Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “differential filter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 343 records · Page 19

Double symbol error rates for differential detection of narrow-band FM

This paper evaluates the double symbol error rate (average probability of two consecutive symbol errors) in differentially detected narrow-band FM. Numerical results are presented for the special case of MSK with a Gaussian IF receive filter. It is shown that, not unlike similar results previously obtained for the single error probability of such systems, large inaccuracies in predicted performance can occur when intersymbol interference is ignored.

Simon, M. K.↗

C-20A/GIII Precision Autopilot Development in Support of NASA's UAVSAR Program

The NASA Unmanned Aerial Vehicle Synthetic Aperture Radar (UAVSAR) program is developing a Synthetic Aperture Radar (SAR) for ground measurements. A key element for the success of this program is a Platform Precision Autopilot (PPA). An interim vehicle (NASA C-20AJGlll) was selected to carry the radar pod and develop the PPA. The PPA interfaces with the C- 20AIG Ill aircraft by imitating the output of an Instrument Landing System (ILS) approach. This technique retains the safeguards in the aircraft's autopilot. The PPA entered initial flight testing in early 2007. The PPA uses a Kalman filter to generate a real-time position solution with information from the C-20AIGIII and a real-time differential GPS unit designed by JPL. The real-time navigation solution is used to compute commands (Guidance and Control subsystems) which in turn drive two modified ILS testers. The ILS tester units produce modulated RF signals fed to the onboard navigation receiver. These correction signals allow the C-20NGIII autopilot to fly a simulated ILS approach that meets the PPA requirements for UAVSAR applications. The PPA requirement is to make repeat pass flights within a ten meter tube over a 200 kilometer course in conditions of cairn to light turbulence. Flight test results are expected to be available at the time of the NASA Science Technology Conference 2007

Lee, James A.↗

Advanced Sine Wave Modulation of Continuous Wave Laser System for Atmospheric CO2 Differential Absorption Measurements

NASA Langley Research Center in collaboration with ITT Exelis have been experimenting with Continuous Wave (CW) laser absorption spectrometer (LAS) as a means of performing atmospheric CO2 column measurements from space to support the Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) mission.Because range resolving Intensity Modulated (IM) CW lidar techniques presented here rely on matched filter correlations, autocorrelation properties without side lobes or other artifacts are highly desirable since the autocorrelation function is critical for the measurements of lidar return powers, laser path lengths, and CO2 column amounts. In this paper modulation techniques are investigated that improve autocorrelation properties. The modulation techniques investigated in this paper include sine waves modulated by maximum length (ML) sequences in various hardware configurations. A CW lidar system using sine waves modulated by ML pseudo random noise codes is described, which uses a time shifting approach to separate channels and make multiple, simultaneous online/offline differential absorption measurements. Unlike the pure ML sequence, this technique is useful in hardware that is band pass filtered as the IM sine wave carrier shifts the main power band. Both amplitude and Phase Shift Keying (PSK) modulated IM carriers are investigated that exibit perfect autocorrelation properties down to one cycle per code bit. In addition, a method is presented to bandwidth limit the ML sequence based on a Gaussian filter implemented in terms of Jacobi theta functions that does not seriously degrade the resolution or introduce side lobes as a means of reducing aliasing and IM carrier bandwidth.

Campbell, Joel F.↗

Hydrophobic Filter Material for Nuclear Material Transportation and Storage Containers - 17518

Los Alamos National Laboratory has begun development of hydrophobic or super-hydrophobic inorganic filter materials that resist water ingress after exposure to radiation and/or elevated temperature. Filters that are currently available depend on carbon composites and/or organic polymers for their water resistant/hydrophobic properties to minimize water ingress. However, facility and transportation accident scenarios often include fire, impact and subsequent water spray or flooding conditions. A purely inorganic hydrophobic filter material could have enhanced resistance to fire and radiation damage, and continue to minimize water ingress after such an accident. Such filters could broaden the use of filtered containers in the transportation and storage of nuclear materials, and could have broader implications in other industrial applications. The goal is to create a porous inorganic material with hydrophobic properties that maintains or exceeds the current performance criteria for particulate filtration efficiency, pressure differential, air flow and hydrogen diffusion. The materials developed in this project show promise in evaluations for use as enhancements to the SAVY 4000 nuclear storage container that is becoming widely used around the DOE complex. Preliminary results indicate that the treated filters provide resistance to a water column pressure test and have filtration efficiencies and air flow pressure drops that meet the current performance criteria. There are various treatment options being tested to help determine the best path forward. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Hybrid optimization and Bayesian inference techniques for a non-smooth radiation detection problem

In this paper, we propose several algorithms to recover the location and intensity of a radiation source located in a simulated 250 × 180 m block of an urban center based on synthetic measurements. Radioactive decay and detection are Poisson random processes, so we employ likelihood functions based on this distribution. Owing to the domain geometry and the proposed response model, the negative logarithm of the likelihood is only piecewise continuous differentiable, and it has multiple local minima. To address these difficulties, we investigate three hybrid algorithms composed of mixed optimization techniques. For global optimization, we consider simulated annealing, particle swarm, and genetic algorithm, which rely solely on objective function evaluations; that is, they do not evaluate the gradient in the objective function. By employing early stopping criteria for the global optimization methods, a pseudo-optimum point is obtained. This is subsequently utilized as the initial value by the deterministic implicit filtering method, which is able to find local extrema in non-smooth functions, to finish the search in a narrow domain. These new hybrid techniques, combining global optimization and implicit filtering address, difficulties associated with the non-smooth response, and their performances, are shown to significantly decrease the computational time over the global optimization methods. To quantify uncertainties associated with the source location and intensity, we employ the delayed rejection adaptive Metropolis and DiffeRential Evolution Adaptive Metropolis algorithms. Finally, marginal densities of the source properties are obtained, and the means of the chains compare accurately with the estimates produced by the hybrid algorithms.

42 ENGINEERING↗

Gain Filtering for Single-Spatial-Mode Operation of Large-Mode-Area Fiber Amplifiers

Gain filtering of higher order modes in large-mode-area fibers is an extremely robust method for providing diffraction-limited performance regardless of core diameter or input beam quality. Analytic calculations demonstrate that reducing the diameter of the gain dopants compared to the waveguide diameter produces differential gain that is higher for the fundamental mode than all other fiber modes at all saturation levels. Matching the gain dopant to the mode profile is not as beneficial as a simple step profile since the primarymechanism of gain filtering is to deny gain toward the edge of the waveguide where most of the higher order mode power is contained. Numerical simulations of multikilowatt fiber amplifiers with up to 100-μm-diameter cores show that gain filtering is extremely robust, providing 99% of the output power in the fundamental mode output with only 90% of the seed power in the fundamental mode. Even with poor seed launch with 50% of the power in the fundamental mode, gain filtering can provide up to 90% of the output power in the fundamental mode.

fiber amplifiers↗

High-performance double-filter soft x-ray diagnostic for measurement of electron temperature structure and dynamics

A new soft x-ray (SXR) T{sub e} and tomography diagnostic has been developed for MST that can be used for simultaneous SXR spectrum measurement, tomographically reconstructed emissivity, and reconstructed and line-of-sight electron temperature. The diagnostic utilizes high-performance differential transimpedance amplifiers (gain 10{sup 5}-10{sup 9}) to provide fast time response (up to 125 kHz), allowing for the study of plasma structure dynamics. SXR double-foil T{sub e} measurements are consistent with Thomson scattering. SXR brightness through a variety of filter thicknesses has been combined with charge exchange recombination spectroscopy (CHERS) impurity density measurements to determine the plasma energy spectrum. Magnetic pickup from the fluctuating magnetic fields in the plasma (B(tilde sign){approx}20 gauss at 10-20 kHz) has been dramatically reduced by improving the detector and housing design, so that nanoampere diode currents are now measured without interference from the substantial fluctuating magnetic field incident on the plasma facing surface of the probe.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Identification of Differential Gene Expression Patterns after Acute Exposure to High and Low Doses of Low-LET Ionizing Radiation in a Reconstituted Human Skin Tissue

Our goal here was to identify dose and temporal dependent radiation responses in a complex tissue, reconstituted human skin. Direct sequencing of RNA (RNA-seq) was used to quantify altered transcripts following exposure to 0.1, 2 and 10 Gy of ionizing radiation at 3 and 8 hours. These doses include a low dose in the range of some medical diagnostic procedures (0.1 Gy), a dose typically received during radiotherapy (2.0 Gy) and a lethal dose (10 Gy). These doses could be received after an intentional or accidental radiation exposure and biomarkers are needed to rapidly and accurately triage exposed individuals. A total of 1701 genes were deemed to be significantly affected by high dose radiation exposure with the majority of genes affected at 10 Gy. A group of 29 genes including GDF15, BBC3, PPM1D, FDXR, GADD45A, MDM2, CDKN1A, TP53INP1, CYCSP27, SESN1, SESN2, PCNA, and AEN were similarly altered at both 2 and 10 Gy, but not 0.1 Gy, at multiple time points. A much larger group of up regulated genes, including those involved in inflammatory responses, was significantly altered only after a 10 Gy exposure. At high doses, down regulated genes were associated with cell cycle regulation and exhibited an apparent linear response between 2 and 10 Gy. While only a handful of genes were significantly affected by 0.1 Gy exposure using stringent statistical filters, groups of related genes regulating cell cycle progression and inflammatory responses consistently exhibited opposite trends in their regulation compared to the high dose exposures. Differential regulation of PLK1 signaling at low and high doses was confirmed using qRT-PCR. These results indicate that some alterations in gene expression are qualitatively different at low and high doses of radiation in this model system.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Grating-based phase contrast tomosynthesis imaging: Proof-of-concept experimental studies

Purpose: This paper concerns the feasibility of x-ray differential phase contrast (DPC) tomosynthesis imaging using a grating-based DPC benchtop experimental system, which is equipped with a commercial digital flat-panel detector and a medical-grade rotating-anode x-ray tube. An extensive system characterization was performed to quantify its imaging performance. Methods: The major components of the benchtop system include a diagnostic x-ray tube with a 1.0 mm nominal focal spot size, a flat-panel detector with 96 μm pixel pitch, a sample stage that rotates within a limited angular span of ±30°, and a Talbot-Lau interferometer with three x-ray gratings. A total of 21 projection views acquired with 3° increments were used to reconstruct three sets of tomosynthetic image volumes, including the conventional absorption contrast tomosynthesis image volume (AC-tomo) reconstructed using the filtered-backprojection (FBP) algorithm with the ramp kernel, the phase contrast tomosynthesis image volume (PC-tomo) reconstructed using FBP with a Hilbert kernel, and the differential phase contrast tomosynthesis image volume (DPC-tomo) reconstructed using the shift-and-add algorithm. Three inhouse physical phantoms containing tissue-surrogate materials were used to characterize the signal linearity, the signal difference-to-noise ratio (SDNR), the three-dimensional noise power spectrum (3D NPS), and the through-plane artifact spread function (ASF). Results: While DPC-tomo highlights edges and interfaces in the image object, PC-tomo removes the differential nature of the DPC projection data and its pixel values are linearly related to the decrement of the real part of the x-ray refractive index. The SDNR values of polyoxymethylene in water and polystyrene in oil are 1.5 and 1.0, respectively, in AC-tomo, and the values were improved to 3.0 and 2.0, respectively, in PC-tomo. PC-tomo and AC-tomo demonstrate equivalent ASF, but their noise characteristics quantified by the 3D NPS were found to be different due to the difference in the tomosynthesis image reconstruction algorithms. Conclusions: It is feasible to simultaneously generate x-ray differential phase contrast, phase contrast, and absorption contrast tomosynthesis images using a grating-based data acquisition setup. The method shows promise in improving the visibility of several low-density materials and therefore merits further investigation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

47 Tuc in Rubin Data Preview 1. Exploring Early LSST Data and Science Potential

We present analyses of the early data from Rubin Observatory’s Data Preview 1 (DP1) for the field of the globular cluster 47 Tuc. The DP1 data set for 47 Tuc includes four nights of observations from the Rubin Commissioning Camera (LSSTComCam), covering multiple bands (ugriy). We address challenges of crowding in the inner region of the cluster and toward the SMC in DP1, and demonstrate improved star–galaxy separation by fitting fifth-degree polynomials to the stellar loci in color–color diagrams and applying multidimensional sigma clipping. We compile a catalog of 3576 probable 47 Tuc member stars selected via a combination of isochrone, Gaia proper-motion, and color–color space matched filtering. We explore the sources of photometric scatter in the 47 Tuc color–color sequence, evaluating contributions from various potential sources, including differential extinction within the cluster. Finally, of the 72 well-characterized variables in the field, we recover three known variable stars, including two RR Lyrae and one eclipsing binary, in the coadd-based object catalog, and identify 62 in the difference image-based object catalog. Although the DP1 lightcurves have sparse temporal sampling, they appear to follow the patterns of densely sampled literature lightcurves well. Despite some data limitations for crowded-field stellar analysis, DP1 demonstrates the promising scientific potential for future LSST data releases.

Choi, Yumi [NSF National Optical-Infrared Astronom↗

Infrared studies of the circumsolar and night sky, April 1968 - 30 November 1971

A program is summarized of infrared studies of the circumsolar and night sky conducted between April, 1968, and November 30, 1971, at the University of New Mexico. In addition to observations performed at Capillo Peak Observatory in New Mexico, airborne observations from the Ames Research Center's CV990 were performed in 1968, and eclipses in Siberia (1968) and southern Mexico (1970) were observed. Two dual-channel filter photometers covering wavelengths in the 0.8 to 4.8 micron range were constructed for the aircraft and eclipse observations. A single channel differential photometer was constructed for daytime circumsolar observations. Two large-aperture (12 inch and 24 inch) photometers have been constructed for twilight and night sky photometry. Finally, a small spectrograph for eclipse work has been constructed. It has been used for airglow observations also. Other specialized instrumentation include a four-axis mounting for radial scanning with the eclipse photometers and a 14-inch diameter collimator for use with a black body in calibration of the photometers. The observations performed are included.

Peterson, A. W.↗

Dispensing Small Measured Volumes of Liquid

Dispensing unit measures, filters, and unloads oil into container. Used in automobile manufacturing to dispense antifreeze solution into radiators or oil into engines, transmissions, or differentials. Uses gaseous nitrogen to control pressure, flow rate, and quality precisely, with minimal contamination from atmosphere.

Larson, G.↗

BELINDA: Broadband Emission Lidar with Narrowband Determination of Absorption. A new concept for measuring water vapor and temperature profiles

We present a new concept for differential absorption lidar measurements of water vapor and temperature profiles. The idea is to use one broadband emission laser and a narrowband filter system for separation of the 'online' and 'offline' return signals. It is shown that BELINDA offers improvements as to laser emission shape and stability requirements, background suppression, and last and most important a significant reduction of the influence of Rayleigh scattering. A suitably designed system based on this concept is presented, capable of measuring water vapor or temperature profiles throughout the planetary boundary layer.

Theopold, F. A.↗

Multimodal differential emission measure in the solar corona

The Atmospheric Imaging Assembly (AIA) telescope on board the Solar Dynamics Observatory provides coronal extreme ultraviolet imaging over a broader temperature sensitivity range than the previous generations of instruments (Extreme Ultraviolet Imager; EUVI, EIT, and TRACE). Differential emission measure tomography (DEMT) of the solar corona based on AIA data is presented here for the first time. The main product of DEMT is the three-dimensional distribution of the local differential emission measure (LDEM). While in previous studies, based on EIT or EUVI data, there were three available EUV bands, the present study is based on the four cooler AIA bands (aimed at studying the quiet sun). The AIA filters allow exploration of new parametric LDEM models. Since DEMT is better suited for lower activity periods, we use data from Carrington Rotation 2099, when the Sun was in its most quiescent state during the AIA mission. Also, we validate the parametric LDEM models by using them to perform a bi-dimensional differential emission measure (DEM) analysis on sets of simultaneous AIA images, and comparing results with those obtained using other methods. Our study reveals a ubiquitous bimodal LDEM distribution in the quiet diffuse corona, characterized by two well-defined average centroid temperatures 〈T{sub 0,1}〉=(1.47±0.05) MK and 〈T{sub 0,2}〉=(2.57±0.05) MK. We argue that the nanoflare heating scenario is less likely to explain these results, and that alternative mechanisms, such as wave dissipation, appear better supported by our results.

79 ASTRONOMY AND ASTROPHYSICS↗

Optoelectronic simulation of GaAs solar cells with angularly selective filters

We discuss the influence of angularly selective filters on thin film gallium arsenide solar cells. For this reason, the detailed balance model was refined to fit our needs with respect to Auger recombination, reflection, transmission, and realistic absorption. For calculating real systems, an approach was made to include optical effects of angularly selective filters into electron-hole dynamic equations implemented in PC1D, a one dimensional solar cell calculation tool. With this approach, we find a relative V{sub oc} increase of 5% for an idealized 100 nm GaAs cell, including Auger recombination.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Convolutions on the sphere: commutation with differential operators

We generalize the definition of convolution of vectors and tensors on the 2-sphere, and prove that it commutes with differential operators. Moreover, vectors and tensors that are normal/tangent to the spherical surface remain so after the convolution. These properties make the new filtering operation particularly useful to analyzing and modeling nonlinear dynamics in spherical systems, such as in geophysics, astrophysics, and in inertial confinement fusion applications. An essential tool we use is the theory of scalar, vector, and tensor spherical harmonics. We then show that our generalized filtering operation is equivalent to the (traditional) convolution of scalar fields of the Helmholtz decomposition of vectors and tensors.

42 ENGINEERING↗

True randomness from an incoherent source

Quantum random number generators (QRNGs) harness the intrinsic randomness in measurement processes: the measurement outputs are truly random, given the input state is a superposition of the eigenstates of the measurement operators. In the case of trusted devices, true randomness could be generated from a mixed state ρ so long as the system entangled with ρ is well protected. We propose a random number generation scheme based on measuring the quadrature fluctuations of a single mode thermal state using an optical homodyne detector. By mixing the output of a broadband amplified spontaneous emission (ASE) source with a single mode local oscillator (LO) at a beam splitter and performing differential photo-detection, we can selectively detect the quadrature fluctuation of a single mode output of the ASE source, thanks to the filtering function of the LO. Experimentally, a quadrature variance about three orders of magnitude larger than the vacuum noise has been observed, suggesting this scheme can tolerate much higher detector noise in comparison with QRNGs based on measuring the vacuum noise. The high quality of this entropy source is evidenced by the small correlation coefficients of the acquired data. A Toeplitz-hashing extractor is applied to generate unbiased random bits from the Gaussian distributed raw data, achieving an efficiency of 5.12 bits per sample. Furthermore, the output of the Toeplitz extractor successfully passes all the NIST statistical tests for random numbers.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Privacy-Preserving Aggregation of Controllable Loads to Compensate Fluctuations in Solar Power

Cybersecurity and privacy are of the utmost importance for safe, reliable operation of the electric grid. It is well known that the increased connectivity/interoperability between all stakeholders (e.g., utilities, suppliers, and consumers) will enable personal information collection. Significant advanced metering infrastructure (AMI) deployment and demand response (DR) programs across the country, while enable enhanced automation, also generate energy data on individual consumers that can potentially be used for exploiting privacy. Inspired by existing works which consider DR, battery-based perturbation, and differential privacy noise adding, we novelly consider the aggregator (cluster) level privacy issue in the DR framework of solar photovoltaic (PV) generation following. Different from most of the existing works which mainly rely on the charging/discharging scheduling of rechargeable batteries, we utilize controllable building loads to serve as virtual storage devices to absorb a large portion of the PV genertaion while delicately keeping desired noisy terms to satisfy the differential privacy for the raw load profiles at the aggregator level. This not only ensures differential privacy, but also improves the DR efficiency in load following since part of the noisy signal in solar PV generation has been filtered out. In particular, a mixed integer quadratic optimization problem is formulated to optimally dispatch a population of on/off controllable loads to achieve this privacy-preserving DR service.

Dong, Jin↗