Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “jet flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Effect of nonuniform geometries on flow distributions and heat transfer characteristics for arrays of impinging jets

Two-dimensional arrays of circular jets impinging on a surface parallel to the jet orifice plate are considered. The jet flow, after impingement, is constrained to exit in a single direction along the channel formed by the jet orifice plate and the impingement surface. Experimental results for the effects of streamwise nonuniform array geometries on streamwise flow distributions and heat transfer characteristics are presented. A flow distribution model for nonuniform arrays is developed and validated by comparison with the measured flow distributions. The model is then employed to compare nonuniform array streamwise resolved heat transfer coefficient data with previously reported uniform array data and with a previously developed correlation based on the uniform array data. It was found that uniform array results can, in general, serve as a satisfactory basis from which to predict heat transfer coefficients at individual spanwise rows of nonuniform arrays. However, significant differences were observed in some cases over the first one or two rows downstream of the geometric transition line of the nonuniform array.

Florschuetz, L. W.↗
NASA NTRS1994

Mixing and Noise Benefit Versus Thrust Penalty in Supersonic Jets Using Impingement Tones

This paper reports the results of an experimental investigation on the effect of impingement tones generated by obstacles of various geometries on the spreading of a supersonic jet flow. A rectangular supersonic jet was produced using a convergent-divergent nozzle that was operated near its design point (with shocks minimized). The immersion of obstacles in the flow produced an intense impingement tone which then propagated upstream (as feedback) to the jet lip and excited the antisymmetric hydrodynamic mode in the jet, thus setting up a resonant self-sustaining loop. The violent flapping motion of the jet due to excitation of the antisymmetric mode, combined with the unsteady wakes of the obstacles, produced large changes in jet mixing. It was possible to control the frequency and amplitude of the impingement tone excitation by varying the nozzle-to-obstacle distance and the obstacle immersion. By proper shaping of the obstacles it was possible to reduce the thrust penalty significantly.

Raman, Ganesh↗
NASA NTRS1994

CFD Assessment of Orifice Aspect Ratio and Mass Flow Ratio on Jet Mixing in Rectangular Ducts

Isothermal CFD analysis was performed on axially opposed rows of jets mixing with cross flow in a rectangular duct. Laterally, the jets' centerlines were aligned with each other on the top and bottom walls. The focus of this study was to characterize the effects of orifice aspect ratio and jet-to-mainstream mass flow ratio on jet penetration and mixing. Orifice aspect ratios (L/W) of 4-to-1, 2-to-1, and 1-to-1, along with circular holes, were parametrically analyzed. Likewise, jet-to-mainstream mass flow ratios (MR) of 2.0, 0.5, and 0.25 were systematically investigated. The jet-to-mainstream momentum-flux ratio (J) was maintained at 36 for all cases, and the orifice spacing-to-duct height (S/H) was varied until optimum mixing was attained for each configuration. The numerical results showed that orifice aspect ratio (and likewise orifice blockage) had little effect on jet penetration and mixing. Based on mixing characteristics alone, the 4-to-1 slot was comparable to the circular orifice. The 4-to-1 slot has a smaller jet wake which may be advantageous for reducing emissions. However, the axial length of a 4-to-1 slot may be prohibitively long for practical application, especially for MR of 2.0. The jet-to-mainstream mass flow ratio had a more significant effect on jet penetration and mixing. For a 4-to-1 aspect ratio orifice, the design correlating parameter for optimum mixing (C = (S/H)(sq. root J)) varied from 2.25 for a mass flow ratio of 2.0 to 1.5 for a mass flow ratio of 0.25.

Bain, D. B.↗
NASA NTRS1994

Experimental Investigation of Jet-Induced Mixing of a Large Liquid Hydrogen Storage Tank

Experiments have been conducted to investigate the effect of fluid mixing on the depressurization of a large liquid hydrogen storage tank. The test tank is approximately ellipsoidal, having a volume of 4.89 m(exp 3) and an average wall heat flux of 4.2 W/m(exp 2) due to external heat input. A mixer unit was installed near the bottom of the tank to generate an upward directed axial jet flow normal to the liquid-vapor interface. Mixing tests were initiated after achieving thermally stratified conditions in the tank either by the introduction of hydrogen gas into the tank or by self-pressurization due to ambient heat leak through the tank wall. The subcooled liquid jet directed towards the liquid-vapor interface by the mixer induced vapor condensation and caused a reduction in tank pressure. Tests were conducted at two jet submergence depths for jet Reynolds numbers from 80,000 to 495,000 and Richardson numbers from 0.014 to 0.52. Results show that the rate of tank pressure change is controlled by the competing effects of subcooled jet flow and the free convection boundary layer flow due to external tank wall heating. It is shown that existing correlations for mixing time and vapor condensation rate based on small scale tanks may not be applicable to large scale liquid hydrogen systems.

Lin, C. S.↗
NASA NTRSDate not supplied

Wall Modeled Large Eddy Simulations for NASA’s Jet Noise Consensus Database of Single-Flow, Round, Convergent Jets

A campaign of wall-modeled large-eddy simulations (WMLES) using structured curvilinear overlapping grids has been performed with the Launch Ascent and Vehicle Aerodynamics(LAVA) computational fluid dynamics (CFD) software to predict jet noise for single-stream axisymmetric round jets. The simulations address the new Prediction Uncertainty Reduction(PUR) technical challenge within the context of NASA’s Commercial Supersonic Technology(CST) project. The goal of PUR is to quantify and reduce uncertainties from scale-resolving simulations to assess noise characteristics of next generation quiet supersonic commercial jets during takeoff and landing conditions where the noise from the exhaust jet dominates. The focus of this effort is to generate a simulation database for single-stream axisymmetric round nozzles at several conditions both for static (no ambient co-flow), which is the focus of this article, and in-flight (flight stream co-flow) conditions, which are beyond the current scope. Nine different flow conditions ranging in jet exit Mach number from 0.38 to 1.0 with nozzle temperature ratios (NTR) from 0.84 to 2.7 have been conducted. Details of the structured overset grids, numerical discretization and wall-model are provided. Near-field comparisons to PIV data show great agreement for both velocity and normal stresses, however a systematic TKE overshoot at the nozzle exit is seen in the lip line shear-layer. A permeable Ffowcs Williams Hawkings (FWH) surface, enclosing the jet, is used to predict far-field noise from the simulated flow-field. Comparison of CFD predictions to microphone array measurements demonstrate excellent agreement within the resolved frequency range. A systematic under-prediction of far-aft observer angles larger than 150 degrees has been observed across all simulations. We achieved a cost reduction of an order of magnitude for these WMLES compared to an earlier study of this configuration due to algorithmic and software improvements. The accuracy of the results and short turnaround time demonstrate that WMLES within the LAVA framework is a cost-effective approach for jet noise predictions that could soon be incorporated into the design cycle of jet noise reduction technologies.

CST↗
NASA NTRS1975

Acoustics of attached and partially attached flow for simplified OTW configurations with 5:1 slot nozzle

The acoustics of simple engine over-the-wing configurations, with complete and partially attached jet flow to the shielding surface were studied with scale models. The nozzle used consisted of a 5:1 slot nozzle operated at a nominal jet Mach number of 0.6, with the flow directed parallel to and at angles up to 10 deg toward the shielding surface. The flow field at the trailing edge of each nozzle/surface configuration was mapped. the results indicate that, with attached flow, the jet flow field is stretched in the flow direction resulting in locally higher velocities than those for partially attached flow or nozzle only flow. The stretching of the flow field increases the noise levels for the attached flow cases compared to those with only partially attached flow. With attached flow, the shielding benefits are substantially reduced compared with fully detached flow.

Vonglahn, U.↗
NASA NTRS1993

Numerical simulation of a complete STOVL aifcraft in ground effect

The aerodynamic environment encountered by powered-lift aircraft operating in ground effect is unique among flight vehicles. It is characterized by low forward speed with embedded regions of high subsonic or supersonic jet flows. During ground effect operations, complex recirculating flows generated by the jets produce large changes in the aerodynamic loads on the flight vehicle. Analytic prediction and small-scale experimental methods have produced mixed results in this flight regime, with the result that costly full-scale powered tests are required to evaluate the performance of candidate designs. The ability to accurately predict vehicle performance without resorting to full-scale tests will be critical to future powered-lift aircraft projects. This paper summarizes efforts to predict the flow field about a powered-lift aircraft, the YAV-8B Harrier, in low level jet-borne flight by solution of the Reynolds-averaged Navier-Stokes equations. Results are compared to infrared images of the NASA YAV-8B Harrier V/STOL Systems Research Aircraft (VSRA) under similar flight conditions.

Smith, Merritt H.↗
NASA NTRS2003

Digital Particle Image Velocimetry (DPIV) Used for Space-Time Correlations in Nozzle Flow

An optical measurement technique known as Digital Particle Image Velocimetry (DPIV) was used previously to characterize the first- and second-order statistical properties of both cold and hot jet flows from externally mixed nozzles in NASA Glenn Research Center's Nozzle Acoustic Test Rig. In this technique, an electronic camera records particles entrained in a flow as a laser light sheet is pulsed at two instances in time. Correlation processing of the recorded particle image pairs yields the two-component velocity field across the imaged plane of the flow. The information acquired using DPIV is being used to improve our understanding of the decay of turbulence in jet flows-a critical element for understanding the acoustic properties of the flow. Recently, two independent DPIV systems were installed in Glenn's Small Hot Jet Acoustic Rig, enabling multiplane correlations in time and space. The data were collected over a range of different Mach numbers and temperature ratios. DPIV system 1 was fixed to a large traverse rig, and DPIV system 2 was mounted on a small traverse system mounted on the large traverse frame. The light sheets from the two DPIV systems were aligned to lie in the same axial plane, with DPIV system 2 being independently traversed downstream along the flow direction. For each measurement condition, the DPIV systems were started at a fully overlapping orientation. A polarization separation technique was used to avoid cross-talk between the two systems. Then, the DPIV systems fields were shifted axially apart, in successively increasing steps. The downstream DPIV system 2 was triggered at a short time delay after the upstream DPIV system 1, where the time delay was proportional to the convective flow velocity in the shear layer of the jet flow and the axial separation of the two DPIV systems. The acquired data were processed to obtain the instantaneous velocity vector maps over a range of time delays and spatial separations. The velocity fields from the different DPIV systems were then cross-correlated to determine the degree of correlation remaining in the flow as the downstream convection distance was increased. The new data provide Lagrangian measurements of the convective turbulent structures in the shear layer of an exhaust nozzle. These measurements, obtained in both cold and hot flows, will be used to validate and correct models for space-time velocity correlations-long a missing key to predicting jet noise.

Wernet, Mark P.↗
NASA NTRS1996

Aeroacoustics of Turbulent High-Speed Jets

Aeroacoustic noise generation in a supersonic round jet is studied to understand in particular the effect of turbulence structure on the noise without numerically compromising the turbulence itself. This means that direct numerical simulations (DNS's) are needed. In order to use DNS at high enough Reynolds numbers to get sufficient turbulence structure we have decided to solve the temporal jet problem, using periodicity in the direction of the jet axis. Physically this means that turbulent structures in the jet are repeated in successive downstream cells instead of being gradually modified downstream into a jet plume. Therefore in order to answer some questions about the turbulence we will partially compromise the overall structure of the jet. The first section of chapter 1 describes some work on the linear stability of a supersonic round jet and the implications of this for the jet noise problem. In the second section we present preliminary work done using a TVD numerical scheme on a CM5. This work is only two-dimensional (plane) but shows very interesting results, including weak shock waves. However this is a nonviscous computation and the method resolves the shocks by adding extra numerical dissipation where the gradients are large. One wonders whether the extra dissipation would influence small turbulent structures like small intense vortices. The second chapter is an extensive discussion of preliminary numerical work using the spectral method to solve the compressible Navier-Stokes equations to study turbulent jet flows. The method uses Fourier expansions in the azimuthal and streamwise direction and a 1-D B-spline basis representation in the radial direction. The B-spline basis is locally supported and this ensures block diagonal matrix equations which are solved in O(N) steps. A very accurate highly resolved DNS of a turbulent jet flow is expected.

Rao, Ram Mohan↗
NASA NTRS2003

Performance Analysis of a Cost-Effective Electret Condenser Microphone Directional Array

Microphone directional array technology continues to be a critical part of the overall instrumentation suite for experimental aeroacoustics. Unfortunately, high sensor cost remains one of the limiting factors in the construction of very high-density arrays (i.e., arrays containing several hundred channels or more) which could be used to implement advanced beamforming algorithms. In an effort to reduce the implementation cost of such arrays, the authors have undertaken a systematic performance analysis of a prototype 35-microphone array populated with commercial electret condenser microphones. An ensemble of microphones coupling commercially available electret cartridges with passive signal conditioning circuitry was fabricated for use with the Langley Large Aperture Directional Array (LADA). A performance analysis consisting of three phases was then performed: (1) characterize the acoustic response of the microphones via laboratory testing and calibration, (2) evaluate the beamforming capability of the electret-based LADA using a series of independently controlled point sources in an anechoic environment, and (3) demonstrate the utility of an electret-based directional array in a real-world application, in this case a cold flow jet operating at high subsonic velocities. The results of the investigation revealed a microphone frequency response suitable for directional array use over a range of 250 Hz - 40 kHz, a successful beamforming evaluation using the electret-populated LADA to measure simple point sources at frequencies up to 20 kHz, and a successful demonstration using the array to measure noise generated by the cold flow jet. This paper presents an overview of the tests conducted along with sample data obtained from those tests.

Humphreys, William M., Jr.↗
NASA NTRS1979

Some observations of flow structure in multiple jet mixing

Results of hot wire measurements in an incompressible jet issuing from an array of rectangular lobes, equally spaced with their small dimensions in a line, both as a free jet, and as a confined jet, are presented. In the case of a multiple free jet, the flow field for downstream distance x greater than 60D (D = width of a lobe) resembles that of a jet exiting from a two-dimensional nozzle with its short dimension being the long dimension of the lobe. The field of turbulence is found to be nearly isotropic in the plane containing the small dimension of the lobes for x greater than 60D. In the case of a confined multiple jet, the flow field is observed to be nearly homogeneous and isotropic for x greater than 60D.

Krothapalli, A.↗
NASA NTRS1979

Temperature and species concentration measurements in a swirl-stabilized combustor

An experimental evaluation of a swirl-stabilized combustor is presented. The combustor is composed of two confined, concentric, swirling jets. The inner jet flow is lean premixed methane and air; the outer flow is air. Combustion is stabilized on a swirl-induced recirculation zone. Mean temperature and mean concentrations of major species are measured throughout the combustor, including the recirculation zone. Fine wire thermocouples are used to measure temperature. A gas chromatograph and a chemi-luminescence analyzer are employed to analyze samples extracted by a water-cooled gas-sampling probe. Results are presented in the form of isotherms and isopleths of species concentration in the combustor for two swirl conditions: co-swirl and counter-swirl. The effects of swirl on the combustion are discussed in light of flame quenching due to rapid dilution and cooling of the reacting inner jet flow by mixing with the outer flow. Evidence for probe induced perturbations of the combustion process is observed.

Oven, M. J.↗
NASA NTRS2021

Time Resolved Particle Image Velocimetry in Nozzle Flow

Temporally resolved particle image velocimetry (TR-PIV) is the newest and most exciting tool recently developed to support our continuing efforts to characterize and improve our understanding of the decay of turbulence in jet flows—a critical element for understanding the acoustic properties of the flow. A new TR-PIV system has been developed at the NASA Glenn Research Center which is capable of acquiring planar PIV image frame pairs at up to 25 kHz. The data reported here were collected at Mach numbers of 0.5 and 0.9 and at temperature ratios of 0.89 and 1.76. The field of view of the TR-PIV system covered six nozzle diameters along the lip line of the 50.8 mm diameter jet. The cold flow data at Mach 0.5 were compared with hotwire anemometry measurements in order to validate the new TR-PIV technique. The axial turbulence profiles measured across the shear layer using TR-PIV were thinner than those measured using hotwire anemometry and remained centred along the nozzle lip line. The collected TR-PIV data illustrate the differences in the single point statistical flow properties of cold and hot jet flows. The planar, time-resolved velocity records were then used to compute two-point space–time correlations of the flow at the Mach 0.9 flow condition. The TR-PIV results show that there are differences in the convective velocity and growth rate of the turbulent structures between cold and hot flows at the same Mach number.

Temporally Resolved Particle Image Velocimetry↗
NASA NTRS1968

Back flow from jet plumes in vacuum

Approximate analytical calculations to determine particle density at surrounding points forward of jet nozzle in vacuum due to exhausted gas in jet plume

Grier, N. T.↗
NASA NTRS1977

Numerical prediction of aeroacoustic jet-flap flows

Turbulent boundary layer flows departing an aerodynamic surface are experimentally verified to be strong sources of noise. Analysis of the source tensor of the Lighthill equation identifies important gradients of mean and fluctuating velocity components. Transition distributions of mean flow and select fluctuating velocity correlations, within the region immediately downstream of a sharp edged flap terminus are established by finite element solution of a parabolized form of the time-averaged steady flow Navier-Stokes equations closed with a turbulence kinetic energy model. Numerical solutions are presented which quantize the localized large mean flow accelerations and resultant peaks in the distribution of turbulence kinetic energy in the near wake region. Results are verified by comparison to experiment.

Baker, A. J.↗
NASA NTRS1978

Investigation of the jet-wake flow of a highly loaded centrifugal compressor impeller

Investigations, aimed at developing a better understanding of the complex flow field in high performance centrifugal compressors were performed. Newly developed measuring techniques for unsteady static and total pressures as well as flow directions, and a digital data analysis system for fluctuating signals were thoroughly tested. The loss-affected mixing process of the distorted impeller discharge flow was investigated in detail, in the absolute and relative system, at impeller tip speeds up to 380 m/s. A theoretical analysis proved good coincidence of the test results with the DEAN-SENOO theory, which was extended to compressible flows.

Eckardt, D.↗
NASA NTRS1986

Numerical simulation of backward step and jet exhaust flows

Preparatory to a continuing study of efficient, high resolution flow structure capture on patched mesh systems, turbulent flowfield solutions for a tactical missile base flow problem are computed on two first level composite grids of differing topologies. One mesh is of the wraparound character and the other is a step mesh on the Cartesian topology. A simplified Baldwin-Lomax algebraic eddy viscosity model is applied in the wake region. Results for the two meshes are compared with each other and with other computations reported in the literature. The totality of results suggest both mesh topology and resolution are important factors in the accuracy of predictive results as well as turbulence modeling. Related to interests in high altitude laminar flows bluff bodies such as the AOTV, the paper also presents results from a solution from laminar flow over a backward facing step and makes comparison with the available classical experiment of Chapman, et al.

Lombard, C. K.↗