SEARCH · Engineering Papers
Results for “feedback control”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Fault tolerant control laws
A systematic procedure for the synthesis of fault tolerant control laws to actuator failure has been presented. Two design methods were used to synthesize fault tolerant controllers: the conventional LQ design method and a direct feedback controller design method SANDY. The latter method is used primarily to streamline the full-state Q feedback design into a practical implementable output feedback controller structure. To achieve robustness to control actuator failure, the redundant surfaces are properly balanced according to their control effectiveness. A simple gain schedule based on the landing gear up/down logic involving only three gains was developed to handle three design flight conditions: Mach .25 and Mach .60 at 5000 ft and Mach .90 at 20,000 ft. The fault tolerant control law developed in this study provides good stability augmentation and performance for the relaxed static stability aircraft. The augmented aircraft responses are found to be invariant to the presence of a failure. Furthermore, single-loop stability margins of +6 dB in gain and +30 deg in phase were achieved along with -40 dB/decade rolloff at high frequency.
Station Keeping of Small Outboard-Powered Boats
Three station keeping controllers have been developed which work to minimize displacement of a small outboard-powered vessel from a desired location. Each of these three controllers has a common initial layer that uses fixed-gain feedback control to calculate the desired heading of the vessel. A second control layer uses a common fixed-gain feedback controller to calculate the net forward thrust, one of two algorithms for controlling engine angle (Fixed-Gain Proportional-integral-derivative (PID) or PID with Adaptively Augmented Gains), and one of two algorithms for differential throttle control (Fixed-Gain PID and PID with Adaptive Differential Throttle gains), which work together to eliminate heading error. The three selected controllers are evaluated using a numerical simulation of a 33-foot center console vessel with twin outboards that is subject to wave, wind, and current disturbances. Each controller is tested for its ability to maintain position in the presence of three sets of environmental disturbances. These algorithms were tested with current velocity of 1.5 m/s, significant wave height of 0.5 m, and wind speeds of 2, 5, and 10 m/s. These values were chosen to model conditions a small vessel may experience in the Gulf Stream off of Fort Lauderdale. The Fixed-gain PID controller progressively got worse as wind speeds increased, while the controllers using adaptive methodologies showed consistent performance over all weather conditions and decreased heading error by as much as 20%. Thus, enhanced robustness to environmental changes has been gained by using an adaptive algorithm.
Performance analysis of the advanced thermal control flight experiment
Flight data for the different operational modes of the advanced thermal control flight experiment are presented and compared with ground-test data. Performance of the system with feedback control is compared to performance without such control, and performances of the individual components are analyzed. Finally, changes in performance from launch through March 31, 1975, are discussed and analyzed. All thermal control components are performing as predicted for the existing flight environment. However, the daily reservoir and radiator temperatures during peak solar input are greater than those experienced in ground acceptance tests. These increased temperatures have resulted in a loss of control by the feedback-controlled variable-conductance heat pipe for several hours around the period of maximum insolation. The higher temperatures are apparently due to contamination and/or degradation of the second-surface mirrors which cover the reservoir and radiator.
Nonlinear optimal control with tensors - Some computational issues
Some computational issues associated with the calcualtion of optimal feedback controls for nonlinear systems in a tensor setting are described. The specific issues addressed pertain to the combinatorial nature of the loading of the elements into tensors used to represent the system, cost, and feedback, and the subsequent calculations involving these elements. Particular attention is given to: the symmetric tensor algebra which is a natural setting for representing polynomials; the conversions between symmetric and nonsymmetric tensors; the general nature of the calculations required; and the solution equation for nonlinear optimal feedback control. It is concluded that nonlinear tensor feedback can improve performance both in terms of system responses and in terms of system stability region.
Pilot-optimal multivariable control synthesis by output feedback
A control system design approach for optimal stability augmentation, systems, using limited state feedback theory with the specific inclusion of the human pilot in the loop is presented. The methodology is especially suitable for application to flight vehicles exhibiting nonconventional dynamic characteristics and for which quantitative handling qualities specifications are not available. The design is based on a correlation between pilot ratings and objective function of the optimal control model of the human pilot. Simultaneous optimization for augmentation and pilot gains are required.
Heat Control via Torque Control in Friction Stir Welding
In a proposed advance in friction stir welding, the torque exerted on the workpiece by the friction stir pin would be measured and controlled in an effort to measure and control the total heat input to the workpiece. The total heat input to the workpiece is an important parameter of any welding process (fusion or friction stir welding). In fusion welding, measurement and control of heat input is a difficult problem. However, in friction stir welding, the basic principle of operation affords the potential of a straightforward solution: Neglecting thermal losses through the pin and the spindle that supports it, the rate of heat input to the workpiece is the product of the torque and the speed of rotation of the friction stir weld pin and, hence, of the spindle. Therefore, if one acquires and suitably processes data on torque and rotation and controls the torque, the rotation, or both, one should be able to control the heat input into the workpiece. In conventional practice in friction stir welding, one uses feedback control of the spindle motor to maintain a constant speed of rotation. According to the proposal, one would not maintain a constant speed of rotation: Instead, one would use feedback control to maintain a constant torque and would measure the speed of rotation while allowing it to vary. The torque exerted on the workpiece would be estimated as the product of (1) the torque-multiplication ratio of the spindle belt and/or gear drive, (2) the force measured by a load cell mechanically coupled to the spindle motor, and (3) the moment arm of the load cell. Hence, the output of the load cell would be used as a feedback signal for controlling the torque (see figure).
A new algorithm for suboptimal stochastic control.
M measurement optimal feedback control algorithm for stochastic discrete time systems, considering nonlinear plant, constrained controls, nonquadratic cost and simulations
A new algorithm for suboptimal stochastic control
M measurement optimal feedback control algorithm for stochastic discrete time systems, considering nonlinear plant, constrained controls, nonquadratic cost and simulations
Passive stabilization for large space systems
The optimal tuning of multiple tuned-mass dampers for the transient vibration damping of large space structures is investigated. A multidisciplinary approach is used. Structural dynamic techniques are applied to gain physical insight into absorber/structure interaction and to optimize specific cases. Modern control theory and parameter optimization techniques are applied to the general optimization problem. A design procedure for multi-absorber multi-DOF vibration damping problems is presented. Classical dynamic models are extended to investigate the effects of absorber placement, existing structural damping, and absorber cross-coupling on the optimal design synthesis. The control design process for the general optimization problem is formulated as a linear output feedback control problem via the development of a feedback control canonical form. The techniques are applied to sample micro-g and pointing problems on the NASA dual keel space station.
Optimal control of measurement subsystems.
Optimal control of measurement subsystems within feedback control systems
Isolation of crystallizing droplets by electrostatic levitation
The principles of electrostatic levitation where the positioning and stabilization of a sample are accomplished by applying appropriate electrostatic forces to a charged sample are outlined, and attention is focused on a feedback control algorithm, drop-launching method, and four-drop levitator. Drop levitation in 1-g is discussed, and crystal-growth experiments are presented. An experiment in which the protein concentration of a levitated drop is controlled by a feedback system is described. During levitation, the drop evaporation rate is controlled in a programmed way in order to acquire proper protein concentration levels for both nucleation and growth. The containerless approach of protein crystal growth when applied in the space environment is assessed.
Telerobotic control of a mobile coordinated robotic server
The annual report on telerobotic control of a mobile coordinated robotic server is presented. The goal of this effort is to develop advanced control methods for flexible space manipulator systems. As such, an adaptive fuzzy logic controller was developed in which model structure as well as parameter constraints are not required for compensation. The work builds upon previous work on fuzzy logic controllers. Fuzzy logic controllers have been growing in importance in the field of automatic feedback control. Hardware controllers using fuzzy logic have become available as an alternative to the traditional PID controllers. Software has also been introduced to aid in the development of fuzzy logic rule-bases. The advantages of using fuzzy logic controllers include the ability to merge the experience and intuition of expert operators into the rule-base and that a model of the system is not required to construct the controller. A drawback of the classical fuzzy logic controller, however, is the many parameters needed to be turned off-line prior to application in the closed-loop. In this report, an adaptive fuzzy logic controller is developed requiring no system model or model structure. The rule-base is defined to approximate a state-feedback controller while a second fuzzy logic algorithm varies, on-line, parameters of the defining controller. Results indicate the approach is viable for on-line adaptive control of systems when the model is too complex or uncertain for application of other more classical control techniques.
Multivariable control for the F-100 engine using the LQG/LTR methodology
The design of a multivariable feedback control system for the Pratt and Whitney F-100 turbofan jet engine is a challenging task for control engineers. This paper employs a linearized model of the F-100 engine to demonstrate the use of the newly developed Linear Quadratic Gaussian/Loop Transfer Recovery (LQG/LTR) design methodology, which adopts an integrated frequency-domain and time-domain approach to multivariable feedback control synthesis so as to meet stability-robustness, command-following, and disturbance-rejection specifications.
Application of the MNA design method to a nonlinear turbofan engine
Using nonlinear digital simulation as a representative model of the dynamic operation of the QCSEE turbofan engine, a feedback control system is designed by variable frequency design techniques. Transfer functions are generated for each of five power level settings covering the range of operation from approach power to full throttle (62.5% to 100% full power). These transfer functions are then used by an interactive control system design synthesis program to provide a closed loop feedback control using the multivariable Nyquist array and extensions to multivariable Bode diagrams and Nichols charts.
Method for Real-Time State Estimation of Structural Modes for an Aeroelastic Wind Tunnel Model
A method for estimating displacements, velocities, and accelerations of structural modes in generalized coordinates from measured sensor data in real time is developed and demonstrated. Data from conventional strain gauges and fiber optic strain sensors (FOSS) were combined with strain mode shapes to produce least-squares estimates of the structural mode displacements. Similarly, accelerometer data were combined with displacement mode shapes to estimate structural mode accelerations. Estimates were then combined using a Kalman filter to refine the displacement estimates and produce structural mode velocity estimates. The approach was demonstrated using simulation data for the NASA-Boeing collaboration called the Integrated Adaptive Wing Technology Maturation (IAWTM) project in both a stable open-loop condition and an unstable condition where estimated displacement and velocity states were used for feedback control. Results supported the feasibility of using this approach for feedback control and system identification applications for wind tunnel tests.
Multi-Objective Optimal Control of High Aspect Ratio Wing Wind Tunnel Model
This paper presents the design of a multi-objective optimal controller for the 13.5 aspect ratio Common Research Model (CRM) wind tunnel model. A Pareto front analysis is performed to provide the optimal tradeoff between the competing objectives - gust load alleviation, maneuver load alleviation, and drag minimization - so that the weighting matrices for the control law are selected optimally. Also presented are two formulations of the controller: a state feedback with Kalman filter design, and an output feedback form where sensors are used directly for feedback control. The controller demonstrates a reduced peak-to-peak strain of 45.78% while also reducing drag and mean bending moment. An output feedback formulation for gust load alleviation is formulated and produces a 53% reduction in the strain response due to a gust input.
Active transition fixing and control of the boundary layer in air
Active transition of flow over an airfoil surface and feedback control by sound is investigated in a wind tunnel at Caltech. Laminar instability forced by localized time dependent nonintrusive narrow heating strip causes abrupt changes in velocity to trigger instant transition at favorable pressure gradient. At zero and adverse pressure gradients these changes are only marginal. Feedback control by sound interaction at nearly normal incidence produces significant reduction in velocity perturbation in regions of transition. This reduction is in part at the expense of an increase in background disturbance since it is not possible to restore the flow to its undisturbed state.