Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Effect of Key Parameters on the Photocatalytic Oxidation of Toluene at Low Concentrations in Air under 254 + 185 nm UV Irradiation

The effect of key experimental parameters on the removal of toluene under 254 + 185 nm irradiation was investigated using a benchtop photocatalytic flow reactor. Toluenewas introduced at low concentrations between 10 and 500 ppbv, typical of indoorenvironments, and reacted on TiO2-coated Raschig rings. Two different TiO2-coated rings were prepared: in one case, by dip-coating using a P25 aqueous suspension and, on the other, using an organic/inorganic sol-gel method that produced thin films of mesoporous anatase. Flow rates in the photoreactor varied between 4 L min-1 and 125 mL min-1, leading to residence times in the range 100 ms< tau< 2 s. For these conditions, toluene removal efficiencies were between 30 and 90percent, indicating that the system did not achieve total conversion in any case. For each air flow rate, the conversion oftoluene was significantly higher when the reactor length was 10 cm, as compared with 5 cm; however, only marginal increases in conversions were achieved in the two reactor lengths at equal residence time and different concentration of toluene, suggesting that that the reactor is effectively behaving as an ideal reactor and that the reaction is first-order in the concentration of toluene. Experiments were carried out between 0 and 66percent relative humidity (RH), the fastest reaction rate being observed at moderately low humidity conditions (10percent RH), with respect to both dry air and higher humidity levels. Formaldehyde was formed as a partial oxidation byproduct at low and at high residence times (240 and 960 ms), although higher formaldehyde molar yields (up to 20percent) were observed at low tau (240 ms) and moderate humidity conditions (10 and 33percent), suggesting that both tau and RH can be optimized toreduce the formation of harmful intermediates. Toluene removal efficiency increased with the TiO2 thickness (i.e., mass) until a maximum value of 500 nm, beyond which the removal efficiency decreased. This should be attributed to limitations on the rates of toluene decomposition imposed by radiation transport through the film and/or internal diffusion resistances, which can take place within the porous photocatalytic films.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Monodisperse Platinum and Rhodium Nanoparticles as Model Heterogeneous Catalysts

Model heterogeneous catalysts have been synthesized and studied to better understand how the surface structure of noble metal nanoparticles affects catalytic performance. In this project, monodisperse rhodium and platinum nanoparticles of controlled size and shape have been synthesized by solution phase polyol reduction, stabilized by polyvinylpyrrolidone (PVP). Model catalysts have been developed using these nanoparticles by two methods: synthesis of mesoporous silica (SBA-15) in the presence of nanoparticles (nanoparticle encapsulation, NE) to form a composite of metal nanoparticles supported on SBA-15 and by deposition of the particles onto a silicon wafer using Langmuir-Blodgett (LB) monolayer deposition. The particle shapes were analyzed by transmission electron microscopy (TEM) and high resolution TEM (HRTEM) and the sizes were determined by TEM, X-ray diffraction (XRD), and in the case of NE samples, room temperature H 2 and CO adsorption isotherms. Catalytic studies were carried out in homebuilt gas-phase reactors. For the nanoparticles supported on SBA-15, the catalysts are in powder form and were studied using the homebuilt systems as plug-flow reactors. In the case of nanoparticles deposited on silicon wafers, the same systems were operated as batch reactors. This dissertation has focused on the synthesis, characterization, and reaction studies of model noble metal heterogeneous catalysts. Careful control of particle size and shape has been accomplished though solution phase synthesis of Pt and Rh nanoparticles in order to elucidate further structure-reactivity relationships in noble metal catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Diffusion Limited Supercritical Water Oxidation (SCWO) in Microgravity Environments

Tests designed to quantify the gravitational effects on thermal mixing and reactant injection in a Supercritical Water Oxidation (SCWO) reactor have recently been performed in the Zero Gravity Facility (ZGF) at NASA s Glenn Research Center. An artificial waste stream, comprising aqueous mixtures of methanol, was pressurized to approximately 250 atm and then heated to 450 C. After uniform temperatures in the reactor were verified, a controlled injection of air was initiated through a specially designed injector to simulate diffusion limited reactions typical in most continuous flow reactors. Results from a thermal mapping of the reaction zone in both 1-g and 0-g environments are compared. Additionally, results of a numerical model of the test configuration are presented to illustrate first order effects on reactant mixing and thermal transport in the absence of gravity.

Hicks, M. C.↗

Two mechanisms for the spontaneous emergence, execution, and reprogramming of chemical logic circuits

A key question in origin-of-life research is how primitive life or life-like systems obtained reusable and reprogrammable machinery of processing information to respond to various environmental and internal stimuli. One strategy to approach this question is to view living systems as universal chemical computers. This approach focuses upon uncovering how reusable and reprogrammable chemical NOT, AND, and OR logic gates could appear under prebiotically possible scenarios where simple chemicals and second- or lower-order reactions are more frequent than macromolecules and higher-order reactions. In this article, we theoretically model two generic mechanisms of forming Boolean gates based on geochemically plausible reaction systems that could have preceded complex biopolymers. The mechanisms exploit simple bistable autocatalytic systems to encode binary variables and use heterogeneous dilution rates to differentially activate or deactivate autocatalysis in different reactors. We found that NOT, AND, and OR gates, as well as more complex logic circuits, can spontaneously arise from connected, well-mixed flow reactors based on (i) catalysis by a heterodimer between mutually inhibitory autocatalysts or (ii) selectively permeable tunnels connecting reactors. Our results suggest that simple machinery can support the prebiotic emergence of complex chemical logic circuits and provide new guides for experimentally actualizing chemical computation.

Zhen Peng↗

In-duct removal of mercury from coal-fired power plant flue gas by activated carbon: assessment of entrained flow versus wall surface contributions

In-duct mercury capture efficiency by activated carbon from coal-combustion flue gas was investigated. To this end, elemental mercury capture experiments were conducted at 100 C in a purposely designed 65-mm ID labscale pyrex apparatus operated as an entrained flow reactor. Gas residence times were varied between 0.7 and 2.0 s. Commercial-powdered activated carbon was continuously injected in the reactor and both mercury concentration and carbon elutriation rate were followed at the outlet. Transient mercury concentration profiles at the outlet showed that steady-state conditions were reached in a time interval of 15-20 min, much longer than the gas residence time in the reactor. Results indicate that the influence of the walls is non-negligible in determining the residence time of fine carbon particles in the adsorption zone, because of surface deposition and/or the establishment of a fluid-dynamic boundary layer near the walls. Total mercury capture efficiencies of 20-50% were obtained with carbon injection rates in the range 0.07-0.25 g/min. However, only a fraction of this capture was attributable to free-flowing carbon particles, a significant contribution coming from activated carbon staying near the reactor walls. Entrained bed experiments at lab-scale conditions are probably not properly representative of full-scale conditions, where the influence of wall interactions is lower. Moreover, previously reported entrained flow lab-scale mercury capture data should be reconsidered by taking into account the influence of particle-wall interactions.

01 COAL, LIGNITE, AND PEAT↗

Scaling the polymerization of polyaldehydes through continuous flow synthesis

Abstract A plug flow reactor was constructed to scale the synthesis of metastable, phthalaldehyde-based polymers to achieve production rates of 1–2 kg per day. The flow-induced mixing and in-line polymerization quench and precipitation sequences resulted in improved polymer purity and long-term stability compared to the same materials made from a conventional batch process. Cryogenic rheology was used to probe the complex fluid dynamics encountered during the polymerization of PPA homopolymers. It is envisioned that this continuous flow manufacturing approach could be extended to other low ceiling temperature or aldehyde monomer systems to help implement and support a plastic circular economy. Graphical abstract

Schwartz, Jared M.↗

A SUMMARY OF THE THEORETICAL BASIS OF THE RELAP-7 NUCLEAR REACTOR SYSTEM SAFETY ANALYSIS CODE

The RELAP-7 code is the next generation nuclear reactor system safety analysis code being developed at the Idaho National Laboratory (INL)[1]. The code is based on INL’s scientific software development framework, MOOSE (Multi-physics Object Oriented Simulation Environment)[2]. The primary basis of the RELAP-7 governing theory includes 7-equation two-phase flow, reactor core heat transfer, and reactor kinetics models. This paper will focus upon the compressible, fully nonequilibrium two-phase flow model.

7-equation two-phase model↗

Microkinetic Modeling of Lean NO x Trap Storage and Regeneration

A microkinetic chemical reaction mechanism capable of describing both the storage and regeneration processes in a fully formulated lean NOx trap (LNT) is presented. The mechanism includes steps occurring on the precious metal, barium oxide (NOx storage), and cerium oxide (oxygen storage) sites of the catalyst. The complete reaction set is used in conjunction with a transient plug flow reactor code (including boundary layer mass transfer) to simulate not only a set of long storage/regeneration cycles with a CO/H2 reductant, but also a series of steady flow temperature sweep experiments that were previously analyzed with just a precious metal mechanism and a steady state code neglecting mass transfer. The results show that, while mass transfer effects are generally minor, NOx storage is not negligible during some of the temperature ramps, necessitating a re-evaluation of the precious metal kinetic parameters. The parameters for the entire mechanism are inferred by finding the best overall fit to the complete set of experiments. Rigorous thermodynamic consistency is enforced for parallel reaction pathways and with respect to known data for all of the gas phase species involved. It is found that, with a few minor exceptions, all of the basic experimental observations can be reproduced with the transient simulations. In addition to accounting for normal cycling behavior, the final mechanism should provide a starting point for the description of further LNT phenomena such as desulfation and the role of alternative reductants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nonthermal plasma synthesis of silicon carbonitride

Abstract The use of a low‐temperature plasma for the synthesis of amorphous silicon carbonitride (SiCN) nanoparticles enables the realization of sintered bulk samples with high thermal stability. Amorphous SiCN nanoparticles are produced from a mixture of silane, methane, and ammonia utilizing a mid‐pressure, radio‐frequency, continuous flow reactor. Particle characterization shows that the nanoparticles are largely amorphous with some crystalline silicon and silicon carbide domains <10 nm in size. Compositional tuning, controlled by varying the precursor flow rates, coupled with the uniform mixing of elements at the nanoscale, results in samples that resist crystallization even when sintered at temperatures as high as 2000°C. This study suggests that the low‐temperature plasma synthesis of nanoparticles has great potential to produce bulk structural materials for application in harsh environments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Transient Pulse-Response Time-of-Flight Mass Spectrometry for Complex, Deactivating Heterogeneous Catalytic Systems: Application to Ethane Dehydroaromatization

The study of complex, multistep bond-forming and -breaking reactions in heterogeneous catalytic systems often encounters challenges associated with the involvement of large numbers of intermediates among branching pathways. Kinetic information obtained from traditional steady-state measurements can be complemented with that from time-resolved methods to uncover details of the underlying chemistry. Herein, we describe an approach for tracking the complete time-resolved chemical composition (ca. 4–200 u) of a reactor effluent in response to a reactant pulse. We use a six-port rotary valve with a metered sampling loop to pulse reactants at ambient pressure into a flow reactor packed with a catalyst bed within the isothermal region of a heated furnace. The temporal evolution of effluent species is tracked using time-resolved molecular-beam time-of-flight mass spectrometry. We highlight the possibilities that this method has to offer by studying the complex bifunctional mechanism of ethane dehydroaromatization over an HZSM-5-supported platinum catalyst. We demonstrate that energy-tunable ionization sources, which facilitate isomer resolution, enable the measurement of the full mass spectral time-dependent system response. This includes the evolution of major products and mechanistically relevant reactive intermediates such as 1,3-butadiene and cyclopentadiene; these species have not previously been observed from this reaction. In additional studies, we also assess the role of platinum in the catalyst by examining temporal responses to ethane and ethylene feeds. Results show that two temporally distinct formation pathways exist for methane and benzene, and that their importance depends on both catalyst composition and reactant identity. Additionally, characteristics of catalyst deactivation are uniquely observable in the time-resolved mass spectral response, including the selective deactivation of a benzene formation pathway. The combination of time-of-flight mass spectrometry with tunable ionization enables the simultaneous observation of all effluents in a complex mixture of intermediates with isomer/isobar differentiation capabilities that can be applied to any complex reaction system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Numerical simulation of non-Newtonian free shear flows

Free shear flows, like those of mixing layers, are encountered in aerodynamics, in the atmosphere, and in the ocean as well as in many industrial applications such as flow reactors or combustion chambers. It is, therefore, crucial to understand the mechanisms governing the process of transition to turbulence in order to predict and control the evolution of the flow. Delaying transition to turbulence as far downstream as possible allows a gain in energy expenditure while accelerating the transition can be of interest in processes where high mixing is desired. Various methods, including the use of polymer additives, can be effective in controlling fluid flows. The drag reduction obtained by the addition of small amounts of high polymers has been an active area of research for the last three decades. It is now widely believed that polymer additives can affect the stability of a large variety of flows and that dilute solutions of these polymers have been shown to produce drag reductions of over 80 percent in internal flows and over 60 percent in external flows under a wide range of conditions. The major thrust of this work is to study the effects of polymer additives on the stability of the incompressible mixing layer through large scale numerical simulations. In particular, we focus on the two dimensional flow and examine how the presence of viscoelasticity may affect the typical structures of the flow, namely roll-up and pairing of vortices.

Homsy, G. M.↗

Fluidized-bed and fixed-bed reactor testing of methane chemical looping combustion with MgO-promoted hematite

In this article MgO-promoted Fe 2 O 3 hematite oxygen carriers were synthesized from various Mg sources and evaluated for methane chemical looping combustion. Particles suitable for fluidized bed flow reactor studies were prepared in the lab. Cyclic CLC tests conducted in the fluidized bed with MgO promoted hematite showed better performance than that with hematite. Attrition resistance of laboratory prepared MgO promoted hematite was excellent. Reactivity and stability of the oxygen carrier materials were also tested in the thermogravimetric analyzer and bench-scale reactors. Scanning electron microscopy and energy-dispersive X-ray spectroscopy, and X-ray diffraction were used to study the morphology and elemental compositions present in the hematite and promoted hematite oxygen carriers prior to and following the multi-cycle chemical looping reaction. The incorporation of 5 wt% MgO led to an increased reaction rate and an increase in oxygen utilized as compared to the pure hematite oxygen carrier. Possible reasons for the promotion effect by MgO were evaluated. These studies reveal that the best performing oxygen carrier was the 5 wt% MgO/Fe 2 O 3 which exhibited no observed degradation in the kinetics and conversion performance in the methane step over 15 reduction and oxidation cycles. The Mg promoted oxygen carrier also showed reduced coke formation as compared to the pure hematite carrier.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A comprehensive experimental and kinetic modeling study of di-isobutylene isomers: Part 2

A wide variety of high temperature experimental data obtained in this study complement the data on the oxidation of the two di-isobutylene isomers presented in Part I and offers a basis for an extensive validation of the kinetic model developed in this study. Due to the increasing importance of unimolecular decomposition reactions in high-temperature combustion, we have investigated the di-isobutylene isomers in high dilution utilizing a pyrolysis microflow reactor and detected radical intermediates and stable products using vacuum ultraviolet (VUV) synchrotron radiation and photoelectron photoion coincidence (PEPICO) spectroscopy. Additional speciation data at oxidative conditions were also recorded utilizing a plug flow reactor at atmospheric pressure in the temperature range 725-1150 K at equivalence ratios of 1.0 and 3.0 and at residence times of 0.35 s and 0.22 s, respectively. Combustion products were analyzed using gas chromatography (GC) and mass spectrometry (MS). Ignition delay time measurements for di-isobutylene were performed at pressures of 15 and 30 bar at equivalence ratios of 0.5, 1.0, and 2.0 diluted in 'air' in the temperature range 900-1400 K using a high-pressure shock-tube facility. New measurements of the laminar burning velocities of di-isobutylene/air flames are also presented. The experiments were performed using the heat flux method at atmospheric pressure and initial temperatures of 298-358 K. Moreover, data consistency was assessed with the help of analysis of the temperature and pressure dependencies of laminar burning velocity measurements, which was interpreted using an empirical power-law expression. Electronic structure calculations were performed to compute the energy barriers to the formation of many of the product species formed. The predictions of the present mechanism were found to be in adequate agreement with the wide variety of experimental measurements performed.

09 BIOMASS FUELS↗

Condensed Phase Deactivation of Solid Brønsted Acids in the Dehydration of Fructose to Hydroxymethylfurfural

Catalyst deactivation resulting from the hydrothermal leaching of sulfonic acid residues and the deposition of carbonaceous residues was studied using condensed phase flow reactor experiments along with state-of-the-art solid-state NMR. Several commercially available sulfonic acid-containing heterogeneous Brønsted acids were compared by measuring the rates of sulfonic acid breakdown at hydrothermal flow conditions of 160 °C. Amberlyst 45 was found to show higher hydrothermal stability when compared to both Nafion and Amberlyst 15, with <10% loss in acidity after 48 h. The dehydration reaction of fructose to hydroxymethylfurfural (HMF) was used as a model system to compare deactivation rates from carbon deposition (fouling) to those from sulfur leaching, and deactivation from fouling was shown to be dramatically faster than that from sulfonic acid leaching alone. Fouling rates were then investigated in greater detail by comparing the influence of several factors including reactant, solvent, residence time, and feed concentration. The only successful approach to minimize fouling was the use of a polar aprotic solvent [dimethyl sulfoxide (DMSO)] with dilute (50 mM) reactant streams. In aqueous systems, operating the reactor in a regime with low conversion conditions (short residence times) does not significantly improve the longevity of the catalyst. Spent catalysts were characterized using 13C solid-state NMR spectroscopy enhanced by dynamic nuclear polarization. Additionally, in situ 1H and 13C high-resolution magic angle spinning (HR-MAS) solid-state NMR spectroscopies were used to investigate the solvent influence at the catalyst interface. The HR-MAS NMR studies showed that in polar aprotic solvents, the increased acidity leads to greater selectivity toward HMF; more importantly, that the dehydration products do not readily adhere to the surface in DMSO, in contrast to their behavior in water. The results demonstrate that more active and longer-lived acid catalysts could be obtained by tuning the solvent and surface polarity to allow for efficient desorption of products, thereby reducing the catalyst deactivation that occurs due to fouling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Sequential Cascade Electrocatalytic Conversion of Carbon Dioxide to C–C Coupled Products

Cascade catalytic processes perform multistep chemical transformations without isolating the intermediates. Here, we demonstrate a sequential cascade pathway to convert CO 2 to C 2+ hydrocarbons and oxygenates in a two-step electrocatalytic process using CO as the intermediate. CO 2 to CO conversion is performed by using Ag, and further conversion of CO to C-C coupled products is performed with Cu. Temporal separation between the two reaction steps is accomplished by situating the Ag electrode upstream of the Cu electrode in a continuous flow reactor. Convection-diffusion simulations and experimental evaluation of the electrodes individually are performed to identify optimal conditions. With the upstream Ag electrode poised at -1 V versus reversible hydrogen electrode in a flow of CO 2 -saturated water in aqueous carbonate buffer, over 80% of the CO can be converted on the downstream Cu electrode. When the Ag electrode is on, a supersaturation of CO is achieved near the Cu electrode, which leads to a relative increase in the formation rate of C 2 and C 3 oxygenates as compared to ethylene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of early-stage coal oxidation by temperature-programmed desorption

To obtain representative temperature-programmed desorption (TPD) profiles of young oxidized chars up to 1650{degree}C with minimal reactor wall interferences, the chemistry and physics of four ceramic materials has been critically reviewed. A two-staged experimental apparatus is then uniquely designed to produce chars in an Al{sub 2}O{sub 3} flow reactor with 1-21% O{sub 2} followed by in situ TPD with a SiC tube. Comparison of TPD profiles of oxidized chars with those from pyrolyzed chars and ashes suggests early-stage char oxidation is profoundly influenced by oxygen from three sources: organic oxygen, mineral matters, and gas phase O{sub 2}. Young chars oxidized at 1000{degree}C with less than 0.3 s residence time shows CO desorption peaks during TPD at three distinct temperatures: 730, 1280, and 1560{degree}C. The peaks at 730{degree}C are mainly caused by incomplete devolatilization. The peaks at 1280{degree}C mainly represent desorption of stable surface oxides and incomplete devolatilization. Increasing the gas phase oxidants notably increases the amount of stable surface oxides. The broad peaks between 1400 and 1650{degree}C are attributed to the reactions of oxidants decomposed from minerals and carbon in the char or SiC tube. Gas-phase oxygen shifts these reactions to lower temperatures. Detailed oxygen balance based on the CO and CO{sub 2} yields and elemental compositions of both pyrolysis and oxidized chars reveals that oxygen uptakes are very high, +0.056 mg O per mg of carbon, in chars derived from bituminous coal, whereas lignite chars show negative oxygen uptake, -0.020 mg O per mg of carbon, in char. Indeed, lignite char seems to possess little amount of stable surface oxides other than those contributed by the minerals. The extensive emissions of CO from lignite chars during TPD seem to suggest that either O{sub 2} or minerals promotes the oxygen transfer on char surface and subsequent carbon oxidation. 85 refs., 5 figs., 4 tabs.

01 COAL, LIGNITE, AND PEAT↗

Hydrogen production by high-temperature steam gasification of biomass and coal

High-temperature steam gasification of paper, yellow pine woodchips, and Pittsburgh bituminous coal was investigated in a batch-type flow reactor at temperatures in the range of 700 to 1,200{sup o}C at two different ratios of steam to feedstock molar ratios. Hydrogen yield of 54.7% for paper, 60.2% for woodchips, and 57.8% for coal was achieved on a dry basis, with a steam flow rate of 6.3 g/min at steam temperature of 1,200{sup o}C. Yield of both the hydrogen and carbon monoxide increased while carbon dioxide and methane decreased with the increase in gasification temperature. A 10-fold reduction in tar residue was obtained at high-temperature steam gasification, compared to low temperatures. Steam and gasification temperature affects the composition of the syngas produced. Higher steam-to-feedstock molar ratio had negligible effect on the amount of hydrogen produced in the syngas in the fixed-batch type of reactor. Gasification temperature can be used to control the amounts of hydrogen or methane produced from the gasification process. This also provides mean to control the ratio of hydrogen to CO in the syngas, which can then be processed to produce liquid hydrocarbon fuel since the liquid fuel production requires an optimum ratio between hydrogen and CO. The syngas produced can be further processed to produce pure hydrogen. Biomass fuels are good source of renewable fuels to produce hydrogen or liquid fuels using controlled steam gasification.

01 COAL, LIGNITE, AND PEAT↗