SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
ZnO–Ag x Au 1−x oxide–nanoalloy vertically aligned nanocomposite thin films have been grown via pulsed laser deposition and the film morphology and optical properties were tuned through oxygen partial pressure.
Nb 3 Sn is considered as a potential candidate for superconducting radiofrequency cavities for particle acceleration due to its higher transition temperature of 18.3 K and higher superheating field of 400 mT. Nb 3 Sn films can be grown inside the surface of a Nb cavity by sequentially sputtering multiple layers of Nb and Sn thin films followed by annealing at 950 °C for 3 h. We report on the properties of Nb 3 Sn films grown on Nb substrates by magnetron sputtering. The films’ crystal structure, surface morphology, and composition were characterized by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The films had a polycrystalline Nb 3 Sn structure with a fine-grain surface and an atomic Sn composition of ~23%. The RF surface resistance of the films was measured for different temperatures at 7.4 GHz to understand the feasibility of this method for the SRF application. The RF surface resistance of the films was 5 mΩ at 12 K, which is about 2 orders of magnitude higher than 60 μΩ previously measured in Nb 3 Sn films grown by Sn vapor diffusion. Finally, the sputtered film had a superconducting transition at 17.2 K, which is also lower than 17.9 K observed in Nb 3 Sn film prepared by vapor diffusion.
Abstract This work presents a pseudo-two-dimensional proton exchange membrane fuel cell (PEMFC) model incorporating Nafion ionomer structure–property relationships in the cathode catalyst layer (CL) to capture and explain losses at low Pt loading. Structural data from neutron reflectometry and thin film Nafion conductivity measurements predict variations in the oxygen diffusion coefficient and ionic conductivity with changing CL ionomer thickness and Pt loading. By including these structure–property relationships, predicted polarization curves agree closely with previously published experimental data from cells with Pt loadings between 0.025 and 0.2 mg/cm2. Results demonstrate that structure–property relationships based on physically measurable ionomer and CL properties provide a feasible interpretation of PEMFC CL phenomena for a range of Pt loadings and help explain previously unaccounted-for losses at low Pt. Results also show that simulations must account for surface species coverage variations in order to properly capture the kinetic losses. Finally, results suggest that an increase in ionomer thickness surrounding the C/Pt surfaces may lead to improved cell performance due to improved ionic conductivity.
Explore the source record for details and available documents.
Due to the growing number of people infected with the new coronavirus globally, which weakens immunity, there has been an increase in bacterial infections. Hence, knowledge about simple and low-cost synthesis methods of materials with good structural and antimicrobial properties is of great importance. A material obtained through the combination of a nanoscale hydroxyapatite material (with good biocompatibility) and titanium dioxide (with good degradation properties of organic molecules) can absorb and decompose bacteria. In this investigation, three different synthesis routes used to prepare hydroxyapatite/titanium dioxide nanomaterials are examined. The morphology and semiquantitative chemical composition are characterized by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX). The obtained materials’ phase and structural characterization are determined using the X-ray powder diffraction method (XRD). The crystallite sizes of the obtained materials are in the range of 8 nm to 15 nm. Based on XRD peak positions, the hexagonal hydroxyapatite phases are formed in all samples along with TiO 2 anatase and rutile phases. According to SEM and TEM analyses, the morphology of the prepared samples differs depending on the synthesis route. The EDX analysis confirmed the presence of Ti, Ca, P, and O in the obtained materials. The IR spectroscopy verified the vibration bands characteristic for HAp and titanium. The investigated materials show excellent antimicrobial and photocatalytic properties.
Tin-lead-antimony (50Sn–47Pb–3Sb wt.%) soldered assemblies were mechanically tested approximately 30 years after initial production and found to have solder joints of reduced strength. The microstructure of this solder alloy exhibits a ternary eutectic structure with Sn-rich, Pb-rich, and SnSb phases. Accelerated aging was performed to evaluate solder microstructural coarsening and associated strength of laboratory solder joints to correlate these properties to the “naturally aged” solder joints. Isothermal aging was conducted at room temperature, 55, 70, 100, and 135 °C and aging times that ranged from 0.1 to 365 days. The coarsening kinetics of the Pb-rich phase were determined through optical microscopy and image analysis methods established in previous studies on binary Sn–Pb solder. A kinetic equation was developed with time exponent n of 0.43 and activation energy of 24000 J/mol, suggesting grain boundary diffusion or other fast diffusion pathways controlling the microstructural evolution. Compression testing and Vickers microhardness showed significant strength loss within the first 20–30 days after soldering; then, the microstructure and mechanical properties changed more slowly over long periods of time. Further, by combining accelerated aging data and the microstructure-based kinetics, strength predictions were made that match well with the properties of the actual soldered assemblies naturally aged for 30 years. However, aging at the highest temperature of 135 °C produced anomalous behavior suggesting that extraneous aging mechanisms are active. Therefore, data obtained at this temperature or higher should not be used. Overall, the combined microstructural and mechanical property methods used in this study confirmed that the observed reduction in strength of ~ 30-year-old solder joints can be accounted for by the microstructural coarsening that takes place during long-term solid-state aging.
Auburn University (AU) teamed with the University of Missouri Research Reactor (MURR) and Kansas State University (KSU) to determine how to best use laser-powder bed fusion (L-PBF) additive manufacturing (AM) methods for generating radiation resistant nickel-based superalloys, Inconel alloy 625 and 718, for special purpose reactor (SPR) or very small modular reactor (vSMR) heat-exchangers (HeXs). Compact, conformal, and durable HeXs that are tolerant of extreme environments are needed for supporting the technical maturity of next-generation, portable compact reactors. AM is an enabler for realizing this new wave of HeXs – providing a means to make customizable hot and cold stream architectures with novel flow path geometries (e.g., tortuous channels with non-uniform, asymmetric cross-sections) and reduced layer-to-layer contact resistance (i.e., no separate bonding procedure required). AM further enables a more time/cost efficient means for fabricating SPRs by reducing the number of suppliers required for HeX assembly and allowing for on-site HeX fabrication. The project aim has been to better understand how neutron irradiation affects the microstructure and properties of additively manufactured nickel-based superalloys, to accelerate their safe, reliable use in the modular reactor industry. The major objective was to qualify/quantify the microstructure and microhardness of nickel-based superalloys (including Inconel 718 and 625) additively manufactured via the L-PBF process in the neutron-dosed (irradiated) and non-irradiated states over a course of 3 years. Effects of build orientation during L-PBF and post-AM heat treatments on neutron resistance, microstructure and mechanical properties were also investigated. Neutron damage mechanisms via hardening were characterized. This project combined subject-matter experts in AM, mechanical/microstructure metallic part characterization, and neutron irradiation, as well as unique assets and capabilities at AU and MURR at MU, to ensure project results translated to effectively addressing known gaps in nuclear science and engineering. Parts were fabricated using L-PBF systems readily available at AU. Specimens were then irradiated using MURR facilities; a manipulator equipped hot cell was also used to measure material hardness after dosing. MURR, a 10 MW, light-water nuclear reactor, is the largest, highest powered, highest-flux university owned research reactor in the U.S. The major findings in this project provide evidence that AM can serve as an alternative way to build structural components for future advanced small modular reactors using advanced materials like Inconel 625 (IN625) or Inconel 718 (IN718). After full spectrum neutron irradiation, vertically as-built AM IN625 samples were observed to display better resistance towards radiation-induced-hardening defects relative to traditionally machined metals. A Vickers microhardness tester, using settings of 1 kgf and dwell time of 15 seconds per indentation, was used to measure hardness in this study. The as-built, vertically printed samples experienced 1.2% of radiation hardening vs. 5.25% radiation hardening observed in wrought IN625. Another set of IN625 and IN718 samples were exposed to fast neutron irradiation. It was observed that IN718 showed more resistance towards radiation hardening compared to IN625 samples indicating IN718 had a better performance. Results showed that the IN718 samples experienced less change (-2.5 to 3.24 %) in microhardness. On the other hand, IN625 samples underwent more (0.9 to 7.21%) change in microhardness after fast neutron irradiation. AM IN625 samples were irradiated using an ion (proton) beam in cyclotron. The mechanical properties of AM samples post irradiation were compared with wrought samples. The irradiated region on the samples were tested using nano-hardness indention. It was observed that the beam current and time used in this study generated an annealing effect and thus reduced the hardness of the samples. The sum of the project results provide precious insight into how one may minimize radiation hardening in AM materials while maintaining material property constraints. Results should assist engineers in selecting an appropriate heat treatment for AM nickel-based superalloys for increased radiation resistance. Results should increase confidence levels for adopting AM for building nuclear reactor components which perform the same or better than conventionally manufactured components. Fast neutron irradiation testing provided an accelerated means of obtaining radiation effects without making materials radioactive and difficult to handle.
The Advanced Materials and Manufacturing Technologies (AMMT) program within the Department of Energy (DOE) Office of Nuclear Energy has developed its current recommendation for promoting the use of combined ion irradiation and neutron irradiation for the accelerated qualification of materials to be deployed in nuclear reactors. This plan is intended to provide a collaborative path forward that can be adopted by academia, national laboratories, and industry, and has been developed with input from the regulatory research arm of the U.S. Nuclear Regulatory Commission (NRC). To deploy new materials or materials manufactured with new technologies, such as additive manufacturing, materials must be evaluated for reactor-induced degradation from the combination of harsh temperatures, corrosive environments, and radiation fields. However, rapid deployment of materials necessitates accelerated testing methods rather than relying on years of neutron irradiation in a material test reactor. Ion irradiation has demonstrated success in reproducing material microstructure and select property evolution resulting from neutron irradiation with three to four orders of magnitude reduction in time and cost, making it an ideal candidate for accelerated irradiation testing. This presentation provides context governing both the scientific and regulatory aspects of the proposed goal. The discussion is aimed at a broad audience including researchers from industry, national laboratories, and academia. The recommended path forward is presented as a conceptual framework of specific steps. In brief, the strategy entails developing an integrated ion and neutron irradiation test plan for the material property of interest based on the fundamental tenet of the linkage of microstructure and properties in materials. Physics-based modeling interprets ion irradiation data and predicts neutron irradiation microstructure and properties with uncertainty bounds. The first round of testing is sufficient for an initial licensing application using a risk-informed approach, while a minimum required neutron irradiation test plan reduces cost and time requirements. A surveillance program with witness specimens in-reactor provides additional data over time to improve model predictions to higher damage levels and further reduce uncertainty bounds, which can be used for license extensions or longer lifetimes in new license applications.
This work focuses on systematic studies of Ce–Co based 1:5 permanent magnet alloys of CeCo 4.4-x Fe x Cu 0.6 and CeCo 3.9-x Fe x Cu 1.2 (x = 0, 0.3, 0.6, 0.9, 1.2, 1.8) by varying Co:Fe. The overarching aim of this manuscript is to elucidate the hard-magnetic properties through a better understanding of phase formation by the structural, microstructural, and magnetic properties in these materials. Improved mutual solubility of Fe in the 1:5 phase has been observed with an extended homogeneity range by Cu substitution. For both composition series, Fe contents of x ≤ 0.6 show a homogeneous microstructure with a single 1:5 phase and good magnetic properties. The composition region 0.6 < x ≤ 0.9 appears to be near the boundary of solubility and evolution of other phases. At x = 1.8, it is found that the homogeneous 1:5 phase and magnetic hardness deteriorated due to the evolution of secondary phases such as 2:17, 2:7, and Fe–Co. Furthermore, the addition of Fe improved both the magnetization and Curie temperature via increased effective exchange interactions, while an increase in Cu content enhanced coercivity.
Nuclear energy remains a critical component of a diversified and efficient energy portfolio, offering reliable, high-capacity, and low-carbon power. However, in the U.S., aging infrastructure and the slow qualification and deployment of advanced materials and manufacturing techniques hinder progress in next-generation reactor technologies. This study explores the application of laser powder bed fusion (LPBF) additive manufacturing for stainless steel 316H, with a focus on optimizing post-build heat treatments to enhance material properties for high-temperature nuclear applications. The research targets the optimization of stress-relief temperatures to alleviate postbuild residual stresses, ensuring improvements in the microstructural corelated properties. A series of microstructural and mechanical evaluations were performed on LPBF-printed SS-316H samples which were subjected to annealing at temperatures varying between 650 °C and 850 °C. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses revealed that increasing the heattreatment temperature accelerated dislocation recovery. Vickers microhardness measurements showed an initial reduction in values, followed by stabilization over extended durations at all the temperatures. While higher temperatures facilitated faster recovery, they also promoted carbide precipitation along grain and solidification cell boundaries, narrowing the safe processing window. In contrast, heat treatment at 650°C preserved the cellular substructure and enabled controlled carbide precipitation over time. In conclusion, these findings highlight the importance of time–temperature optimization and suggest that 650°C for up to 2 h provides the most favorable balance between recovery and carbide control for a stress-relief treatment.
Graphene oxide (GO) membranes intercalated with various organic moieties have shown excellent potential for a range of water processing applications. However, microstructure–functional property relationships in these structurally disordered membranes are not well understood. We demonstrate a practical methodology for developing such relationships for GO membranes intercalated with molecular species, with polycyclic aromatic toluidine blue O (TBO) as an example functional intercalant. We use solid-state UV–vis absorbance and fluorescence measurements to quantitatively track the arrangements of TBO in a series of TBO-loaded reduced GO (rGO) membranes. This study reveals the evolution of diverse arrangements including TBO monomers, lateral and stacked dimers, and other aggregates, as a function of overall TBO loading. These microstructures are then correlated to changes in overall properties such as interlayer d-spacings, permeate fluxes, and solute rejections. The characterization of these different intercalant microstructures explains non-intuitive flux and rejection trends, which can circumvent flux and solute rejection trade-offs.
Metal additive manufacturing (AM) offers a unique opportunity for production of advanced materials and complex geometries. However, variability in microstructure and properties challenges conventional approaches to design, process optimization, qualification, and materials selection. Modeling and simulation can improve understanding of AM processing and materials, but also poses major challenges for existing computational methods. Simultaneously, modern scientific computing hardware has become increasingly complex, most notably with the adoption of hybrid architectures such as Graphical Processing Units (GPUs). If appropriately utilized, emerging computational capabilities provide an opportunity to reveal new insight into AM processing and the resulting material structure and properties. In this review we describe the computational AM landscape, identify critical gaps, and highlight opportunities to impact the development and application of AM. First, the requirements and challenges of representative AM problem statements will be defined. Here, these problems range from scientific studies to industrial applications and are designed to capture the breadth of challenges facing the AM community. Next, the current state of AM modeling and simulation is evaluated, broken down by enabling hardware and software, process simulation, microstructure simulation, and property simulation. Each section describes the diversity of simulation approaches and associated trade-offs in physical fidelity and computational expense. Each area is then assessed based on their suitability and readiness for current and developing computational architectures. Lastly, the greatest opportunities for future research and application are highlighted, including gaps in modeling capabilities, opportunities for near-term application, and key scientific challenges.
Qualifying large-scale metal additive manufacturing (M-AM) technologies such as wire arc additive manufacturing (WAAM) can be challenging. This is especially significant in precipitation hardened martensitic stainless steels like SS 17-4PH, where thermal histories induce location-specific microstructural variability and property anisotropy. The Department of Defense (DOD) and the United States Army Combat Capabilities Development Command Ground Vehicle Systems Center (GVSC) Ground Vehicle Materials Engineering (GVME) aim to build robust and qualified large-scale M-AM workflows that could reduce the time and cost through quick and informed evaluation, testing, and development of feedstock, processes, and parts. The report presents the findings from the collaborative efforts between Oak Ridge National Laboratory (ORNL) and the U.S. Army GVSC GVME. The aim of this project was to develop a geometric feature-based qualification framework for WAAM of SS 17-4PH components. This report outlines selection methodology of representative build geometries, optimization of WAAM process parameters, in-situ monitoring, microstructure-property evaluation, thermal simulations, as well as data visualization techniques incorporated in this project. The results from this project demonstrate a clear understanding of thermal history dependent phase evolution and consequent location-specific property variations in WAAM of SS 17-4PH. These results in conjunction with the data-driven methodologies used in this project are expected to reduce qualification timelines, improve predictability, and accelerate the development of reliable feature-based qualification strategies for part production via large-scale M-AM technologies.
One-dimensional titanium dioxide (TiO 2 ) nanostructure arrays (nanoarrays) are important metal oxide nanomaterials that can be synthesized via facile solvothermal methods. The properties of the organic solvents can impose significant effects on the microstructures and properties of the final products. However, the discussions were limited to the homogeneously nucleated TiO 2 nanomaterials in free-standing powder form, while the solvent effects are less understood during the heterogeneous growth of TiO 2 nanoarrays on a substrate surface. In this work, six organic compounds, namely 2-butanone, n-decane, n-hexane, toluene, ethylene glycol and ethanol, were selected as the solvents for the solvothermal synthesis of TiO 2 nanoarrays on the cordierite monolithic substrates. Special attentions are paid to the morphology, crystallinity, specific surface area, and porosity of the samples. The heterogeneous growth of TiO 2 nanoarrays on substrate surfaces is found to favor the solvents with moderate dielectric constants, which can be partially dissolved in the aqueous solution and modulate the reaction rate during the solvothermal synthesis. Organic solvents with low dielectric constants may result in a complete separation between the precursors and aqueous solution, and therefore slow down the overall reaction, causing the insufficient growth of the nanoarrays. The TiO 2 nanoarrays are obtained with optimum morphology from the combination of 2-butanone and titanium (IV) butoxide as solvent and precusor, respectively, with a high specific surface area up to 56 m 2 /g including cordierite substrate given a micron thickness. When loaded with Pt catalyst, the TiO 2 nanoarray-based monolithic catalysts show excellent low-temperature catalytic activity and hydrothermal stability for the CO and hydrocarbon oxidation under the simulated exhausted conditions. This article shall shed light on a better understanding of the growth mechanism and rational design of TiO 2 nanoarrays for high-performance catalytic converters.
Nickel-based superalloys are in great demand for harsh-service conditions involving high temperatures and oxidative environments. Haynes 282 stands out due to its excellent high-temperature properties and easy fabricability. However, the upper operation temperature of Haynes 282 is limited due to its relatively low liquidus temperature. Equipped with high-fidelity density-functional theory calculations and high-throughput experimentation methodology, we explored new compositional spaces that exhibit higher liquidus temperature and higher strength. While maintaining the manufacturability, the newly designed alloy shows improved strength and ductility at room temperature and better oxidation resistance up to 800°C. Here, the new compositions showcase a minor change in the refractory and metalloid content can significantly impact the mechanical and oxidation performance of superalloys.
Thermal aging of ferrite in duplex stainless steels leads to a complex microstructural evolution that can give way to large deleterious changes in mechanical properties. The microstructural evolution mechanisms that happen concurrently are strongly linked to minor changes in composition. By characterizing duplex stainless steels with various compositions over a range of aging conditions, it was revealed that adding a modest amount of Mo to cast austenitic stainless steel (such as changing from grade CF3 to grade CF3M) not only increases the kinetics of spinodal decomposition and Ni-Si-Mn-rich G-phase precipitation, but it also forms a separate Mo-rich phase. At shorter equivalent aging times, Mo segregates from Fe and towards Cr accelerating spinodal decomposition. At longer aging times, Mo enriches in the Ni-Si-Mn clusters before phase separating into an adjoined Mo-rich cluster. We found that these phase changes and precipitation events result in a rather steep drop in fracture and impact toughness. These results will inform the design of similar alloys for use at high temperatures.
Creep-rupture properties and oxidation behavior of a series of alumina-forming austenitic (AFA) alloys with variations of Cr contents, based on Fe-(13.5-18)Cr-25Ni-4Al-1.5Nb-0.1C in weight percent, have been evaluated at 850–900 °C. The study investigates material responses in the properties and microstructure through compositional modifications in AFA alloys, targeting performance optimization of alloys under high-temperature, corrosive industrial environments. The creep-rupture life of the alloys at 850 °C and 30MPa monotonically decreased with increasing Cr content, which was correlated with changes in secondary phase volume fractions, such as the reduction in B2-NiAl + Laves-Fe2Nb and increase in Sigma-FeCr with Cr content. The oxidation test at 900 °C in a water-vapor containing environment revealed a range of Cr content from 13.9 to 15.7 wt.%, enabling the formation of stable, protective external alumina scale as well as preventing internal oxidation/nitridation for up to total 7000 h exposure. On the other hand, the alloys with >16.7 wt.% Cr formed Sigma precipitates, which caused a reduction in not only Cr but also Al in the austenite matrix, resulting in less oxidation resistance than other alloys. The findings will guide the further optimization of material performance in the AFA alloy series.
3D printing of unique structures with tunable properties offers significant advantages in the fabrication of complex and customized electronic devices. Here, this study introduces a process-microstructure–property-guided manufacturing route to fabricate PVDF-2D MoS 2 piezoelectric nanocomposites with tunable piezoelectric properties without having a postprocess. We control PVDF’s microstructure through direct ink writing (DIW) 3D printing while tuning PVDF-MoS 2 interfacial strain by controlling rheology and 3D printing parameters, such as nozzle size and printing speed. Our approach demonstrates tunable piezoelectricity in PVDF-MoS 2 , achieving a 15-fold increase in the piezoelectric coefficient (d 33 ) at a printing-induced shear stress of 6685 Pa. This enhancement arises from the electrostatic interactions between PVDF and MoS 2 and the filler distribution and alignment caused by the in situ shear stress in 3D printing, as confirmed by XPS and Raman mapping analyses. Our findings advance the understanding of piezoelectric mechanisms in PVDF-based nanocomposites, laying the foundation for 3D printing of piezoelectric sensors in wearable device applications with enhanced performance and customization capabilities.