Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fission product”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Atom probe tomography of segregation at grain boundaries and gas bubbles in neutron irradiated U-10 wt% Mo fuel

During neutron irradiation to fission densities > 5.2 × 10 21 fiss/cm 3 , Xe agglomerates forming gas bubbles of varying size within the U-Mo fuel matrix. Herein, segregation of fission products to Xe bubbles and grain boundaries (GB) were studied using atom probe tomography (APT). Segregation behavior was found to vary among GBs, small bubbles (<10 nm), and larger bubbles (>10 nm). Solid fission products were enriched at GBs and larger bubbles, but not at small bubbles. Finally, a denuded zone was identified adjacent to a > 10 nm Xe gas bubble and a GB.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Measurements of Short-Lived Isomers from Photofission as a Method of Active Interrogation for Special Nuclear Materials

Isomeric fission products, such as 134m Te (T 1/2 = 164 ns) and 136m Xe (T 1/2 = 2.95 μs), are proposed as a signature of special nuclear materials in active interrogation applications. To test this conjecture, monoenergetic 9, 11, and 13 MeV photons from the HIγS facility are used to induce fission of 235 U, 238 U, and 239 Pu targets. The de-excitation γ rays of the isomers are measured using time-gated spectroscopy with high-purity germanium detectors. The 134m Te and 136m Xe isomers are detected and identified by the energy and decay half-life of their characteristic γ-ray transitions. The ratio of yields for these two signature γ rays, corresponding to 134m Te/( 136m Xe + 136 I), is found to be strongly correlated with the identity of the fissioning nuclei. These results show that fission-product isomers may be used in active interrogation to detect and identify special nuclear materials, even providing information on the isotopic enrichment. In conclusion, the feasibility of an active interrogation scenario using a bremsstrahlung beam is discussed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

AGR-5/6/7 Final Release-to-Birth Ratio Data Analysis

AGR-5/6/7 is the last of a series of Advanced Gas Reactor (AGR) experiments conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) in support of development and qualification of tristructural isotropic (TRISO) low-enriched fuel for use in the high-temperature gas cooled reactor (HTGR). AGR configuration and irradiation conditions are based on prismatic HTGR technology that is distinguished primarily through the use of helium coolant, a low-power-density ceramic core capable of withstanding very high temperatures, and TRISO-coated particle fuel. The AGR tests provide valuable irradiation-performance data to support fuel process development, qualify fuel for normal operation and accident conditions, and support development and validation of fuel performance and fission-product (FP) transport models and codes. Each AGR test consists of multiple independently controlled and monitored capsules containing fuel compacts placed in a graphite cylinder shrouded by a steel shell. Release-to-birth ratios (R/B) for fission-gas isotopes released from each capsule are calculated from release rates, measured by germanium detectors in the Fission Product Monitoring System (FPMS) installed downstream from each capsule, and birth rates calculated using numerical models of FG generation. The R/Bs are a critical measure of the ability of the fuel kernel, the particle coating layers, and the compact matrix to retain fission-gas atoms, preventing their release into the sweep-gas flow, and the impact of initially defective particles and/or particle-coating failures that occur during irradiation. For fission-gas isotopes, particle failure is defined as failure of all coating layers, allowing gaseous fission atoms to escape from a particle. During the first five cycles (162B ? 165A), R/Bs were stable in the 10-8?10-6 range, and no in-pile particle failures were observed, based on the gross gamma counts. The maximum R/B value of around 2 ? 10-6 for Kr-85m resulted from the presence of as-fabricated exposed kernels (based on the high exposed kernel fraction), the dispersed uranium, and high fuel particle temperatures in Capsule 1. Comparison of capsule-measured R/Bs from these early cycles to predictions using the previously developed AGR R/B model demonstrated FG release from the AGR-5/6/7 TRISO fuel was comparable to that of previous experiments. In addition, the Kr-85m R/B per-exposed-kernel values are comparable to R/B values obtained in AGR-3/4 irradiation experiment and four irradiation experiments performed during 1980s: (1) HRB-17/18, (2) COMEDIE-BD1, (3) HFR B1, and (4) HRB-21. In contrast, all measured R/B values are lower than predictions by the commonly used Richards and German models, which are intentionally conservative. A large number of in-pile particle failures occurred in Capsule 1 by the end of Cycle 166A. During the final four cycles (166A ? 168A), apparent damage to the Capsule 1 gas line appeared to cause FG leakage from that capsule into the other four capsules, resulting in an increase in fission gas (FG) detected in the effluent for all capsules. Isolation of the Capsule 1 gas line during the last three cycles also prevented measurement of its FG release. Thus, R/Bs in all capsules after Cycle 166A are highly uncertain because of undefined amount of leakage from Capsule 1, especially for long-lived isotopes. A few hundred in-pile particle failures were estimated for Capsule 1 before the end of Cycle 166A, but the total number of failures is unknown due to the lack of FG release data in the later cycles. Based primarily on evidence from the gross gamma counts during Cycle 168A, approximately 15 particles failed in Capsule 3 and four particles failed in Capsule 2. In-pile failures in Capsule 3 were anticipated because this capsule was designed to operate beyond the HTGR normal operating temperature range. In contrast, no in-pile failures were identified in the top two capsules (4 and 5) based on the absence of the typical spikes in gross gamma counts and low failure estimates using the AGR model, developed in INL/EXT-14-32970, for R/B of the short-lived isotopes (Kr-89 and Xe-137) with minimal leakage from Capsule 1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

The complex structural and chemical nature of monolithic U-10Mo fuel and Zr barrier layer

Nanoscale microstructural characterization by advanced transmission electron microscopy techniques on a U-10Mo/Zr barrier layer monolithic fuel plate was performed to evaluate the microstructural evaluation after high burn-up. Gas bubble superlattice evolution, grain restructuring, and evolution of the Zr interaction layer is investigated through detailed electron microscopy characterization. The use of automated crystallographic orientation mapping to irradiated U-10Mo fuel highlights that the restructured ultra-fine grains are separated by high angle grain boundaries at a burn up of 4.42 × 10 21 fissions/cm 3 . Additionally, advanced chemical analysis and multi-variable statistical analysis shows spatial clustering of solid fission product precipitates. Finally, characterization of a newly observed porous nanocrystalline Zr region in the barrier layer is studied. Finally, this work provides insights into the grain subdivision and restructuring process while using advanced microscopy techniques to analyze fission products in neutron-irradiated U-10Mo fuel.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Protection of graphite from salt and gas permeation in molten salt reactors

The reactor core, moderator and reflectors of a thermal spectrum advanced molten salt reactor will constitute multi-tons of graphite. Porous reactor-grade graphite, if unprotected, can be permeated by molten salt depending on the infiltrating pressure differential and entrance diameters of accessible graphite pores. Salt and gas permeation of graphite can affect microstructural properties and radiation behavior but also facilitate diffusion, deposition and retention of fission products and tritium. Because of the significant void volume of nuclear graphite, fission products and tritium retention due to salt permeation necessitates seal coatings or pore impregnation to reduce open porosity. Alternatively, very fine-grained graphite grades with low Xe permeability are being developed. In this work, we survey the current technologies for mitigating salt and gas transport into graphite.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Comparative post-irradiation examination of high burnup U-19Pu-10Zr: Assessing steady-state irradiation behavior against historical and modeled fuel performance

Here, the development of next-generation sodium-cooled fast reactors necessitates comprehensive research on metallic fuels to maximize economic performance while ensuring safe operation. In this study, we investigated the steady-state irradiation behavior of two high burnup U-19Pu-10Zr fuel pins, DP-36 and DP-40, in preparation for planned safety testing. Post-irradiation examination (PIE) was performed to quantify fuel column elongation, regions of low-density at the top of the fuel column, pin deformation, fission product distribution, fractional fission gas release, microstructural evolution, and fuel constituent redistribution. Benchmarking against existing PIE data from U-19Pu-10Zr fuel pins irradiated in EBR-II revealed consistent patterns in fuel column elongation and cladding diametral strain. However, both pins exhibited longer low-density structures, and destructive examination of DP-36 revealed more complex constituent redistribution patterns compared to previously reported data for ternary fuel pins. The steady-state irradiation of both pins was also modeled using BISON. Comparisons of PIE results with modeled predictions showed overall agreement in fractional fission gas release but consistent overestimation of axial and radial swelling due to gaseous and solid swelling models. These findings underscore the critical importance of pre-test characterization on test and sibling pins to accurately capture steady-state fuel behavior ahead of transient testing, thus establishing a baseline for post-test comparison. Additionally, these analyses identified key data gaps that warrant further investigation to improve the understanding and prediction of fuel swelling, thereby enhancing the synergy between modeling and experimental efforts in supporting accident testing.

BISON↗
DOE OSTI2020

Self-assembly of solid nanoclusters in molybdenum under gas ion implantation

The self-assembly of defects in materials could create unique physical and chemical properties. In nuclear fuels, the formation of self-assembled fission products mitigates fission-gas-release and swelling. In this work, we report the formation of a solid nanocluster superlattice in molybdenum, an important constituent in metallic fuels, under krypton gas ion implantation. X-ray absorption near edge structure measurements coupled with density functional theory calculations show that the pressure of krypton nanoclusters in molybdenum is ~2 GPa and molecular dynamic simulations reveal that the krypton atoms are solid in the nanoclusters with a krypton-to-vacancy ratio of ~0.28 at 300 K.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Revision of Fission Yields Uncertainties in ENDF/B-VIII.0

The spontaneous and neutron-induced fission yield sublibraries in the Evaluated Nuclear Data Files (ENDF/B) contain cumulative and independent fission yield values for dozens of fissioning systems, and hundreds of fission products. In this work, we report on a correction step that was undertaken after observing anomalously large uncertainties for several end-of-chain fission products. A total of 17 cumulative fission yield uncertainties and the value of 2 independent yields were corrected as a result of this revision.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Novel Electrochemical Technique: Serial Open Circuit Potentiometry to Examine the Separability of Lanthanides in Molten Salts

The accumulation of lanthanide fission products in molten salts reduces the efficiency of pyroprocessing used nuclear fuel. Lanthanide fission products are notoriously difficult to separate due to their similar physical and electrical properties. We developed a novel electrochemical technique called serial open circuit potentiometry (SOCP) which allows us to delineate between metal deposition reactions with similar reduction potentials to great precision. SOCP has several advantages over traditional open circuit potentiometry including its ability to create 3D plots that describe all metal deposition reactions in a system. This information can be used to precisely determine equilibrium potentials of metal deposition reactions and quantify their error, determine nucleation potentials, and determine the nucleation and growth mechanism. In this work, we demonstrated the effectiveness of SOCP by studying molten salt mixtures containing CeCl3, GdCl3, and both CeCl3 and GdCl3 in LiCl-KCl eutectic.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this paper are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

Accident Tolerant Fuels↗
DOE OSTI2025

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this presentation are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Retention of radionuclides in sol–gel surrogate nuclear explosive debris

Sol–gel vitrification can be used to rapidly produce solid, vitreous materials to support nuclear forensics research. Here, this work investigates three sol–gel synthetic approaches’ ability to retain fission products within the glass as a function of drying temperature. Eight of the ten fission products studied were quantitatively retained (less than 5% losses) at temperatures up to 600 °C for glasses prepared using an acidic catalyst and at temperatures up to 300 °C for glasses prepared using a basic catalyst. Both systems show partial loss of ruthenium and complete loss of iodine at temperatures above 300 and 100 °C, respectively.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Post-irradiation Heating Tests of As-Irradiated AGR-3/4 TRISO Fuel Compacts

Four post-irradiation heating tests of fuel compacts from the U.S. Advanced Gas Reactor (AGR)-3/4 irradiation experiment were completed. In addition to tristructural isotropic (TRISO)-coated driver fuel, each compact contained designed-to-fail (DTF) particles with fuel kernels coated only in pyrocarbon so as to simulate exposed kernels. Tests at 1600/1700°C, 1400°C, and 1200°C were performed to measure fission product release as a function of time and temperature. Silver release was highest in the 1200°C test, supporting the observation that silver release rates are highest in the 1100–1300°C range. Compared to tests of AGR-1 compacts with no exposed kernels, the Cs-134 and Kr-85 releases were noticeably higher in AGR-3/4. The exposed kernels’ contributions to Eu and Sr release are inconclusive, due to the difficulty in distinguishing among the combined effects of higher irradiation temperatures in these particular AGR-3/4 compacts, the presence of the DTF particles, and the Fuel Accident Condition Simulator (FACS) test temperatures. These data can be used to make inferences about fission product retention in exposed kernels as a function of time and temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Efficient high-fidelity TRISO statistical failure analysis using Bison: Applications to AGR-2 irradiation testing

The ability of tri-structural isotropic (TRISO) fuel to contain fission products is largely dictated by the quality of the manufacturing process, since most of the fission product release is expected to occur due to coating layer failure in a small number of particles containing defects. The Bison fuel performance code has capabilities to predict failure in individual particles, accounting for the presence of defects, and to apply statistical analysis methods to compute the probability of failure in a set of fuel particles. Bison has recently undergone significant development both to improve its physical representations of fuel particle behavior and to improve the efficiency of its statistical failure calculations. Physical model improvements include new capabilities to account for the pressure generated by fission gases on inner pyrolytic carbon (IPyC) crack surfaces and to use local material coordinate orientation to accurately incorporate the anisotropy in the material properties in aspherical particles. To improve statistical modeling efficiency, a direct integration approach which involves directly integrating the failure probability function associated with statistically varying parameters has been developed. The direct integration approach is much more efficient than the Monte Carlo (MC) schemes commonly employed, and allows Bison to directly run high-dimensional fuel performance models, which improves the accuracy of failure probability calculations. Finally, a set of benchmark problems is considered here to compare the MC and direct integration approaches, and a statistical failure analysis of compacts in the Advanced Gas Reactor (AGR)-2 experiments is performed using the direct integration approach.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multiscale, mechanistic modeling of cesium transport in silicon carbide for TRISO fuel performance prediction

Understanding cesium (Cs) transport in TRistructural ISOtropic (TRISO) particle fuel is crucial for predicting fission product release in high-temperature reactors. However, current challenges include significant scatter in diffusivity data and unexplained temperature-dependent diffusion regimes in the silicon carbide layer. This study addresses these challenges by developing a multiscale, mechanistic Cs transport model integrating atomistic simulations and phase field modeling. Our model quantifies temperature and grain size effects on Cs diffusivity, attributing experimentally observed regimes to a transition from bulk-dominated diffusivity at high temperatures to grain boundary-dominated diffusivity at lower temperatures. The model, validated against diffusion measurements and advanced gas reactor (AGR)-1 and AGR-2 post-irradiation fission product release data, enhances the predictive capability of the BISON fuel performance code. This study advances our understanding of Cs release from TRISO particles and its dependence on temperature and silicon carbide grain size, with implications for the safety and efficiency of high-temperature nuclear reactors.

BISON↗
DOE OSTI2022

AGR-2 irradiated TRISO particle IPyC/SiC interface analysis using FIB-SEM tomography

In this work, the morphology in the interface region between the inner pyrolytic carbon layer (IPyC) and silicon carbide (SiC) layers in tristructural-isotropic (TRISO) particle fuel from the AGR-2 irradiation experiment were studied using focused ion beam-scanning electron microscopy tomography. This work quantitatively described the interface and corresponding relevant metrics to understand how the microstructural features at the IPyC/SiC interface may influence actinide and fission product interactions with the SiC layer. Particles were selected with varied 110m Ag retention rates, and their volumes were reconstructed and analyzed for distributions of pores, fission product/actinide features, SiC, and IPyC. It was found that porosity accommodates fission products in the interface and SiC layers. The largest fission product/actinide precipitates were found in the interface region. This was also where the largest number fraction of fission products/actinides was found, consistent with SEM showing fission product/actinide pileup along selected areas of the interface region.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Options for the Removal of Cesium and Strontium from Acidic Uranyl Sulfate Solutions from Molybdenum-99 Production: Part II The Effect of Sodium Carbonate Adjustment to pH 9 on Strontium Removal

A small laboratory-scale column process aimed at removing fission products from prototypical acidic sulfate solution wastes from a prototypical Mo-99 recovery process has been operated in a radioactive materials hood at Savannah River National Laboratory. This equipment has been operated with realistic concentrations of uranium (0.4 wt % 235 U), plutonium ( 239 Pu), neptunium ( 237 Np), non-radioactive surrogates of common fission products (including Cs and Sr) and two promising absorbents – AMP-PAN and CST R9120-B. The goal of this work was to demonstrate the removal and concentration of high specific activity isotopes which are expected to dominate the classification of the low-level waste from the production of 99 Mo. Both AMP-PAN and CST R9120-B are attractive absorbents for the removal of 137 Cs from an acidic sulfate waste stream. They do not provide a solution for the removal of 90 Sr from the acidic solutions. CST was shown to be useful at removing both Cs and Sr after adjustment of the acidic sulfate solution with sodium carbonate to pH 9. Limited removal of transuranic species and almost no removal of uranium was observed for CST R9120B absorbent. This could be important due to the relatively large amount of uranium expected to be present in such waste streams. The capacity of these absorbents for 137 Cs will likely be dependent on the Cs concentration in the solutions processed but loading in excess of 0.7 mg Cs per gram of CST absorbent while loading 0.14 mg Sr per gram of CST absorbent appears to be achievable from pH 9 carbonate solution.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Verification of Triso Fuel Burnup Using Machine Learning Algorithms

Pebble Bed Reactors are fueled with fuel pebbles that are circulated multiple times through the reactor vessel before discharge. During the normal operation of a PBR, ejected pebbles are returned to the reactor or discharged depending on the fuel burnup and physical condition of the pebbles. The burnup measurement is usually based on detected radiation signatures of fission products accumulated in the pebble fuel over burnup. Previous research has shown that height of photopeaks of fission products, such as 134 Cs, 137 Cs, 154 Eu, etc., can be used independently or in combination to infer or predict the level of burnup in the fuel. However, it remains challenging to measure such complex sources due to self-shielding effects, strong radiation background and intervening materials. Another operational challenge is the required high throughput of burnup measurement, which necessitates limited measurement time and thus impacts quality of measured gamma-ray spectra. Hence, advanced spectral analysis methods are needed to analyze the noisy gamma spectra and predict the burnup values. We propose to use machine learning (ML) method to interpret gamma-ray spectra and predict the burnup values of the pebbles. ML has achieved widespread success and adoption across a few domains that require pattern recognition and analysis in varied data types. In this work, we apply three proven ML approaches - multilayer perceptrons, convolutional neural networks, and transformers - to the task of predicting fuel burnup from measured gamma spectra, and compile a dataset of simulated spectra for training and validation of the ML models. In this paper, we will discuss the network architecture of these three ML approaches and compare the performance of the simplest of these (MLP) to a standard linear regression.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗