Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “impurity concentration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The role of chemical potential in compensation control in Si:AlGaN

Reduction in compensation in Si-doped Al-rich AlGaN is demonstrated via chemical potential control (CPC). The chemical potentials and the resulting formation energies of carbon on the nitrogen site (C N ) and cation vacancy complex with Si (V III + nSi III ) were related to growth variables through a thermodynamic supersaturation model, which quantitatively predicted the incorporation of C N and the generation of the V III + nSi III complex. The compensation “knee” behavior, i.e., decreasing conductivity with increasing Si incorporation beyond a certain concentration, was successfully controlled. The maximum free carrier concentration was improved by impeding the formation of V III + nSIi III complexes under III-richer conditions, while the impurity compensation by C N was reduced by making the growth environment N-richer. The results of Hall effect measurement and photoluminescence agreed well with quantitative theoretical predictions of the CPC model. Based on the developed model, the highest conductivity of 160 Ω -1 cm -1 with free carrier concentration of 3 × 10 19 cm -3 in Al 0.7 Ga 0.3 N ever reported was achieved on single crystal AlN substrates. The demonstrated predictive power of the CPC model should greatly reduce the empirical analysis or iterative experimentation that would otherwise be necessary.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

The impact of nickel concentration and stacking fault energy on deformation mechanisms in high-purity austenitic Fe-Cr-Ni alloys

Understanding how composition affects deformation mechanisms in austenitic stainless steels is essential for developing accurate predictive models of stress-induced failures and stress corrosion cracking. Nickel (Ni), an element classified as a critical element, plays a crucial role in these processes. It is important to examine how Ni concentration influences stacking fault energy (SFE) and, consequently, the deformation mechanisms of austenitic stainless steels. However, in commercial stainless steels, the effects of other alloying elements and impurities can obscure Ni's role, complicating efforts to isolate its impact. Here, in this study, we use two high-purity Fe-Cr-Ni alloys to investigate how Ni concentration and SFE interact to alter deformation mechanisms and induce martensitic transformation. By combining in situ synchrotron X-ray diffraction (XRD) tensile testing and post-mortem electron microscopy with density functional theory simulations, we gain precise insights into these phenomena. We find that the Fe18Cr10Ni (wt%) alloy, with its low SFE, exhibits higher stacking fault probability, deformation-induced martensitic transformation, and a lesser increase in dislocation density with plastic strain. In contrast, the Fe18Cr14Ni (wt%) alloy, with its higher SFE, shows enhanced deformation twinning and greater dislocation density with increasing strain. These findings from high-purity ternary alloys provide valuable insights that can guide the search for alternative elements to replace Ni while achieving similar effects on phase stability and deformation behavior.

36 MATERIALS SCIENCE↗
NASA NTRS1982

A system for measuring thermal activation energy levels in silicon by thermally stimulated capacitance

One method being used to determine energy level(s) and electrical activity of impurities in silicon is described. The method is called capacitance transient spectroscopy (CTS). It can be classified into three basic categories: the thermally stimulated capacitance method, the voltage-stimulated capacitance method, and the light-stimulated capacitance method; the first two categories are discussed. From the total change in capacitance and the time constant of the capacitance response, emission rates, energy levels, and trap concentrations can be determined. A major advantage of using CTS is its ability to detect the presence of electrically active impurities that are invisible to other techniques, such as Zeeman effect atomic absorption, and the ability to detect more than one electrically active impurity in a sample. Examples of detection of majority and minority carrier traps from gold donor and acceptor centers in silicon using the capacitance transient spectrometer are given to illustrate the method and its sensitivity.

Cockrum, R. H.↗
NASA NTRS1986

Optical and electrical characterizations of laser-chemical-vapor-deposited aluminum oxynitride films

Composition-dependent optical and electrical properties of L-CVD (Al2O3)1-c-(AlN)c composite films are examined. The optical properties exhibit a continuous change from Al2O3 to AlN with increasing value of the composition parameter c from zero to one. There is a critical concentration value of about 0.3 below and above which Al2O3- and AlN-like optical properties are observed. The impurity absorption regions are 5.1-6.7 eV for Al2O32 and 4.6-6.0 for AlN, while the energy gap is about 6.7 eV for Al2O3 and 6.0 eV for AlN. The electrical properties of Al-insulator n-Si MIS structures display externally programmable states when bulk-controlled electron emission occurs from the traps. In the high-field region a persistent polarization field is established within the insulator. C-V characteristics of the samples are more sensitive to the concentration factor c than the I-V characteristics. A large clockwise hysteresis is observed for AlN, but a smaller counterclockwise one is observed for Al2O3.

Demiryont, H.↗
DOE OSTI2021

Generalized impurity pinch in partially magnetized multi-ion plasma

In a two-ion-species plasma with disparate ion masses, heavy ions tend to concentrate in the low-temperature region of collisionally magnetized plasma and in the high-temperature region of collisionally unmagnetized plasma, respectively. Moreover, collisional magnetization can be determined as the ratio of the light ion gyrofrequency to the collision frequency of light and heavy ion species, and the behavior of this effect in the intermediate regime of partially magnetized plasma is predominantly dependent on this Hall parameter. Multi-ion cross-field transport has been described before in the collisionally magnetized plasma regime, and generalized pinch relations, which describe densities of ion species in equilibrium in that plasma, are found in the literature. Here, the role of collisional magnetization and Larmor magnetization in multi-ion collisional transport is clarified, and generalized pinch relations are extended to the partially magnetized regime in which the ion Hall parameter may be small, as long as electrons remain collisionally magnetized. Equilibrium ion density profiles have the same dependence on external forces and on each other regardless of collisional magnetization of ions. The expansion of the range of validity of multi-ion collisional transport models makes them applicable to a wider range of laboratory plasma conditions. In particular, ion density profiles evolve sufficiently fast for radial impurity transport to be observable around stagnation on MagLIF, leading to expulsion of heavy ion impurities from the hotspot as long as plasma becomes sufficiently collisionally magnetized during the implosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1979

Utilization of nuclear methods for materials analysis and the determination of concentration gradients

The various types of nuclear chemical analysis methods are discussed. The possibilities of analysis through activation and direct observation of nuclear reactions are described. Such methods make it possible to analyze trace elements and impurities with selectivity, accuracy, and a high degree of sensitivity. Such methods are used in measuring major elements present in materials which are available for analysis only in small quantities. These methods are well suited to superficial analyses and to determination of concentration gradients; provided the nature and energy of the incident particles are chosen judiciously. Typical examples of steels, pure iron and refractory metals are illustrated.

Darras, R.↗
NASA NTRS2014

The GOddard SnoW Impurity Module (GOSWIM) for the NASA GEOS-5 Earth System Model: Preliminary Comparisons with Observations in Sapporo, Japan

The snow darkening module evaluating dust, black carbon, and organic carbon depositions on mass and albedo has been developed for the NASA Goddard Earth Observing System, Version 5 (GEOS-5) Earth System Model, as the GOddard SnoW Impurity Module (GOSWIM). GOSWIM consists of the snow albedo scheme from a previous study (Yasunari et al. 2011) with updates and a newly developed mass concentration scheme, using aerosol depositions from the chemical transport model (GOCART) in GEOS-5. Compared to observations at Sapporo, the numerical experiments, forced by observation-based meteorology and aerosol depositions from GOES-5, better simulated the seasonal migration of snow depth, albedos, and impurities of dust, BC, and OC in the snow surface. However, the magnitude of the impurities is underestimated, compared to the sporadic snow impurity measurements. Increasing the deposition rates of dust and BC could explain the differences on the snow darkening effect between observation and simulation. Ignoring BC deposition can possibly lead to an extension of snow cover duration in Sapporo for four days. Comparing the off-line GOSWIM and the GEOS-5 global simulations, we found that determining better local precipitation and deposition rates of the aerosols are key factors in generating better GOSWIM snow darkening simulation in NASA GEOS-5.

land surface processes↗
DOE OSTI2020

Scalable Substitutional Re‐Doping and its Impact on the Optical and Electronic Properties of Tungsten Diselenide

Abstract Reliable, controlled doping of 2D transition metal dichalcogenides will enable the realization of next‐generation electronic, logic‐memory, and magnetic devices based on these materials. However, to date, accurate control over dopant concentration and scalability of the process remains a challenge. Here, a systematic study of scalable in situ doping of fully coalesced 2D WSe 2 films with Re atoms via metal–organic chemical vapor deposition is reported. Dopant concentrations are uniformly distributed over the substrate surface, with precisely controlled concentrations down to <0.001% Re achieved by tuning the precursor partial pressure. Moreover, the impact of doping on morphological, chemical, optical, and electronic properties of WSe 2 is elucidated with detailed experimental and theoretical examinations, confirming that the substitutional doping of Re at the W site leads to n‐type behavior of WSe 2 . Transport characteristics of fabricated back‐gated field‐effect‐transistors are directly correlated to the dopant concentration, with degrading device performances for doping concentrations exceeding 1% of Re. The study demonstrates a viable approach to introducing true dopant‐level impurities with high precision, which can be scaled up to batch production for applications beyond digital electronics.

Kozhakhmetov, Azimkhan↗
DOE OSTI2024

Electrodialysis: An effective methodology to purify the leachate of spent Li-ion batteries

The electrification of transportation and the transition of society towards low or net-zero carbon emissions has led to a skyrocketing global demand for Li-ion batteries. After a service life of three to ten years, Li-ion batteries have less than 80 % of their initial capacities and draw near to the end of their lives for practical utilization. Due to potential supply chain shortages and the value embodied in Li-ion batteries, it is imperative to recycle them, to recover the materials, and to improve the circularity and the sustinability of the industry. How to cost-effectively purify spent batteries while reducing time, energy, and waste emissions is a challenge faced by Li-ion battery recyclers. The first electrochemical membrane reactor reported in our group hasa high selectivity towards lower Cu 2+ , Al 3+ and Fe 3+ ions (<5 ppm) and retains >95% of the Ni 2+ , Co 2+ and Mn 2+ ions in the leachate. An advanced electrochemical membrane reactor was developed in this study. Further, not only does the new reactor have the same selectivity as the original reactor, but other advantages including a faster leachate processing rate (up to 10X faster). The advanced reactor can also directly generate acid at the anode side; eliminating the reactor restoration step. The prominent advantages that this electrodialysis technology has over chemical-precipitation methods include: (1) ion recovery efficiencies do not diminish after removing the impurities, Ni 2+ , Co 2+ and Mn 2+ , even at a higher initial Ni 2+ ion concentrations; in comparison, chemical precipitation has Ni 2+ , Co 2+ and Mn 2+ ion recovery efficiencies reduced significantly when the initial Ni 2+ , Co 2+ and Mn 2+ ion concentrations increase. (2) electrodialysis does not change the concentrations of Ni 2+ , Co 2+ and Mn 2+ ions significantly, but chemical precipitation could reduce Ni 2+ and Co 2+ ions to less than half of their initial values. Through electro-dialyzing the leachate, the H 2 evolution reaction mechanism was found to switch from the Volmer-acid Heyrovsky mechanism to the Volmer-alkaline Heyrovsky mechanism at a pH of around 3.7.

25 ENERGY STORAGE↗
DOE OSTI2025

Production of a δ-Lactam from Glucose through Integrating Biological and Chemical Catalysis

We present a new strategy for the production of a δ-lactam from glucose that integrates biological production of triacetic acid lactone (TAL, 4-hydroxy-6-methyl-2H-2-one) with catalytic transformation of TAL into 6-methylpiperidin-2-one (MPO) through metabolic engineering, isomerization, amination, and catalytic hydrogenation/hydrogenolysis. We developed a sustainable and antibiotic-free fed-batch fermentation using genetically modified Rhodotorula toruloides IFO0880. This process achieved a yield of 2-hydroxy-6-methyl-4H-pyran-4-one (2H4P) at 0.05 g/g of glucose, corresponding to a 9.9 g/L titer. By adjusting the pH of the fermentation broth to 2, 2H4P was quantitatively converted into TAL. The TAL in the fermentation broth was directly converted by aminolysis into 4-hydroxy-6-methylpyridin-2(1H)-one (HMPO), which achieved an 18.5% yield with 94.3% purity. The HMPO yield was lower in the fermentation broth than in a clean feedstock (32.2%), suggesting that the biological impurities are inhibitors in this reaction. Further investigation revealed that lower pH levels and reduced TAL concentrations in the fermentation broth significantly decreased HMPO yields. Subsequently, the precipitated HMPO was filtered and dried and then subjected to the final catalytic conversion in H2O solvent, achieving a MPO yield of 91.8%. Furthermore, this integrated approach demonstrated the direct use of TAL in the filtered aqueous fermentation broth without the need to isolate TAL.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Data for Production of a δ-Lactam from Glucose through Integrating Biological and Chemical Catalysis

We present a new strategy for the production of a δ-lactam from glucose that integrates biological production of triacetic acid lactone (TAL, 4-hydroxy-6-methyl-2H-2-one) with catalytic transformation of TAL into 6-methylpiperidin-2-one (MPO) through metabolic engineering, isomerization, amination, and catalytic hydrogenation/hydrogenolysis. We developed a sustainable and antibiotic-free fed-batch fermentation using genetically modified Rhodotorula toruloides IFO0880. This process achieved a yield of 2-hydroxy-6-methyl-4H-pyran-4-one (2H4P) at 0.05 g/g of glucose, corresponding to a 9.9 g/L titer. By adjusting the pH of the fermentation broth to 2, 2H4P was quantitatively converted into TAL. The TAL in the fermentation broth was directly converted by aminolysis into 4-hydroxy-6-methylpyridin-2(1H)-one (HMPO), which achieved an 18.5% yield with 94.3% purity. The HMPO yield was lower in the fermentation broth than in a clean feedstock (32.2%), suggesting that the biological impurities are inhibitors in this reaction. Further investigation revealed that lower pH levels and reduced TAL concentrations in the fermentation broth significantly decreased HMPO yields. Subsequently, the precipitated HMPO was filtered and dried and then subjected to the final catalytic conversion in H2O solvent, achieving a MPO yield of 91.8%. This integrated approach demonstrated the direct use of TAL in the filtered aqueous fermentation broth without the need to isolate TAL.

Catalysis↗
NASA NTRS1986

Effects of macroscopic inhomogeneities on electron mobility in semi-insulating GaAs

It is shown that defect inhomogeneities of sizes larger than the electron mean free path are responsible for the low values and anomalous temperature dependence of the electron mobility in semi-insulating (SI) GaAs. The room-temperature electron mobility values below about 6000 sq cm/V s cannot be uniquely used for the determination of the concentration of ionized defects, since the contribution from inhomogeneities usually exceeds that from scattering by ionized impurities. The effects of the macroscopically inhomogeneous distribution of residual acceptors and the major deep donor EL2 diminish at elevated temperatures between 600 and 900 K, which offers a means for identification of inhomogeneities, and furthermore explains recently reported steplike mobility versus temperature behavior in SI-GaAs.

Walukiewicz, W.↗
NASA NTRS1998

Protein Crystal Growth Under Forced Solution Flow: Experimental Setup and General Response of Lysozyme

We have experimentally studied the effects of solution flow on the growth kinetics of the protein lysozyme. To this end, we have expanded our interferometry setup by a novel crystallization cell and solution recirculation system. This combination permits monitoring of interface morphology and kinetics with a depth resolution of 200 A at bulk flow rates of up to 2000 micron/s. Particular attention was paid to the prevention of protein denaturation that is often associated with the pumping of protein solutions. We found that at bulk flow rates it less than 250 microns/s the average growth rate and step velocity, R(sub avg) and upsilon(sub avg) increase with increasing it. This can be quantitatively understood in terms of the enhanced, convective solute supply to the interface. With high-purity solutions, it u greater than 250 microns/s lead to growth deceleration, and, at low supersaturations sigma, to growth cessation. When solutions containing approx. 1% of other protein impurities were used, growth deceleration occurred at any u greater than 0 and cessation in the low sigma experiments was reached at about half the it causing cessation with pure solution. The flow-induced changes in R(sub avg) and upsilon(sub avg) including growth cessation, were reversible and reproducible, independent of the direction of the u-changes and solution purity. Hence, we attribute the deceleration to the convection-enhanced supply of impurities to the interface, which at higher flow rates overpowers the effects of enhanced interfacial solute concentration. Most importantly, we found that convective transport leads to a significant reduction in kinetics fluctuations, in agreement with our earlier expectations for the lysozyme system. This supports our hypothesis that these long-term fluctuations represent an intrinsic response feature of the coupled bulk transport-interfacial kinetics system in the mixed growth control regime.

Vekilov, P. G.↗
NASA NTRS1979

Material science and solid state physics studies with positive muon spin precession

The hyperfine field on the muon, B sub hf, at interstitial sites in dilute Fe(Al) alloys was measured for four different concentrations of Al and as a function of temperature by the muon spin rotation method. The magnitude of B sub hf, which is negative, decreases at rates ranging from 0.09 + or - 0.03% per at.% Al at 200 K to an asymptotic limit of 0.35 + or - far above 440 K. This behavior shows that sites near the Al impurity are weakly repulsive to the muon, with an interaction potential of 13 + or - 3 meV. In order to fit the temperature dependence of the hyperfine field, it is necessary to hypothesize the existence of a small concentration of unidentified defects, possibly dislocations, which are attractive to the muon. Although the Al impurity acts as a non-magnetic hole in the Fe lattice, the observed decrease in B sub hf is only 35% of the decrease in the bulk magnetization. It is concluded that B sub hf is determined mainly by the enhanced screening of conduction electrons in Fe and Fe(Al). Since the influence of the Al impurity on the neighboring Fe monents is very small, most of the change in B sub hf is therefore attributed to the increase in conduction electron polarization of the Al impurity.

Stronach, C. E.↗
DOE OSTI2022

Removal of Tc-99, Zr-95, and Nb-95, From Solutions Obtained After Dissolution of Irradiated Mo Targets

Decontamination of 99 Tc, Nb, and Zr impurities in dissolved irradiated Mo disks can be accomplished using Fe(II) precipitation. Here, we report bench-scale experiments and large-scale demonstrations on removal of 99 Tc (0.1 mM), 95 Nb, and 95 Zr from dissolved Mo disk simulant solutions. Tc removal is accomplished through the reduction and simultaneous immobilization of Tc(VII) by Fe(II), producing an insoluble, Tcincorporated Fe(II)-Fe(III) solid that is removed by filtration. Large-scale testing showed that Tc (97.6% ± 1.7%) is removed without affecting 99 Mo yields. Other important side reaction product impurities in irradiated Mo targets, namely various isotopes of Nb and Zr, are also removed (>99%) in this process. The effects of metal (Fe, Tc, Mo) concentrations, Fe(II)/Fe(III) ratio, pH, temperature, Fe addition method, and hydrogen peroxide addition were tested. The minimum amount of Fe(II) needed to remove up to 99% Tc is 10 mM and the optimal pH value for simultaneous removal of Tc, Nb, and Zr impurities is pH 13.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2000

The Effect of Hydrogen Annealing on the Impurity Content of Alumina-Forming Alloys

Previously, the effect of hydrogen annealing on increasing the adhesion of Al2O3 scales had been related to the effective desulfurization that occurred during this process. The simultaneous reduction of other impurities has now been re-examined for up to 20 impurity elements in the case of five different alloys (NiCrAl, FeCrAl, PWA 1480, Rene'142, and Rene'N5). Hydrogen annealing produced measurable reductions in elemental concentration for B, C, Na, Mg, P, K, Sr, or Sn in varying degrees for at least one and up to three of these alloys. No single element was reduced by hydrogen annealing for all the alloys except sulfur. In many cases spalling occurred at low levels of these other impurities, while in other cases the scales were adherent at high levels of the impurities. No impurity besides sulfur was strongly correlated with adhesion.

Smialek, James L.↗