Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Temperature dependent interfacial microstructure in HIP-bonded Al6061/Zr joints

Pressing (HIP) at 450 °C and 560 °C under 103 MPa for 90 minutes to evaluate interfacial diffusion and microstructural evolution. Sound metallurgical bonding was achieved at both temperatures, with Zr serving as an effective diffusion barrier. Microstructural analysis revealed the the formation of a (Al,Si)3Zr intermetallic layer at the Al/Zr interface, whose thickness increased from ~100 nm at 450 °C to ~2100 nm at 560 °C, consistent with temperature-driven diffusion kinetics. The thin and continuous reaction layer observed at 450 °C indicates controlled interdiffusion and minimal reaction zone growth, favorable for maintaining interface stability and ductility. At 560 °C, enhanced atomic mobility led to pronounced intermetallic development, confirming diffusion-controlled growth behavior. These results provide valuable insights for optimizing Al/Zr interface design and diffusion barrier performance in advanced structural and energy systems.

Al/Zr interface↗
NASA NTRSDate not supplied

Modified Epoxy Matrix Resins for Reduced Dependence on Redundant Fasteners in Secondary-Bonded Composite Structures

In structural bonds, the interface between adherend and adhesive is nearly two-dimensional making it susceptible to minute quantities of contamination that can lead to weak bonds. No methods currently exist to measure the strength of an adhesive bond nondestructively. For these reasons, regulating organizations such as the Federal Aviation Administration (FAA) often require redundant load paths in secondary-bonded, primary-structures to achieve certification for civil transport aircraft. To meet this requirement, manufacturers commonly install redundant fasteners (~105 fasteners in a twin-aisle airframe with composite fuselage and wings), which add tremendous complexity, time and cost, and significantly reduce performance of the airframe. Under NASA’s Convergent Aeronautics Solutions (CAS) Program, the Adhesive Free Bonding of Composites (AERoBOND) project is investigating reformulated aerospace epoxy matrix resins to enable reflow and diffusion of the resin at the interface during a secondary bonding/cure process. The mixing process eliminates the material discontinuity at the interface, thereby removing the dependence of bond performance on adhesion across a nearly two-dimensional boundary. The AERoBOND interface is similar to the interlaminar region formed during a co-cure process, so joint performance depends on the cohesive properties of the matrix resin, which can be measured, inspected non-destructively, and certified for flight with fewer redundant fasteners. This presentation describes the ongoing development of stoichiometrically-offset epoxy resins to control the degree of cure in composite joints and enable interfacial mixing during secondary bonding/curing. Details on the resin formulation, laminate fabrication, and mechanical testing will also be presented. The precracked mode-II fracture toughness measured from preliminary AERoBOND joints was similar for joints fabricated with conventional epoxy matrix materials.

thermoset, hardener, prepreg, assembly↗
DOE OSTI2025

Direct Discontinuous Galerkin methods for the reacting multi-component flow equations

The Direct Discontinuous Galerkin (DDG (Liu and Yan, 2008)) method and a counterpart with Interface Correction (DDGIC (Danis and Yan, 2022)) are extended to compute diffusion terms that arise when solving the compressible multi-component flow equations in thermochemical nonequilibrium. Thermodynamic properties, transport properties, chemical reaction rates, and energy exchange terms are computed using Mutation++ (Scoggins et al., 2020). The DG method is applied on unstructured grids, where the accuracy and convergence rates can be sensitive to the numerical method chosen for parabolic terms. A method for determining the homogeneity tensor of the flow equations required for DDGIC is shown. The convergence properties of the DDG methods are studied and compared to the Interior Penalty (IP) method. A number of numerical experiments are conducted to assess the accuracy and performance of the method. The numerical results and convergence studies indicate that DDG and DDGIC provide accurate solutions and perform well for general flows in thermochemical nonequilibrium.

Diffusion↗
NASA NTRS1990

The diffusive boundary layer of sediments: oxygen microgradients over a microbial mat

Oxygen microelectrodes were used to analyze the distribution of the diffusive boundary layer (DBL) at the sediment-water interface in relation to surface topography and flow velocity. The sediment, collected from saline ponds, was covered by a microbial mat that had high oxygen consumption rate and well-defined surface structure. Diffusion through the DBL constituted an important rate limitation to the oxygen uptake of the sediment. The mean effective DBL thickness decreased from 0.59 to 0.16 mm as the flow velocity of the overlying water was increased from 0.3 to 7.7 cm s-1 (measured 1 cm above the mat). The oxygen uptake rate concurrently increased from 3.9 to 9.4 nmol cm-2 min-1. The effects of surface roughness and topography on the thickness and distribution of the DBL were studied by three-dimensional mapping of the sediment-water interface and the upper DBL boundary at 0.1-mm spatial resolution. The DBL boundary followed mat structures that had characteristic dimensions > 1/2 DBL thickness but the DBL had a dampened relief relative to the mat. The effective surface area of the sediment-water interface and of the upper DBL boundary were 31 and 14% larger, respectively, than a flat plane. Surface topography thereby increased the oxygen flux across the sediment-water interface by 49% relative to a one-dimensional diffusion flux calculated from the vertical oxygen microgradients.

NASA Center ARC↗
NASA NTRS2019

A Multi-Physics Study on High-Specific Power Li-O2 Batteries for Electric Aircraft

Commercialization of lithium-air batteries faces many challenges, such as electrolyte decomposition, short cycle life, low energy and power density, etc. However, commercialization of Li-O2 batteries for aeronautics is much more challenging due to additional safety constraints on cyclability and performance (high specific power and specific energy). For this presentation, we will discuss inter-related aspects of physics-based modeling of a pack: cell and battery model calibration. In addition, we will evaluate and present optimal battery designs for high discharge current density, high discharge time, and low battery mass using simulation-based optimization.The Finite Element Model (FEM) used to simulate a Li-O2 cell is based on the work of Bevara [1]. The different aspects of the model are based on: porous electrode theory and concentrated electrolyte theory; quantum tunneling model for the resistance of conformal layer of discharge product (Li2O2) [1]; Butler-Volmer kinetics for electrochemical reaction; Fick's diffusion for oxygen transport; and an oxygen dissolution model is applied at the air/electrolyte interface [2]. The electrolyte properties such as ion conductivity, ion diffusion, oxygen diffusion, and mass density of the electrolyte were taken from Molecular Dynamics (MD) simulations [3]; while the other model parameters, which includes mass of cell components, were calibrated to match experiments at high discharge current densities. The cell mass includes the anode, cathode, separator, electrolyte, and other components (such as current collector). This calibrated model is used to perform parametric studies on cathode thickness, porosity, tortuosity, carbon particle size, electrolyte transport and material properties, partial pressure of oxygen, discharge time, and discharge current density to study optimal designs for high specific power and energy. References:1. Bevara, V. & Andrei, P. (2014), J. Electrochem. Soc. 161 (14), A2068-A2079.2.Mehta, M. & Andrei, P. (2015), J. Power Sources. 286, 299-308.3.Liyana-Arachchi, T.; Haskins, J.; Burke, C.; Diederichsen, K.; McCloskey, B.; & Lawson, J. (2018), J. Phys. Chem. B. 122 (36), 8548 - 8559.4.Choi, W.; Kikumoto, H.; Choudhary, R. & Ooka, R. (2018), Applied Energy, 209, 306-321.

Mehta, Mohit↗
DOE OSTI2023

The Linkage Between Electro-Chemical Mechanical Instabilities in Battery Materials

Battery chemistry must be diversified to achieve a sustainable energy landscape by effectively utilizing renewable energy sources. Alkali metal-ion, all-solid-state, metal–air batteries, and multivalent batteries offer unique cost, safety, raw material abundance, energy, and power density solutions. However, realizing these “beyond Li-ion batteries” must uncover their working principles and performance & property relationships. In this aspect, mitigating chemo-mechanical instabilities in the structure and surface of the electrodes plays a crucial role in their performance. Unfortunately, the coupling between electrochemical and mechanical interactions is often poorly understood due to a lack of operando characterization. Here, this review article explains the working principles of curvature measurement and digital image correlation for measuring stress and strain generations in battery materials. We provided specific examples of how these operando mechanical measurements shed light on instabilities in alkali metal ion electrodes, solid electrolytes, Li-O 2 batteries, and aqueous Zn-ion batteries. Operando mechanical measurements offer an effective way to map changes in the physical fingerprint of the battery materials, therefore providing crucial information to elucidate instabilities in battery materials.

25 ENERGY STORAGE↗
DOE OSTI2020

Persistent compositions of non-stoichiometric compounds with low bulk diffusivity: A theory and application to Nb3Sn superconductors

Non-stoichiometric compounds may develop a composition gradient when they are formed by reactive diffusional processes. This paper reports an interesting phenomenon that in compounds with low bulk diffusivities, which rely mainly on grain boundary diffusion for their growth, the final bulk compositions may be far from equilibrium, with a very low bulk diffusivity leading to fixed (persistent) compositions – one such example is Nb 3 Sn, a superconductor. We investigated the microchemistry at the reactive interface using atom probe tomography to clarify the diffusion reaction mechanism for this low-bulk-diffusivity case and thus propose a theory for what determines the compound composition, using Nb 3 Sn as an example for concreteness. Using certain approximations, we derive an explicit analytical equation that illustrates what factors determine its composition profile. We compare our model with the known facts of Nb 3 Sn and see good agreement. In particular, this model predicts that internal oxidation may lead to higher Sn contents than conventional, non-oxidized Nb 3 Sn. Our measurements show that this is indeed true, and that the internally-oxidized Nb 3 Sn also has higher upper critical fields, achieving up to 28.2 T at 4.2 K. We discuss the general applicability of this model to non-stoichiometric compounds with low bulk diffusivity, and propose it as a tool to help in the design and processing of such materials for compositional control.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of Corrosion Resistant Coatings for Structural Materials for Liquid Fueled Molten Salts Reactors Applications (Final Report)

Current structural alloys, code certified for the MSRs temperature ranges, contain high levels of chromium, making them highly susceptible to molten halide salt corrosion. One potential solution to circumvent the need for code certification of novel alloys, which is expensive and time consuming, is to design claddings that will protect the underlying code certified materials from corrosion damage during operation. In this work, we examined the corrosion of Ni and Cu electroplated, Ni and CuNi weld overlay, Mo-laser clad, and carburized claddings on SS316H for use in molten salt reactor environments. After characterization of the cladded materials (Task 1), static corrosion tests were used to assess corrosion resistance of the claddings in typical molten fluoride salts (Task 2). The corrosion tests were performed in molten FLiNaK at 700°C up to 1000 hours. Pre- and post-corrosion Scanning Electron Microscopy (SEM), energy-dispersive-spectroscopy (EDS), Transmission Electron Microscopy (TEM), X-ray Diffraction (XRD) and glow-discharge-optical-emission-spectroscopy (GDOES) were performed on cladding cross-sections and surfaces to evaluate degradation. The Cu and Ni electroplated samples, as well as the carburized samples, showed excellent corrosion resistance relative to the bare SS316H. To assess high temperature cladding stability, ageing experiments were performed at temperatures up to 900 C in inert atmosphere for the electroplated and carburized samples and a diffusion model was developed to predict long term cladding behavior (Task 3). It was found that the Cu cladding was basically insensitive to the high temperature ageing, except for small secondary phases forming at the interface. On the other hand, the Ni electroplated cladding experienced significant interdiffusion. Nevertheless, the gain in corrosion resistance for a 100μm Ni electroplated cladding is phenomenal, with more than 50% reduction in chromium dissolution from the substrate material for the first 15 years of salt exposure at 700°C. To assess radiation resistance and phase stability, high-temperature 4MeV Ni heavy ion irradiation was performed across the cladding/substrate interface up to 50 displacement-per-atom (DPA) at 500°C and 700°C to assess the phase stability and irradiation behaviors of the electroplated systems (Task 4). The Ni and Cu electroplated systems did not experience void swelling at the contrary to the SS316H substrate due to their nanocrystalline nature. Some level of recrystallization was observed in the cladding, as well as radiation induced segregation and enhanced diffusion. The interface acted as a potent sink for point defects with the presence of a void denuded zone. The mechanical properties of the claddings were assessed using thermal shock, micro-indentation, nano-indentation, and four-point bend testing experiments (Task 5). These experiments were performed on the claddings in as-received, corroded, irradiated, and thermally aged states to determine the effects of typical molten salt reactor environments on cladding integrity. No significant mass loss was observed after repeated thermal shocks. While the electroplated samples softened after high-temperature ageing, irradiation hardening compensate this effect, such that there is little different with the as-received materials. The results of these experiments suggest that the electroplated (copper/nickel) show the greatest promise for application in molten salt reactor development. These claddings prevented any chromium dissolution from occurring during the static corrosion experiments. Additionally, they demonstrated favorable properties for high temperature diffusion, phase stability, interfacial mechanical properties, and irradiation resistance. Weld-overlay cladding are also of great interest and could reach properties similar to the electroplated samples upon optimization (especially with multiple weld passes). The carburized SS316H showed excellent behavior as well, but more work needs to be done to assess their long-term stability. Finally, the Mo-laser clad system was not pursued further due to the manufacturing challenges. It is also worth noting that the Ni cladding systems should behave relatively well in terms of weldability since the Ni-weld overlay microstructure and associated corrosion rate are sound. While the NiCu weld-overlay has even lower corrosion rates than the Ni-weld overlay, more studies on welding of Cu-electroplated systems are necessary since Cu clusters are known to embrittle steels.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Transient and diffusion analysis of Hg Cd Te

The solution of the one dimensional planar interface solidification problem is presented. Numerical solutions are applied to experimental solute profiles to determine the effective diffusion constant for Hg Co Te. Progress on the design and construction of a high gradient furnace is reported.

Clayton, J. C.↗
NASA NTRS2014

Microstructure and Oxidation of a MAX Phase/Superalloy Hybrid Interface

Corrosion resistant, strain tolerant MAX phase coatings are of interest for turbine applications. Thin Cr2AlC MAX phase wafers were vacuum diffusion bonded to an advanced turbine disk alloy, LSHR, at 1100 C. The interface, examined by optical and scanning electron microscopy, revealed a primary diffusion zone consisting of ~ 10 micrometers of beta-Ni(Co)Al, decorated with various NiCoCrAl, MC and M3B2 precipitates. On the Cr2AlC side, an additional ~40 micrometers Al-depletion zone of Cr7C3 formed in an interconnected network with the beta-Ni(Co)Al. Oxidation of an exposed edge at 800 C for 100 h produced a fine-grained lenticular alumina scale over Cr2AlC and beta-Ni(Co)Al, with coarser chromia granules over the Cr7C3 regions. Subsequent growth of the diffusion layers was only ~ 5 micrometers in total. A residual stress of ~ 500 MPa was estimated for the MAX phase layer, but no interfacial damage was observed. Subsequent tests for 1000 h reveal similar results.

heat resistant alloys↗
DOE OSTI2025

Unravelling Microstructure Selection in an Additively Manufactured Eutectic High‐Entropy Alloy

High-entropy alloys (HEAs) are promising candidates for advanced structural applications due to their excellent mechanical properties. Additive manufacturing (AM), with its rapid solidification conditions, enables the creation of unique nonequilibrium microstructures. To fully leverage the synergy between AM and HEAs, understanding how processing affects structure and properties is essential. Here, how solidification rate influences microstructure evolution and phase transformation pathway in laser additively manufactured AlCrFe2Ni2 eutectic HEAs is investigated. By increasing the laser scan speed and hence the solidification rate, distinct solidification modes evolving from coupled eutectic to anomalous eutectic and eventually to single-phase solidification are revealed. These transitions result in distinct microstructures and a wide range of mechanical properties. Thermodynamic modeling and molecular dynamics simulations reveal that low cooling rates allow for sufficient atomic diffusion and phase separation, facilitating coupled eutectic growth. In contrast, rapid cooling suppresses diffusion and destabilizes the solid–liquid interface, promoting anomalous or single-phase solidification. This integrated experimental and computational approach provides a multiscale understanding of solidification mechanisms in HEAs and underscores how kinetic effects can over-ride thermodynamic predictions under nonequilibrium conditions. Furthermore, these results demonstrate that AM can serve as a powerful tool to design HEAs with tailored microstructures and properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Fabrication of hybrid tin oxide‐cellulose nanocomposite as the flexible and thin supercapacitor

Abstract Microfibrillated cellulose (MFC) with reinforcing effects is a useful building block in the fabrication of flexible and thin supercapacitors. Herein, a hybrid tin oxide‐cellulose nanocomposite was hydrothermally produced and coated on MFC thin films to form a supercapacitor. The hybrid tin oxide‐cellulose thin films were structurally analyzed using scanning electrode microscopy, Fourier transform infrared spectroscopy and x‐ray diffraction. The cellulose thin film with the highest loading of hybrid tin oxide‐cellulose nanocomposite exhibited a specific capacitance of 225.88 F g −1 at 100 mV s −1 and 486.38 F g −1 at 20 mV s −1 in the three‐electrode electrochemical system. In addition, it revealed good cyclic stability up to 40 cycles run continuously with 95% cyclic retention. The high specific capacitance and superior cyclic stability could be related to the enhanced charge mobility and ion diffusion between the solid and electrolyte interface. The cellulose thin film coated with flower‐like hybrid nanocomposite showed great potential in energy storage.

Letchumanan, Iswary↗
DOE OSTI2024

A mineral precipitation model based on the volume of fluid method

A novel volume of fluid method is presented for mineral precipitation coupled with fluid flow and reactive transport. The approach describes the fluid-solid interface as a smooth transitional region, which is designed to provide the same precipitation rate and viscous drag force as a sharp interface. Specifically, the governing equation of mineral precipitation is discretized by an upwind scheme, and a rigorous effective viscosity model is derived around the interface. The model is validated against analytical solutions for mineral precipitation in channel and ring-shaped structures. It also compares well with interface tracking simulations of advection-diffusion-reaction problems. Here, the methodology is finally employed to model mineral precipitation in fracture networks, which is challenging due to the low porosity and complex geometry. Compared to other approaches, the proposed model has a concise algorithm and contains no free parameters. In the modeling, only the pore space requires meshing, which improves the computational effciency especially for low-porosity media.

58 GEOSCIENCES↗
DOE OSTI2020

Oxide structure of air-passivated U-6Nb alloy thin films

U-6Nb is a uranium alloy containing 6 wt% niobium that possesses high corrosion resistance. The structure and composition of the passivating oxide layer formed on air-aged U-6Nb, which gives the material its corrosion resistant properties, was characterized using surface scattering techniques. Stable oxide layers formed on the surface of a set of U-6Nb alloy thin films under ambient conditions were investigated using neutron reflectometry (NR), x-ray reflectometry (XRR) and grazing incidence x-ray diffraction (GIXD). The passivating oxide was composed of approximately 27% U, 5% Nb, and 68% O, primarily consisting of a thin niobium oxide layer (5.5 ± 0.4 nm) separating a thicker UO2 layer (27.1 ± 2.3 nm) from the underlying U-6Nb alloy. A critical density of enriched niobium oxide at the metal-oxide interface is hypothesized to limit oxygen diffusion and confer high corrosion resistance to the alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Kinetic pathways of fast lithium transport in solid electrolyte interphases with discrete inorganic components

The transport of lithium ions in the solid electrolyte interphase (SEI) has been previously accepted to proceed in two steps: a fast pore diffusion through the outer, porous organic layer followed by a slow knock-off or vacancy diffusion in the inner, dense inorganic layer. The second step is believed to be the rate-limiting step during fast-charging. In this study, we have intentionally constructed a thicker SEI (SEI-rich) structure on the surface of monoclinic Nb 2 O 5 (H-Nb 2 O 5 ) by adding LiNO 3 into a conventional ethylene carbonate based electrolyte. The electrochemical performance of two electrodes, one SEI-rich and one with few SEI (SEI-lean), was found to be almost the same, including their fast-charging capability and cycling stability, despite the significant difference in their SEI structure. Importantly, analysis using cryogenic scanning/transmission electron microscopy showed the discrete decoration of individual inorganic particles (e.g., Li 2 O) and amorphous species (LiN x O y /organic components) over the surface of H-Nb 2 O 5 . These discrete inorganic particles are in contradiction to the formation of dense inner inorganic layer, which has been commonly postulated. Based on these findings, we propose a new mechanism for Li ion transport through the SEI: one-step pore diffusion, without the second step slow diffusion. This one-step pore diffusion process provides an extremely fast Li ion transport, and effectively removes the kinetic limitation of Li ion transport in the SEI for fast charging. Finally, these results strongly suggest that the influence of SEI structure on the transport kinetics of lithium ions is much less significant than previously accepted. These results offer a new understanding of possible lithium ion transport pathway within SEI and may have implications for the future designs of fast-charging battery materials.

25 ENERGY STORAGE↗
DOE OSTI2023

Convection-Induced Compositional Patterning at Grain Boundaries in Irradiated Alloys

We consider the stability of precipitates formed at grain boundaries (GBs) by radiation-induced segregation in dilute alloys subjected to irradiation. Here, the effects of grain size and misorientation of symmetric-tilt GBs are quantified using phase field modeling. A novel regime is identified where, at long times, GBs are decorated by precipitate patterns that resist coarsening. Maps of the chemical Péclet number indicate that arrested coarsening takes place when solute advection dominates over thermal diffusion right up to the precipitate/matrix interface, preventing interfacial local equilibrium and overriding capillary effects. This contrasts with liquid-solid mixtures where convection always accelerates coarsening.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Structuring, stochastic behavior, and charge storage capacity of redox-active microemulsions formulated with mixtures of toluene and ionic liquid as oil phase

Oil/water microemulsions (µEs) are promising electrolytes for redox flow batteries (RFBs) as they simultaneously improve charge capacity and ionic conductivity. Here, we report the successful formulation of bicontinuous µEs where the oil phase is a solution of trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl)amide ionic liquid in toluene with redox-active ferrocene. We examined the effect of supporting electrolyte anion (NO 3 – , Cl – , ClO 4 – ) on the structure, reactivity, transport, and electrolytic performance of redox-active µEs. Neutron scattering and nuclear magnetic resonance showed that the domain size increased as Cl – > NO 3 – > ClO 4 – while the ferrocene diffusion coefficient increased as NO 3 – > Cl – > ClO 4 – . Scanning electrochemical microscopy indicated anion-dependent current fluctuations during electrolysis, with ClO 4 – exhibiting the least high-frequency oscillations, which correlate to the highest charge and discharge capacity and reversibility. All ionic liquid containing systems improved the performance of toluene-based µEs, highlighting new design principles for these electrolytes.

diffusion↗
DOE OSTI2020

Advancing PV material performance using nanoscale opto-electrical characterization

The purpose of this program was to improve the efficiency of photovoltaics by characterizing their optoelectronic properties at the nanoscale. We investigated Copper Indium Gallium Selenide (CIGS) materials produced by Dow. We modified an atomic force microscope (AFM) to work with a highly controlled environment under controlled illumination at the probe to study the main power conversion efficiency determining parameters for photovoltaics of open circuit voltage, short circuit current, carrier lifetime and diffusion length, and band alignment at interfaces and defects with sub 10nm spatial resolution of their device materials.

14 SOLAR ENERGY↗