Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “numerical optimal control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Optimal Design of Passive Flow Control for a Boundary-Layer-Ingesting Offset Inlet Using Design-of-Experiments

This research will investigate the use of Design-of-Experiments (DOE) in the development of an optimal passive flow control vane design for a boundary-layer-ingesting (BLI) offset inlet in transonic flow. This inlet flow control is designed to minimize the engine fan-face distortion levels and first five Fourier harmonic half amplitudes while maximizing the inlet pressure recovery. Numerical simulations of the BLI inlet are computed using the Reynolds-averaged Navier-Stokes (RANS) flow solver, OVERFLOW, developed at NASA. These simulations are used to generate the numerical experiments for the DOE response surface model. In this investigation, two DOE optimizations were performed using a D-Optimal Response Surface model. The first DOE optimization was performed using four design factors which were vane height and angles-of-attack for two groups of vanes. One group of vanes was placed at the bottom of the inlet and a second group symmetrically on the sides. The DOE design was performed for a BLI inlet with a free-stream Mach number of 0.85 and a Reynolds number of 2 million, based on the length of the fan-face diameter, matching an experimental wind tunnel BLI inlet test. The first DOE optimization required a fifth order model having 173 numerical simulation experiments and was able to reduce the DC60 baseline distortion from 64% down to 4.4%, while holding the pressure recovery constant. A second DOE optimization was performed holding the vanes heights at a constant value from the first DOE optimization with the two vane angles-of-attack as design factors. This DOE only required a second order model fit with 15 numerical simulation experiments and reduced DC60 to 3.5% with small decreases in the fourth and fifth harmonic amplitudes. The second optimal vane design was tested at the NASA Langley 0.3- Meter Transonic Cryogenic Tunnel in a BLI inlet experiment. The experimental results showed a 80% reduction of DPCP(sub avg), the circumferential distortion level at the engine fan-face.

Allan, Brian G.↗
NASA NTRS2011

Inlet Flow Control and Prediction Technologies for Embedded Propulsion Systems

Fail-safe, hybrid, flow control (HFC) is a promising technology for meeting high-speed cruise efficiency, low-noise signature, and reduced fuel-burn goals for future, Hybrid-Wing-Body (HWB) aircraft with embedded engines. This report details the development of HFC technology that enables improved inlet performance in HWB vehicles with highly integrated inlets and embedded engines without adversely affecting vehicle performance. In addition, new test techniques for evaluating Boundary-Layer-Ingesting (BLI)-inlet flow-control technologies developed and demonstrated through this program are documented, including the ability to generate a BLI-like inlet-entrance flow in a direct-connect, wind-tunnel facility, as well as, the use of D-optimal, statistically designed experiments to optimize test efficiency and enable interpretation of results. Validated improvements in numerical analysis tools and methods accomplished through this program are also documented, including Reynolds-Averaged Navier-Stokes CFD simulations of steady-state flow physics for baseline, BLI-inlet diffuser flow, as well as, that created by flow-control devices. Finally, numerical methods were employed in a ground-breaking attempt to directly simulate dynamic distortion. The advances in inlet technologies and prediction tools will help to meet and exceed "N+2" project goals for future HWB aircraft.

McMillan, Michelle L.↗
NASA NTRS1990

Advances and trends in computational structures technology

The major goals of computational structures technology (CST) are outlined, and recent advances in CST are examined. These include computational material modeling, stochastic-based modeling, computational methods for articulated structural dynamics, strategies and numerical algorithms for new computing systems, multidisciplinary analysis and optimization. The role of CST in the future development of structures technology and the multidisciplinary design of future flight vehicles is addressed, and the future directions of CST research in the prediction of failures of structural components, the solution of large-scale structural problems, and quality assessment and control of numerical simulations are discussed.

Noor, A. K.↗
NASA NTRS1985

Effect of maximum lift to drag ratio on optimal aeroassisted plane change

The influence of the maximum lift-to-drag ratio on the turning performance of an Orbital Transfer Vehicle is analyzed. Chapman's variables are used to formulate the equations of motion which are valid for both atmospheric flight and flight in a vacuum in a Newtonian gravitational field. Of the six adjoint variables involved in the variational formulation, four exact integrals and two approximate relations are obtained. This leads to an approximate but explicit control law for the lift and bank control. The control law is tested numerically for a whole range of entry speeds, from parabolic entry to near-circular entry with several values of maximum lift-to-drag ratio. The extensive numerical results, which are very accurate as compared to the exact optimal values, show that the maximum plane change for any speed ratio V(entry)/V(final) is simply proportional to the maximum lift-to-drag ratio, and depends solely on this parameter.

Johannesen, J. R.↗
NASA NTRS1982

Difference equation state approximations for nonlinear hereditary control problems

Discrete approximation schemes for the solution of nonlinear hereditary control problems are constructed. The methods involve approximation by a sequence of optimal control problems in which the original infinite dimensional state equation has been approximated by a finite dimensional discrete difference equation. Convergence of the state approximations is argued using linear semigroup theory and is then used to demonstrate that solutions to the approximating optimal control problems in some sense approximate solutions to the original control problem. Two schemes, one based upon piecewise constant approximation, and the other involving spline functions are discussed. Numerical results are presented, analyzed and used to compare the schemes to other available approximation methods for the solution of hereditary control problems.

Rosen, I. G.↗
NASA NTRS1983

Vibration control of large linear quadratic symmetric systems

Some unique properties on a class of the second order lambda matrices were found and applied to determine a damping matrix of the decoupled subsystem in such a way that the damped system would have preassigned eigenvalues without disturbing the stiffness matrix. The resulting system was realized as a time invariant velocity only feedback control system with desired poles. Another approach using optimal control theory was also applied to the decoupled system in such a way that the mode spillover problem could be eliminated. The procedures were tested successfully by numerical examples.

Jeon, G. J.↗
NASA NTRS1984

Difference equation state approximations for nonlinear hereditary control problems

Discrete approximation schemes for the solution of nonlinear hereditary control problems are constructed. The methods involve approximation by a sequence of optimal control problems in which the original infinite dimensional state equation has been approximated by a finite dimensional discrete difference equation. Convergence of the state approximations is argued using linear semigroup theory and is then used to demonstrate that solutions to the approximating optimal control problems in some sense approximate solutions to the original control problem. Two schemes, one based upon piecewise constant approximation, and the other involving spline functions are discussed. Numerical results are presented, analyzed and used to compare the schemes to other available approximation methods for the solution of hereditary control problems. Previously announced in STAR as N83-33589

Rosen, I. G.↗
NASA NTRS1987

Optimal placement of excitations and sensors for verification of large dynamical systems

The computationally difficult problem of the optimal placement of excitations and sensors to maximize the observed measurements is studied within the framework of combinatorial optimization, and is solved numerically using a variation of the simulated annealing heuristic algorithm. Results of numerical experiments including a square plate and a 960 degrees-of-freedom Control of Flexible Structure (COFS) truss structure, are presented. Though the algorithm produces suboptimal solutions, its generality and simplicity allow the treatment of complex dynamical systems which would otherwise be difficult to handle.

Salama, M.↗
NASA NTRS1993

Vibration control by limiting the maximum axial forces in space trusses

Proposed here is a method of vibration control based on limiting the maximum axial forces in the active members of an adaptive truss. The actuators simulate elastic rigid-plastic behavior and consume the vibrational energy as work. The method is applicable to both statically determinate as well as indeterminate truss structures. However, for energy efficient control of statistically indeterminate trusses extra actuators may be provided on the redundant bars. An energy formulation relating the various control parameters is derived to get an estimate of the control time. Since the simulation of elastic rigid-plastic behavior requires a piecewise linear control law, a general analytical solution is not possible. Numerical simulation by step-by-step integration is performed to simulate the control of an example truss structure. The problems of application to statically indeterminate trusses and optimal actuator placement are identified for future work.

Chawla, Vikas↗
NASA NTRS2005

Maintaining Situation Awareness with Autonomous Airborne Observation Platforms

Unmanned Aerial Vehicles (UAVs) offer tremendous potential as intelligence, surveillance and reconnaissance (ISR) platforms for early detection of security threats and for acquisition and maintenance of situation awareness in crisis conditions. However, using their capabilities effectively requires addressing a range of practical and theoretical problems. The paper will describe progress by the "Autonomous Rotorcraft Project," a collaborative effort between NASA and the U.S. Army to develop a practical, flexible capability for UAV-based ISR. Important facets of the project include optimization methods for allocating scarce aircraft resources to observe numerous, distinct sites of interest; intelligent flight automation software than integrates high-level plan generation capabilities with executive control, failure response and flight control functions; a system architecture supporting reconfiguration of onboard sensors to address different kinds of threats; and an advanced prototype vehicle designed to allow large-scale production at low cost. The paper will also address human interaction issues including an empirical method for determining how to allocate roles and responsibilities between flight automation and human operations.

Freed, Michael↗
NASA NTRS2022

A NASA-Air Force Precipitation Analysis for Near-Real-Time Operations

This article describes a new precipitation analysis algorithm developed by NASA for time-sensitive operations at the United States Air Force. Implemented as part of the Land Information System—a land modeling and data assimilation software framework—this NASA–Air Force Precipitation Analysis (NAFPA) combines numerical weather prediction model outputs with rain gauge measurements and satellite estimates to produce global, gridded 3-h accumulated precipitation fields at approximately 10-km resolution. Input observations are subjected to quality control checks before being used by the Bratseth analysis algorithm that converges to optimal interpolation. NAFPA assimilates up to 3.5 million observations without artificial data thinning or selection. To evaluate this new approach, a multiyear reanalysis is generated and intercompared with eight alternative precipitation products across the contiguous United States, Africa, and the monsoon region of eastern Asia. NAFPA yields superior accuracy and correlation over low-latency (up to 14 h) alternatives (numerical weather prediction and satellite retrievals), and often outperforms high-latency (up to 3.5 months) products, although the details for the latter vary by region and product. The development of NAFPA offers a high-quality, near-real-time product for use in meteorological, land surface, and hydrological research and applications.

Africa↗
NASA NTRS1988

Infinite-dimensional approach to system identification of Space Control Laboratory Experiment (SCOLE)

The identification of a unique set of system parameters in large space structures poses a significant new problem in control technology. Presented is an infinite-dimensional identification scheme to determine system parameters in large flexible structures in space. The method retains the distributed nature of the structure throughout the development of the algorithm and a finite-element approximation is used only to implement the algorithm. This approach eliminates many problems associated with model truncation used in other methods of identification. The identification is formulated in Hilbert space and an optimal control technique is used to minimize weighted least squares of error between the actual and the model data. A variational approach is used to solve the problem. A costate equation, gradients of parameter variations and conditions for optimal estimates are obtained. Computer simulation studies are conducted using a shuttle-attached antenna configuration, more popularly known as the Space Control Laboratory Experiment (SCOLE) as an example. Numerical results show a close match between the estimated and true values of the parameters.

Hossain, S. A.↗
NASA NTRS1988

Transformation techniques for minimax optimal control problems and their application to optimal flight trajectories in a windshear - Optimal abort landing trajectories

The optimal-control problem of abort-landing trajectories in the presence of low-altitude wind shear is investigated analytically. The vertical-plane Newtonian motion of a point-mass aircraft in a steady wind field is modeled, and a sequential gradient-restoration algorithm is applied. Numerical results showing the effects of wind-shear intensity, initial altitude, and power-setting rate are presented in extensive graphs and discussed in detail. Optimal trajectories for strong or severe wind shears are found to begin with a descent, followed by level flight and then an ascent after leaving the shear region.

Miele, A.↗
NASA NTRS1999

Integrated Aeroservoelastic Optimization: Status and Direction

The interactions of lightweight flexible airframe structures, steady and unsteady aerodynamics, and wide-bandwidth active controls on modern airplanes lead to considerable multidisciplinary design challenges. More than 25 years of mathematical and numerical methods' development, numerous basic research studies, simulations and wind-tunnel tests of simple models, wind-tunnel tests of complex models of real airplanes, as well as flight tests of actively controlled airplanes, have all contributed to the accumulation of a substantial body of knowledge in the area of aeroservoelasticity. A number of analysis codes, with the capabilities to model real airplane systems under the assumptions of linearity, have been developed. Many tests have been conducted, and results were correlated with analytical predictions. A selective sample of references covering aeroservoelastic testing programs from the 1960s to the early 1980s, as well as more recent wind-tunnel test programs of real or realistic configurations, are included in the References section of this paper. An examination of references 20-29 will reveal that in the course of development (or later modification), of almost every modern airplane with a high authority active control system, there arose a need to face aeroservoelastic problems and aeroservoelastic design challenges.

Livne, Eli↗
NASA NTRS1983

Optimal symmetric flight with an intermediate vehicle model

The present investigation is concerned with an examination of optimal symmetry flight on the basis of the intermediate vehicle model. The analysis is partly based upon an exploration of Euler solutions for the path-angle-as-control model carried out by Kelley (1958). The current analysis takes into account higher-order optimality conditions and 'chattering-control' phenomena. Attention is given to details regarding the intermediate vehicle model, the Legendre-Clebsch necessary condition, the conjugate-point test, and the numerical solution of the time-range problem. It is found that the flight path angle takes on the role of control variable in the model. From physical considerations, it can be seen that when a positive margin of thrust over drag exists, the maximum-range climb trajectory without time or fuel constraints has no proper maximum nor an upper bound.

Kelley, H. J.↗
NASA NTRS1983

Optimal symmetric flight with an intermediate vehicle model

The present investigation is concerned with an examination of optimal symmetry flight on the basis of the intermediate vehicle model. The analysis is partly based upon an exploration of Euler solutions for the path-angle-as-control model carried out by Kelley (1958). The current analysis takes into account higher-order optimality conditions and "chattering-control' phenomena. Attention is given to details regarding the intermediate vehicle model, the Legendre-Clebsch necessary condition, the conjugate-point test, and the numerical solution of the time-range problem. It is found that the flight path angle takes on the role of control variable in the model. From physical considerations, it can be seen that when a positive margin of thrust over drag exists, the maximum-range climb trajectory without time or fuel constraints has no proper maximum nor an upper bound.

Menon, P. K. A.↗
NASA NTRS1989

Application of precomputed control laws in a reconfigurable aircraft flight control system

A self-repairing flight control system concept in which the control law is reconfigured after actuator and/or control surface damage to preserve stability and pilot command tracking is described. A key feature of the controller is reconfigurable multivariable feedback. The feedback gains are designed off-line and scheduled as a function of the aircraft control impairment status so that reconfiguration is performed simply by updating the gain schedule after detection of an impairment. A novel aspect of the gain schedule design procedure is that the schedule is calculated using a linear quadratic optimization-based simultaneous stabilization algorithm in which the scheduled gain is constrained to stabilize a collection of plant models representing the aircraft in various control failure modes. A description and numerical evaluation of a controller design for a model of a statically unstable high-performance aircraft are given.

Moerder, Daniel D.↗