Results for “framing camera” — Page 19

NASA NTRS1990

Instrumentation and robotic image processing using top-down model control

A top-down image processing scheme is described. A three-dimensional model of a robotic working environment, with robot manipulators, workpieces, cameras, and on-the-scene visual enhancements is employed to control and direct the image processing, so that rapid, robust algorithms act in an efficient manner to continually update the model. Only the model parameters are communicated, so that savings in bandwidth are achieved. This image compression by modeling is especially important for control of space telerobotics. The background for this scheme lies in an hypothesis of human vision put forward by the senior author and colleagues almost 20 years ago - the Scanpath Theory. Evidence was obtained that repetitive sequences of saccadic eye movements, the scanpath, acted as the checking phase of visual pattern recognition. Further evidence was obtained that the scanpaths were apparently generated by a cognitive model and not directly by the visual image. This top-down theory of human vision was generalized in some sense to the frame in artificial intelligence. Another source of the concept arose from bioengineering instrumentation for measuring the pupil and eye movements with infrared video cameras and special-purpose hardware.

Stark, Lawrence↗

NASA NTRS1968

Technique increases storage capacity in camera tube target

Technique increases the signal current, where direct beam readout is used, in Secondary Electron Conduction /SEC/ camera tubes. Increasing the storage capacity and therefore the dynamic range of the SEC target permits satisfactory operation at reduced frame rates.

Boll, K. F.↗

NASA NTRS2000

Aeroelastic Deformation Measurements of Flap, Gap, and Overhang on a Semispan Model

Single-camera, single-view videogrammetry has been used to determine static aeroelastic deformation of a slotted flap configuration on a semispan model at the National Transonic Facility (NTF). Deformation was determined by comparing wind-off to wind-on spatial data from targets placed on the main element, shroud, and flap of the model. Digitized video images from a camera were recorded and processed to automatically determine target image plane locations that were then corrected for sensor, lens, and frame grabber spatial errors. The videogrammetric technique has been established at NASA facilities as the technique of choice when high-volume static aeroelastic data with minimum impact on data taking is required. The primary measurement at the NTF with this technique in the past has been the measurement of static aeroelastic wing twist on full span models. The first results using the videogrammetric technique for the measurement of component deformation during semispan testing at the NTF are presented.

Burner, A. W.↗

NASA NTRS2001

Dynamic Deformation Measurements of an Aeroelastic Semispan Model

The techniques used to acquire, reduce, and analyze dynamic deformation measurements of an aeroelastic semispan wind tunnel model are presented. Single-camera, single-view video photogrammetry (also referred to as videogrammetric model deformation, or VMD) was used to determine dynamic aeroelastic deformation of the semispan 'Models for Aeroelastic Validation Research Involving Computation' (MAVRIC) model in the Transonic Dynamics Tunnel at the NASA Langley Research Center. Dynamic deformation was determined from optical retroreflective tape targets at five semispan locations located on the wing from the root to the tip. Digitized video images from a charge coupled device (CCD) camera were recorded and processed to automatically determine target image plane locations that were then corrected for sensor, lens, and frame grabber spatial errors. Videogrammetric dynamic data were acquired at a 60-Hz rate for time records of up to 6 seconds during portions of this flutter/Limit Cycle Oscillation (LCO) test at Mach numbers from 0.3 to 0.96. Spectral analysis of the deformation data is used to identify dominant frequencies in the wing motion. The dynamic data will be used to separate aerodynamic and structural effects and to provide time history deflection data for Computational Aeroelasticity code evaluation and validation.

Graves, Sharon S.↗

NASA NTRS2001

Aeroelastic Deformation Measurements of Flap, Gap, and Overhang on a Semispan Model

Single-camera, single-view videogrammetry has been used for the first time to determine static aeroelastic deformation of a slotted flap configuration on a semispan model at the National Transonic Facility (NTF). Deformation was determined by comparing wind-off to wind-on spatial data from targets placed on the main element, shroud, and flap of the model. Digitized video images from a camera were recorded and processed to automatically determine target image plane locations that were then corrected for sensor, lens, and frame grabber spatial errors. The videogrammetric technique used for the measurements presented here has been established at NASA facilities as the technique of choice when high-volume static aeroelastic data with minimum impact on data taking is required. However, the primary measurement at the NTF with this technique in the past has been the measurement of the static aeroelastic wing twist of the main wing element on full span models rather than for the measurement of component deformation. Considerations for using the videogrammetric technique for semispan component deformation measurements as well as representative results are presented.

Burner, A. W.↗

NASA NTRSDate not supplied

Measurement of material recession and shock standoff in plasma windtunnel using neural nets

Arcjets are plasma wind tunnels used to test the performance of heatshield materials for spacecraft atmospheric entry. These facilities present an extremely harsh flow environment with heat fluxes up to 10^9 W/m^2 for up to 30 minutes. The plasma is low-temperature (~1 eV) but high pressure (> 10 kPa) creating high-enthalpy supersonic flows similar to atmospheric entry conditions. Typically, material samples are measured before and after a test to characterize the total recession. However, this does not capture time-dependent effects such as material expansion and non-linear recession. This work will present new analysis of arcjet test videos which measure both the time-dependent 2D recession of the material samples and the shock standoff distance. New results showing non-linear material erosion rates will be highlighted. The material and shock edges are extracted from the videos by training and applying a convolutional neural network. Due to the consistent camera settings, the machine learning model achieves high accuracy (~99%) on new data with only a small number of training frames (~80). The new results will be discussed in the context of temperature dependent plasma-surface interaction.

Magnus A Haw↗

NASA NTRSDate not supplied

Towards An Autonomous sUAS Operating in UTM TCL4+ and STEReO Fire Scenario

This study presents two sUAS payload point designs for enabling autonomous BVLOS flight in UTM TCL4+ urban environments and STEReO fire responses. The payload components for the first payload include an onboard computer and a 360 LIDAR. The second payload, which is a continuation of the first, adds a range finder altimeter, downward-facing monocular camera, forward-facing thermal and visible light dual camera, vehicle-to-vehicle radio modem, and Li-ion smart battery. The components are mounted on enclosed structural frames that were designed in-house. Placing the autonomy components onboard leverages the advantages of sUAS over manned aircraft such as low-cost, quick response time, and increased scalability. Autonomous capabilities include embedded processing, SLAM, object and fire detection, and V2V communication. Data processing is conducted onboard the aircraft to eliminate the dependency on a groundstation downlink. The first iteration of the payload is tested in both simulation and flight tests while the continuing iteration is in development.

Autonomous UAS↗

NASA NTRS1997

Experimental Investigation of a Graphite-Composite Intertank Section for a Reusable Launch Vehicle

The use of graphite-composites as primary structure is essential for the development of a cost effective single-stage-to-orbit reusable launch vehicle (RLV). A full-scale segment of a graphite-composite intertank was designed and fabricated by an industry team and tested at NASA Langley Research Center as a part of the RLV technology development program. The intertank test component was approximately 3.0 m long by 6.7 m wide and included slightly less than a 90deg section of a cylindrical intertank. The test article was fabricated using graphite-bismaelimide composite material and consisted of a hat-stiffened skin with five ring frames. The stiffeners were secondarily bonded to the panel skin and the ring frames were mechanically attached. The test article was loaded to failure with a uniform compression load applied by 21 individually controlled hydraulic actuators. Resistance strain gages, linear variable differential transformers and video cameras were used to measure and record the test results. A linear f d t e element analysis of the test article and test fixture was performed. The test results verified the structural integrity cf the intertank test article up to the design limit load. However, the test article failed in general skin buckling between the ring frames at a load 1.08 times design limit load. This load was considerably lower than the expected failure load. The cause of premature failure is being investigated. Good correlation of the test and analysis results was obtained for loads up to the design limit load.

Sawyer, James Wayne↗

NASA NTRS2000

Astrometry of the omega Centauri Hubble Space Telescope Calibration Field

Astrometry, on the International Celestial Reference Frame (epoch J2000.0), is presented for the Walker (1994, PASP, 106, 828) stars in the omega Centauri (=NGC 5139=C 1323-1472) Hubble Space Telescope Wide Field/Planetary Camera (WF/PC) calibration field of Harris et al. (1993, AJ, 105, 1196). Harris et al. stars were first identified on a WFPC2 observation of the omega Cen HST calibration field. Relative astrometry of the Walker stars in this field was then obtained using Walker's CCD positions and astrometry derived using the STSDAS METRIC task on the positions of the Harris et al. stars on the WFPC2 observation. Finally, the relative astrometry, which was based on the HST Guide Star Catalog, is placed on the International Celestial Reference Frame with astrometry from the USNO-A2.0 catalog. An ASCII text version of the astrometric data of the Walker stars in the omega Cen HST calibration field is available electronically in the online version of the article.

Mighell, Kenneth J.↗

NASA NTRS2005

Camera Image Transformation and Registration for Safe Spacecraft Landing and Hazard Avoidance

Inherent geographical hazards of Martian terrain may impede a safe landing for science exploration spacecraft. Surface visualization software for hazard detection and avoidance may accordingly be applied in vehicles such as the Mars Exploration Rover (MER) to induce an autonomous and intelligent descent upon entering the planetary atmosphere. The focus of this project is to develop an image transformation algorithm for coordinate system matching between consecutive frames of terrain imagery taken throughout descent. The methodology involves integrating computer vision and graphics techniques, including affine transformation and projective geometry of an object, with the intrinsic parameters governing spacecraft dynamic motion and camera calibration.

Jones, Brandon M.↗

NASA NTRS1987

Fiducial reference for the HIPPARCOS reference system

The groundwork was prepared for observations by the Hubble Space Telescope (HST) to tie the coordinate system of the European Astrometry Satellite HIPPARCOS to an extragalactic (VLBI) reference frame, and to determine the rotation of the HIPPARCOS frame with respect to the extragalactic frame. A total of 90 Extragalactic Optical Objects (EGOs) were determined in the vicinity (angular separation less than 18 arcminutes) of 160 HIPPARCOS stars (brighter than about 11.0 magnitude, mostly SAO stars brighter than 10.5), evenly distributed over the sky, to be used to tie the HIPPARCOS system to the Extragalactic Reference Frame. The pairs are to be observed with the HST Fine Guidance Sensors (FGS), sometimes in conjunction with the HST Planetary Camera, in order to determine the relative positions and motions of the individual HIPPARCOS stars with respect to the EGOs. The data base which contains the optical information used to generate the HST Guaranteed Observing Time (GTO) proposal is included.

Duncombe, R. L.↗

NASA NTRS1993

Targeting an asteroid - The Galileo spacecraft's encounter with 951 Gaspra

On 1991 October 29, the Galileo spacecraft provided the first in situ observations of an asteroid. To a significant degree, the successful encounter with asteroid 951 Gaspra was made possible by the high accuracy of the ground-based Gaspra ephemeris and the refinement to this initial ephemeris provided by the use of optical navigation images taken on board the spacecraft itself. The success of these celestial navigation efforts was dramatically demonstrated when Gaspra appeared in the central frame of the large mosaic of CCD images-less than one asteroid diameter from Gaspra's expected location in the camera's field of view. The corrections to Gaspra's ground-based ephemeris, based upon the optical on-board navigation images, were less than 80 km. The ground-based observation program that went into this ephemeris development is discussed and the accuracy of the ephemeris is used to validate the assumptions that went into the error analysis studies.

Yeomans, D. K.↗

NASA NTRSDate not supplied

An Autonomous sUAS Operating in UTM TCL4+ and STEReO Fire Scenario

This study presents a sUAS payload point design that enables autonomous BVLOS flightin UTM TCL4+ urban environments and STEReO fire responses. The payload components include an onboard computer, 360 deg LIDAR, range finder altimeter, downward-facing monocular camera, forward-facing thermal and visible light dual camera, vehicle-to-vehicle radio modem, and Li-ion smart battery. The components are mounted on an enclosed structural frame that was designed in-house. Placing the autonomy components onboard leverages the advantages of sUAS over manned aircraft such as low-cost, quick response time, and increased scalability. Autonomous capabilities include object and fire detection, V2V communication, embedded processing, and SLAM. Data processing is conducted on-board the aircraft to eliminate the dependency on a ground station downlink. The payload is evaluated in both software simulation as well as flight tests.

Autonomous UAS↗

NASA NTRS2015

Results of Microgravity Fluid Dynamics Captured With the Spheres-Slosh Experiment

This paper provides an overview of the SPHERES-Slosh Experiment (SSE) aboard the International Space Station (ISS) and presents on-orbit results with data analysis. In order to predict the location of the liquid propellant during all times of a spacecraft mission, engineers and mission analysts utilize Computational Fluid Dynamics (CFD). These state-of-the-art computer programs numerically solve the fluid flow equations to predict the location of the fluid at any point in time during different spacecraft maneuvers. The models and equations used by these programs have been extensively validated on the ground, but long duration data has never been acquired in a microgravity environment. The SSE aboard the ISS is designed to acquire this type of data, used by engineers on earth to validate and improve the CFD prediction models, improving the design of the next generation of space vehicles as well as the safety of current missions. The experiment makes use of two Synchronized Position Hold, Engage, Reorient Experimental Satellites (SPHERES) connected by a frame. In the center of the frame there is a plastic, pill shaped tank that is partially filled with green-colored water. A pair of high resolution cameras records the movement of the liquid inside the tank as the experiment maneuvers within the Japanese Experimental Module test volume. Inertial measurement units record the accelerations and rotations of the tank, making the combination of stereo imaging and inertial data the inputs for CFD model validation.

slosh↗

NASA NTRS2015

Results of Microgravity Fluid Dynamics Captured with the Spheres-Slosh Experiment

This paper provides an overview of the SPHERES-Slosh Experiment (SSE) aboard the International Space Station (ISS) and presents on-orbit results with data analysis. In order to predict the location of the liquid propellant during all times of a spacecraft mission, engineers and mission analysts utilize Computational Fluid Dynamics (CFD). These state-of-the-art computer programs numerically solve the fluid flow equations to predict the location of the fluid at any point in time during different spacecraft maneuvers. The models and equations used by these programs have been extensively validated on the ground, but long duration data has never been acquired in a microgravity environment. The SSE aboard the ISS is designed to acquire this type of data, used by engineers on earth to validate and improve the CFD prediction models, improving the design of the next generation of space vehicles as well as the safety of current missions. The experiment makes use of two Synchronized Position Hold, Engage, Reorient Experimental Satellites (SPHERES) connected by a frame. In the center of the frame there is a plastic, pill shaped tank that is partially filled with green-colored water. A pair of high resolution cameras records the movement of the liquid inside the tank as the experiment maneuvers within the Japanese Experimental Module test volume. Inertial measurement units record the accelerations and rotations of the tank, making the combination of stereo imaging and inertial data the inputs for CFD model validation.

slosh↗

NASA NTRS2015

Result of Microgravity Fluid Dynamics Captured with the SPHERES-Slosh Experiment

This paper provides an overview of the SPHERES-Slosh Experiment (SSE) aboard the International Space Station (ISS) and presents on-orbit results with data analysis. In order to predict the location of the liquid propellant during all times of a spacecraft mission, engineers and mission analysts utilize Computational Fluid Dynamics (CFD). These state-of-the-art computer programs numerically solve the fluid flow equations to predict the location of the fluid at any point in time during different spacecraft maneuvers. The models and equations used by these programs have been extensively validated on the ground, but long duration data has never been acquired in a microgravity environment. The SSE aboard the ISS is designed to acquire this type of data, used by engineers on earth to validate and improve the CFD prediction models, improving the design of the next generation of space vehicles as well as the safety of current missions. The experiment makes use of two Synchronized Position Hold, Engage, Reorient Experimental Satellites (SPHERES) connected by a frame. In the center of the frame there is a plastic, pill shaped tank that is partially filled with green-colored water. A pair of high resolution cameras records the movement of the liquid inside the tank as the experiment maneuvers within the Japanese Experimental Module test volume. Inertial measurement units record the accelerations and rotations of the tank, making the combination of stereo imaging and inertial data the inputs for CFD model validation.

slosh↗

NASA NTRS2019

Air-To-Air Background Oriented Schlieren Technique

An air-to-air background-oriented Schlieren system and method for measuring and rendering visible density changes in air that cause a refractive index change by an airborne vehicle. A sensor aircraft equipped with a high-speed visible spectrum camera travels at low airspeed on a predetermined route and on a level altitude over a background having consistent contrast and sunlight reflectivity. The target aircraft, traveling on the same predetermined route but at an altitude between the sensor aircraft and the ground (background) passes beneath the sensor aircraft. The camera on the sensor aircraft captures a series of images including a reference image immediately before the target aircraft enters the image frame followed by several data images as the target aircraft passes through the image frame. The data images are processed to calculate density gradients around the target aircraft. These density gradients include shockwaves, vortices, engine exhaust, and wakes. Air density gradients cause a refractive index change in the fluid and a slight distortion in the background pattern of the data image. Image processing that compares the data image to the reference image yields the difference caused by the density gradient.

Heineck, James Thomas↗

NASA NTRS1971

The characterization of facsimile camera systems for lunar and planetary surface exploration

Advantages of facsimile camera systems are reviewed for imagery of lunar and planetary surfaces from stationary or stopped remotely controlled vehicles. They include: better geometric fidelity than television systems, more picture elements per frame, ability to take single frame panoramic pictures, a very high contrast ratio within a picture, a choice of one or more narrow-band spectral responses over a wide possible range, image transmission over a low bit-rate communications channel without storage, very low power, small size, low weight, and ruggedizability to meet space flight requirements. Systems of this kind are under development for the 1975 Viking Martian lander, and have been used by the Soviets on Lunas and Lunokhod laboratory and field evaluation of a completed facsimile camera system is presented. The applicability of facsimile cameras to lunar and planetary rovers is demonstrated.

Eisenman, A.↗