasar signal at the stations, clock offsets and propagation delays within the atmosphere and within the DSN stations are calibrated. Recent developments in time transfer techniques may allow medium accuracy (50-100 nrad) spacecraft tracking without near-simultaneous quasar-based calibrations. Solutions are presented for a worldwide network of Global Positioning System (GPS) receivers in which the formal errors for DSN clock offset parameters are less than 0.5 nsec. Comparisons of clock rate offsets derived from GPS measurements and from very long baseline interferometry (VLBI), as well as the examination of clock closure, suggest that these formal errors are a realistic measure of GPS-based clock offset precision and accuracy. Incorporating GPS-based clock synchronization measurements into a spacecraft differential ranging system would allow tracking without near-simultaneous quasar observations. The impact on individual spacecraft navigation-error sources due to elimination of quasar-based calibrations is presented. System implementation, including calibration of station electronic delays, is discussed.

Dunn, C. E.↗
NASA NTRS1998

A Synchronization Algorithm and Implementation for High-Speed Block Codes Applications

Block codes have trellis structures and decoders amenable to high speed CMOS VLSI implementation. For a given CMOS technology, these structures enable operating speeds higher than those achievable using convolutional codes for only modest reductions in coding gain. As a result, block codes have tremendous potential for satellite trunk and other future high-speed communication applications. This paper describes a new approach for implementation of the synchronization function for block codes. The approach utilizes the output of the Viterbi decoder and therefore employs the strength of the decoder. Its operation requires no knowledge of the signal-to-noise ratio of the received signal, has a simple implementation, adds no overhead to the transmitted data, and has been shown to be effective in simulation for received SNR greater than 2 dB.

Lin, Shu↗
NASA NTRS2018

NOS3: NASA Operational Simulator for Small Satellites

The NASA Operational Simulator for Small Satellites (NOS3) is a suite of open-source software tools to aid in areas such as software development, integration & test (I&T), mission operations/training, verification and validation (V&V), and software systems check-out. NOS3 provides a software development environment, a multi-target build system, operational interface/ground software, dynamics and environment simulations, and software-based hardware models. NOS3 has just recently been open-sourced by NASA and is available for immediate use. It enables the development of flight software (FSW) early in the project life cycle when hardware availability is limited. Small satellite development suffers from extensive lead times on many of the commercial-off-the-shelf (COTS) components as well as limited funding for engineering test units (ETUs). To alleviate the need to provide a hardware test-bed for each developer/tester, NOS3 hardware models are based upon characteristic data or manufacturer's data sheets for each individual component. The NOS3 hardware models' fidelity is such that FSW executes unaware that physical hardware is not present. This allows FSW binaries to be compiled for both the simulation environment and the flight computer without changing the FSW source code. For hardware models that provide data which is dependent upon the environment and spacecraft dynamics, such as a GPS receiver or magnetometer, an open-source tool from NASA GSFC (42 Spacecraft Simulator) is used to provide the necessary data. The underlying infrastructure used to transfer messages between FSW and the hardware models can also be used to monitor, intercept, and inject messages, which has proven to be beneficial for V&V of larger missions such as James Webb Space Telescope (JWST). As hardware is selected and becomes available, drivers can be added to the NOS3 environment to enable hardware-in-the-loop (HWIL) testing. When strict time synchronization is not vital, any number of combinations of hardware components and software-based models can be tested. NOS3 was actively used for FSW development and component testing of the Simulation-to-Flight 1 (STF-1) CubeSat and the Lunar IceCube CubeSat. As NOS3 matures, hardware models have been added for common small satellite components such as GPS receivers, electrical power systems and batteries, and antenna systems.

Suder, Mark↗
NASA NTRS2012

Telescope with a wide field of view internal optical scanner

A telescope with internal scanner utilizing either a single optical wedge scanner or a dual optical wedge scanner and a controller arranged to control a synchronous rotation of the first and/or second optical wedges, the wedges constructed and arranged to scan light redirected by topological surfaces and/or volumetric scatterers. The telescope with internal scanner further incorporates a first converging optical element that receives the redirected light and transmits the redirected light to the scanner, and a second converging optical element within the light path between the first optical element and the scanner arranged to reduce an area of impact on the scanner of the beam collected by the first optical element.

Degnan, III, John James↗