Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “glass transition temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

The glass transition, crystallization and melting in Au-Pb-Sb alloys

The glass transition, crystallization and melting of Au(55)Pb(22.5)Sb(22.5) alloys have been studied by differential scanning calorimetry DSC. Crystallization on heating above the glass transition temperature Tg (45 C) begins at 64 C. Further crystallization events are observed at 172 C and 205 C. These events were found to correspond to the formation of the intermetallic compounds AuSb2, Au2Pb, and possibly AuPb2, respectively. Isothermal DSC scans of the glassy alloy above Tg were used to monitor the kinetics of crystallization. The solidification behavior and heat capacity in the glass-forming composition range were determined with droplet samples. An undercooling level of 0.3T(L) below the liquidus temperature T(L) was achieved, resulting in crystallization of different stable and metastable phases. The heat capacity C(P) of the undercooled liquid was measured over an undercooling range of 145 C.

Lee, M. C.↗
DOE OSTI2020

Multiamorphous Phases in Diketopyrrolopyrrole-Based Conjugated Polymers: From Bulk to Ultrathin Films

The glass transition temperature (T g ) of conjugated polymers is a crucial physical parameter that governs their mechanical and electrical properties for applications from sensor technology to skin-like electronics. Despite some well-developed methods that exist for detecting T g of conjugated polymers, there is still a need for the combination of advanced calorimetric methodologies to characterize T g in a broad range of temperatures and scales from bulk to nanometer-thin films. In this work, alternating current (ac) chip calorimetry and flash differential scanning calorimetry (flash DSC) are applied to successfully identify the Tgs and segmental relaxations of conjugated polymers. The detected relaxations were interpreted, in agreement with existing observations in similar systems, as a side-chain relaxation (low temperature), mobile amorphous fractions (MAF), and rigid amorphous fractions (RAF). T g s of MAF and RAF increase and decrease with increasing size of fused thiophene units in the backbone, respectively. The T g s of diketopyrrolopyrrole-based conjugated polymer thin films are also identified by the same method, with both T g s showing a decreased value compared to those of bulk samples. Furthermore, the weight fractions of MAF and RAF with various film thicknesses are qualitatively analyzed based on the heat capacity step of each amorphous fraction during the glass transition. This facile method gives insights into the physical nature of amorphous phases in conjugated polymers for better revealing their structure-property relationships, which will guide the designs of new materials with optimized electrical and mechanical properties in the future.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2009

Liquid Crystalline Thermosets from Ester, Ester-imide, and Ester-amide Oligomers

Main chain thermotropic liquid crystal esters, ester-imides, and ester-amides were prepared from AA, BB, and AB type monomeric materials and end-capped with phenylacetylene, phenylmaleimide, or nadimide reactive end-groups. The end-capped liquid crystal oligomers are thermotropic and have, preferably, molecular weights in the range of approximately 1000-15,000 grams per mole. The end-capped liquid crystaloligomers have broad liquid crystalline melting ranges and exhibit high melt stability and very low melt viscosities at accessible temperatures. The end-capped liquid crystal oli-gomers are stable forup to an hour in the melt phase. They are highly processable by a variety of melt process shape forming and blending techniques. Once processed and shaped, the end-capped liquid crystal oigomers were heated to further polymerize and form liquid crystalline thermosets (LCT). The fully cured products are rubbers above their glass transition temperatures.

Dingemans, Theodorus J.↗
DOE OSTI2024

A General Approach to Activate Second‐Scale Room Temperature Photoluminescence in Organic Small Molecules

Organic small molecules that exhibit second‐scale phosphorescence at room temperature are of interest for potential applications in sensing, anticounterfeiting, and bioimaging. However, such materials systems are uncommon—requiring millisecond to second‐scale triplet lifetimes, efficient intersystem crossing, and slow rates of nonradiative recombination. Here, a simple and scalable approach is demonstrated to activate long‐lived phosphorescence in a wide variety of molecules by suspending them in rigid polymer hosts and annealing them above the polymer's glass transition temperature. This process produces submicron aggregates of the chromophore, which suppresses intramolecular motion that leads to nonradiative recombination and minimizes triplet–triplet annihilation that quenches phosphorescence in larger aggregates. In some cases, evidence of excimer‐mediated intersystem crossing that enhances triplet generation in aggregated chromophores is found. In short, this approach circumvents the current design rules for long‐lived phosphors, which will streamline their discovery and development.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Carbazole-Based Hole-Transport Materials for High-Efficiency and Stable Perovskite Solar Cells

As organic–inorganic halide perovskite solar cells (PSCs) near commercialization, stability challenges during real-world conditions, such as durability at elevated temperatures, still need to be addressed. We have previously reported that doping of triarylamine-based hole-transport layers (HTLs) with a triarylamine-based radical cation salt (EHCz-3EtCz/EH44-ox) leads to enhanced PSC stability at elevated temperatures. While it was shown the radical cation dopant did not need to be identical to the HTL matrix, little was known about dopant exchange to realize the maximum impact on device-level properties (e.g., increase in low intrinsic conductivity, mobility, hydrophobic properties, ease of synthesis, and thermal stability). In this paper, we study the impact of dopant exchange among stable, low-cost, high-glass-transition temperature (Tg), and easily synthesized triarylamine-based HTL and radical triarylamine cation salts as dopants. Using EH44-ox as dopant leads to the improved device-level power conversion efficiency (PCE) for all HTL matrices assessed. Moreover, increasing the number of ethylhexyl chains from one to two per molecule and positioning these chains at the periphery rather than the core resulted in improved hydrophobicity. PSCs based on our HTL formulations have similar power conversion efficiencies (PCE) as those of PSCs based on commercially available HTLs while demonstrating greatly improved device-level stability at elevated temperatures.

14 SOLAR ENERGY↗
DOE OSTI2023

Discovery of multi-functional polyimides through high-throughput screening using explainable machine learning

Polyimides have been widely used in modern industries because of their excellent mechanical and thermal properties, e.g., high-temperature fuel cells, displays, and aerospace composites. However, it usually takes decades of experimental efforts to develop a successful product. Aiming to expedite the discovery of high-performance polyimides, we utilize computational methods of machine learning (ML) and molecular dynamics (MD) simulations. Our study provides compelling evidence for the effectiveness of a data-driven approach in discovering novel polyimides. We first build a comprehensive library of more than 8 million hypothetical polyimides based on the polycondensation of existing dianhydride and diamine/diisocyanate molecules. Then we establish multiple ML models for the thermal and mechanical properties of polyimides based on their experimentally reported values, including glass transition temperature, Young’s modulus, and tensile yield strength. The obtained ML models demonstrate excellent predictive performance in identifying the key chemical substructures influencing the thermal and mechanical properties of polyimides. The use of explainable machine learning describes the effect of chemical substructures on individual properties, from which human experts can understand the cause of the ML model decision. Applying the well-trained ML models, we obtain property predictions of the 8 million hypothetical polyimides. Then, we screen the whole hypothetical dataset and identify three (3) best-performing novel polyimides that have better-combined properties than existing ones through Pareto frontier analysis. For an easy query of the discovered high-performing polyimides, we also create an online platform https://polyimide-explorer.herokuapp.com/ that embeds the developed ML model with interactive visualization. Furthermore, we validate the ML predictions through all-atom MD simulations and examine their synthesizability. The MD simulations are in good agreement with the ML predictions and the three novel polyimides are predicted to be easy to synthesize via Schuffenhauer’s synthetic accessibility score. Following the proposed ML guidance, we successfully synthesized a novel polyimide and the experimentally obtained high glass transition/thermal decomposition temperature demonstrated its excellent thermal stability. Here our study demonstrates an efficient way to expedite the discovery of novel polymers using ML prediction and MD validation. The high-throughput screening of a large computational dataset can serve as a general approach for new material discovery in other polymeric material exploration problems, such as organic photovoltaics, polymer membranes, and dielectrics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Role of Fast Dynamics in Conductivity of Polymerized Ionic Liquids

Polymerized ionic liquids (PolyILs) are promising candidates for a broad range of technologies. However, the relatively low conductivity of PolyILs at room temperature has strongly limited their applications. In this work, we provide new insights into the roles of various microscopic parameters controlling ion transport in these polymers, which are crucial for their rational design and practical applications. Using broadband dielectric spectroscopy and neutron and light scattering techniques, we found a clear connection between the activation energy for conductivity, fast dynamics, and high-frequency shear modulus in PolyILs at their glass transition temperature (T g ). In particular, our analysis reveals a correlation between conductivity and the amplitude of fast picosecond fluctuations at T g , suggesting the possible involvement of fast dynamics in lowering the energy barrier for ion conductivity. We also demonstrate that both the activation energy for ion transport and the amplitude of the fast fluctuations depend on the high-frequency shear moduli of PolyILs, thus identifying a practically important parameter for tuning conductivity. Finally, the parameters recognized in this work and their connection to the ionic conductivity of PolyILs set the stage for a deeper understanding of the mechanism of ion transport in PolyILs in the glassy state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1983

Dynamic Mechanical Properties of N-Phenylnadimide Modified PMR Polyimide Composites

The rheological behavior of newly developd Celion 6000/N-phenylnadimide modified PMR polyimide and PMR-15 composites was investigated. The dynamic mechanical properties were correlated with the structure of N-phenylnadimide modified PMR polyimides. The storage modulus (G'), loss modulus (G''), and loss tangent (tan delta) of four composite systems were measured over a temperature range from -150 to 400 C. Three well defined peaks were seen in the regions of 360, 100, and -120 C, corresponding to the alpha, beta, and gamma relaxations, respectively, of the matrix resins. The activation energies of the alpha, beta, and gamma relaxations were estimated to be 232, 60, and 14 kcal/mole, respectively, for PMR-15. Addition of N-phenylnadimide to the PMR-15 composition lowered the glass transition temperature and the activation energies of PMR-15 polyimide. The dynamic mechanical data appear to be consistent with the formation of a copolymer from N-phenylnadimide and a PMR-15 prepolymer.

Pater, R. H.↗
DOE OSTI2022

Impacts of phase state and water content on secondary organic aerosol formation and partitioning (Final Technical Report)

Secondary organic aerosols (SOA) account for a major fraction of particulate matter in the atmosphere, affecting climate, air quality, and public health. SOA formation and evolution are highly complex processes involving both chemical reactions and transport of molecules in air, at particle surfaces, and within particles. The state of the matter, or “phase state,” comprising SOA can vary from a liquid, over an amorphous semi-solid, to a glassy solid, depending on chemical composition, water content, relative humidity (RH), and temperature. The occurrence of glassy and amorphous semi-solid states can pose limitations on the rate of transport of molecules, affecting gas-particle interactions and challenging the treatment of SOA in atmospheric models. The objective of this project was to improve fundamental understanding of the interplay of the phase state of particles and water content on the evolution of SOA formation. We have developed a method to estimate the glass transition temperature (T g ) of organic compounds to predict the phase state and viscosity of SOA. This method has been applied to high resolution mass spectrometry data of various types of SOA, achieving a good agreement with viscosity measurements. In addition, the viscosity estimation method was implemented into a regional model CMAQ to simulate diel and seasonal variations of SOA phase state over the U.S. Applying kinetic multilayer modeling, we analyzed laboratory experiments and ARM field measurements (e.g., HI-SCALE) on kinetic limitations of amine uptake. We have also conducted numerical simulations to estimate equilibration timescales of SOA partitioning. Overall, we have evaluated the impacts of phase state and water content on SOA lifecycle that should contribute to reducing the uncertainty of SOA representation in regional climate and air quality predictions. The project has yielded 17 publications, in which DE-SC0018349 is explicitly acknowledged. Please see the list of publications as below, followed by summary of research activities.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1986

On the location of the maximum homogeneous crystal nucleation temperature

Detailed considerations are given to the location of the temperature of maximum homogeneous nucleation as predicted by classical nucleation theory. It is shown quite generally that this maximum temperature, T-asterisk, must occur above the Kauzmann temperature and that the T-asterisk is such that T-asterisk is greater than T(m)/3, where T(m) is the melting temperature. Also, it is demonstrated tha T-asterisk may be considered to be approximately dependent upon two parameters: gamma, the ratio of the difference in specific heat between the crystal and liquid divided by the entropy of fusion, and E, a reduced activation energy for viscous flow. The variation of T-asterisk with these parameters is described. The relationship of the relative location of T-asterisk to the glass transition temperature, is discussed too. This discussion is couched within the framework of the strong and fragile liquid notion introduced by Angell (1981) and coworkers. Finally, the question of the ultimate limits to the undercooling of liquid metals is considered and its relationhsip to computations of the maximum nucleation temperature in such systems.

Weinberg, Michael C.↗
NASA NTRS1980

The accelerated characterization of viscoelastic composite materials

Necessary fundamentals relative to composite materials and viscoelasticity are reviewed. The accelerated characterization techniques of time temperature superposition and time temperature stress superposition are described. An experimental procedure for applying the latter to composites is given along with results obtained on a particular T300/934 graphite/epoxy. The accelerated characterization predictions are found in good agreement with actual long term tests. A postcuring phenomenon is discussed that necessitates thermal conditioning of the specimen prior to testing. A closely related phenomenon of physical aging is described as well as the effect of each on the glass transition temperature and strength. Creep rupture results are provided for a variety of geometries and temperatures for T300/934 graphite/epoxy. The results are found to compare reasonably with a modified kinetic rate theory.

Griffith, W. I.↗
NASA NTRS2002

Viscoelastic and Mechanical Properties of Thermoset PMR-type Polyimide-Clay Nanocomposites

High temperature thermoset polyimide-clay nanocomposites were prepared by blending 2.5 and 5 wt% of an unmodified Na(+-) montmorillonite (PGV) and two organically modified FGV (PGVCl0COOH, PGVC12) with a methanol solution of PMR-15 precursor. The methanol facilitated the dispersal of the unmodified clay. Dynamic mechanical analysis results showed a significant increase in the thermomechanical properties (E' and E") of 2.5 wt% clay loaded nanocomposites in comparison with the neat polyimide. Higher glass transition temperatures were observed for 2.5 wt% nanocomposites compared to the neat polyimide. Flexural properties measurements for the 2.5 wt% nanocomposites showed a significant improvement in the modulus and strength, with no loss in elongation. This trend was not observed for the 5 wt% nanocomposites. An improvement in the CTE was observed for the PGV/PMR-15 nanocomposites, while a decrease was observed for the organically modified samples. This was attributed to potential variations in the interface caused by modifier degradation.

Abdalla, Mohamed O.↗
NASA NTRS2012

Solvent free low-melt viscosity imide oligomers and thermosetting polymide composites

.[.This invention relates to the composition and a solvent-free process for preparing novel imide oligomers and polymers specifically formulated with effective amounts of a dianhydride such as 2,3,3',4-biphenyltetra carboxylic dianydride (a-BPDA), at least one aromatic diamine and an endcapped of 4-phenylethynylphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260-280.degree. C. When the imide oligomer melt is cured at about 371.degree. C. in a press or autoclave under 100-500 psi, the melt resulted in a thermoset polyimide having a glass transition temperature (T.sub.g) equal to and above 310.degree. C. A novel feature of this process is that the monomers; namely the dianhydrides, diamines and the endcaps, are melt processable to form imide oligomers at temperatures ranging between 232-280.degree. C. (450-535.degree. F.) without any solvent. These low-melt imide oligomers can be easily processed by resin transfer molding (RTM), vacuum-assisted resin transfer molding (VARTM) or the resin infusion process with fiber preforms e.g. carbon, glass or quartz preforms to produce polyimide matrix composites with 288-343.degree. C. (550-650.degree. F.) high temperature performance capability..]. .Iadd.This invention relates to compositions and a solvent-free reaction process for preparing imide oligomers and polymers specifically derived from effective amounts of dianhydrides such as 2,3,3',4'-biphenyltetracarboxylic dianhydride (a-BPDA), at least one aromatic polyamine and an end-cap such as 4-phenylethynyphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260.degree. C.-280.degree. C..Iaddend.

Chuang, Chun-Hua↗
DOE OSTI2021

Processing Effects on the Self-Assembly of Brush Block Polymer Photonic Crystals

Here,the self-assembly of poly(dimethylsiloxane)-b-poly(trimethylene carbonate) (PDMS-b-PTMC) bottlebrush block polymers was investigated under different processing conditions. Small-angle X-ray scattering (SAXS) and UV/Visible spectroscopy provided insight into the self-assembly and structure in response to heating and applied pressure. In the absence of applied pressure (i.e., before annealing), the PDMS-b-PTMC bottlebrush block polymers are white solids and adopt small, randomly oriented lamellar grains. Heating the materials to 140 °C in the absence of applied pressure appears to “lock in” the isotropic, short-range-ordered state, preventing the formation of the long-range-ordered lamellar structure responsible for photonic properties. Applying modest anisotropic pressure (3 psi) between parallel plates at ambient temperature orients the short-range lamellar grains; however, applied pressure alone does not produce long-range order. Only when the bottlebrush block polymers were heated (>100 °C) under modest pressure (3 psi) were long-range-ordered photonic crystals formed. Analysis of the SAXS data motivated analogies to liquid crystals and revealed the potential self-assembly pathway. These results provide insight into the structure and self-assembly of bottlebrush block polymers with low glass transition temperature side chains in response to different processing conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2006

Solvent Free Low-Melt Viscosity Imide Oligomers And Thermosetting Polyimide Composites

This invention relates to the composition and a solvent-free process for preparing novel imide oligomers and polymers specifically formulated with effective amounts of a dianhydride such as 2,3,3',4-biphenyltetra carboxylic dianydride (a-BPDA), at least one aromatic diamine' and an endcapped of 4-phenylethynylphthalic anhydride (PEPA) or nadic anhydride to produce imide oligomers that possess a low-melt viscosity of 1-60 poise at 260-280" C. When the imide oligomer melt is cured at about 371 C. in a press or autoclave under 100-500 psi, the melt resulted in a thermoset polyimide having a glass transition temperature (T(sub g)) equal to and above 310 C. A novel feature of this process is that the monomers; namely the dianhydrides, diamines and the endcaps, are melt processable to form imide oligomers at temperatures ranging between 232-280 C. (450-535 F) without any solvent. These low-melt imide oligomers can be easily processed by resin transfer molding (RTM), vacuum-assisted resin transfer molding (VARTM) or the resin infusion process with fiber preforms e.g. carbon, glass or quartz preforms to produce polyimide matrix composites with 288-343C (550-650 F) high temperature performance capability.

Chuang, CHun-Hua↗
NASA NTRS1997

Structure-Property Relationships of Bismaleimides

The purpose of this research was to control and systematically vary the network topology of bismaleimides through cure temperature and chemistry (addition of various coreactants) and subsequently attempt to determine structure-mechanical property relationships. Characterization of the bismaleimide structures by dielectric, rheological, and thermal analyses, and density measurements was subsequently correlated with mechanical properties such as modulus, yield strength, fracture energy, and stress relaxation. The model material used in this investigation was 4,4'-BismaleiMidodIphenyl methane (BMI). BMI was coreacted with either 4,4'-Methylene Dianiline (MDA), o,o'-diallyl bisphenol A (DABA) from Ciba Geigy, or Diamino Diphenyl Sulfone (DDS). Three cure paths were employed: a low- temperature cure of 140 C where chain extension should predominate, a high-temperature cure of 220 C where both chain extension and crosslinking should occur simultaneously, and a low-temperature (140 C) cure followed immediately by a high-temperature (220 C) cure where the chain extension reaction or amine addition precedes BMI homopolymerization or crosslinking. Samples of cured and postcured PMR-15 were also tested to determine the effects of postcuring on the mechanical properties. The low-temperature cure condition of BMI/MDA exhibited the highest modulus values for a given mole fraction of BMI with the modulus decreasing with decreasing concentration of BMI. The higher elastic modulus is the result of steric hindrance by unreacted BMI molecules in the glassy state. The moduli values for the high- and low/high-temperature cure conditions of BMI/MDA decreased as the amount of diamine increased. All the moduli values mimic the yield strength and density trends. For the high-temperature cure condition, the room- temperature modulus remained constant with decreasing mole fraction of BMT for the BMI/DABA and BMI/DDS systems. Postcuring PMR-15 increases the modulus over that of the cured material even though density values of cured and postcured PMR were essentially the same. Preliminary results of a continuous and intermittent stress relaxation experiment for BMI:MDA in a 2:1 molar ratio indicate that crosslinking is occurring when the sample is in the undeformed state. Computer simulation of properties such as density, glass transition temperature, and modulus for the low- temperature cure conditions of BMI/MDA and BMI/DABA were completed. The computer modeling was used to help further understand and confirm the structure characterization results. The simulations correctly predicted the trends of these properties versus mole fraction BMI and were extended to other BMI/diamine systems.

Tenteris-Noebe, Anita D.↗
DOE OSTI2023

High-temperature low-humidity proton exchange membrane with “stream-reservoir” ionic channels for high-power-density fuel cells

The perfluorosulfonic acid (PFSA) proton exchange membrane (PEM) is the key component for hydrogen fuel cells (FCs). We used in situ synchrotron scattering to investigate the PEM morphology evolution and found a “stream-reservoir” morphology, which enables efficient proton transport. The short-side-chain (SSC) PFSA PEM is fabricated under the guidance of morphology optimization, which delivered a proton conductivity of 193 milliSiemens per centimeter [95% relativity humidity (RH)] and 40 milliSiemens per centimeter (40% RH) at 80°C. The improved glass transition temperature, water permeability, and mechanical strength enable high-temperature low-humidity FC applications. Performance improvement by 82.3% at 110°C and 25% RH is obtained for SSC-PFSA PEM FCs compared to Nafion polymer PEM devices. The insights in chain conformation, packing mechanism, crystallization, and phase separation of PFSAs build up the structure-property relationship. In addition, SSC-PFSA PEM is ideal for high-temperature low-humidity FCs that are needed urgently for high-power-density and heavy-duty applications.

25 ENERGY STORAGE↗
DOE OSTI2023

Atomistic Simulations of Polydisperse Lignin Melts Using Simple Polydisperse Residue Input Generator

Understanding the physics of lignin will help rationalize its function in plant cell walls as well as aiding practical applications such as deriving biofuels and bioproducts. Here, in this work, we present SPRIG (Simple Polydisperse Residue Input Generator), a program for generating atomic-detail models of random polydisperse lignin copolymer melts i.e., the state most commonly found in nature. Using these models, we use all-atom molecular dynamics (MD) simulations to investigate the conformational and dynamic properties of polydisperse melts representative of switchgrass (Panicum virgatum L.) lignin. Polydispersity, branching and monolignol sequence are found to not affect the calculated glass transition temperature, T g . The Flory–Huggins scaling parameter for the segmental radius of gyration is 0.42 ± 0.02, indicating that the chains exhibit statistics that lie between a globular chain and an ideal Gaussian chain. Below T g the atomic mean squared displacements are independent of molecular weight. In contrast, above T g , they decrease with increasing molecular weight. Therefore, a monodisperse lignin melt is a good approximation to this polydisperse lignin when only static properties are probed, whereas the molecular weight distribution needs to be considered while analyzing lignin dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗